SLE-NETWORK-MIB: View SNMP OID List / Download MIB

VENDOR: DASAN CO.,LTD.


 Home MIB: SLE-NETWORK-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, IANAifType-MIB, DASAN-SMI, SLE-TC-MIB, INET-ADDRESS-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 sleNetwork 1.3.6.1.4.1.6296.101.11
This MIB contains all needed informations about DHCP and all supported sle DHCP features.
       sleNetInterface 1.3.6.1.4.1.6296.101.11.1
           sleNetIfTable 1.3.6.1.4.1.6296.101.11.1.1 no-access
Description.
               sleNetIfEntry 1.3.6.1.4.1.6296.101.11.1.1.1 no-access
Description.
                   sleNetIfIndex 1.3.6.1.4.1.6296.101.11.1.1.1.1 integer32 read-only
Network interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface index
                   sleNetIfName 1.3.6.1.4.1.6296.101.11.1.1.1.2 octet string read-only
Device Name of this Interface.
                   sleNetIfDescription 1.3.6.1.4.1.6296.101.11.1.1.1.3 octet string read-only
Description of this interface.
                   sleNetIfTableIndex 1.3.6.1.4.1.6296.101.11.1.1.1.4 interfaceindex read-only
Same as ifIndex (for appropriated ifTable entries).
                   sleNetIfRegState 1.3.6.1.4.1.6296.101.11.1.1.1.5 integer read-only
Registered state of Network device. Enumeration: 'unregistered': 0, 'registered': 1.
                   sleNetIfAdminState 1.3.6.1.4.1.6296.101.11.1.1.1.6 integer read-only
Administrative state. down - shutdown up - noshutdown Enumeration: 'down': 0, 'up': 1.
                   sleNetIfOperState 1.3.6.1.4.1.6296.101.11.1.1.1.7 integer read-only
Operational state. down - shutdown or not running up - running Enumeration: 'down': 0, 'up': 1.
                   sleNetIfMulticast 1.3.6.1.4.1.6296.101.11.1.1.1.8 integer read-only
Multicast enable/disable state. Enumeration: 'enable': 1, 'disable': 0.
                   sleNetIfMtu 1.3.6.1.4.1.6296.101.11.1.1.1.9 integer read-only
Maximum Transmission Unit.
                   sleNetIfIpSetMode 1.3.6.1.4.1.6296.101.11.1.1.1.10 integer read-only
IP address setting mode. 0 : static 1 : dynamic (by DHCP client) Enumeration: 'dynamic': 1, 'static': 0.
                   sleNetIfIpMartianFilter 1.3.6.1.4.1.6296.101.11.1.1.1.11 integer read-only
Description. Enumeration: 'enable': 1, 'disable': 0.
                   sleNetIfUpCnt 1.3.6.1.4.1.6296.101.11.1.1.1.12 integer32 read-only
The times of link-up event.
                   sleNetIfDownCnt 1.3.6.1.4.1.6296.101.11.1.1.1.13 integer32 read-only
The times of link-down event.
                   sleNetIfLinkUpTime 1.3.6.1.4.1.6296.101.11.1.1.1.14 counter64 read-only
The elapsed time after link is up.
                   sleNetIfElapsedTimeAfterClearStats 1.3.6.1.4.1.6296.101.11.1.1.1.15 counter64 read-only
The elapsed time after clearing status.
                   sleNetIfBindingVRFName 1.3.6.1.4.1.6296.101.11.1.1.1.16 octet string read-only
VRF name that this tunnel interface is binding.
                   sleNetIfOnFailUseVRF 1.3.6.1.4.1.6296.101.11.1.1.1.17 integer read-only
Lookup into a global routing table when the VRF routing table lookup was failed. Enumeration: 'enable': 1, 'disable': 2.
                   sleNetIfIpUnreachability 1.3.6.1.4.1.6296.101.11.1.1.1.18 integer read-only
IP unreachability ON/OFF Enumeration: 'enable': 1, 'disable': 2.
                   sleNetIfipRedirects 1.3.6.1.4.1.6296.101.11.1.1.1.19 integer read-only
Description. Enumeration: 'enable': 1, 'disable': 2.
                   sleNetIfIpForwarding 1.3.6.1.4.1.6296.101.11.1.1.1.20 integer read-only
The IP forwarding status Enumeration: 'enable': 1, 'disable': 0.
                   sleNetIfAlias 1.3.6.1.4.1.6296.101.11.1.1.1.21 octet string read-only
lias Name for the Interface
                   sleNetIfIpArpAlias 1.3.6.1.4.1.6296.101.11.1.1.1.22 integer read-only
IP Arp Alias state Enumeration: 'enable': 1, 'disable': 0.
                   sleNetIfIpArpAliasMac 1.3.6.1.4.1.6296.101.11.1.1.1.23 macaddress read-only
IP Arp Alias MAC
                   sleNetIfArpMCProbeCount 1.3.6.1.4.1.6296.101.11.1.1.1.24 integer32 read-only
ARP request Multicast probe count
                   sleNetIfArpUCProbeCount 1.3.6.1.4.1.6296.101.11.1.1.1.25 integer32 read-only
ARP request Unicast probe count
                   sleNetIfArpRetransTime 1.3.6.1.4.1.6296.101.11.1.1.1.26 integer32 read-only
Retrans time of ARP request (unit: 1s)
                   sleNetIfIpProxyArp 1.3.6.1.4.1.6296.101.11.1.1.1.27 integer read-only
IP Proxy Arp state Enumeration: 'enable': 1, 'disable': 0.
                   sleNetIfIpRPFilter 1.3.6.1.4.1.6296.101.11.1.1.1.28 integer read-only
IP Reverse Path Filtering of CPU Enumeration: 'strict': 2, 'disable': 0, 'loose': 1.
                   sleNetIfRPFilter 1.3.6.1.4.1.6296.101.11.1.1.1.29 integer read-only
Reverse Path Filtering of CHIP (default : looseAllow) Enumeration: 'strict': 2, 'disable': 0, 'loose': 1, 'looseAllow': 3.
                   sleNetIfRouteMap 1.3.6.1.4.1.6296.101.11.1.1.1.30 octet string read-only
IP Policy route-map name
           sleNetIfControl 1.3.6.1.4.1.6296.101.11.1.2
               sleNetIfControlRequest 1.3.6.1.4.1.6296.101.11.1.2.1 integer read-write
The request of a user command. Enumeration: 'setNetIfIpForwarding': 9, 'setNetIfRegState': 1, 'unsetNetIfBindingVRF': 5, 'setNetIfProfile': 2, 'setArpRetransTime': 14, 'setArpUCProbeCount': 13, 'setNetIfIpUnreachability': 7, 'setNetIfIpMartianFilter': 3, 'setNetIfIpRedirects': 8, 'setNetIfBindingVRF': 4, 'setArpMCProbeCount': 12, 'setIpArpAlias': 11, 'setRouteMap': 18, 'setNetIfOnFailUseVRF': 6, 'setAlias': 10, 'setIpProxyArp': 15, 'setIpRPFilter': 16, 'setRPFilter': 17.
               sleNetIfControlStatus 1.3.6.1.4.1.6296.101.11.1.2.2 slecontrolstatustype read-only
The status of a user command.
               sleNetIfControlTimer 1.3.6.1.4.1.6296.101.11.1.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleNetIfControlTimeStamp 1.3.6.1.4.1.6296.101.11.1.2.4 slecontrolrequestresulttype read-only
The time stamp of the last command (end of command).
               sleNetIfControlReqResult 1.3.6.1.4.1.6296.101.11.1.2.5 timeticks read-only
The result of the last user command.
               sleNetIfControlIndex 1.3.6.1.4.1.6296.101.11.1.2.6 integer32 read-write
Network interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface index
               sleNetIfControlDescription 1.3.6.1.4.1.6296.101.11.1.2.7 octet string read-write
Description of this interface.
               sleNetIfControlRegState 1.3.6.1.4.1.6296.101.11.1.2.8 integer read-write
Description. Enumeration: 'unregister': 0, 'register': 1.
               sleNetIfControlAdminState 1.3.6.1.4.1.6296.101.11.1.2.9 integer read-write
Administrative state. Enumeration: 'down': 0, 'up': 1.
               sleNetIfControlMulticast 1.3.6.1.4.1.6296.101.11.1.2.10 integer read-write
Multicast enable/disable state. Enumeration: 'enable': 1, 'disable': 0.
               sleNetIfControlMtu 1.3.6.1.4.1.6296.101.11.1.2.11 integer read-write
Maximum Transmission Unit.
               sleNetIfControlIpMartianFilter 1.3.6.1.4.1.6296.101.11.1.2.12 integer read-write
Description. Enumeration: 'enable': 1, 'disable': 0.
               sleNetIfControlBindingVRFName 1.3.6.1.4.1.6296.101.11.1.2.13 octet string read-write
VRF name that this tunnel interface is binding.
