HPN-ICF-DOT11-CFG-MIB: View SNMP OID List / Download MIB

VENDOR: HEWLETT-PACKARD


 Home MIB: HPN-ICF-DOT11-CFG-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 hpnicfDot11CFG 1.3.6.1.4.1.11.2.14.11.15.2.75.4
This MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.
     hpnicfDot11GlobeConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1
         hpnicfDot11GlobalCountryCode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.1 octet string read-write
Represents the country code for wireless network.
         hpnicfDot11StaKeepALiveTimerIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.2 unsigned32 read-write
Represents the interval of the keep alive requests sent between AP and STA. Default value 0 : The keep alive function is disabled.
         hpnicfDot11StaIdleTimerIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.3 integer32 read-write
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
         hpnicfDot11BroadcastProbeReply 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.4 truthvalue read-write
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
         hpnicfDot11APScanMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.5 integer read-write
Represents the scanning mode for AP. The following values are supported: active - AP will actively do scan. passive - AP will passively do scan. Enumeration: 'active': 1, 'passive': 2.
         hpnicfDot11ACCtrlTunnelSecSupport 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.6 hpnicfdot11tunnelsecschemtype read-write
Represents what security schemes are supported for CAPWAP Control tunnel.
         hpnicfDot11ACDataTunnelSecSupport 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.7 hpnicfdot11tunnelsecschemtype read-write
Represents what security schemes are supported for CAPWAP data tunnel. The cleartxt is the default scheme.
         hpnicfDot11ACAutoAPSupport 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.8 truthvalue read-write
Represents enable the auto AP functionality or not. 'true' : The auto AP functionality is enabled. 'false': The auto AP functionality is disabled
         hpnicfDot11AutoAPName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.9 octet string read-write
Represents the name of auto AP that needs to be made persistent. When read the value from the node, NULL value be returned.
         hpnicfDot11PersistentName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.10 octet string read-write
Represents the new name of auto AP after being made persistent. When read the value from the node, NULL value be returned.
         hpnicfDot11IntfTrapThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.11 integer32 read-write
Represents threshold of interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
         hpnicfDot11MonitorInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.12 unsigned32 read-write
Represents the monitoring interval. Default value 0 : The monitoring functionality is changed to real-time mode.
         hpnicfDot11SampleInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.13 unsigned32 read-write
Represents the sampling interval. Default value 0 : The sampling functionality is disabled.
         hpnicfDot11ChnlSwitChkInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.14 unsigned32 read-write
Represents the checking interval of channel switch.
         hpnicfDot11APUserUplimit 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.15 unsigned32 read-write
Represents the upper limit of user which has access to this AP.
         hpnicfDot11APL2IsolateEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.16 truthvalue read-write
Represents enable the layer2 isolation or not. 'true' : The layer2 isolation functionality is enabled. 'false': The layer2 isolation functionality is disabled.
         hpnicfDot11APBSSIDSupportNum 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.17 integer32 read-only
Represents the max number of BSSID supported by Current AP.
         hpnicfDot11APLastUpdateStatTime 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.18 dateandtime read-only
Represents date and time update statistic information lately.
         hpnicfDot11APDoSProtectEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.19 truthvalue read-write
Represents enable the DOS protection or not. 'true' : The DOS protection functionality is enabled. 'false': The DOS protection functionality is disabled.
         hpnicfDot11MaxAPPerIf 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.20 unsigned32 read-write
Represents max AP number that can be connected to AC interface.
         hpnicfDot11SampleTimeStamp 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.21 dateandtime read-only
Represents the start time of current sample period.
         hpnicfDot11UplinkTrackId 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.22 unsigned32 read-write
Represents the track id of AP. Default value 0 : The uplink track function for AP is disabled.
         hpnicfDot11RtCollectSwitch 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.23 truthvalue read-write
This object is used to turn on/off real-time statistics collection between AC and AP. If the value is true, hpnicfDot11RtCollectIntvl will take effect. Otherwise, hpnicfDot11RglCollectIntvl will take effect.
         hpnicfDot11RglCollectIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.24 integer32 read-write
This object represents interval to regularly collect statistics from AC to AP.
         hpnicfDot11RtCollectIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.25 integer32 read-write
This object represents interval to collect real-time statistics from AC to AP.
         hpnicfDot11AllAPCpuUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.26 integer32 read-write
The CPU usage threshold for all AP.
         hpnicfDot11AllAPMemUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.27 integer32 read-write
The memory usage threshold for all AP.
         hpnicfDot11AdjIntfTrapThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.28 integer32 read-write
Represents threshold of adjacent interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
         hpnicfDot11AllAPMonitorMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.29 integer read-write
Represents what work mode for All AP. The following values are supported: normal, - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. Enumeration: 'hybrid': 3, 'monitor': 2, 'normal': 1.
         hpnicfDot11GlobalApFmwUpdState 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.30 integer read-write
Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. Enumeration: 'enable': 1, 'disable': 2.
         hpnicfDot11ACNasIDCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.31 octet string read-write
Represents the NAS-ID of current AC.
     hpnicfDot11PolicyConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2
         hpnicfDot11RadioPolicyTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1 no-access
The table defines the parameters for radio policy, as per radio policy of CLI. One radio policy could be assigned to the different radios (AP).
             hpnicfDot11RadioPolicyEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1 no-access
Each entry contains information of each radio policy.
                 hpnicfDot11RadioPolicyName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.1 octet string no-access
Represents the name of radio policy.
                 hpnicfDot11BeaconInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.2 integer32 read-only
Represents the interval for Beacon management frame.
                 hpnicfDot11DtimInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.3 integer32 read-only
Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
                 hpnicfDot11RtsThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.4 integer32 read-only
Represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
                 hpnicfDot11FragThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.5 integer32 read-only
Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
                 hpnicfDot11ShortRetryThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.6 integer32 read-only
Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, which shall be made before a failure condition is indicated.
