SHE-SHDSL-MIB: View SNMP OID List / Download MIB

This MIB module defines a collection of objects for managing HDSL2/SHDSL lines according RFC3276. An agent may reside at either end of the line, however the MIB is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines). Adapted to support RFC 4319.

This bitmap specifies the transmission modes that the STU-C is capable of supporting. Right now, support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MxU.

This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line status. The table will only be supported for interfaces of iftype sdsl (96)!

An entry (conceptual row) in the dsShdslLineStatusTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)!

This object identifies the high level operational state for the STU.

This object identifies the current detailed operational state of the STU.

Transceiver firmware release number.

This object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only.

This object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA.

This object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object is used to determine if carrier has been lost.

This object identifies the local STU transmit power in tenths of a dBm.

This object returns information regarding the framer synchronization status.

This object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies if the receive clock is in or out of range.

This object provides the total receiver gain in dB.

This object provides the count of bit errors since the last time the object was read, as well as the type of synchronization.

This object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd.

This object provides the transceiver firmware release number of the STU at the other end of the loop.

This object indicates whether cell delineation has been found.

This object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF.

This object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF.

This object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF.

This object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF.

This object returns the customer identification that was sent by the STU at the other end of the loop.

This object returns non-standard format customer data that was sent by the STU at the other end of the loop.

This object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported.

This object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported.

This object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported.

This object provides the transmit power of the STU at the other end of the loop.

This object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop.

This object indicates the number of automatic retrains. This counter is only reset when a startup is initiated.

This object provides status information about the eoc stage.

This object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second.

This object identifies the Network Timing Recovery Fault.

The CPE master Core.

Indicates the Result of the Parametric Test conducted on the Xcvr.

Conexant parameter that indicates the Parametric Test Array.

This conexant parameter indicates the startup mode, whether the lines comes up in bis mode or legacy mode (non bis).

This conexant parameter provides a way to see what rates are supported by the local STU in the form of tuples.

This conexant parameter provides a way to see what rates are supported by the STU at other end of the loop in the form of tuples.

This conexant parametetr provides the results of rates exchanged during handshake in the form of tuples.

This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line parameters. The table will only be supported for interfaces of iftype sdsl (96)!

An entry (conceptual row) in the dsShdslLineParamsTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)!

This object specifies actions that are used to control transceiver operation.

This object specifies the operational mode of the transceiver.

This object is used to compensate for minor differences in transmit power between designs.

This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.

This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2

This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.

This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.

This object defines how network-timing recovery is performed.

Customer-defined value. This object defines the upstream frame sync word.

This object defines the downstream frame sync word.

Customer-defined value. This object defines the upstream.

This object defines the downstream stuff bits.

This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.

This object determines the source of the receive clock.

This object enables or disables the internal PLL.

This object enables the user to set the size of the framer buffer for serial ATM operation.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse.

This object specifies the multi frame operational mode of the transceiver.

This object specifies the operational state of the 4_6Mbps bit rate.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and the STU at the opposite end will remain in handshake.

This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.

This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.

This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.

This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.

This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.

This object specifies the Gear Shift Type.

This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.

This object specifies the maximum bit per baud.

This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.

This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.

This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.

This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.

Enables or disables auto-retrain.

Enables or disables auto-retrain based on CRC errors.

Enables or disables auto-retrain based on framer synchronization.

Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.

Sets the threshold for the number of frames with CRC errors for autoretrain.

Set the margin threshold for autoretrain.

Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.

Enables/disables trap indicating a change in op state.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit clock.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive clock.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).

This object specifies framer OverHead Channel.

This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.

This Parameter enables or disables the Trap for SNR Margin Threshold crossing.

This Parameter enables or disables the Trap for Framer Overhead and Defects.

Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.

Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN.

Indicates End bin for range of bins to be measured. The default value mentioned is an indicative value only.

This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.

This objects defines which AFE is being used.

This object selects the appropriate UTOPIA Level 2 address for the transmit interface.

This object selects the appropriate UTOPIA Level 2 address for the receive interface.

This parameter is used to specify width of UTOPIA data bus.

This parameter is used to configure the PAM mode value for startup.

modifyShdslLineParamsEntry a complete set of configurable parameters according the sheShdlsLinParamsControl-group.

Index of the modified entry.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Look at Table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

This table is a proprietary extension of hdsl2ShdslSpanStatusTable. The table will only be supported for interfaces of iftype sdsl (96)!