               sleNetIfControlOnFailUseVRF 1.3.6.1.4.1.6296.101.11.1.2.14 integer read-write
Lookup into a global routing table when the VRF routing table lookup was failed. Enumeration: 'enable': 1, 'disable': 2.
               sleNetIfControlIpUnreachability 1.3.6.1.4.1.6296.101.11.1.2.15 integer read-write
IP unreachability ON/OFF Enumeration: 'enable': 1, 'disable': 2.
               sleNetIfControlIpRedirects 1.3.6.1.4.1.6296.101.11.1.2.16 integer read-write
Description. Enumeration: 'enable': 1, 'disable': 2.
               sleNetIfControlIpForwarding 1.3.6.1.4.1.6296.101.11.1.2.17 integer read-write
The IP forwarding status Enumeration: 'enable': 1, 'disable': 0.
               sleNetIfControlAlias 1.3.6.1.4.1.6296.101.11.1.2.18 octet string read-write
Alias Name for the Interface
               sleNetIfControlIpArpAlias 1.3.6.1.4.1.6296.101.11.1.2.19 integer read-write
IP Arp Alias state Enumeration: 'enable': 1, 'disable': 0.
               sleNetIfControlIpArpAliasMac 1.3.6.1.4.1.6296.101.11.1.2.20 macaddress read-write
IP Arp Alias MAC
               sleNetIfControlArpMCProbeCount 1.3.6.1.4.1.6296.101.11.1.2.21 integer32 read-write
ARP request Multicast probe count
               sleNetIfControlArpUCProbeCount 1.3.6.1.4.1.6296.101.11.1.2.22 integer32 read-write
ARP request Unicast probe count
               sleNetIfControlArpRetransTime 1.3.6.1.4.1.6296.101.11.1.2.23 integer32 read-write
Retrans time of ARP request (unit: 1s)
               sleNetIfControlIpProxyArp 1.3.6.1.4.1.6296.101.11.1.2.24 integer read-write
IP Proxy Arp state Enumeration: 'enable': 1, 'disable': 0.
               sleNetIfControlIpRPFilter 1.3.6.1.4.1.6296.101.11.1.2.25 integer read-write
IP Reverse Path Filtering of CPU Enumeration: 'strict': 2, 'disable': 0, 'loose': 1.
               sleNetIfControlRPFilter 1.3.6.1.4.1.6296.101.11.1.2.26 integer read-write
Reverse Path Filtering of CHIP (default : looseAllow) Enumeration: 'strict': 2, 'disable': 0, 'loose': 1, 'looseAllow': 3.
               sleNetIfControlRouteMap 1.3.6.1.4.1.6296.101.11.1.2.27 octet string read-write
IP Policy route-map name
           sleNetIfNotification 1.3.6.1.4.1.6296.101.11.1.3
               sleNetIfRegStateChanged 1.3.6.1.4.1.6296.101.11.1.3.1
Description.
               sleNetIfProfileChanged 1.3.6.1.4.1.6296.101.11.1.3.2
setNetIfProfile.
               sleNetIfIpMartianFilterChanged 1.3.6.1.4.1.6296.101.11.1.3.3
Description.
               sleNetIfBindingVRFSet 1.3.6.1.4.1.6296.101.11.1.3.4
Description.
               sleNetIfBindingVRFUnset 1.3.6.1.4.1.6296.101.11.1.3.5
Description.
               sleNetIfIpOnFailUseVRFChanged 1.3.6.1.4.1.6296.101.11.1.3.6
Description.
               sleNetIfIpUnreachabilityChanged 1.3.6.1.4.1.6296.101.11.1.3.7
Description.
               sleNetIfIpRedirectsChanged 1.3.6.1.4.1.6296.101.11.1.3.8
Description.
               sleNetIfIpForwardingChanged 1.3.6.1.4.1.6296.101.11.1.3.9
setNetIfIpForwarding
               sleNetIfAliasChanged 1.3.6.1.4.1.6296.101.11.1.3.10
setAlias
               sleNetIfIpArpAliasChanged 1.3.6.1.4.1.6296.101.11.1.3.11
setIpArpAlias
               sleNetIfArpMCProbeCountChanged 1.3.6.1.4.1.6296.101.11.1.3.12
setArpMCProbeCount
               sleNetIfArpUCProbeCountChanged 1.3.6.1.4.1.6296.101.11.1.3.13
setArpUCProbeCount
               sleNetIfArpRetransTimeChanged 1.3.6.1.4.1.6296.101.11.1.3.14
setArpRetransTime
               sleNetIfIpProxyArpChanged 1.3.6.1.4.1.6296.101.11.1.3.15
setIpProxyArp
               sleNetIfIpRPFilterChanged 1.3.6.1.4.1.6296.101.11.1.3.16
setIpRPFilter
               sleNetIfRPFilterChanged 1.3.6.1.4.1.6296.101.11.1.3.17
setRPFilter
               sleNetIfRouteMapChanged 1.3.6.1.4.1.6296.101.11.1.3.18
setRouteMap
       sleIpAddress 1.3.6.1.4.1.6296.101.11.2
           sleIpAddrTable 1.3.6.1.4.1.6296.101.11.2.1 no-access
Description.
               sleIpAddrEntry 1.3.6.1.4.1.6296.101.11.2.1.1 no-access
Description.
                   sleIpAddrValue 1.3.6.1.4.1.6296.101.11.2.1.1.1 ipaddress read-only
The IP address to which this entry's addressing information pertains.
                   sleIpAddrMask 1.3.6.1.4.1.6296.101.11.2.1.1.2 integer32 read-only
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
                   sleIpAddrBcast 1.3.6.1.4.1.6296.101.11.2.1.1.3 ipaddress read-only
The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
                   sleIpAddrFlag 1.3.6.1.4.1.6296.101.11.2.1.1.4 bits read-only
Description. Bits: 'tentative': 1, 'deprecated': 2, 'permanent': 0, 'reserved5': 5, 'reserved4': 4, 'reserved6': 6, 'reserved3': 3, 'secondary': 7.
                   sleIpAddrScope 1.3.6.1.4.1.6296.101.11.2.1.1.5 integer read-only
Description. Enumeration: 'host': 254, 'global': 0, 'link': 253, 'site': 200, 'nowhere': 255.
                   sleIpAddrIpIndex 1.3.6.1.4.1.6296.101.11.2.1.1.6 integer read-only
The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
                   sleIpAddrUnnumUsedIp 1.3.6.1.4.1.6296.101.11.2.1.1.7 integer read-only
The Check a specific IP address for using interface unnumbered feature. Enumeration: 'none': 0, 'used': 1.
           sleIpAddrControl 1.3.6.1.4.1.6296.101.11.2.2
               sleIpAddrControlRequest 1.3.6.1.4.1.6296.101.11.2.2.1 integer read-write
The request of a user command. Enumeration: 'addIpIndex': 3, 'delIpIndex': 4, 'destroyIpAddress': 2, 'createIpAddress': 1.
               sleIpAddrControlStatus 1.3.6.1.4.1.6296.101.11.2.2.2 slecontrolstatustype read-only
The status of a user command.
               sleIpAddrControlTimer 1.3.6.1.4.1.6296.101.11.2.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleIpAddrControlTimeStamp 1.3.6.1.4.1.6296.101.11.2.2.4 slecontrolrequestresulttype read-only
The time stamp of the last command (end of command).
               sleIpAddrControlReqResult 1.3.6.1.4.1.6296.101.11.2.2.5 timeticks read-only
The result of the last user command.
               sleIpAddrControlNetIfIndex 1.3.6.1.4.1.6296.101.11.2.2.6 integer32 read-write
Network interface index 1..4094 : VLAN 10000..11023: Tunnel interface index
               sleIpAddrControlValue 1.3.6.1.4.1.6296.101.11.2.2.7 ipaddress read-write
The IP address to which this entry's addressing information pertains.
               sleIpAddrControlMask 1.3.6.1.4.1.6296.101.11.2.2.8 integer32 read-write
The subnet mask associated with the IP address of this entry.
               sleIpAddrControlFlag 1.3.6.1.4.1.6296.101.11.2.2.9 integer read-write
Description. Enumeration: 'primary': 0, 'secondary': 1.
               sleIpAddrControlScope 1.3.6.1.4.1.6296.101.11.2.2.10 integer read-write
Description. Enumeration: 'host': 254, 'global': 0, 'link': 253.
               sleIpAddrControlIpIndex 1.3.6.1.4.1.6296.101.11.2.2.11 integer read-write
The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
           sleIpAddrNotification 1.3.6.1.4.1.6296.101.11.2.3
               sleIpAddressCreated 1.3.6.1.4.1.6296.101.11.2.3.1
createIpAddress.
               sleIpAddressDestroyed 1.3.6.1.4.1.6296.101.11.2.3.2
destroyIpAddress.
               sleIpAddressIpIndexAdded 1.3.6.1.4.1.6296.101.11.2.3.3
addIpIndex
               sleIpAddressIpIndexDeleted 1.3.6.1.4.1.6296.101.11.2.3.4
delIpIndex
       sleArp 1.3.6.1.4.1.6296.101.11.3
           sleArpTable 1.3.6.1.4.1.6296.101.11.3.1 no-access
Description.