                 hpnicfDot11LongRetryThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.7 integer32 read-only
Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated.
                 hpnicfDot11MaxRxLifetime 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.8 unsigned32 read-only
Represents the elapsed time. After the time specified by hpnicfDot11MaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
                 hpnicfDot11RdoPolicyRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.9 rowstatus read-only
The status of this table entry.
                 hpnicfDot11RdoClientMaxCount 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.10 integer32 read-only
Represent the maximum number of stations supported by this radio policy.
                 hpnicfDot11BeaconIntervalMs 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.11 integer32 read-only
Represents the interval for Beacon management frame.
         hpnicfDot11ServicePolicyTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2 no-access
The table defines the parameters for ESS, as per service policy of CLI. One service policy could be assigned to the different radios (AP).
             hpnicfDot11ServicePolicyEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1 no-access
Each entry contains information of each service policy.
                 hpnicfDot11ServicePolicyID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.1 hpnicfdot11servicepolicyidtype no-access
Represents the ID of each service policy.
                 hpnicfDot11SSIDName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.2 hpnicfdot11ssidstringtype read-only
Represents the ESS. As per CLI, the value of service policy name will be SSID.
                 hpnicfDot11SSIDHidden 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.3 truthvalue read-only
This attribute controls whether the SSID will be advertised in the beacon frame. If it is true, then SSID will not be advertised in the beacon frame.
                 hpnicfDot11AuthenMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.4 hpnicfdot11authentype read-only
Represents the Authentication mode defined by 802.11.
                 hpnicfDot11SSIDEncryptionMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.5 hpnicfdot11ssidencryptmodetype read-only
Represents the encryption mode for this ESS.
                 hpnicfDot11WlanInfBindingType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.6 octet string read-only
Represents the service policy will bind to what kind of data forwarding interface.
                 hpnicfDot11WlanInfBindingID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.7 integer32 read-only
Represents the interface ID of the interface that ESS will bind to. If the value is set to -1, the binding will be removed.
                 hpnicfDot11SrvPolicyRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.8 rowstatus read-only
The status of this table entry.
                 hpnicfDot11ClientMaxCount 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.9 integer32 read-only
Represent the maximum number of stations supported by this service policy.
                 hpnicfDot11SPInCirMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.10 hpnicfdot11cirmode read-only
CIR(committed information rate) mode of inbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
                 hpnicfDot11SPInCirValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.11 integer32 read-only
Represents the CIR of inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
                 hpnicfDot11SPOutCirMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.12 hpnicfdot11cirmode read-only
CIR(committed information rate) mode of outbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
                 hpnicfDot11SPOutCirValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.13 integer32 read-only
Represents the CIR of outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
                 hpnicfDot11WlanInfPVID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.14 integer32 read-only
Represents the VLAN ID of SSID.
                 hpnicfDot11SPInCirStaticValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.15 integer32 read-only
Represents the CIR of inbound direction for static CIR mode.
                 hpnicfDot11SPOutCirStaticValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.16 integer32 read-only
Represents the CIR of outbound direction for static CIR mode.
                 hpnicfDot11SPIsolate 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.17 truthvalue read-only
If it is true, then stations connected with the service policy are isolated.
                 hpnicfDot11WlanexAuthServerIP 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.18 ipaddress read-only
Represents the IP address of the Wlanex Authentication server
                 hpnicfDot11SPBeaconMeasEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.19 truthvalue read-only
If it is true, then beacon-measurement is enabled.
                 hpnicfDot11SPBeaconMeasType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.20 integer read-only
Represents what the work mode for BeaconMeasurement type. The following values are supported: passive, - BeaconMeasurement will use the passive type. active - BeaconMeasurement will use the active type. beaconTable - BeaconMeasurement will use the beacon table type. Enumeration: 'passive': 1, 'active': 2, 'beaconTable': 3.
                 hpnicfDot11SPBeaconMeasInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.21 integer32 read-only
Represents the beacon-measurement interval.
                 hpnicfDot11AuthenModeCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.22 integer read-only
Represents the Authentication mode defined by 802.11. Enumeration: 'opensystem': 0, 'sharedkey': 1.
                 hpnicfDot11SecIEStatusCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.23 integer read-only
To enable the security Information element in the beacon and probe response frames sent by AP. Enumeration: 'wlanex': 3, 'none': 0, 'wpa2': 2, 'wpa': 1.
                 hpnicfDot11SecurityCiphersCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.24 integer read-only
The WLAN system support the following cipher type for data frame encryption. none wep40 wep104 tkip aesccmp wpi-SMS4 When the value of node equals to zero, it means no configuration or undo operation. Enumeration: 'none': 0, 'wpisms4': 5, 'wep104': 2, 'tkip': 3, 'wep40': 1, 'aesccmp': 4.
                 hpnicfDot11SrvPolicyStatusCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.25 integer read-only
The status of the Service Policy. Enumeration: 'on': 1, 'off': 0.
                 hpnicfDot11SSIDHiddenCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.26 hpnicfdot11truthvaluecm read-only
This attribute controls whether the SSID will be advertised in beacon frames. If it is dot11true, the SSID will not be advertised in beacon frames.
                 hpnicfDot11SPIsolateCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.27 hpnicfdot11truthvaluecm read-only
If it is dot11true, the clients connected with the service policy are isolated to each other.
         hpnicfDot11ServicePolicyExtTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3 no-access
The table defines the parameters for ESS, as per service policy of CLI. When the value of hpnicfDot11SSIDEncryptionMode equals to cipher(2), more configuration for a ESS will be put into the table.
             hpnicfDot11ServicePolicyExtEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1 no-access
Each entry contains information of each service policy under cipher(2) mode.
                 hpnicfDot11ServicePolicyExtID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.1 hpnicfdot11servicepolicyidtype no-access
Represents the ID of each service policy.