An entry (conceptual row) in the dsShdslSpanStatusExtnTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)!

This object provides the maximum PMMS rate the line is capable of achieving

Contains the current 4 Wire Handshake Mode Configured

This table contains a fixed set of possible bondig group entrys. This table will not longer be supported.

This table contains a fixed set of possible bondig group entrys. Index is the ifIndex from if-table (used iftype is 143 - msdsl - multirate sdsl). Entry will be created and deleted during card create or delete for a shdsl-card. For one shdsl card with 48 shdsl lines, this table will contain 24 groups of type twoPortsBondingGroup and 12 entrys of type fourPortsBondingGroup.

Portlist for all member of this bonding group. The octet string is a list of pairs of octets each identify an sheBridgePortIndex. The least significant byte is the second octet.

The type descripes if this group contain 2 or 4 shdsl - lines.

This table supports overall configuration of HDSL2/SHDSL Spans. Entries in this table MUST be maintained in a persistent manner.

An entry in the hdsl2ShdslSpanConfTable. Each entry represents the complete Span in a single SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line.

This object provisions the number of repeaters/regenerators in this HDSL2/SHDSL Span. The System will not support repeaters.

This object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslSpanConfProfileTable, MUST be rejected.

This object is a pointer to an Alarm configuration profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration in the referenced profile will be used by default for all segment endpoints in this span. Individual endpoints may override this profile by explicitly specifying some other profile in the hdsl2ShdslEndpointConfTable. By default, this object will have the value 'DEFVAL' (the index of the default profile). Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected.

modifyshehdsl2ShdslSpanConfEntry shehdsl2ShdslSpanConfControlNumRepeaters shehdsl2ShdslSpanConfControlProfile modifyshehdsl2ShdslSpanConfEntryAlarmProfile shehdsl2ShdslSpanConfControlAlarmProfile

Index of the modified entry.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

look at table.

look at table.

look at table.

This table provides overall status information of HDSL2/SHDSL spans. This table contains live data from equipment. As such, it is NOT persistent.

An entry in the hdsl2ShdslSpanStatusTable. Each entry represents the complete span in a single HDSL2/SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line.

Contains the actual number of repeaters/regenerators discovered in this HDSL2/SHDSL span.

Contains the maximum attainable line rate in this HDSL2/SHDSL span. This object provides the maximum rate the line is capable of achieving. This is based upon measurements made during line probing. This rate includes payload (user data) and any applicable framing overhead.

Contains the actual line rate in this HDSL2/SHDSL span. This should equal ifSpeed. This rate includes payload (user data) and any applicable framing overhead.

Contains the current Power Spectral Density (PSD) regional setting of the HDSL2/SHDSL span. Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.

This parameter contains the maximum attainable payload rate in this SHDSL span. This is based upon measurements made during line probing without including any framing overhead.

This parameter contains the actual payload rate in this SHDSL span. This is based upon measurements made during line probing without including any framing overhead.

The parameter show the selected PAM constellation is to be used. - SELECT_16_PAM - Use 16 PAM only - SELECT_32_PAM - Use 32 PAM only Select 16Pam limits the data rates from 192 kbps to 3840 kbps Select 32Pam limits the data rates from 768 kbps to 5696 kbps This is propietary extension for interfaces of type shdsl (169) only.

This table supports retrieval of unit inventory information available via the EOC from units in a HDSL2/SHDSL line. Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows: - xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed. As these entries are created/destroyed dynamically, they are NOT persistent.

An entry in the hdsl2ShdslInventoryTable. Each entry represents inventory information for a single unit in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the associated unit.

Each entry in this table corresponds to a physical element in a HDSL2/SHDSL Span. It is based on the EOC unit addressing scheme with reference to the xtuC.

Vendor ID as reported in an Inventory Response message.

Vendor model number as reported in an Inventory Response message.

Vendor serial number as reported in an Inventory Response message.

Vendor EOC version as reported in a Discovery Response message.

Version of the HDSL2/SHDSL standard implemented, as reported in an Inventory Response message.

Vendor list number as reported in an Inventory Response message.

Vendor issue number as reported in an Inventory Response message.

Vendor software version as reported in an Inventory Response message.

Equipment code conforming to ANSI T1.213, Coded Identification of Equipment Entities.

Other vendor information as reported in an Inventory Response message.

Contains the transmission mode capability of the SHDSL unit. Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.