               sleArpEntry 1.3.6.1.4.1.6296.101.11.3.1.1 no-access
Description.
                   sleArpIpAddress 1.3.6.1.4.1.6296.101.11.3.1.1.1 ipaddress read-only
The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
                   sleArpPhyAddress 1.3.6.1.4.1.6296.101.11.3.1.1.2 macaddress read-only
The media-dependent `physical' address.
                   sleArpPortIndex 1.3.6.1.4.1.6296.101.11.3.1.1.3 integer32 read-only
The interface on which this entry's equivalence is effective. 0: for any ports.
                   sleArpState 1.3.6.1.4.1.6296.101.11.3.1.1.4 integer read-only
Arp entry's currently status. Enumeration: 'dynamic': 1, 'static': 0.
                   sleArpHwType 1.3.6.1.4.1.6296.101.11.3.1.1.5 integer read-only
Hardware Type of media. Enumeration: 'ethernet': 1.
                   sleArpHwUsed 1.3.6.1.4.1.6296.101.11.3.1.1.6 integer read-only
Arp entry's currently chip usage state. Enumeration: 'nonused': 0, 'used': 1.
                   sleArpUsedTime 1.3.6.1.4.1.6296.101.11.3.1.1.7 integer read-only
Arp entry's chip used time.(if sleArpState is 0, always 0 and if sleArpHwUsed is 0, always 0.)
           sleArpControl 1.3.6.1.4.1.6296.101.11.3.2
               sleArpControlRequest 1.3.6.1.4.1.6296.101.11.3.2.1 integer read-write
The request of a user command. Enumeration: 'destroyArpEntry': 2, 'clearArpTable': 3, 'clearArpTableByAddr': 4, 'createArpEntry': 1.
               sleArpControlStatus 1.3.6.1.4.1.6296.101.11.3.2.2 slecontrolstatustype read-only
The status of a user command.
               sleArpControlTimer 1.3.6.1.4.1.6296.101.11.3.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleArpControlTimeStamp 1.3.6.1.4.1.6296.101.11.3.2.4 slecontrolrequestresulttype read-only
The time stamp of the last command (end of command).
               sleArpControlReqResult 1.3.6.1.4.1.6296.101.11.3.2.5 timeticks read-only
The result of the last user command.
               sleArpControlNetIfIndex 1.3.6.1.4.1.6296.101.11.3.2.6 integer32 read-write
Network interface index.
               sleArpControlIpAddress 1.3.6.1.4.1.6296.101.11.3.2.7 ipaddress read-write
The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
               sleArpControlPhyAddress 1.3.6.1.4.1.6296.101.11.3.2.8 macaddress read-write
The media-dependent `physical' address.
               sleArpControlState 1.3.6.1.4.1.6296.101.11.3.2.9 integer read-write
Arp entry's currently status. Enumeration: 'dynamic': 1, 'static': 0.
               sleArpControlMask 1.3.6.1.4.1.6296.101.11.3.2.10 integer read-write
Description.
           sleArpNotification 1.3.6.1.4.1.6296.101.11.3.3
               sleArpEntryCreated 1.3.6.1.4.1.6296.101.11.3.3.1
createArpEntry.
               sleArpEntryDestroyed 1.3.6.1.4.1.6296.101.11.3.3.2
destroyArpEntry.
               sleArpTableCleared 1.3.6.1.4.1.6296.101.11.3.3.3
clearArpTable. In this notification PDU, key of sleArpState is ifindex.0.0.0.0.
               sleArpTableClearedByAddr 1.3.6.1.4.1.6296.101.11.3.3.4
clearArpTableByAddr
       sleRoute 1.3.6.1.4.1.6296.101.11.4
           sleRouteTable 1.3.6.1.4.1.6296.101.11.4.1 no-access
Description.
               sleRouteEntry 1.3.6.1.4.1.6296.101.11.4.1.1 no-access
Description.
                   sleRouteDstAddress 1.3.6.1.4.1.6296.101.11.4.1.1.1 ipaddress read-only
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.
                   sleRouteDstMask 1.3.6.1.4.1.6296.101.11.4.1.1.2 integer read-only
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
                   sleRouteGateway 1.3.6.1.4.1.6296.101.11.4.1.1.3 ipaddress read-only
The Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalid
                   sleRouteInterface 1.3.6.1.4.1.6296.101.11.4.1.1.4 integer read-only
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of sleNetIfIndex. Network interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface index
                   sleRouteType 1.3.6.1.4.1.6296.101.11.4.1.1.5 integer read-write
The type of route. Note that the values direct and indirect refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid has the effect of invalidating the corresponding entry in the sleRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant sleRouteType object. Enumeration: 'indirect': 4, 'other': 1, 'direct': 3, 'invalid': 2.
                   sleRouteProto 1.3.6.1.4.1.6296.101.11.4.1.1.6 integer read-only
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols. Enumeration: 'esIs': 10, 'isIs': 9, 'ggp': 6, 'idpr': 15, 'ciscoEigrp': 16, 'egp': 5, 'rip': 8, 'bgp': 14, 'netmgmtStatic': 3, 'ciscoIgrp': 11, 'other': 1, 'dhcp': 17, 'bbnSpfIgp': 12, 'icmp': 4, 'ospf': 13, 'hello': 7, 'localDirect': 2.
                   sleRouteMetric 1.3.6.1.4.1.6296.101.11.4.1.1.7 integer read-write
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's sleRouteProto value. If this metric is not used, its value should be set to -1.
                   sleRouteActive 1.3.6.1.4.1.6296.101.11.4.1.1.8 integer read-write
The active status for this routing entry. Enumeration: 'active': 1, 'inactive': 0.
                   sleRouteBindingSrcAddr 1.3.6.1.4.1.6296.101.11.4.1.1.9 ipaddress read-only
The binding source IP Address for this route.
                   sleRouteDistance 1.3.6.1.4.1.6296.101.11.4.1.1.10 integer read-write
The Distance value for this route.
                   sleRouteSubtype 1.3.6.1.4.1.6296.101.11.4.1.1.11 integer read-only
The subtype of this route. Enumeration: 'isisL2': 9, 'ospfIa': 1, 'isisL1': 8, 'ospfNssa2': 3, 'unknown': 0, 'ospfNssa1': 2, 'bgpMpls': 11, 'ospfExternal2': 5, 'ospfExternal1': 4, 'isisIa': 10.
                   sleRouteNexthopStatus 1.3.6.1.4.1.6296.101.11.4.1.1.12 bits read-only
The nexthop status of this route. Bits: 'active': 0, 'fib': 1, 'recursive': 2.
                   sleRouteRibStatus 1.3.6.1.4.1.6296.101.11.4.1.1.13 bits read-only
The rib status for this route. Bits: 'changed': 5, 'selected': 4, 'blackhole': 2, 'selfroute': 1, 'internal': 0, 'static': 6, 'nonfib': 3, 'stale': 7.
                   sleRouteVRFIndex 1.3.6.1.4.1.6296.101.11.4.1.1.14 integer32 read-only
VRF index in sleIpVRFTable.
           sleRouteControl 1.3.6.1.4.1.6296.101.11.4.2
               sleRouteControlRequest 1.3.6.1.4.1.6296.101.11.4.2.1 integer read-write
The request of a user command. Enumeration: 'createStaticRoute': 1, 'destroyStaticRoute': 2, 'setStaticRouteProfile': 3.
               sleRouteControlStatus 1.3.6.1.4.1.6296.101.11.4.2.2 slecontrolstatustype read-only
The status of a user command.
               sleRouteControlTimer 1.3.6.1.4.1.6296.101.11.4.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleRouteControlTimeStamp 1.3.6.1.4.1.6296.101.11.4.2.4 slecontrolrequestresulttype read-only
The result of the last user command.
               sleRouteControlReqResult 1.3.6.1.4.1.6296.101.11.4.2.5 timeticks read-only
The time stamp of the last command (end of command).
               sleRouteControlDstAddress 1.3.6.1.4.1.6296.101.11.4.2.6 ipaddress read-write
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.
               sleRouteControlDstMask 1.3.6.1.4.1.6296.101.11.4.2.7 integer read-write
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
               sleRouteControlGateway 1.3.6.1.4.1.6296.101.11.4.2.8 ipaddress read-write
The Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalid
               sleRouteControlInterface 1.3.6.1.4.1.6296.101.11.4.2.9 integer read-write
Network interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface index To config interface, sleRouteControlGateway have to be removed.
               sleRouteControlBindingSrcAddr 1.3.6.1.4.1.6296.101.11.4.2.10 ipaddress read-write
The binding source IP Address for this route.
               sleRouteControlDistance 1.3.6.1.4.1.6296.101.11.4.2.11 integer read-write
The Distance value for this route.
