MICOM-ISDN-MIB: View SNMP OID List / Download MIB

NAME = ; DESC = Table containing configuration and operational \ parameters for all physical Basic Rate interfaces \ on this managed device. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the ISDN Basic Rate Table. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The line topology to be used for this interface. \ Note that setting nvmIsdnBasicRateIfType to isdns(75) \ does not necessarily mean a line topology of \ point-to-multipoint. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'pointToPoint': 1, 'pointToMultipoint': 2.

NAME = ; DESC = The signaling channel operational mode for this \ interface. If dialup(1), there is a signaling channel \ on this interface and the corresponding operational \ object, isdnBasicRateSignalMode (see rfc2127.mib), \ will be active(1). If leased(2), a signaling channel \ is not available and the corresponding operational \ object, isdnBasicRateSignalMode, will be inactive(2). \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'dialup': 1, 'leased': 2.

NAME = ; DESC = ISDN signaling table containing configuration and \ operational parameters for all ISDN signaling \ channels on this managed device. (Configuration) ; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the ISDN Signaling Table. To create a \ new entry, only nvmIsdnSignalingProtocol needs to be \ specified before nvmIsdnSignalingStatus can become \ active(1). (Configuration) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnSignalingTable. (Configuration); HELP = This managed object corresponds to the port index used \ in the ICM ('primary' and 'backup' ports supported).; CAPABILITIES = ;

NAME = ; DESC = The particular protocol type supported by the \ switch providing access to the ISDN network \ to which this signaling channel is connected. (Configuration); HELP = Enumerations supported by access device are 2, 3, 6, 7, \ 9, 12, 13, 17, and 19.; CAPABILITIES = ; Enumeration: 'ess5': 6, 'ins64': 17, 'itr6': 19, 'etsi': 3, 'dms100': 7, 'vn3': 13, 'vn2': 12, 'qsig': 23, 'ni1': 9, 'dss1': 2.

NAME = ; DESC = The ISDN Address to be assigned to this signaling \ channel. More specifically, this is the 'Calling Address \ information element' as being passed to the switch \ in outgoing call setup messages. \ It can be an EAZ (1TR6), a calling number (DSS1, \ ETSI)or any other number necessary to identify a \ signaling interface. If there is no such number defined \ or required, this is a zero length string. It is represented \ in DisplayString form. \ Incoming calls can also be identified by this number. \ If the Directory Number, i.e. the Called Number in \ incoming calls, is different to this number, the \ isdnDirectoryTable has to be used to specify all \ possible Directory Numbers. \ The format of this information largely depends on the \ type of switch or PBX the device is connected to. Therefore, \ the detailed format of this information is not \ specified and is implementation dependent. \ If possible, the agent should implement this information \ using the E.164 number format. In this case, the number \ must start with '+'. Otherwise, IA5 number digits must \ be used. (Configuration) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = Supplementary information to the ISDN address assigned \ to this signaling channel. Usually, this is the \ subaddress as defined in Q.931. \ If there is no such number defined or required, this is \ a zero length string. \ The subaddress is used for incoming calls as well as \ for outgoing calls. \ The subaddress is an user supplied string of up to 20 \ IA5 characters and is transmitted transparently through \ the network. (Configuration) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = Indicates whether isdnMibCallInformation traps \ should be generated for calls on this signaling \ channel. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'disabled': 2, 'enabled': 1.