This table supports configuration parameters for segment endpoints in a HDSL2/SHDSL line. As this table is indexed by ifIndex, it MUST be maintained in a persistent manner.

An entry in the hdsl2ShdslEndpointConfTable. Each entry represents a single segment endpoint in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem.

The side of the unit associated with this segment endpoint - Network/Customer side - as per the Hdsl2ShdslUnitSide textual convention.

The wire-pair of the modem associated with this segment endpoint as per the Hdsl2ShdslWirePair textual convention. wirePair1(1), -> two wire wirePair2(2), -> four wire wirePair3(3), -> six wire wirePair4(4) -> eight wire

This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero- length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString. Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected.

modifyshehdsl2ShdslEndpointConfEntry

First key for the modified entry. IfIndex of line.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Second key for modified entry.

Third key for the modified entry.

Forth key for the modified entry.

Look at table.

This table contains current status and performance information for segment endpoints in HDSL2/SHDSL Lines. As with other tables in this MIB indexed by ifIndex, entries in this table MUST be maintained in a persistent manner.

An entry in the hdsl2ShdslEndpointCurrTable. Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem.

The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message.

The current SNR margin for this endpoint as reported in a Status Response/SNR message.

Contains the current state of the endpoint. This is a bitmap of possible conditions. The various bit positions are: noDefect There no defects on the line. powerBackoff Indicates enhanced Power Backoff. deviceFault Indicates a vendor-dependent diagnostic or self-test fault has been detected. dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits. snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold. loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold. loswFailureAlarm Indicates a forward LOSW alarm. configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration. protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint. noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint. loopbackActive A loopback is currently active at this Segment Endpoint. This is intended to supplement ifOperStatus. Note that there is a 1-1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB.

Count of Errored Seconds (ES) on this endpoint since the xU was last restarted.

Count of Severely Errored Seconds (SES) on this endpoint since the xU was last restarted.

Count of CRC anomalies on this endpoint since the xU was last restarted.

Count of Loss of Sync Word (LOSW) Seconds on this endpoint since the xU was last restarted.

Count of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted.

Total elapsed seconds in the current 15-minute interval.

Count of Errored Seconds (ES) in the current 15-minute interval.

Count of Severely Errored Seconds (SES) in the current 15-minute interval.

Count of CRC anomalies in the current 15-minute interval.

Count of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval.

Count of Unavailable Seconds (UAS) in the current 15-minute interval.

Number of seconds that have elapsed since the beginning of the current 1-day interval.

Count of Errored Seconds (ES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.

Count of Severely Errored Seconds (SES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.

Count of CRC anomalies during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.

Count of Loss of Sync Word (LOSW) Seconds during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.

Count of Unavailable Seconds (UAS) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.

This object indicates the state of the tip/ring for the wire pair. normal(1), reversed(2)

This object indicates the activation or training state of the wire pair. preActivation(1), -> PreTrain activation(2), -> Training data(3) -> Trained

This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.

An entry in the hdsl2Shdsl15MinIntervalTable.

Performance Data Interval number. 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.

This variable indicates the time of storing this interval.

Count of Errored Seconds (ES) during the interval.

Count of Severely Errored Seconds (SES) during the interval.

Count of CRC anomalies during the interval.

Count of Loss of Sync Word (LOSW) Seconds during the interval.

Count of Unavailable Seconds (UAS) during the interval.

This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.

An entry in the hdsl2Shdsl1DayIntervalTable.

History Data Interval number. Interval 1 is the the most recent previous day; interval 30 is 30 days ago. Intervals 2..30 are optional.

This variable indicates the time of storing this interval.

The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.

Count of Errored Seconds (ES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.

Count of Severely Errored Seconds (SES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.

Count of CRC anomalies during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.

Count of Loss of Sync Word (LOSW) Seconds during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.

Count of Unavailable Seconds (UAS) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.

This table supports maintenance operations (eg. loopbacks) to be performed on HDSL2/SHDSL segment endpoints. This table contains live data from equipment. As such, it is NOT persistent.

An entry in the hdsl2ShdslEndpointMaintTable. Each entry corresponds to a single segment endpoint, and is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit and the side of the unit.

This object controls configuration of loopbacks for the associated segment endpoint. The status of the loopback is obtained via the hdsl2ShdslEndpointCurrStatus object. noLoopback(1), normalLoopback(2) is available for STU-C and STU-R. specialLoopback(3), normalLoopbackEocId9(8), specialLoopbackEocId9(9) are only available for STU-R. digitalLoopback(4) analogLoopback(5) interfaceLoopBack(6) localFramerLoopback(7) are only available for STU-C. Loopmode 2 and 3 are standard defined. All other modes are proprietary and not supported by all lines.