               sleRouteControlVRFIndex 1.3.6.1.4.1.6296.101.11.4.2.12 integer32 read-write
VRF index in sleIpVRFTable.
           sleRouteNotification 1.3.6.1.4.1.6296.101.11.4.3
               sleRouteStaticCreated 1.3.6.1.4.1.6296.101.11.4.3.1
createStaticRoute
               sleRouteStaticDestroyed 1.3.6.1.4.1.6296.101.11.4.3.2
destroyStaticRoute
               sleRouteStaticProfileChanged 1.3.6.1.4.1.6296.101.11.4.3.3
setStaticRouteProfile
       sleDhcpClient 1.3.6.1.4.1.6296.101.11.5
           sleDhcpClTable 1.3.6.1.4.1.6296.101.11.5.1 no-access
Description.
               sleDhcpClEntry 1.3.6.1.4.1.6296.101.11.5.1.1 no-access
Description.
                   sleDhcpClMode 1.3.6.1.4.1.6296.101.11.5.1.1.1 integer read-only
DHCP Client activity state in this interface. Enumeration: 'enable': 1, 'disable': 0.
                   sleDhcpClIpAddr 1.3.6.1.4.1.6296.101.11.5.1.1.2 ipaddress read-only
The IP address acquired by DHCP Client active in this interface.
                   sleDhcpClNetmask 1.3.6.1.4.1.6296.101.11.5.1.1.3 ipaddress read-only
The subnet mask associated with the IP address acquired by DHCP Client. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
                   sleDhcpClGateway 1.3.6.1.4.1.6296.101.11.5.1.1.4 ipaddress read-only
The Gateway's IP address acquired by DHCP Client active in this interface.
                   sleDhcpClDnsServer 1.3.6.1.4.1.6296.101.11.5.1.1.5 ipaddress read-only
The DNS server's IP address acquired by DHCP Client active in this interface.
                   sleDhcpClServer 1.3.6.1.4.1.6296.101.11.5.1.1.6 ipaddress read-only
DHCP Server's IP address.
                   sleDhcpClClientId 1.3.6.1.4.1.6296.101.11.5.1.1.7 octet string read-only
DHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.
                   sleDhcpClClientIdStyle 1.3.6.1.4.1.6296.101.11.5.1.1.8 integer read-only
DHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal format Enumeration: 'hex': 1, 'ascii': 0.
                   sleDhcpClClassId 1.3.6.1.4.1.6296.101.11.5.1.1.9 octet string read-only
DHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.
                   sleDhcpClClassIdStyle 1.3.6.1.4.1.6296.101.11.5.1.1.10 integer read-only
DHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal format Enumeration: 'hex': 1, 'ascii': 0.
                   sleDhcpClLeasetime 1.3.6.1.4.1.6296.101.11.5.1.1.11 integer32 read-only
The leased time for IP address acquired by DHCP Client. Default lease-time: 3600s
                   sleDhcpClState 1.3.6.1.4.1.6296.101.11.5.1.1.12 integer read-only
The operating status of DHCP Client. Enumeration: 'halt': 0, 'request': 3, 'init': 1, 'bound': 4, 'rebind': 6, 'renew': 5, 'nonactive': 255.
           sleDhcpClControl 1.3.6.1.4.1.6296.101.11.5.2
               sleDhcpClControlRequest 1.3.6.1.4.1.6296.101.11.5.2.1 integer read-write
The request of a user command. Enumeration: 'setDhcpClMode': 1, 'changeDhcpClState': 3, 'setDhcpClProfile': 2.
               sleDhcpClControlStatus 1.3.6.1.4.1.6296.101.11.5.2.2 slecontrolstatustype read-only
The status of a user command.
               sleDhcpClControlTimer 1.3.6.1.4.1.6296.101.11.5.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleDhcpClControlTimeStamp 1.3.6.1.4.1.6296.101.11.5.2.4 slecontrolrequestresulttype read-only
The time stamp of the last command (end of command).
               sleDhcpClControlReqResult 1.3.6.1.4.1.6296.101.11.5.2.5 timeticks read-only
The result of the last user command.
               sleDhcpClControlNetIfIndex 1.3.6.1.4.1.6296.101.11.5.2.6 integer32 read-write
Network Interface Index.
               sleDhcpClControlMode 1.3.6.1.4.1.6296.101.11.5.2.7 integer read-write
DHCP Client activity state in this interface. Enumeration: 'enable': 1, 'disable': 0.
               sleDhcpClControlClientId 1.3.6.1.4.1.6296.101.11.5.2.8 octet string read-write
DHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.
               sleDhcpClControlClientIdStyle 1.3.6.1.4.1.6296.101.11.5.2.9 integer read-write
DHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal format Enumeration: 'hex': 1, 'ascii': 0.
               sleDhcpClControlClassId 1.3.6.1.4.1.6296.101.11.5.2.10 octet string read-write
DHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.
               sleDhcpClControlClassIdStyle 1.3.6.1.4.1.6296.101.11.5.2.11 integer read-write
DHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal format Enumeration: 'hex': 1, 'ascii': 0.
               sleDhcpClControlLeasetime 1.3.6.1.4.1.6296.101.11.5.2.12 integer32 read-write
The leased time for IP address acquired by DHCP Client. Default lease-time: 3600s
               sleDhcpClControlUpdateIP 1.3.6.1.4.1.6296.101.11.5.2.13 integer read-write
Update DHCP client operating status. 0 : default 1 : renew 2 : release Enumeration: 'release': 2, 'remain': 0, 'renew': 1.
           sleDhcpClNotification 1.3.6.1.4.1.6296.101.11.5.3
               sleDhcpClModeChanged 1.3.6.1.4.1.6296.101.11.5.3.1
setDhcpClMode.
               sleDhcpClProfileChanged 1.3.6.1.4.1.6296.101.11.5.3.2
setDhcpClProfile.
               sleDhcpClStateChanged 1.3.6.1.4.1.6296.101.11.5.3.3
ChangeDhcpClState.
       sleV2DhcpClient 1.3.6.1.4.1.6296.101.11.6
       sleNetworkBase 1.3.6.1.4.1.6296.101.11.7
           sleNetworkBaseInfo 1.3.6.1.4.1.6296.101.11.7.1
               sleNetworkArpAgingTime 1.3.6.1.4.1.6296.101.11.7.1.1 integer read-only
System Arp Aging Time
               sleNetworkBaseVrfDynamicForwardBinding 1.3.6.1.4.1.6296.101.11.7.1.2 integer read-only
Description. Enumeration: 'vrrp': 1, 'disable': 0.
           sleNetworkBaseControl 1.3.6.1.4.1.6296.101.11.7.2
               sleNetworkControlRequest 1.3.6.1.4.1.6296.101.11.7.2.1 integer read-write
Description. Enumeration: 'setVrfForwdDynamicStatus': 2, 'setArpProfile': 1.
               sleNetworkControlStatus 1.3.6.1.4.1.6296.101.11.7.2.2 slecontrolstatustype read-only
Description.
               sleNetworkControlTimer 1.3.6.1.4.1.6296.101.11.7.2.3 gauge32 read-write
Description.
               sleNetworkControlTimeStamp 1.3.6.1.4.1.6296.101.11.7.2.4 timeticks read-only
Description.
               sleNetworkControlReqResult 1.3.6.1.4.1.6296.101.11.7.2.5 slecontrolrequestresulttype read-only
Description.
               sleNetworkControlArpAgingTime 1.3.6.1.4.1.6296.101.11.7.2.6 integer read-write
Description.
               sleNetworkControlVrfDynamicForwardBinding 1.3.6.1.4.1.6296.101.11.7.2.7 integer read-write
Description. Enumeration: 'vrrp': 1, 'disable': 0.
           sleNetworkBaseNotification 1.3.6.1.4.1.6296.101.11.7.3
               sleNetworkArpProfileChanged 1.3.6.1.4.1.6296.101.11.7.3.1
Description.
       sleTunnel 1.3.6.1.4.1.6296.101.11.8
           sleTunnelIfTable 1.3.6.1.4.1.6296.101.11.8.1 no-access
Description.
               sleTunnelIfEntry 1.3.6.1.4.1.6296.101.11.8.1.1 no-access
Description.
                   sleTunnelIfIndex 1.3.6.1.4.1.6296.101.11.8.1.1.1 integer32 read-only
Tunnel interface index
                   sleTunnelIfLocalAddress 1.3.6.1.4.1.6296.101.11.8.1.1.2 ipaddress read-only
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.
                   sleTunnelIfRemoteAddress 1.3.6.1.4.1.6296.101.11.8.1.1.3 ipaddress read-only
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.
                   sleTunnelIfMode 1.3.6.1.4.1.6296.101.11.8.1.1.4 ianatunneltype read-only
The encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulation
                   sleTunnelIfTTL 1.3.6.1.4.1.6296.101.11.8.1.1.5 integer32 read-only
The TTL to use in the outer IP header.