                 hpnicfDot11SecIEStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.2 hpnicfdot11seciestatustype read-only
To enable the security Information element in the beacon and probe response frames sent by AP.
                 hpnicfDot11SecurityCiphers 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.3 integer32 read-only
The WLAN system support the following cipher type for data frame encryption. wep40(2) tkip(4) aesccmp(16) wep104(32) wpisms4(64) wep128(128) For each service policy, it could support multiple cipher types at the same time. So the value of object could combine multiple value of cipher type above. When the value of node equals to zero, it means no configuration or undo operation.
                 hpnicfDot11CipherKeyIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.4 integer32 read-only
Represents the key index of cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
                 hpnicfDot11CipherKey 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.5 octet string read-only
Represents the cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
                 hpnicfDot11SrvPolicyExtRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.6 rowstatus read-only
The status of this table entry.
                 hpnicfDot11CipherKeyType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.7 integer read-only
Represents the cipher key type of hpnicfDot11CipherKey. Enumeration: 'char': 1, 'hex': 2.
         hpnicfDot11RadioPolicyExtTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4 no-access
The table defines the radio policy of each radio. It can't be modified if the radio policy is a default radio policy.
             hpnicfDot11RadioPolicyExtEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1 no-access
Each entry contains information of each radio policy.
                 hpnicfDot11RPAPSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.1 octet string no-access
This object represents the Serial ID of AP.
                 hpnicfDot11RPRadioID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.2 hpnicfdot11radioscopetype no-access
This object represents each radio.
                 hpnicfDot11RPBeaconInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.3 integer32 read-write
This object represents the interval for Beacon management frame.
                 hpnicfDot11RPDtimInterval 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.4 integer32 read-write
This object represents the number of beacon intervals that shall elapse between transmissions of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
                 hpnicfDot11RPRtsThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.5 integer32 read-write
This object represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
                 hpnicfDot11RPFragThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.6 integer32 read-write
This object represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
                 hpnicfDot11RPShortRetryThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.7 integer32 read-write
This object represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated.
                 hpnicfDot11RPLongRetryThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.8 integer32 read-write
This object represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, and that shall be made before a failure condition is indicated.
                 hpnicfDot11RPClientMaxCount 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.9 integer32 read-write
This object represents the maximum number of stations supported by this radio policy.
                 hpnicfDot11RPBeaconIntervalCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.10 integer32 read-write
This object represents beacon interval.
         hpnicfDot11SrvPortSecurityTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5 no-access
This table defines the WLAN security status for ESS, BSS and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security.
             hpnicfDot11SrvPortSecurityEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1 no-access
There is a row in this table for service policy.
                 hpnicfDot11SecurityServicePolicyID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.1 hpnicfdot11servicepolicyidtype no-access
Represents the ID of each service policy.
                 hpnicfDot11SrvPortSecurityMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.2 integer read-write
Determines the security modes of the WLAN port. noRestrictions The default value, no any security mode is set. userLoginSecureExt Access to the port is denied until the port client is authorized (by 802.1X). psk Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext Access to the port is denied until the port client is authenticated (by ext). Enumeration: 'userLoginSecureExtOrPsk': 5, 'psk': 3, 'macAddressAndPsk': 4, 'ext': 6, 'noRestrictions': 1, 'userLoginSecureExt': 2.
                 hpnicfDot11SrvSecurityKeyType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.3 integer read-write
This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption. Enumeration: 'userLoginTxKeyTypeNone': 1, 'userLoginTxKeyTypeRsaRC4Key': 3, 'userLoginTxKeyTypeDot11Key': 2.
                 hpnicfDot11SrvSecurityPskKeyMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.4 integer read-write
This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SrvSecurityPskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SrvSecurityPskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'. Enumeration: 'pskKeyModeRawKey': 3, 'pskKeyModePassPhrase': 2, 'pskKeyModeNone': 1.
                 hpnicfDot11SrvSecurityPskKeyString 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.5 displaystring read-write
This is the password string used for psk authentication.
                 hpnicfDot11SrvPortSecurityModeCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.6 integer read-write
Determines the security modes of the WLAN port. none - The default value, no any security mode is set. psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). radius - Access to the port is denied until the port client is authorized (by 802.1X). wlanex - Access to the port is denied until the port client is authenticated by wlan cert. Enumeration: 'psk': 1, 'none': 0, 'radius': 2, 'wlanex': 3.
         hpnicfDot11SrvPolicyExtendTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6 no-access
The table defines the parameters of each service policy.
             hpnicfDot11SrvPolicyExtendEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1 no-access
Each entry contains information of each service policy.
                 hpnicfDot11SPEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1.1 integer read-write
Represents whether the service policy is enabled. Enumeration: 'enable': 1, 'disable': 2.
     hpnicfDot11APConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3
         hpnicfDot11APTemplateTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1 no-access
By AP template CLI, administrator will configure the parameters of AP by convenience. Before AP boot up and connect to AC by CAPWAP tunnel, administrator will create AP template for each AP. When AP connect to AC, AC will assign configuration to AP by hpnicfDot11APSerialID information in AP template.
             hpnicfDot11APTemplateEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1 no-access
Each entry contains configuration information for each AP.
                 hpnicfDot11APTemplateName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.1 octet string no-access
Represents the name of AP template.
                 hpnicfDot11APSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.2 octet string read-only
Represents AP serial id.
                 hpnicfDot11TemplateAPModelAlias 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.3 octet string read-only
Represents the alias of AP model name.
                 hpnicfDot11Description 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.4 octet string read-only
This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
                 hpnicfDot11APWorkMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.5 integer read-only
Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. Enumeration: 'hybrid': 3, 'monitor': 2, 'normal': 1.
                 hpnicfDot11APTemplateRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.6 rowstatus read-only
The status of this table entry.