This object indicates the state of the tip/ring pair at the associated segment endpoint. normal(1), reversed(2)

This object configures the receiver at the associated segment endpoint to operate in default or enhanced power backoff mode. default(1), enhanced(2) is actual not supported for STU-C disable(3) is actual not supported for STU-R

This object enables the manager to trigger a soft restart of the modem at the associated segment endpoint. The manager may only set this object to the 'restart(2)' value, which initiates a restart. The agent will perform a restart after approximately 5 seconds. Following the 5 second period, the agent will restore the object to the 'ready(1)' state.

modifyshehdsl2ShdslEndpointMaintEntry

First key for the modified entry. IfIndex of line.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Second key for modified entry.

Third key for the modified entry.

Look at table.

Look at table.

Look at table.

This table supports maintenance operations for units in a HDSL2/SHDSL line. Entries in this table MUST be maintained in a persistent manner.

An entry in the hdsl2ShdslUnitMaintTable. Each entry corresponds to a single unit, and is indexed by the ifIndex of the HDSL2/SHDSL line and the UnitId of the associated unit.

This object configures the timeout value for loopbacks initiated at segments endpoints contained in the associated unit. A value of 0 disables the timeout.

This object indicates the DC power source being used by the associated unit. local(1), span(2)

modifyshehdsl2ShdslUnitMaintEntry

First key for the modified entry. IfIndex of line.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Second key for modified entry.

Look at table.

This table supports definitions of span configuration profiles for SHDSL lines. HDSL2 does not support these configuration options. This table MUST be maintained in a persistent manner.

Each entry corresponds to a single span configuration profile. Each profile contains a set of span configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile (see the hdsl2ShdslSpanConfProfile object). If an active entry is referenced in hdsl2ShdslSpanConfProfile, the entry MUST remain active until all references are removed.

A free running index for this table.

This object is the unique index associated with this profile. Entries in this table are referenced via the object hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry. This characters are not allowed: space : ?

This object configures the wire-interface operation for SHDSL Lines. twoWire(1), fourWire(2), fourWireBitInterleaved(3), fourWireByteInterleaveEnhanced(4), fourWireBitInterleaveEnhanced(5), sixWire(6), eightWire(7) Interfaces of type sdsl (96) support modes 1..5 and mode 3..5 are proprietary! Interfaces of type shdsl (169) will support mode 1..2 and 6..7!

This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. The minimum linerate should never be higher then the maximum linerate. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBits

This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. The maximum linerate should never be less then the minimum linerate. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBits

This object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for symmetric PSD is mandatory for all supported data rates. Support for asymmetric PSD is optional. symmetric(1), asymmetric(2), r1Asymmetric(3), r2Asymmetric(4) Mode 3..4 are propietary and only supported by interfaces of type sdsl (96).

This object specifies the regional setting for the SHDSL line. Minimum of one bit should always be set! Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.

This object enables/disables support for remote management of the units in a SHDSL line from the STU-R via the EOC. enabled(1), disabled(2)

This object enables/disables support for optional power feeding in a SHDSL line. noPower(1), powerFeed(2), wettingCurrent(3)

This object specifies the downstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.

This object specifies the downstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.

This object specifies the upstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.

This object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.

Contains indicates whether a target SNR margin is enabled or disabled. This is a bit-map of possible settings. Minimum of one bit should always be set! The various bit positions are: currCondDown current condition downstream target SNR margin enabled worstCaseDown worst case downstream target SNR margin enabled currCondUp current condition upstream target SNR margin enabled worstCaseUp worst case upstream target SNR margin enabled.

This object configures the clock reference for the STU-C in a SHDSL Line. Note: Interfaces of type sdsl (96) support only value localClk(1). Interfaces of type shdsl (169) support also the mode networkClk(2).