                   sleTunnelIfDscpMode 1.3.6.1.4.1.6296.101.11.8.1.1.6 integer read-only
The DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value. Enumeration: 'dscpMapFromPacket': 3, 'dscpCopyFromPacket': 2, 'dscpAssign': 1.
                   sleTunnelIfDscp 1.3.6.1.4.1.6296.101.11.8.1.1.7 integer32 read-only
The static DiffServ field value to use in the outer IP header.
                   sleTunnelIfKeepaliveInterval 1.3.6.1.4.1.6296.101.11.8.1.1.8 integer32 read-only
Specifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)
                   sleTunnelIfKeepaliveRetry 1.3.6.1.4.1.6296.101.11.8.1.1.9 integer32 read-only
Specifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)
                   sleTunnelIfPathMtuDiscovery 1.3.6.1.4.1.6296.101.11.8.1.1.10 integer read-only
Path mtu discovery on tunnel. Enumeration: 'enable': 1, 'disable': 2.
                   sleTunnelIfVRFName 1.3.6.1.4.1.6296.101.11.8.1.1.11 octet string read-only
VPN Routing/Forwarding instance name.
                   sleTunnelIfBindingPorts 1.3.6.1.4.1.6296.101.11.8.1.1.12 octet string read-only
Tunnel binding ports map.
                   sleTunnelIfLocalAddress6 1.3.6.1.4.1.6296.101.11.8.1.1.13 inetaddress read-only
The address of the local endpoint of the tunnel for IPv6
                   sleTunnelIfRemoteAddress6 1.3.6.1.4.1.6296.101.11.8.1.1.14 inetaddress read-only
The address of the remote endpoint of the tunnel for IPv6
                   sleTunnelIfChecksum 1.3.6.1.4.1.6296.101.11.8.1.1.15 integer read-only
A checksum feature for the tunnel. Enumeration: 'enable': 1, 'disable': 0.
                   sleTunnelIfDmac 1.3.6.1.4.1.6296.101.11.8.1.1.16 macaddress read-only
A destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)
                   sleTunnelIfTos 1.3.6.1.4.1.6296.101.11.8.1.1.17 integer read-only
A value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.
           sleTunnelIfControl 1.3.6.1.4.1.6296.101.11.8.2
               sleTunnelIfControlRequest 1.3.6.1.4.1.6296.101.11.8.2.1 integer read-write
The request of a user command. Enumeration: 'setTunnelTos': 16, 'createTunnelInterface': 1, 'setTunnelLocalAddr6': 12, 'unsetTunnelIfVRFName': 11, 'setTunnelChecksum': 14, 'setTunnelRemoteAddr6': 13, 'setTunnelIfVRFName': 10, 'setTunnelIfPathMtuDiscovery': 9, 'deleteTunnelInterface': 2, 'setTunnelIfDscp': 7, 'setTunnelIfKeepalive': 8, 'setTunnelIfMode': 5, 'setTunnelDmac': 15, 'setTunnelIfLocalAddress': 3, 'setTunnelIfRemoteAddress': 4, 'setTunnelIfTTL': 6.
               sleTunnelIfControlStatus 1.3.6.1.4.1.6296.101.11.8.2.2 slecontrolstatustype read-only
The status of a user command.
               sleTunnelIfControlTimer 1.3.6.1.4.1.6296.101.11.8.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleTunnelIfControlTimeStamp 1.3.6.1.4.1.6296.101.11.8.2.4 slecontrolrequestresulttype read-only
The result of the last user command.
               sleTunnelIfControlReqResult 1.3.6.1.4.1.6296.101.11.8.2.5 timeticks read-only
The time stamp of the last command (end of command).
               sleTunnelIfControlIndex 1.3.6.1.4.1.6296.101.11.8.2.6 integer32 read-write
Tunnel interface index
               sleTunnelIfControlLocalAddress 1.3.6.1.4.1.6296.101.11.8.2.7 ipaddress read-write
The address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.
               sleTunnelIfControlRemoteAddress 1.3.6.1.4.1.6296.101.11.8.2.8 ipaddress read-write
The address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.
               sleTunnelIfControlMode 1.3.6.1.4.1.6296.101.11.8.2.9 ianatunneltype read-write
The encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulation
               sleTunnelIfControlTTL 1.3.6.1.4.1.6296.101.11.8.2.10 integer32 read-write
The TTL to use in the outer IP header.
               sleTunneIflControlDscpMode 1.3.6.1.4.1.6296.101.11.8.2.11 integer read-write
The DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value. Enumeration: 'dscpMapFromPacket': 3, 'dscpCopyFromPacket': 2, 'dscpAssign': 1.
               sleTunneIflControlDscp 1.3.6.1.4.1.6296.101.11.8.2.12 integer32 read-write
The static DiffServ field value to use in the outer IP header.
               sleTunnelIfControlKeepaliveInterval 1.3.6.1.4.1.6296.101.11.8.2.13 integer32 read-write
Specifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)
               sleTunneIflControlKeepaliveRetry 1.3.6.1.4.1.6296.101.11.8.2.14 integer32 read-write
Specifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)
               sleTunnelIfControlPathMtuDiscovery 1.3.6.1.4.1.6296.101.11.8.2.15 integer read-write
Path mtu discovery on tunnel. Enumeration: 'enable': 1, 'disable': 2.
               sleTunnelIfControlVRFName 1.3.6.1.4.1.6296.101.11.8.2.16 octet string read-write
VPN Routing/Forwarding instance name.
               sleTunnelIfControlLocalAddress6 1.3.6.1.4.1.6296.101.11.8.2.17 inetaddress read-write
The address of the local endpoint of the tunnel for IPv6
               sleTunnelIfControlRemoteAddress6 1.3.6.1.4.1.6296.101.11.8.2.18 inetaddress read-write
The address of the remote endpoint of the tunnel for IPv6
               sleTunnelIfControlChecksum 1.3.6.1.4.1.6296.101.11.8.2.19 integer read-write
A checksum feature for the tunnel. Enumeration: 'enable': 1, 'disable': 0.
               sleTunnelIfControlDmac 1.3.6.1.4.1.6296.101.11.8.2.20 macaddress read-write
A destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)
               sleTunnelIfControlTos 1.3.6.1.4.1.6296.101.11.8.2.21 integer read-write
A value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.
           sleTunnelIfNotification 1.3.6.1.4.1.6296.101.11.8.3
               sleTunnelIfCreated 1.3.6.1.4.1.6296.101.11.8.3.1
Description.
               sleTunnelIfDeleted 1.3.6.1.4.1.6296.101.11.8.3.2
Description.
               sleTunnelIfLocalAddressChanged 1.3.6.1.4.1.6296.101.11.8.3.3
Description.
               sleTunnelIfRemoteAddressChanged 1.3.6.1.4.1.6296.101.11.8.3.4
Description.
               sleTunnelIfModeChanged 1.3.6.1.4.1.6296.101.11.8.3.5
Description.
               sleTunnelIfTTLChanged 1.3.6.1.4.1.6296.101.11.8.3.6
Description.
               sleTunnelIfDscpChanged 1.3.6.1.4.1.6296.101.11.8.3.7
Description.
               sleTunnelIfKeepaliveChanged 1.3.6.1.4.1.6296.101.11.8.3.8
Description.
               sleTunnelIfPathMtuDiscoveryChanged 1.3.6.1.4.1.6296.101.11.8.3.9
Description.
               sleTunnelIfVRFNameSet 1.3.6.1.4.1.6296.101.11.8.3.10
Description.
               sleTunnelIfVRFNameUnset 1.3.6.1.4.1.6296.101.11.8.3.11
Description.
               sleTunnelIfLocalAddress6Changed 1.3.6.1.4.1.6296.101.11.8.3.12
setTunnelLocalAddr6
               sleTunnelIfRemoteAddress6Changed 1.3.6.1.4.1.6296.101.11.8.3.13
setTunnelRemoteAddr6
           sleTunnelAddressTable 1.3.6.1.4.1.6296.101.11.8.4 no-access
Description.
               sleTunnelAddressEntry 1.3.6.1.4.1.6296.101.11.8.4.1 no-access
Description.
                   sleTunnelAddressValue 1.3.6.1.4.1.6296.101.11.8.4.1.1 ipaddress read-only
The IP address to which this entry's addressing information pertains.
                   sleTunnelAddressMask 1.3.6.1.4.1.6296.101.11.8.4.1.2 integer32 read-only
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
                   sleTunnelIpAddrBcast 1.3.6.1.4.1.6296.101.11.8.4.1.3 ipaddress read-only
Description.
                   sleTunnelAddressFlag 1.3.6.1.4.1.6296.101.11.8.4.1.4 bits read-only
dynamic: ~ permanent primary : ~ secondary anycast: this bit is available for ipv6 only. The others are available for ipv4 only. Bits: 'tentative': 1, 'deprecated': 2, 'permanent': 0, 'anycast': 3, 'secondary': 7, 'reserved1': 4, 'reserved3': 6, 'reserved2': 5.