                 hpnicfDot11APName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.7 octet string read-only
Represents the AP name.
                 hpnicfDot11StatisInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.8 integer32 read-only
Represents the interval of radio statistic.
                 hpnicfDot11APBroadcastProbeReply 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.9 truthvalue read-only
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
                 hpnicfDot11StaIdleTimerInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.10 integer32 read-only
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
                 hpnicfDot11StaKeepAliveTimerInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.11 integer32 read-only
Represents the interval of the keep alive requests sent between AP and STA.
                 hpnicfDot11APCir 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.12 integer32 read-only
Represents the committed information rate between AP and AC.
                 hpnicfDot11APCbs 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.13 integer32 read-only
Represents the committed burst size between AP and AC.
                 hpnicfDot11APPriorityLevel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.14 integer32 read-only
This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
                 hpnicfDot11APElementID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.15 integer32 read-only
This object represents the AP element ID.
                 hpnicfDot11APDevDetectEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.16 truthvalue read-only
Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11APDevDetectEnable.
                 hpnicfDot11APGetIPMethod 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.17 integer read-only
This object represents the method how AP gets IP address. Enumeration: 'static': 2, 'dhcpAlloc': 1.
                 hpnicfDot11StatisIntervMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.18 integer read-only
This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s Enumeration: 'realtime': 2, 'normal': 1.
                 hpnicfDot11ApTrapEnabled 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.19 truthvalue read-write
Represents whether the trap status is enabled or not. 'true' : Enable the trap status; 'false' : Disable the trap status.
                 hpnicfDot11ApFmwUpdState 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.20 integer read-only
Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. inherit - The status will inherit value from apgroup-view or system-view. Enumeration: 'enable': 1, 'inherit': 3, 'disable': 2.
                 hpnicfDot11StatisIntervModeCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.21 integer read-only
This object represents the mode of statistic interval. off - statistic interval value between 10s to 120s on - statistic interval value between 2s to 5s Enumeration: 'on': 1, 'off': 0.
                 hpnicfDot11ApNasIDCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.22 octet string read-only
Represents the NAS-ID of current service policy for each specific radio of AP.
         hpnicfDot11RadioToConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2 no-access
Before AP connects to AC, administrator will configure radio parameter to each radio.
             hpnicfDot11RadioToConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1 no-access
Each entry contains configuration information for each radio.
                 hpnicfDot11APTemplateNameCfg 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.1 octet string no-access
Represents the name of AP template.
                 hpnicfDot11CfgRadioID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.2 hpnicfdot11radioscopetype no-access
Represents each radio.
                 hpnicfDot11CfgRadioPolicyName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.3 octet string read-write
Represents the name of radio policy.
                 hpnicfDot11CfgRadioType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.4 hpnicfdot11radiotype read-write
Represents the radio will work with which 802.11 radio type.
                 hpnicfDot11CfgChannel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.5 hpnicfdot11channelscopetype read-write
Represents the channel allocation of radio.
                 hpnicfDot11CfgMaxTxPowerLevel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.6 hpnicfdot11txpwrlevelscopetype read-write
Represents the maximal transmit power scope for AP.
                 hpnicfDot11PreambleLen 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.7 hpnicfdot11preambletype read-write
Represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid.
                 hpnicfDot11CfgRadioStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.8 truthvalue read-write
Represents the radio admin status whether is enabled or disabled.
                 hpnicfDot11CfgRdElementID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.9 unsigned32 read-only
Represents the element ID of this radio. It comprises two parts. The highest 24 bits are AP element ID and the lowest 8 bits are radio ID.
                 hpnicfDot11CfgWorkMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.10 hpnicfdot11workmode read-write
Represents work mode of the radio.
                 hpnicfDot11CfgPwrAttValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.11 integer32 read-write
Represents the value of power attenuation.
                 hpnicfDot11RadioTxArithmetic 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.12 integer read-write
Represents the transmission arithmetic of the radio. The following values are supported: quality - Consider the quality first during the transmission. bandwidth - Consider the bandwidth first during the transmission. Enumeration: 'bandwidth': 2, 'quality': 1.
                 hpnicfDot11CfgChannelLockStat 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.13 integer read-write
Represents locked status of channel on the radio. Enumeration: 'locked': 2, 'unlocked': 1.
                 hpnicfDot11CfgPowerLockStat 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.14 integer read-write
Represents locked status of power on the radio. Enumeration: 'locked': 2, 'unlocked': 1.
                 hpnicfDot11CfgLBRdGroupId 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.15 unsigned32 read-write
Represents the load balance group ID allocated for the radio.
                 hpnicfDot11CfgRRMSDRdGroupId 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.16 unsigned32 read-write
Represents the RRM self-decisive group ID allocated for the radio.
                 hpnicfDot11CfgRadioType2 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.17 hpnicfdot11radiotype2 read-write
Represents the radio will work with which 802.11 radio type.
                 hpnicfDot11CfgIDSEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.18 truthvalue read-write
Represents whether intrusion detection is enabled for this radio.
                 hpnicfDot11CfgSaEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.19 truthvalue read-write
Represents whether spectrum analysis is enabled.
                 hpnicfDot11CfgSaCltRtFFTData 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.20 truthvalue read-write
Represents whether to collect real-time FFT data for this radio.
                 hpnicfDot11CfgSaBand 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.21 integer read-write
Represents which band of channels will be monitored when collection real-time FFT data is enabled for this radio. Detection of interference devices and air quality will also be affected. Each band responds to the following channels. dot11g (Channels 1-14) dot11aLower (channels 36-64) dot11aMiddle (channels 100-140) dot11aUpper (channels 149-165). Enumeration: 'dot11g': 1, 'dot11aMiddle': 3, 'dot11aLower': 2, 'dot11aUpper': 4.
         hpnicfDot11APServiceSetTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3 no-access
For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
             hpnicfDot11APServiceSetEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1 no-access
Each entry contains service policy information for each specific radio of AP.