NAME = ; DESC = Table containing configuration and statistics \ information for all LAPD (D channel Data Link) \ interfaces on this managed device. \ Only statistical information which is not already being \ counted in the ifTable is being defined in this table. \ This table is an extension to the LAPD table resident in \ the RFC2127 MIB. (Operational) HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the LAPD Table. (Extensions to LAPD \ table in RFC2127 MIB.) (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the transmit \ window size (maximum number of outstanding \ unacknowledged information frames. (Operational); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the receive \ window size (maximum number of outstanding \ unacknowledged information frames. (Operational); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the maximum \ transmit frame size (in bytes). (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the maximum \ receive frame size (in bytes). (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T200 value (in milliseconds). T200 is the time \ to wait for an acknowledgment to a frame \ before initiating recovery. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T201 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ check messages. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T202 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ request messages. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T203 value (in milliseconds). T203 is the maximum \ time allowed without frames being exchanged. \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ TM20 value (in milliseconds) for TEI management. \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter N200. This is the maximum number \ of retransmissions of a frame. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter N202. This is the maximum number \ of transmissions of a TEI identity request \ message. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter NM20 (for TEI management). \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = Table containing configuration and statistics \ information for all LAPD (D channel Data Link) \ interfaces on this managed device. \ Only statistical information which is not already being \ counted in the ifTable is being defined in this table. \ This table is an extension to the LAPD table resident in \ the RFC2127 MIB. (Configuration) HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the LAPD Table. (Extensions to LAPD \ table in RFC2127 MIB.) (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the transmit \ window size (maximum number of outstanding \ unacknowledged information frames. (Configuration); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the receive \ window size (maximum number of outstanding \ unacknowledged information frames. (Configuration); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the maximum \ transmit frame size (in bytes). (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the maximum \ receive frame size (in bytes). (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T200 value (in milliseconds). T200 is the time \ to wait for an acknowledgment to a frame \ before initiating recovery. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T201 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ check messages. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T202 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ request messages. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ T203 value (in milliseconds). T203 is the maximum \ time allowed without frames being exchanged. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the timer \ TM20 value (in milliseconds) for TEI management. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter N200. This is the maximum number \ of retransmissions of a frame. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter N202. This is the maximum number \ of transmissions of a TEI identity request \ message. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the Retry \ Counter NM20 (for TEI management). \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = Table containing configuration for Terminal \ Endpoints. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the Terminal Endpoint Table. The value \ of nvmIsdnEndpointIfType must be supplied for a row \ in this table to become active. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnEndpointTable. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The type of TEI (Terminal Endpoint Identifier) \ used for this Terminal Endpoint. In case of dynamic(1), \ the TEI value is selected by the switch. In \ case of static(2), a valid TEI value has to be \ entered in the nvmIsdnEndpointTeiValue object. \ The default value for this object depends on the \ interface type as well as the Terminal Endpoint type. \ On Primary Rate interfaces the default value is \ static(2). On Basic Rate interfaces the default value \ is dynamic(1) for isdn(63) Terminal Endpoints and \ static(2) for x25ple(40) Terminal Endpoints. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'static': 2, 'dynamic': 1.

NAME = ; DESC = The TEI (Terminal Endpoint Identifier) value \ for this Terminal Endpoint. If nvmIsdnEndpointTeiType \ is set to static(2), valid numbers are 0..63, \ while otherwise the value is set internally. \ The default value of this object is 0 for static \ TEI assignment. \ The default value for dynamic TEI assignment is also \ 0 as long as no TEI has been assigned. After TEI \ assignment, the assigned TEI value is returned. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The Service profile IDentifier (SPID) information \ for this Terminal Endpoint. \ The SPID is composed of 9-20 numeric characters. \ This information has to be defined in addition to \ the local number for some switch protocol types, \ e.g. Bellcore NI-1 and NI-2. \ If this object is not required, it is a \ zero length string. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = Table containing Directory Numbers. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = An entry in the Directory Number Table. All objects \ in an entry must be set for a new row to become active. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnDirectoryTable. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = A Directory Number. Directory Numbers are used \ to identify incoming calls on the signaling \ channel given in nvmIsdnDirectorySigIndex. \ The format of this information largely depends on the \ type of switch or PBX the device is connected to. \ Therefore, the detailed format of this information is \ not specified and is implementation dependent. \ If possible, the agent should implement this information \ using the E.164 number format. In this case, the number \ must start with '+'. Otherwise, IA5 number digits must \ be used. (Configuration); HELP = This ICM variable contains the remote address for which \ incoming calls are handled.; CAPABILITIES = ;

NAME = ; DESC = An index pointing to an ISDN signaling channel. \ Incoming calls are accepted on this \ signaling channel if the nvmIsdnDirectoryNumber is \ presented as Called Number in the SETUP message. \ (Configuration); HELP = This is an index to a link in the dialCtlPeerCfg table \ (and not an index to a signaling channel). The ICM \ changes the meaning of this managed object in order \ to be able to extract the link for which the directory \ number is specified.; CAPABILITIES = ;

NAME = ; DESC = For software releases prior to 3.0 \ this object only supported enumerations of \ add and delete with an access of write-only. \ This object is used to create and delete rows in the \ nvmIsdnDirectoryTable. Upon creation of a row, the \ the row status is internally set to 'active'. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'active': 3, 'add': 1, 'delete': 2.

NAME = ; DESC = The security level for acceptance of incoming calls. \ acceptNone(1) - incoming calls will not be accepted. \ acceptAll(2) - incoming calls will be accepted, even. \ if there is no matching entry in the nvmDialCtlPeerCfgTable. \ acceptKnown(3) - incoming calls will be accepted only \ if there is a matching entry in the nvmDialCtlPeerCfgTable. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; Enumeration: 'acceptAll': 2, 'acceptNone': 1, 'acceptKnown': 3.

NAME = ; DESC = This object indicates whether nvmDialCtlPeerCallInformation \ and nvmDialCtlPeerCallSetup traps should be generated for \ all peers. If the value of this object is enabled(1), \ traps will be generated for all peers. If the value \ of this object is disabled(2), traps will be generated \ only for peers having nvmDialCtlPeerCfgTrapEnable set \ to enabled(1). (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; Enumeration: 'disabled': 2, 'enabled': 1.