                   sleTunnelAddressScope 1.3.6.1.4.1.6296.101.11.8.4.1.5 integer32 read-only
default : global In linux, 200 - site 0 - global 1..252 - scopeNUM 253 - link 254 - host 255 - nowhere
                   sleTunnelAddressUnnumIfIndex 1.3.6.1.4.1.6296.101.11.8.4.1.6 integer read-only
The unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)
                   sleTunnelAddressUnnumIpIndex 1.3.6.1.4.1.6296.101.11.8.4.1.7 integer read-only
The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
           sleTunnelAddressControl 1.3.6.1.4.1.6296.101.11.8.5
               sleTunnelAddressControlRequest 1.3.6.1.4.1.6296.101.11.8.5.1 integer read-write
The request of a user command. Enumeration: 'createTunnelIpAddress': 1, 'setIfUnnumbered': 3, 'delIfUnnumbered': 4, 'destroyTunnelIpAddress': 2.
               sleTunnelAddressControlStatus 1.3.6.1.4.1.6296.101.11.8.5.2 slecontrolstatustype read-only
The status of a user command.
               sleTunnelAddressControlTimer 1.3.6.1.4.1.6296.101.11.8.5.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleTunnelAddressControlTimeStamp 1.3.6.1.4.1.6296.101.11.8.5.4 slecontrolrequestresulttype read-only
The result of the last user command.
               sleTunnelAddressControlReqResult 1.3.6.1.4.1.6296.101.11.8.5.5 timeticks read-only
The time stamp of the last command (end of command).
               sleTunnelAddressControlTunnelIfIndex 1.3.6.1.4.1.6296.101.11.8.5.6 integer32 read-write
Tunnel interface index
               sleTunnelAddressControlValue 1.3.6.1.4.1.6296.101.11.8.5.7 ipaddress read-write
The IP address to which this entry's addressing information pertains.
               sleTunnelAddressControlMask 1.3.6.1.4.1.6296.101.11.8.5.8 integer32 read-write
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
               sleTunnelAddressControlFlag 1.3.6.1.4.1.6296.101.11.8.5.9 integer read-write
default : primary Enumeration: 'unicast': 4, 'anycast': 3, 'primary': 1, 'secondary': 2.
               sleTunnelAddressControlScope 1.3.6.1.4.1.6296.101.11.8.5.10 integer read-write
default : global not applicable : nowhere Enumeration: 'host': 254, 'global': 0, 'link': 253.
               sleTunnelAddressControlUnnumIfIndex 1.3.6.1.4.1.6296.101.11.8.5.11 integer read-write
The unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)
               sleTunnelAddressControlUnnumIpIndex 1.3.6.1.4.1.6296.101.11.8.5.12 integer read-write
The Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)
           sleTunnelAddressNotification 1.3.6.1.4.1.6296.101.11.8.6
               sleTunnelAddressCreated 1.3.6.1.4.1.6296.101.11.8.6.1
Description.
               sleTunnelAddressDeleted 1.3.6.1.4.1.6296.101.11.8.6.2
Description.
               sleTunnelAddressUnnumChanged 1.3.6.1.4.1.6296.101.11.8.6.3
setIfUnnumbered
               sleTunnelAddressUnnumDeleted 1.3.6.1.4.1.6296.101.11.8.6.4
delIfUnnumbered
       sleIpVRF 1.3.6.1.4.1.6296.101.11.9
           sleIpVRFTable 1.3.6.1.4.1.6296.101.11.9.1 no-access
Description.
               sleIpVRFEntry 1.3.6.1.4.1.6296.101.11.9.1.1 no-access
Description.
                   sleIpVRFIndex 1.3.6.1.4.1.6296.101.11.9.1.1.1 integer32 read-only
VRF index.
                   sleIpVRFName 1.3.6.1.4.1.6296.101.11.9.1.1.2 octet string read-only
VRF name.
                   sleIpVRFDesignatedPorts 1.3.6.1.4.1.6296.101.11.9.1.1.3 octet string read-only
The port map of VRF designated-port.
                   sleIpVRFRouterId 1.3.6.1.4.1.6296.101.11.9.1.1.4 ipaddress read-only
Router-Identifier
                   sleIpVRFDescription 1.3.6.1.4.1.6296.101.11.9.1.1.5 octet string read-only
The description of VRF.
           sleIpVRFControl 1.3.6.1.4.1.6296.101.11.9.2
               sleIpVRFControlRequest 1.3.6.1.4.1.6296.101.11.9.2.1 integer read-write
The request of a user command. Enumeration: 'setIpVRFDesignatedPorts': 3, 'deleteIpVRF': 2, 'createIpVRF': 1, 'setVRFDescription': 6, 'unsetIpVRFDesignatedPorts': 4, 'setVRFRouterId': 5.
               sleIpVRFControlStatus 1.3.6.1.4.1.6296.101.11.9.2.2 slecontrolstatustype read-only
The status of a user command.
               sleIpVRFControlTimer 1.3.6.1.4.1.6296.101.11.9.2.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleIpVRFControlTimeStamp 1.3.6.1.4.1.6296.101.11.9.2.4 slecontrolrequestresulttype read-only
The result of the last user command.
               sleIpVRFControlReqResult 1.3.6.1.4.1.6296.101.11.9.2.5 timeticks read-only
The time stamp of the last command (end of command).
               sleIpVRFControlName 1.3.6.1.4.1.6296.101.11.9.2.6 octet string read-write
VRF name
               sleIpVRFControlDesignatedPorts 1.3.6.1.4.1.6296.101.11.9.2.7 octet string read-write
The port map of VRF designated-port.
               sleIpVRFControlRouterId 1.3.6.1.4.1.6296.101.11.9.2.8 ipaddress read-write
Router-Identifier
               sleIpVRFControlDescription 1.3.6.1.4.1.6296.101.11.9.2.9 octet string read-write
The description of VRF.
           sleIpVRFNotification 1.3.6.1.4.1.6296.101.11.9.3
               sleIpVRFCreated 1.3.6.1.4.1.6296.101.11.9.3.1
Description.
               sleIpVRFDeleted 1.3.6.1.4.1.6296.101.11.9.3.2
Description.
               sleIpVRFDesignatedPortsSet 1.3.6.1.4.1.6296.101.11.9.3.3
Description.
               sleIpVRFDesignatedPortsUnset 1.3.6.1.4.1.6296.101.11.9.3.4
Description.
               sleIpVRFRouterIdChanged 1.3.6.1.4.1.6296.101.11.9.3.5
Description.
               sleIpVRFDescriptionChanged 1.3.6.1.4.1.6296.101.11.9.3.6
Description.
           sleIpVRFSelectionSourceTable 1.3.6.1.4.1.6296.101.11.9.4 no-access
Description.
               sleIpVRFSelectionSourceEntry 1.3.6.1.4.1.6296.101.11.9.4.1 no-access
Description.
                   sleIpVRFSelectionSrcIndex 1.3.6.1.4.1.6296.101.11.9.4.1.1 integer read-only
VRF selection source index.
                   sleIpVRFSelectionSrcAddr 1.3.6.1.4.1.6296.101.11.9.4.1.2 ipaddress read-only
VRF selection by source IP address.
                   sleIpVRFSelectionSrcMask 1.3.6.1.4.1.6296.101.11.9.4.1.3 integer32 read-only
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
                   sleIpVRFSelectionSrcVRFName 1.3.6.1.4.1.6296.101.11.9.4.1.4 octet string read-only
VPN Routing/Forwarding instance name.
           sleIpVRFSelectionSourceControl 1.3.6.1.4.1.6296.101.11.9.5
               sleIpVRFSelectionSrcControlRequest 1.3.6.1.4.1.6296.101.11.9.5.1 integer read-write
The request of a user command. Enumeration: 'unsetVRFSelectionSource': 2, 'setVRFSelectionSource': 1.
               sleIpVRFSelectionSrcControlStatus 1.3.6.1.4.1.6296.101.11.9.5.2 slecontrolstatustype read-only
The status of a user command.
               sleIpVRFSelectionSrcControlTimer 1.3.6.1.4.1.6296.101.11.9.5.3 gauge32 read-write
The maximum wait time for the manager for a long running user command.
               sleIpVRFSelectionSrcControlTimeStamp 1.3.6.1.4.1.6296.101.11.9.5.4 slecontrolrequestresulttype read-only
The result of the last user command.
               sleIpVRFSelectionSrcControlReqResult 1.3.6.1.4.1.6296.101.11.9.5.5 timeticks read-only
The time stamp of the last command (end of command).
               sleIpVRFSelectionSrcControlAddr 1.3.6.1.4.1.6296.101.11.9.5.6 ipaddress read-write
VRF selection by source IP address.
               sleIpVRFSelectionSrcControlMask 1.3.6.1.4.1.6296.101.11.9.5.7 integer32 read-write
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
               sleIpVRFSelectionSrcControlVRFName 1.3.6.1.4.1.6296.101.11.9.5.8 octet string read-write
VPN Routing/Forwarding instance name.