                 hpnicfDot11CfgServicePolicyID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.1 hpnicfdot11servicepolicyidtype no-access
Represents the ID of each service policy used by the AP.
                 hpnicfDot11SrvSetRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.2 rowstatus read-only
The status of this table entry.
                 hpnicfDot11ServiceSetVlanId 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.3 integer32 read-only
Represents the Vlan ID of BSS which is generated when service policy is binded with the Radio.
         hpnicfDot11APSysInfoSetTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4 no-access
The table of the system information for each AP.
             hpnicfDot11APSysInfoSetEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1 no-access
The system information configuration for each AP.
                 hpnicfDot11APSysNetID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.1 octet string read-write
Represents the system Net ID for AP.
                 hpnicfDot11APCpuUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.2 integer32 read-write
The CPU usage threshold for AP.
                 hpnicfDot11APMemUsageThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.3 integer32 read-write
The memory usage threshold for AP.
         hpnicfDot11APLimitTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5 no-access
For each connected APs, administrator could configure a series of limits. This table describes the limit information for AP(s).
             hpnicfDot11APLimitEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1 no-access
Each entry contains the limit information for each AP.
                 hpnicfDot11APSsidNumLimit 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.1 integer32 read-write
Represents the upper limit of service template binded with this AP. All radios of AP share this limit. Default value 0 : There is no upper limit of service template binded with this AP.
                 hpnicfDot11APUserCntLimit 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.2 integer32 read-write
Represents the upper limit of user which has access to this AP. All BSSs binded with AP share this limit. Default value 0 : There is no upper limit of user which has access to this AP.
                 hpnicfDot11APUserThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.3 integer32 read-write
Represents the threshold of user which has access to this AP. All BSSs binded with AP share this limit. If the user counter is overflow, the trap will be sent. Default value 0 : There is no threshold of user which has access to this AP.
         hpnicfDot11APIfSetTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6 no-access
The table of the interface information for each AP.
             hpnicfDot11APIfSetEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1 no-access
The interface information configuration for each AP.
                 hpnicfDot11APSetIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.1 integer32 no-access
Represents the index for a interface.
                 hpnicfDot11APIfAlias 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.2 displaystring read-write
This object is an 'alias' name for the interface as specified by a network manager for AP.
         hpnicfDot11APServiceVlanTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7 no-access
For all the radios on the AP, it could configure multiple service policies. The table describes the relationship between AP and service policies.
             hpnicfDot11APServiceVlanEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1 no-access
Each entry contains service policy information for each AP.
                 hpnicfDot11APServiceVlanSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.1 octet string no-access
This object represents AP serial id.
                 hpnicfDot11APServiceVlanSPID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.2 hpnicfdot11servicepolicyidtype no-access
This object represents the ID of each service policy used by the AP.
                 hpnicfDot11APServiceVlanId 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.3 integer32 read-only
This object represents the VLAN ID of BSS which is generated when the service policy is bound to the radio.
                 hpnicfDot11APServiceVlanRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.4 rowstatus read-only
This object represents the status of this table entry.
         hpnicfDot11RadioConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8 no-access
Before AP connects to AC, administrator will configure radio parameter to each radio.
             hpnicfDot11RadioConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1 no-access
Each entry contains configuration information for each radio.
                 hpnicfDot11RCAPSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.1 octet string no-access
This object represents the Serial ID of AP.
                 hpnicfDot11RCRadioID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.2 hpnicfdot11radioscopetype no-access
This object represents each radio.
                 hpnicfDot11RCRadioType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.3 hpnicfdot11radiotype read-write
This object represents the radio will work with which 802.11 radio type.
                 hpnicfDot11RCChannel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.4 hpnicfdot11channelscopetype read-write
This object represents the channel allocation of radio.
                 hpnicfDot11RCPreambleLen 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.5 hpnicfdot11preambletype read-write
This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid.
                 hpnicfDot11RCPwrAttValue 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.6 integer32 read-write
This object represents the value of power attenuation.
                 hpnicfDot11RCApPowerLevel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.7 hpnicfdot11txpwrlevelscopetype read-write
Represents the maximal transmit power scope for AP.
                 hpnicfDot11RCDynamicChlState 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.8 truthvalue read-write
Enable/Disable dynamic channel selection.
                 hpnicfDot11RCDynamicPowerState 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.9 truthvalue read-write
Enable/Disable dynamic power selection for the band.
                 hpnicfDot11RCRadioStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.10 truthvalue read-write
Represents the radio admin status whether is enabled or disabled.
                 hpnicfDot11RCRadioRate 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.11 octet string read-write
Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format can be MCS X. The data transmit rates between AP and STA must fall into the configured rates. (Note: For 802.11n radios, the first value will be treated as a mandatory rate, and the second value will be treated as a supported rate. If you configure more than two rates, the configuration cannot take effect. If you configure only one rate, it is considered as the mandatory rate by default.)
                 hpnicfDot11RCPwrAdjustStepLength 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.12 integer32 read-only
Power adjustment step-length in dBm.
                 hpnicfDot11RCRadioType2 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.13 hpnicfdot11radiotype2 read-write
This object represents the radio will work with which 802.11 radio type.
                 hpnicfDot11RCPreambleLenCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.14 integer read-write
This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLenCM will be valid. Otherwise, the value for it will be invalid. Enumeration: 'short': 1, 'long': 0.
                 hpnicfDot11RCDynamicChlStateCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.15 integer read-write
Enable/Disable dynamic channel selection. Enumeration: 'on': 1, 'off': 0.
                 hpnicfDot11RCRadioStatusCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.16 integer read-write
Represents the radio admin status whether is enabled or disabled. Enumeration: 'down': 2, 'testing': 3, 'up': 1.