This object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate. If Line probe is disabled, the rate adaptation phase is skipped to shorten set up time. disable(1), enable(2)

The parameter allows the selection of which PAM constellation is to be used. - AUTO_PAM_SELECT - Automatic PAM selection - SELECT_16_PAM - Use 16 PAM only - SELECT_32_PAM - Use 32 PAM only Select 16Pam limits the data rates from 192 kbps to 3840 kbps Select 32Pam limits the data rates from 768 kbps to 5696 kbps +a--------------------------------------------------------+ | Soc4e-Dsl-API : SHDSL_LineTcPamSelModeGet | +---------------------------------------------------------+ | SHDSL_TcPamSelMode_t * pMode | | pointer to store current TC-PAM selection mode | ++--------------------------------------------------------+ | extented | +---------------------------------------------------------+ This is propietary extension for interfaces of type shdsl (169) only.

Specifies the TC-Layer. Set fix to 80)/ DSL_TC_ATM. (0) - DSL_TC_ATM (1) - DSL_TC_EFM (2) - DSL_TC_HDLC +a--------------------------------------------------------+ | Soc4e-Dsl-API : DSL_SystemInterfaceConfigGet | +---------------------------------------------------------+ | DSL_SystemInterfaceConfig_t * pData | | DSL_TcLayerSelection_t | +d--------------------------------------------------------+ | Soc4e-Drv-Cmd : ACK_PMD_EndpointAlarmConfig | +x--------------------------------------------------------+ | sics | +---------------------------------------------------------+ This is propietary extension for interfaces of type shdsl (169) only.

createshehdsl2ShdslSpanConfProfile modifyshehdsl2ShdslSpanConfProfile deleteshehdsl2ShdslSpanConfProfile

Key for the modified or deleted entry. NE will choose this number during create.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Name for new profile.

Look at table. twoWire(1), fourWire(2), fourWireBitInterleaved(3), fourWireByteInterleaveEnhanced(4), fourWireBitInterleaveEnhanced(5), sixWire(6), eightWire(7) Interfaces of type sdsl (96) support modes 1..5 and mode 3..5 are proprietary! Interfaces of type shdsl (169) will support mode 1..2 and 6..7!

Look at table. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBits

Look at table. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBits

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table. Note: Interfaces of type sdsl (96) support only value localClk(1). Interfaces of type shdsl (169) support also the mode networkClk(2).

Look at table.

Look at table. This is propietary extension for interfaces of type shdsl (169) only.

Look at table. This is propietary extension for interfaces of type shdsl (169) only.

This table supports definitions of alarm configuration profiles for HDSL2/SHDSL segment endpoints. This table MUST be maintained in a persistent manner.

Each entry corresponds to a single alarm configuration profile. Each profile contains a set of parameters for setting alarm thresholds for various performance attributes monitored at HDSL2/SHDSL segment endpoints. Profiles may be created/deleted using the row creation/deletion mechanism via hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active entry is referenced in either hdsl2ShdslSpanConfAlarmProfile or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain active until all references are removed.

A free running index for this table.

This object is the unique index associated with this profile. This characters are not allowed: space : ?

This object configures the loop attenuation alarm threshold. When the current value of hdsl2ShdslEndpointCurrAtn reaches or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing MAY be generated.

This object configures the SNR margin alarm threshold. When the current value of hdsl2ShdslEndpointCurrSnrMgn reaches or drops below this threshold, a hdsl2ShdslSNRMarginCrossing MAY be generated.

This object configures the threshold for the number of errored seconds (ES) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/ exceeds this value, a hdsl2ShdslPerfESThresh MAY be generated. At most one notification will be sent per interval per endpoint.

This object configures the threshold for the number of severely errored seconds (SES) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh MAY be generated. At most one notification will be sent per interval per endpoint.

This object configures the threshold for the number of CRC anomalies within any given 15-minute performance data collection interval. If the value of CRC anomalies in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be generated. At most one notification will be sent per interval per endpoint.

This object configures the threshold for the number of Loss of Sync Word (LOSW) Seconds within any given 15-minute performance data collection interval. If the value of LOSW in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated. At most one notification will be sent per interval per endpoint.

This object configures the threshold for the number of unavailable seconds (UAS) within any given 15-minute performance data collection interval. If the value of UAS in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfUASThresh MAY be generated. At most one notification will be sent per interval per endpoint.

createshehdsl2ShdslEndpointAlarmConfProfile modifyshehdsl2ShdslEndpointAlarmConfProfile deleteshehdsl2ShdslEndpointAlarmConfProfile

Key for the modified or deleted entry. NE will choose this number during create.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Name for new profile.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

Look at table.

This notification indicates that the loop attenuation threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint.

This notification indicates that the SNR margin threshold (as per the hdsl2ShdslEndpointThreshSNRMargin value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint.