NAME = ; DESC = The list of peers from which the managed device \ will accept calls or to which it will place them. \ This table is an extension to the Peer Group table \ resident in the RFC2128 MIB. (Operational) HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ;

NAME = ; DESC = An entry in the Peer Group Table. (Extension to \ Peer Group table in RFC2128 MIB. (Operational);\ HELP = ; CAPABILITIES = ;

NAME = ; DESC = This object identifies a single peer. There may \ be several entries in this table for one peer, \ defining different ways of reaching this peer. \ Thus, there may be several entries in this table \ with the same value of mcmDialCtlPeerCfgId. \ Multiple entries for one peer may be used to support \ multilink as well as backup lines. \ A single peer will be identified by a unique value \ of this object. Several entries for one peer MUST \ have the same value of mcmDialCtlPeerCfgId, but different \ ifEntries and thus different values of ifIndex. \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the B channel to be used \ for leased lines. (Operational); HELP = Note: 0 = 'any'. This managed object is not part of the \ original Dial Control MIB (RFC2128). This proprietary \ object was added for ICM purposes.; CAPABILITIES = ;

NAME = ; DESC = The list of peers from which the managed device \ will accept calls or to which it will place them. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ;

NAME = ; DESC = Configuration data for a single Peer. This entry is \ effectively permanent, and contains information \ to identify the peer, how to connect to the peer, \ how to identify the peer and its permissions. \ The value of nvmDialCtlPeerCfgOriginateAddress must be \ specified before a new row in this table can become \ active(1). Any writeable parameters in an existing entry \ can be modified while the entry is active. The modification \ will take effect when the peer in question will be \ called the next time. \ An entry in this table can only be created if the \ associated ifEntry already exists. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = This object identifies a single peer. There may \ be several entries in this table for one peer, \ defining different ways of reaching this peer. \ Thus, there may be several entries in this table \ with the same value of nvmDialCtlPeerCfgId. \ Multiple entries for one peer may be used to support \ multilink as well as backup lines. \ A single peer will be identified by a unique value \ of this object. Several entries for one peer MUST \ have the same value of nvmDialCtlPeerCfgId, but different \ ifEntries and thus different values of ifIndex. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the B channel to be used \ for leased lines. (Configuration); HELP = Note: 0 = 'any'. This managed object is not part of the \ original Dial Control MIB (RFC2128). This proprietary \ object was added for ICM purposes.; CAPABILITIES = ;

NAME = ; DESC = ifIndex value of an interface the peer will have to be \ called on. For example, on an ISDN interface, this can be \ the ifIndex value of a D channel or the ifIndex value of a \ B channel, whatever is appropriate for a given peer. \ As an example, for Basic Rate leased lines it will be \ necessary to specify a B channel ifIndex, while for \ semi-permanent connections the D channel ifIndex has \ to be specified. \ If the interface can be dynamically assigned, this object \ has a value of zero. (Configuration); HELP = The LowerIf is the ifIndex value of a D channel index \ (primary or backup port for a semi-permanent connection), \ or the ifIndex value of a B channel for a leased line.; CAPABILITIES = ;

NAME = ; DESC = Call Address at which the peer will be called. \ Think of this as the set of characters following 'ATDT ' \ or the 'phone number' included in a D channel call request. \ The structure of this information will be switch type \ specific. If there is no address information required \ for reaching the peer, i.e., for leased lines, \ this object will be a zero length string. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = Subaddress at which the peer will be called. \ If the subaddress is undefined for the given media or \ unused, this is a zero length string. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = Closed User Group at which the peer will be called. \ If the Closed User Group is undefined for the given media \ or unused, this is a zero length string. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The desired information transfer speed in bits/second \ when calling this peer. \ The detailed media specific information, e.g. information \ type and information transfer rate for ISDN circuits, \ has to be extracted from this object. \ If the transfer speed to be used is unknown or the default \ speed for this type of interfaces, the value of this object \ may be zero. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The Information Transfer Capability to be used when \ calling this peer. \ speech(2) refers to a non-data connection, whereas \ audio31(6) and audio7(7) refer to data mode \ connections. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'fax': 10, 'unrestrictedDigital': 3, 'unrestrictedDigital56': 4, 'audio7': 7, 'restrictedDigital': 5, 'audio31': 6, 'other': 1, 'speech': 2, 'packetSwitched': 9, 'video': 8.