                 hpnicfDot11RCRadioRateCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.17 octet string read-write
Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format of each value can be MCS X. The data transmit rates between AP and client should be one of the configured rates. (Note: For 802.11n radios, the first value is mandatory rate, and the second value is supported rate. If more than two rate values are configured, the configuration will not take effect. If only one rate value is configured, the mandatory rate will be set to the default value.)
                 hpnicfDot11RCDynamicPowerStateCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.18 hpnicfdot11truthvaluecm read-write
Enable/disable dynamic power selection for the band.
         hpnicfDot11RadioSSIDCfgTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9 no-access
For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
             hpnicfDot11RadioSSIDCfgEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1 no-access
Each entry contains SSID configuration information for each radio.
                 hpnicfDot11RadioSSIDSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.1 hpnicfdot11objectidtype no-access
This object represents the serial ID of AP.
                 hpnicfDot11RadioSSIDRadioID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.2 hpnicfdot11radioscopetype no-access
This object represents each radio.
                 hpnicfDot11RadioSSIDWLANID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.3 integer32 no-access
This object represents the WLAN ID of the BSSID.
                 hpnicfDot11RadioSSIDIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.4 hpnicfdot11servicepolicyidtype read-only
This object represents the ID of each service policy used by the radio.
                 hpnicfDot11RadioBSSID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.5 macaddress read-only
As MAC address format, it is used to identify BSS.
                 hpnicfDot11RadioSSIDRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.6 rowstatus read-only
RowStatus.
         hpnicfDot11APSerialIDTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10 no-access
The table will provide the general information about APs.
               hpnicfDot11APSerialIDEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1 no-access
Each entry contains the general information of an AP.
                   hpnicfDot11SIDAPSerialID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.1 octet string no-access
Represents AP serial id.
                   hpnicfDot11SIDAPWorkMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.2 integer read-only
Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. Enumeration: 'hybrid': 3, 'monitor': 2, 'normal': 1.
                   hpnicfDot11SIDAPGetIPMethod 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.3 integer read-only
This object represents the method how AP gets IP address. Enumeration: 'static': 2, 'dhcpAlloc': 1.
                   hpnicfDot11SIDAPTemplateName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.4 octet string read-only
Represents the name of AP template.
                   hpnicfDot11SIDModelAlias 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.5 octet string read-only
Represents the alias of AP model name.
                   hpnicfDot11SIDAPDescription 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.6 octet string read-only
This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
                   hpnicfDot11SIDRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.7 rowstatus read-only
The status of this table entry.
                   hpnicfDot11SIDAPName 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.8 octet string read-only
Represents the AP name.
                   hpnicfDot11SIDStatisInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.9 integer32 read-only
Represents the interval of radio statistic.
                   hpnicfDot11SIDAPBroadcastProbeReply 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.10 truthvalue read-only
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
                   hpnicfDot11SIDAPStaIdleTimerInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.11 integer32 read-only
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
                   hpnicfDot11SIDStaKeepAliveTimerInterv 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.12 integer32 read-only
Represents the interval of the keep alive requests sent between AP and STA.
                   hpnicfDot11SIDAPCir 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.13 integer32 read-only
Represents the committed information rate between AP and AC.
                   hpnicfDot11SIDAPCbs 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.14 integer32 read-only
Represents the committed burst size between AP and AC.
                   hpnicfDot11SIDAPPriorityLevel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.15 integer32 read-only
This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
                   hpnicfDot11SIDAPElementID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.16 integer32 read-only
This object represents the AP element ID.
                   hpnicfDot11SIDAPDevDetectEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.17 truthvalue read-only
Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11SIDAPDevDetectEnable.
                   hpnicfDot11SIDAPStatisIntervMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.18 integer read-only
This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s Enumeration: 'realtime': 2, 'normal': 1.
                   hpnicfDot11SIDAPWorkModeCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.19 integer read-only
Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. SemiMonitor - AP will supply WLAN service and Device detection is enabled. Enumeration: 'semimonitor': 2, 'monitor': 1, 'normal': 0.
         hpnicfDot11APSTVlanTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11 no-access
For each service policy, it could be bind to several VLANs. The table describes the relationship between VLAN and service policies.
               hpnicfDot11APSTVlanEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1 no-access
Each entry contains VLAN and service policy information for each specific radio of AP.
                   hpnicfDot11CfgSTVLANID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.1 integer32 read-only
Represents the VLAN that current Service Policy have bind to.
                   hpnicfDot11CfgSTNASPortID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.2 octet string read-only
Represents the NAS Port ID of current Service Policy for each specific radio of AP.
                   hpnicfDot11CfgServiceSetRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.3 rowstatus read-only
The status of this table entry.
                   hpnicfDot11CfgSTNASID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.4 octet string read-only
Represents the NAS ID of current Service Policy for each specific radio of AP.
     hpnicfDot11RadioIntfConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4
         hpnicfDot11RadioIntfConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1 no-access
The table defines the parameters for radio in AP, as per radio.
             hpnicfDot11RadioIntfConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1 no-access
Each entry contains information of each radio in AP.
                 hpnicfDot11RadioIfIdx 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.1 integer32 no-access
Represents the Radio IfIndex of radio in AP.
                 hpnicfDot11RadioCfgBeaconIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.2 integer32 read-write
Represents the interval for Beacon management frame.
                 hpnicfDot11RadioCfgDtimIntvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.3 integer32 read-write
Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
                 hpnicfDot11RadioCfgRtsThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.4 integer32 read-write
Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
                 hpnicfDot11RadioCfgFragThreshold 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.5 integer32 read-write
Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
                 hpnicfDot11RadioCfgShtRetryThld 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.6 integer32 read-write
Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
                 hpnicfDot11RadioCfglongRtrThld 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.7 integer32 read-write
Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
                 hpnicfDot11RadioCfgMaxRxLifetime 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.8 unsigned32 read-write
Represents the elapsed time. After the time specified by hpnicfDot11RadioCfgMaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
                 hpnicfDot11RadioCfgType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.9 hpnicfdot11radiotype read-write
Represents the radio will work with which 802.11 radio type.