           sleIpVRFSelectionSourceNotification 1.3.6.1.4.1.6296.101.11.9.6
               sleIpVRFSelectionSrcSet 1.3.6.1.4.1.6296.101.11.9.6.1
Description.
               sleIpVRFSelectionSrcUnset 1.3.6.1.4.1.6296.101.11.9.6.2
Description.
       sleBFD 1.3.6.1.4.1.6296.101.11.10
             sleBFDBase 1.3.6.1.4.1.6296.101.11.10.1
                 sleBFDBaseInfo 1.3.6.1.4.1.6296.101.11.10.1.1
                     sleBFDEnable 1.3.6.1.4.1.6296.101.11.10.1.1.1 integer read-only
BFD fast-detect is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.
                     sleBFDEchoEnable 1.3.6.1.4.1.6296.101.11.10.1.1.2 integer read-only
BFD Echo function is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.
                     sleBFDSlowTimer 1.3.6.1.4.1.6296.101.11.10.1.1.3 integer read-only
BFD Slow Timer in unit of milliseconds default: 1000(ms)
                 sleBFDBaseControl 1.3.6.1.4.1.6296.101.11.10.1.2
                     sleBFDControlRequest 1.3.6.1.4.1.6296.101.11.10.1.2.1 integer read-write
The request of a user command Enumeration: 'setBFDBaseProfile': 1.
                     sleBFDControlStatus 1.3.6.1.4.1.6296.101.11.10.1.2.2 slecontrolstatustype read-only
The status of user command.
                     sleBFDControlTimer 1.3.6.1.4.1.6296.101.11.10.1.2.3 gauge32 read-write
The maximum time for the manager for a long running user command.
                     sleBFDControlTimeStamp 1.3.6.1.4.1.6296.101.11.10.1.2.4 timeticks read-only
The time stamp of the last command(end of command).
                     sleBFDControlReqResult 1.3.6.1.4.1.6296.101.11.10.1.2.5 slecontrolrequestresulttype read-only
The result of the last user command.
                     sleBFDControlEnable 1.3.6.1.4.1.6296.101.11.10.1.2.6 integer read-write
BFD fast-detect is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.
                     sleBFDControlEchoEnable 1.3.6.1.4.1.6296.101.11.10.1.2.7 integer read-write
BFD Echo function is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.
                     sleBFDControlSlowTimer 1.3.6.1.4.1.6296.101.11.10.1.2.8 integer read-write
BFD Slow Timer in unit of milliseconds default: 1000(ms)
                 sleBFDBaseNotification 1.3.6.1.4.1.6296.101.11.10.1.3
                     sleBFDBaseProfileChanged 1.3.6.1.4.1.6296.101.11.10.1.3.1
Description.
             sleBFDInterface 1.3.6.1.4.1.6296.101.11.10.2
                 sleBFDInterfaceTable 1.3.6.1.4.1.6296.101.11.10.2.1 no-access
Description.
                     sleBFDInterfaceEntry 1.3.6.1.4.1.6296.101.11.10.2.1.1 no-access
Description.
                         sleBFDIfRxInterval 1.3.6.1.4.1.6296.101.11.10.2.1.1.1 integer read-only
Required Min Rx Interval of BFD control packet in this interface. default: 50(ms)
                         sleBFDIfTxInterval 1.3.6.1.4.1.6296.101.11.10.2.1.1.2 integer read-only
Required Min Tx Interval of BFD control packet in this interface. default: 50(ms)
                         sleBFDIfDetectMulti 1.3.6.1.4.1.6296.101.11.10.2.1.1.3 integer read-only
Detect Multi value of BFD control packet in this interface. default: 3
                         sleBFDIfRxIntervalIPv6 1.3.6.1.4.1.6296.101.11.10.2.1.1.4 integer32 read-only
Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
                         sleBFDIfTxIntervalIJPv6 1.3.6.1.4.1.6296.101.11.10.2.1.1.5 integer32 read-only
Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
                         sleBFDIfDetectMultiIPv6 1.3.6.1.4.1.6296.101.11.10.2.1.1.6 integer32 read-only
Detect Multi value of IPv6 BFD control packet in this interface. default: 3
                 sleBFDInterfaceControl 1.3.6.1.4.1.6296.101.11.10.2.2
                     sleBFDIfControlRequest 1.3.6.1.4.1.6296.101.11.10.2.2.1 integer read-write
The request of a user command Enumeration: 'setBFDIfProfile': 1.
                     sleBFDIfControlStatus 1.3.6.1.4.1.6296.101.11.10.2.2.2 slecontrolstatustype read-only
The status of user command.
                     sleBFDIfControlTimer 1.3.6.1.4.1.6296.101.11.10.2.2.3 gauge32 read-write
The maximum time for the manager for a long running user command.
                     sleBFDIfControlTimeStamp 1.3.6.1.4.1.6296.101.11.10.2.2.4 timeticks read-only
The time stamp of the last command(end of command).
                     sleBFDIfControlReqResult 1.3.6.1.4.1.6296.101.11.10.2.2.5 slecontrolrequestresulttype read-only
The result of the last user command.
                     sleBFDIfControlNetIfIndex 1.3.6.1.4.1.6296.101.11.10.2.2.6 integer32 read-write
BFD Interface Index.
                     sleBFDIfControlRxInterval 1.3.6.1.4.1.6296.101.11.10.2.2.7 integer read-write
Required Min Rx Interval of BFD control packet in this interface. default: 50(ms)
                     sleBFDIfControlTxInterval 1.3.6.1.4.1.6296.101.11.10.2.2.8 integer read-write
Required Min Tx Interval of BFD control packet in this interface. default: 50(ms)
                     sleBFDIfControlDetectMulti 1.3.6.1.4.1.6296.101.11.10.2.2.9 integer read-write
Detect Multi value of BFD control packet in this interface. default: 3
                     sleBFDIfControlRxIntervalIPv6 1.3.6.1.4.1.6296.101.11.10.2.2.10 integer32 read-write
Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
                     sleBFDIfControlTxIntervalIPv6 1.3.6.1.4.1.6296.101.11.10.2.2.11 integer32 read-write
Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)
                     sleBFDIfControlDetectMultiIPv6 1.3.6.1.4.1.6296.101.11.10.2.2.12 integer32 read-write
Detect Multi value of IPv6 BFD control packet in this interface. default: 3
                 sleBFDInterfaceNotification 1.3.6.1.4.1.6296.101.11.10.2.3
                     sleBFDIfProfileChanged 1.3.6.1.4.1.6296.101.11.10.2.3.1
Description.
             sleBFDSession 1.3.6.1.4.1.6296.101.11.10.3
                 sleBFDSessionInfo 1.3.6.1.4.1.6296.101.11.10.3.1
                     sleBFDSessionInfoTable 1.3.6.1.4.1.6296.101.11.10.3.1.1 no-access
Description.
                         sleBFDSessionInfoEntry 1.3.6.1.4.1.6296.101.11.10.3.1.1.1 no-access
Description.
                             sleBFDSessionNeighAddrType 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.1 inetaddresstype read-only
Type of Neighbor Address referred to this session
                             sleBFDSessionNeighAddrValue 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.2 inetaddress read-only
Value of Neighbor Address referred to this session.
                             sleBFDSessionRegProtocols 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.3 bits read-only
Value of Neighbor Address referred to this session. Bits: 'ospfv2': 0, 'ospfv3': 1, 'bgp': 6, 'vrrp6': 3, 'vrrp4': 2, 'staticroute6': 5, 'staticroute4': 4.
                             sleBFDSessionLocalDiscr 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.4 unsigned32 read-only
Discriminator of this session.
                             sleBFDSessionRemoteDiscr 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.5 unsigned32 read-only
Discriminator of remote session neighboring this session.
                             sleBFDSessionDetecMultiplier 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.6 integer read-only
Detect Multiplier value which this session used. default: 3
                             sleBFDSessionStatus 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.7 integer read-only
Status of this session. AdminDown(0) is same as disabled(4). Enumeration: 'adminDown': 0, 'down': 1, 'init': 2, 'up': 3, 'disabled': 4.
                             sleBFDSessionEchoUsage 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.8 integer read-only
Determine whether this session use or not echo function. Enumeration: 'notUsing': 0, 'using': 1.
                             sleBFDSessionUptime 1.3.6.1.4.1.6296.101.11.10.3.1.1.1.9 timeticks read-only
The time since this sessions status changed into Up.
                 sleBFDSessionStats 1.3.6.1.4.1.6296.101.11.10.3.2
                     sleBFDSessionStatsTable 1.3.6.1.4.1.6296.101.11.10.3.2.1 no-access
Description.
                         sleBFDSessionStatsEntry 1.3.6.1.4.1.6296.101.11.10.3.2.1.1 no-access
Description.
                             sleBFDSessionStatsHolddownTime 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.1 unsigned32 read-only
Type of Neighbor Address referred to this session.
                             sleBFDSessionStatsHolddownExpires 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.2 unsigned32 read-only
The time remaining before this entry change into down status without receiving hello in unit of milliseconds.
                             sleBFDSessionStatsHolddownHitCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.3 unsigned32 read-only
Hit Count whose this session status chang into down.
                             sleBFDSessionStatsHelloTime 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.4 unsigned32 read-only
The time is when it expects next hello, after receiving that in unit of milliseconds.
                             sleBFDSessionStatsHelloHitCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.5 unsigned32 read-only
Hit Count whose this session received.
                             sleBFDSessionStatsRxCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.6 unsigned32 read-only
Hit Count whose this session received control packet.
                             sleBFDSessionStatsRxAvgInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.7 unsigned32 read-only
Average interval whose this session received control packet.
                             sleBFDSessionStatsRxMinInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.8 unsigned32 read-only
Minimum interval whose this session received control packet.
                             sleBFDSessionStatsRxMaxInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.9 unsigned32 read-only
Maximum interval whose this session received control packet.
                             sleBFDSessionStatsTxCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.10 unsigned32 read-only
Hit Count whose this session send control packet.
                             sleBFDSessionStatsTxAvgInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.11 unsigned32 read-only
Average interval whose this session sent control packet.
                             sleBFDSessionStatsTxMinInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.12 unsigned32 read-only
Minimum interval whose this session sent control packet.
                             sleBFDSessionStatsTxMaxInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.13 unsigned32 read-only
Maximum interval whose this session received control packet.
                             sleBFDSessionStatsEchoRxCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.14 unsigned32 read-only
Hit Count whose this session received echo packet
                             sleBFDSessionStatsEchoRxAvgInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.15 unsigned32 read-only
Average interval whose this session received echo packet
                             sleBFDSessionStatsEchoRxMinInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.16 unsigned32 read-only
Minimum interval whose this session received echo packet
                             sleBFDSessionStatsEchoRxMaxInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.17 unsigned32 read-only
Maximum interval whose this session received echo packet
                             sleBFDSessionStatsEchoTxCount 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.18 unsigned32 read-only
Hit Count whose this session send echo packet
                             sleBFDSessionStatsEchoTxAvgInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.19 unsigned32 read-only
Average interval whose this session sent echo packet.
                             sleBFDSessionStatsEchoTxMinInterva 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.20 unsigned32 read-only
Minimum interval whose this session sent echo packet.
                             sleBFDSessionStatsEchoTxMaxInterval 1.3.6.1.4.1.6296.101.11.10.3.2.1.1.21 unsigned32 read-only
Maximum interval whose this session received echo packet.
                 sleBFDSessionLocal 1.3.6.1.4.1.6296.101.11.10.3.3
                     sleBFDSessionLocalTable 1.3.6.1.4.1.6296.101.11.10.3.3.1 no-access
Description.
                         sleBFDSessionLocalEntry 1.3.6.1.4.1.6296.101.11.10.3.3.1.1 no-access
Description.
                             sleBFDSessionLocalDiag 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.1 integer read-only
Value of State field of this sessions control packet. Enumeration: 'detectExpired': 1, 'reserved': 9, 'adminDown': 7, 'fwdPlaneReset': 4, 'neighDownAlarm': 3, 'reverseConcatDown': 8, 'concatPathDown': 6, 'pathDown': 5, 'echoFailed': 2, 'noDiag': 0.
                             sleBFDSessionLocalState 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.2 integer read-only
Value of Diag field of this sessions control packet Enumeration: 'adminDown': 0, 'init': 2, 'up': 3, 'donw': 1.
                             sleBFDSessionLocalFlags 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.3 bits read-only
Value of Flags field of this sessions control packet. Bits: 'multipoint': 5, 'authPresent': 3, 'controlIndependent': 2, 'demand': 4, 'poll': 0, 'final': 1.
                             sleBFDSessionLocalMultiplier 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.4 integer read-only
Value of MinTxInterval field of this sessions control packet in unit of microseconds.
                             sleBFDSessionLocalMinTxInterval 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.5 unsigned32 read-only
Value of MinTxInterval field of this sessions control packet in unit of microseconds.
                             sleBFDSessionLocalMinRxInterval 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.6 unsigned32 read-only
Value of MinRxInterval field of this sessions control packet in unit of microseconds.
                             sleBFDSessionLocalMinEchoInterval 1.3.6.1.4.1.6296.101.11.10.3.3.1.1.7 unsigned32 read-only
Value of MinEchoInterval field of this sessions control packet in unit of microseconds.
                 sleBFDSessionRemote 1.3.6.1.4.1.6296.101.11.10.3.4
                     sleBFDSessionRemoteTable 1.3.6.1.4.1.6296.101.11.10.3.4.1 no-access
Description.
                         sleBFDSessionRemoteEntry 1.3.6.1.4.1.6296.101.11.10.3.4.1.1 no-access
Description.
                             sleBFDSessionRemoteDiag 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.1 integer read-only
Value of State field of remote sessions control packet. Enumeration: 'detectExpired': 1, 'reserved': 9, 'adminDown': 7, 'fwdPlaneReset': 4, 'neighDownAlarm': 3, 'reverseConcatDown': 8, 'concatPathDown': 6, 'pathDown': 5, 'echoFailed': 2, 'noDiag': 0.
                             sleBFDSessionRemoteState 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.2 integer read-only
Value of Diag field of remote sessions control packet Enumeration: 'adminDown': 0, 'init': 2, 'up': 3, 'donw': 1.
                             sleBFDSessionremoteFlags 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.3 bits read-only
Value of Flags field of remote sessions control packet. Bits: 'multipoint': 5, 'authPresent': 3, 'controlIndependent': 2, 'demand': 4, 'poll': 0, 'final': 1.
                             sleBFDSessionRemoteMultiplier 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.4 integer read-only
Value of MinTxInterval field of this sessions control packet in unit of microseconds.
                             sleBFDSessionRemoteMinTxInterval 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.5 unsigned32 read-only
Value of MinTxInterval field of remote sessions control packet in unit of microseconds.
                             sleBFDSessionRemoteMinRxInterval 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.6 unsigned32 read-only
Value of MinRxInterval field of remote sessions control packet in unit of microseconds.
                             sleBFDSessionRemoteMinEchoInterval 1.3.6.1.4.1.6296.101.11.10.3.4.1.1.7 unsigned32 read-only
Value of MinEchoInterval field of remote sessions control packet in unit of microseconds.
             sleBFDStaticGw 1.3.6.1.4.1.6296.101.11.10.4
                 sleBFDStaticGwTable 1.3.6.1.4.1.6296.101.11.10.4.1 no-access
Description.
                     sleBFDStaticGwEntry 1.3.6.1.4.1.6296.101.11.10.4.1.1 no-access
Description.
                         sleBFDStaticGwAddrType 1.3.6.1.4.1.6296.101.11.10.4.1.1.1 inetaddresstype read-write
The BFD static Gateway address type. Only ipv4(1).
                         sleBFDStaticGwAddr 1.3.6.1.4.1.6296.101.11.10.4.1.1.2 inetaddress read-write
The BFD static Gateway address. 4bytes
                 sleBFDStaticGwControl 1.3.6.1.4.1.6296.101.11.10.4.2
                     sleBFDStaticGwControlRequest 1.3.6.1.4.1.6296.101.11.10.4.2.1 integer read-write
Description. Enumeration: 'addBfdStaticGw': 1, 'delBfdStaticGw': 2.
                     sleBFDStaticGwControlStatus 1.3.6.1.4.1.6296.101.11.10.4.2.2 slecontrolstatustype read-only
Description.
                     sleBFDStaticGwControlTimer 1.3.6.1.4.1.6296.101.11.10.4.2.3 gauge32 read-write
Description.
                     sleBFDStaticGwControlTimeStamp 1.3.6.1.4.1.6296.101.11.10.4.2.4 timeticks read-only
Description.
                     sleBFDStaticGwControlReqResult 1.3.6.1.4.1.6296.101.11.10.4.2.5 slecontrolrequestresulttype read-only
Description.
                     sleBFDStaticGwControlNetIfIndex 1.3.6.1.4.1.6296.101.11.10.4.2.6 integer32 read-write
Description.
                     sleBFDStaticGwControlGwAddrType 1.3.6.1.4.1.6296.101.11.10.4.2.7 inetaddresstype read-write
Description.
                     sleBFDStaticGwControlGwAddr 1.3.6.1.4.1.6296.101.11.10.4.2.8 inetaddress read-write
Description.
                 sleBFDStaticGwNotification 1.3.6.1.4.1.6296.101.11.10.4.3
                     sleBFDStaticGwAdded 1.3.6.1.4.1.6296.101.11.10.4.3.1
Description.
                     sleBFDStaticGwDeleted 1.3.6.1.4.1.6296.101.11.10.4.3.2
Description.
       sleNetworkGroup 1.3.6.1.4.1.6296.101.11.14
Description.
       sleNetworkNotificationGroup 1.3.6.1.4.1.6296.101.11.15
Description.