NAME = ; DESC = Applicable permissions. callback(4) either rejects the \ call and then calls back, or uses the 'Reverse charging' \ information element if it is available. \ Note that callback(4) is supposed to control charging, not \ security, and applies to callback prior to accepting a \ call. Callback for security reasons can be handled using \ PPP callback. (Configuration); HELP = Access device ISDN does not support 'callback(4)'. The value \ 'originate' is for outgoing calls. The value 'answer' is \ for incoming calls.; CAPABILITIES = ; Enumeration: 'answer': 2, 'both': 3, 'none': 5, 'originate': 1.

NAME = ; DESC = The number of calls to a non-responding address \ that may be made. A retry count of zero means \ there is no bound. The intent is to bound \ the number of successive calls to an address \ which is inaccessible, or which refuses those calls. \ Some countries regulate the number of call retries \ to a given peer that can be made. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The time in seconds between call retries if a peer \ cannot be reached. \ A value of zero means that call retries may be done \ without any delay. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The time in seconds after which call attempts are \ to be placed again after a peer has been noticed \ to be unreachable, i.e. after nvmDialCtlPeerCfgCallRetries \ unsuccessful call attempts. \ A value of zero means that a peer will not be called \ again after nvmDialCtlPeerCfgCallRetries unsuccessful call \ attempts. (Configuration); HELP = This value is the time to wait with another call \ retry after nvmDialCtlPeerCfgCallRetries unsuccessful \ calls. ICM uses the default value of zero, which means \ that a peer will not be called again after \ nvmDialCtlPeerCfgCallRetriesattempts. The whole call \ retry logic will be implemented.; CAPABILITIES = ;

NAME = ; DESC = This object indicates whether dialCtlPeerCallInformation \ and dialCtlPeerCallSetup traps should be generated for \ this peer. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'disabled': 2, 'enabled': 1.

NAME = ; DESC = For software releases prior to 3.0 \ this object only supported enumerations of \ add and delete with an access of write-only. \ This object is used to create and delete rows in the \ nvmDialCtlPeerCfgTable. Upon creation of a row, the \ the row status is internally set to 'active'. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'active': 3, 'add': 1, 'delete': 2.

NAME = ; DESC = The upper limit on the number of entries that the \ callHistoryTable may contain. A value of 0 \ will prevent any history from being retained. When \ this table is full, the oldest entry will be deleted \ and the new one will be created. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The ISDN Signaling Statistics counter reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the ISDN Signaling Statistics counter \ reset table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The value of this object represents a unique \ identifier used as the index into the \ ISDN Signaling Statistics counter reset table. \ This index specifies the particular row of counter \ objects to be reset (objects defined in the ISDN \ Signaling Statistics table in the MIB file rfc2127.mib). \ This index has the identical value as the object \ isdnSignalingIndex (also defined in the MIB \ file rfc2127.mib).; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of counters in \ the ISDN Signaling Statistics table defined \ in the MIB file rfc2127.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ isdnSigStatsInCalls \ isdnSigStatsInConnected \ isdnSigStatsOutCalls \ isdnSigStatsOutConnected \ isdnSigStatsChargedUnits; CAPABILITIES = ; Enumeration: 'reset': 1.

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The ISDN LAPD counter reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the ISDN LAPD counter \ reset table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The value of this object represents a unique \ identifier used as the index into the ISDN \ LAPD counter reset table. This index specifies \ the particular row of counter objects to be reset \ (objects defined in the ISDN LAPD table in the \ MIB file rfc2127.mib). This index has the \ identical value as the object ifIndex (defined in \ the IF-MIB).; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of counters in \ the ISDN LAPD table defined in the MIB \ file rfc2127.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ isdnLapdPeerSabme \ isdnLapdRecvdFrmr; CAPABILITIES = ; Enumeration: 'reset': 1.

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The Dial Control Peer Statistics gauge reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the Dial Control Peer Statistics gauge \ reset table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of gauges in \ the Dial Control Peer Statistics table defined \ in the MIB file rfc2128.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ dialCtlPeerStatsConnectTime \ dialCtlPeerStatsChargedUnits \ dialCtlPeerStatsSuccessCalls \ dialCtlPeerStatsFailCalls \ dialCtlPeerStatsAcceptCalls \ dialCtlPeerStatsRefuseCalls; CAPABILITIES = ; Enumeration: 'reset': 1.

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The Dial Control Call Active gauge reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the Dial Control Call Active gauge \ reset table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of gauges in \ the Dial Control Call Active table defined \ in the MIB file rfc2128.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ callActiveChargedUnits \ callActiveTransmitPackets \ callActiveTransmitBytes \ callActiveReceivePackets \ callActiveReceiveBytes; CAPABILITIES = ; Enumeration: 'reset': 1.

NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will clear \ the entire Dial Control Call History table \ defined in the MIB file rfc2128.mib.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; Enumeration: 'reset': 1.