                 hpnicfDot11RadioCfgChannel 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.10 hpnicfdot11channelscopetype read-write
Represents the channel allocation of radio.
                 hpnicfDot11RadioCfgMaxTxPwrLvl 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.11 hpnicfdot11txpwrlevelscopetype read-write
Represents the maximal transmit power scope for AP.
                 hpnicfDot11RadioCfgPreambleLen 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.12 hpnicfdot11preambletype read-write
Represents whether use long or short preamble for 802.11 MAC frame.
                 hpnicfDot11RadioCfgWorkMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.13 hpnicfdot11workmode read-write
Represents work mode of the radio.
                 hpnicfDot11RadioCfgOnly11gEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.14 truthvalue read-write
Represents whether enable only 802.11g radio mode or not. 'true' : Only 802.11g radio mode is enabled. 'false': Only 802.11g radio mode is disabled.
                 hpnicfDot11RadioCfgType2 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.15 hpnicfdot11radiotype2 read-write
Represents the radio will work with which 802.11 radio type.
                 hpnicfDot11RadioCfgRssithresholdCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.16 integer32 read-write
Represents the minimum value of the RSSI. The clients with RSSI below this value will be refused to associate.
         hpnicfDot11RadioIntfBindTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2 no-access
The table defines the binding information for each radio in AP.
             hpnicfDot11RadioIntfBindEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1 no-access
Each entry contains the radio interface binding information in AP.
                 hpnicfDot11RadioIntfBindSvcPlcyID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.1 hpnicfdot11servicepolicyidtype no-access
Represents the ID of each service policy.
                 hpnicfDot11RadioIntfBindIfIdx 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.2 unsigned32 read-only
Represents the Ifindex of interface which is binded to the radio.
                 hpnicfDot11RadioIntfBindRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.3 rowstatus read-only
The status of this table entry.
     hpnicfDot11DataRateConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5
         hpnicfDot11DataRateConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1 no-access
Table will provide data rate configuration for a specific radio type.
             hpnicfDot11DataRateConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1 no-access
Each entry of the table will provide data rate configuration for a specific radio type.
                 hpnicfDot11RadioTypeID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.1 hpnicfdot11radiotype no-access
Represents the radio type.
                 hpnicfDot11SupportedRateSet 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.2 octet string read-write
Represents the supported rate set of a particular radio type.
                 hpnicfDot11MandatoryRateSet 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.3 octet string read-write
Represents the mandatory rate set of a particular radio type.
                 hpnicfDot11DisabledRateSet 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.4 octet string read-write
Represents the disabled rate set of a particular radio type.
                 hpnicfDot11SmartRateSet 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.5 octet string read-write
Represents the rate set of a particular radio type.
     hpnicfDot11InterfaceConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6
         hpnicfDot11WlanEssIfTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1 no-access
This table is used to configure WLAN ESS interface.
             hpnicfDot11WlanEssIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1 no-access
Each entry contains the WLAN ESS interface configuration.
                 hpnicfDot11WlanEssIfNumber 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.1 integer32 no-access
This node represents the WLAN ESS interface number.
                 hpnicfDot11WlanEssIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.2 integer32 read-only
This node represents the ifIndex of WLAN-ESS interface.
                 hpnicfDot11WlanEssRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.3 rowstatus read-only
This node represents the WLAN ESS interface row status.
         hpnicfDot11WlanBssIfTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2 no-access
This table is used to configure WLAN BSS interface.
             hpnicfDot11WlanBssIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1 no-access
Each entry contains the WLAN BSS interface configuration.
                 hpnicfDot11WlanBssIfNumber 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.1 integer32 no-access
This node represents the WLAN BSS interface number.
                 hpnicfDot11WlanBssIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.2 integer32 read-only
This node represents the ifIndex of WLAN-BSS interface.
                 hpnicfDot11WlanBssRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.3 rowstatus read-only
This node represents the WLAN BSS interface row status.
         hpnicfDot11WLANEthernetIfTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3 no-access
This table is used to configure WLAN Ethernet interface.
             hpnicfDot11WLANEthernetIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1 no-access
Each entry contains the WLAN Ethernet interface configuration.
                 hpnicfDot11WlanEthernetIfNumber 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.1 integer32 no-access
This node represents the WLAN Ethernet interface number.
                 hpnicfDot11WLANEthernetIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.2 integer32 read-only
This node represents the ifIndex of WLAN-Ethernet interface.
                 hpnicfDot11WlanEthernetRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.3 rowstatus read-only
This node represents the Wlan Ethernet interface row status.
         hpnicfDot11PortSecurityTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4 no-access
This table defines the WLAN security status for ESS, BSS, mesh and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security.
             hpnicfDot11PortSecurityEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1 no-access
There is a row in this table for each ESS, BSS and WLAN-Ethernet interface.It is indexed using the object ifIndex in RFC1213-MIB.
                 hpnicfDot11PortSecurityMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.1 integer read-write
Determines the security modes of the WLAN port. noRestrictions - The default value,no any security mode is set. userLoginSecureExt - Access to the port is denied until the port client is authorized (by 802.1X). psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk - The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext - Access to the port is denied until the port client is authenticated (by ext). Enumeration: 'userLoginSecureExtOrPsk': 5, 'psk': 3, 'macAddressAndPsk': 4, 'ext': 6, 'noRestrictions': 1, 'userLoginSecureExt': 2.
                 hpnicfDot11SecurityUserLoginTxKeyType 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.2 integer read-write
This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption. Enumeration: 'userLoginTxKeyTypeNone': 1, 'userLoginTxKeyTypeRsaRC4Key': 3, 'userLoginTxKeyTypeDot11Key': 2.