This notification indicates that the errored seconds threshold (as per the hdsl2ShdslEndpointThreshES value) has been reached/ exceeded for the HDSL2/SHDSL segment endpoint.

This notification indicates that the severely errored seconds threshold (as per the hdsl2ShdslEndpointThreshSES value) has been reached/exceeded for the HDSL2/SHDSL Segment Endpoint.

This notification indicates that the CRC anomalies threshold (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has been reached/exceeded for the HDSL2/SHDSL Segment Endpoint.

This notification indicates that the LOSW seconds threshold (as per the hdsl2ShdslEndpointThreshLOSWS value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint.

This notification indicates that the unavailable seconds threshold (as per the hdsl2ShdslEndpointThreshUAS value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint.

This notification indicates that a mismatch has been detected between the number of repeater/regenerator units configured for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters object and the actual number of repeater/regenerator units discovered via the EOC.

This notification indicates that an endpoint maintenance loopback command failed for an HDSL2/SHDSL segment.

This notification indicates that the bit setting for powerBackoff in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates that the bit setting for deviceFault in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates that the bit setting for dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates that the bit setting for configInitFailure in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates that the bit setting for protocolInitFailure in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates that the bit setting for noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed.

This notification indicates impending unit failure due to loss of local power (last gasp).

This alarm informs the link between the line card and modem is disconnected for unidentied reason, not dying gasp.

This alarm informs the link between the line card and modem is disconnected for dying gasp.

This alarm informs the link between the line card and modem is disconnected for loss of signal.

This alarm informs the link between the line card and modem is disconnected for loss of frame.

Notification for a complete LineParamsEntry-Modify-Command.

Notification for a complete SpanConfEntry-Modify-Command.

Notification for a complete SpanConfEntry-Modify-Command.

Notification for a complete EndPointConfEntry-Modify-Command.

Notification for a complete EndPointMaintEntry-Modify-Command.

Notification for a complete UnitMaintEntry-Modify-Command.

Notification for a complete SpanConfProfileEntry-Create-Command.

Notification for a complete SpanConfProfileEntry-Modify-Command.

Notification for a complete SpanConfProfileEntry-Delete-Command.

Notification for a complete EndPointAlarmProfileEntry-Create-Command.

Notification for a complete EndPointAlarmProfileEntry-Modify-Command.

Notification for a complete EndPointAlarmProfileEntry-Delete-Command.

Trap for long running profile modification result.

Trap for long running profile modification result.

The VccTp-Table.

This table contains the VccTp-Configurations. There will be one entry for every shdsl-interface available per default. This default entry should never be deleted.

Index for that table. The index will follow this rule: VccTpIndex = (VccTpSubLayerIndex << 4) + VccTpNumber

ifIndex of the underlaying shdsl-interface.

This is the logical number of VccTP on the corresponding interface. Maximum value is 1.

The VPI - Value.

The Vci - Value.

The OAM level for loop test on VP/VC level. Valid: f5 (for VC).

The type of loop test . For EndToEnd loop test loop location ID is FF..FF.

Possible values: segSuccess(0), segFailure(1), endToEndSuccess(2), endToEndFailure(3), aborted(4), progress(5), notAvailable(65535)

Test cell loopback location. It is an identifier known by the crafts person identifying a ATM node in the ATM network. For EndToEnd loop test the default value is valid.

Index to the AlarmSeverityProfileTable. Defines the actual AlarmSeverities for all alarms per VccTp.

modifyShdslVccTp: sheShdslVccTpControlIndex sheShdslVccTpControlVpi sheShdslVccTpControlVci sheShdslVccTpControlAlarmSeverityIndex modifyShdslVccTpLoopTest: sheShdslVccTpControlIndex sheShdslVccTpControlLoopTest createShdslVccTp: sheShdslVccTpControlSubLayerIndex sheShdslVccTpControlVpi sheShdslVccTpControlVci deleteShdslVccTp: sheShdslVccTpControlIndex

Index of the Table-entry to be configured.

The status of a user command.

The maximum wait time for the manager for a long running user command.

The result of the last user command.

The time stamp of the last command (end of command).

Description.

Vpi

Vci

Actual LoopTest-Value. Only None or endToEnd will be accepted.

Index of the used AlarmSeverityProfile.

Configuration notification.

RDI detected.

AIS detected.

Notification in case of failed VccTp-Configuration.

Configuration notification.

Configuration notification.

Description.

Description.

Description.

Description.

Description.