                 hpnicfDot11SecurityPskKeyMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.3 integer read-write
This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SecurePskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SecurePskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'. Enumeration: 'pskKeyModeRawKey': 3, 'pskKeyModePassPhrase': 2, 'pskKeyModeNone': 1.
                 hpnicfDot11SecurityPskKeyString 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.4 displaystring read-write
This is the password string used for psk authentication.
         hpnicfDot11WlanMeshIfTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5 no-access
This table is used to configure WLAN mesh interface.
             hpnicfDot11WlanMeshIfEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1 no-access
Each entry contains the WLAN mesh interface configuration.
                 hpnicfDot11WlanMeshIfNumber 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.1 integer32 no-access
This node represents the WLAN mesh interface number.
                 hpnicfDot11WlanMeshIfIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.2 integer32 read-only
This node represents the index of WLAN mesh interface.
                 hpnicfDot11WlanMeshRowStatus 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.3 rowstatus read-only
This node represents the WLAN mesh interface row status.
     hpnicfDot11ACBackupGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7
         hpnicfDot11BackupACAdrssIP 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.1 inetaddress read-write
This object represents the backup AC IP address. If the backup AC IP address is not configured, the object value is 0.0.0.0.
         hpnicfDot11BackupACAdrssIPv6 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.2 inetaddress read-write
This object represents the backup AC IPv6 address. If the backup AC IPv6 address is not configured, the object value is 0::0.
     hpnicfDot11RadioElementConfigGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8
         hpnicfDot11nRadioCfgTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1 no-access
This table is used to configure dot11n on the radio.
             hpnicfDot11nRadioCfgEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1 no-access
This entry contains the dot11n configuration on the radio.
                 hpnicfDot11nRadioCfgIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.1 hpnicfdot11radioelementindex no-access
Represents index of the radio.
                 hpnicfDot11nAMpduEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.2 truthvalue read-write
Enable the function of A-MPDU.
                 hpnicfDot11nAMsduEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.3 truthvalue read-write
Enable the function of A-MSDU.
                 hpnicfDot11nClientDot11nOnly 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.4 truthvalue read-write
If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode.
                 hpnicfDot11nChanelBand 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.5 integer read-write
Specify the bandwidth mode. Enumeration: 'mode40': 2, 'mode20': 1, 'mode80': 3.
                 hpnicfDot11nShortGiEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.6 truthvalue read-write
The function of Short GI.
                 hpnicfDot11nClientDot11acOnly 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.7 truthvalue read-write
Only permit clients of 11ac mode.
         hpnicfDot11RadioWDSTable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2 no-access
This table is used to configure WDS on the radio.
             hpnicfDot11RadioWDSEntry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1 no-access
Each entry contains the WDS configuration on the radio.
                 hpnicfDot11RadioWDSIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.1 hpnicfdot11radioelementindex no-access
Represents the element index of radio.
                 hpnicfDot11RadioWDSMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.2 integer read-write
Represents enable the WDS mode or not. nowds: The WDS mode is disabled. wds : The WDS mode is enabled Enumeration: 'nowds': 1, 'wds': 2.
                 hpnicfDot11RadioWDSNetWorkID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.3 octet string read-write
Represents the mesh ID of WDS.
                 hpnicfDot11WDSSecPskKeyMode 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.4 integer read-write
Represents the PSK mode of WDS. Enumeration: 'pskKeyModeRawKey': 3, 'pskKeyModePassPhrase': 2, 'pskKeyModeNone': 1.
                 hpnicfDot11WDSSecPskKeyString 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.5 displaystring read-write
Represents the PSK value of WDS.
         hpnicfDot11nRadioCfg2Table 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3 no-access
This table is used to configure dot11n on the radio.
             hpnicfDot11nRadioCfg2Entry 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1 no-access
This entry contains the dot11n configuration on the radio.
                 hpnicfDot11nRadioCfg2APIDIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.1 hpnicfdot11objectidtype no-access
Represents index of the AP.
                 hpnicfDot11nRadioCfg2RadioIDIndex 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.2 hpnicfdot11radioscopetype no-access
Represents index of the radio.
                 hpnicfDot11nRadioCfg2AMpduEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.3 truthvalue read-write
Enable the function of A-MPDU.
                 hpnicfDot11nRadioCfg2AMsduEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.4 truthvalue read-write
Enable the function of A-MSDU.
                 hpnicfDot11nRadioCfg2ClientDot11nOnly 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.5 truthvalue read-write
If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode.
                 hpnicfDot11nRadioCfg2ChannelBand 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.6 integer read-write
Specify the bandwidth mode. Enumeration: 'mode40': 2, 'mode20': 1, 'mode80': 3.
                 hpnicfDot11nRadioCfg2ShortGiEnable 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.7 truthvalue read-write
Enable the function of Short GI.
                 hpnicfDot11nRadioCfg2AMpduEnableCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.8 integer read-write
Enable the function of A-MPDU. Enumeration: 'on': 1, 'off': 0.
                 hpnicfDot11nRadioCfg2ChannelBandCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.9 integer read-write
Specify the bandwidth mode. Enumeration: 'mode40': 1, 'mode20': 2.
                 hpnicfDot11nRadioCfg2ShortGiEnableCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.10 integer read-write
Enable the function of Short GI. Enumeration: 'on': 1, 'off': 0.
                 hpnicfDot11nRadioCfg2ClientDot11acOnly 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.11 truthvalue read-write
Only permit clients of 11ac mode.
                 hpnicfDot11nRadioCfg2ClientDot11nOnlyCM 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.12 hpnicfdot11truthvaluecm read-write
If radio type is 802.11an or 802.11gn, permit only clients of 11n mode. If radio type is 802.11ac, permit clients of both 11n and 11ac mode.
     hpnicfDot11CfgNotifyGroup 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9
         hpnicfDot11CfgNotifications 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0
             hpnicfDot11CfgCipherChange 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.1
This notification is sent when cipher type of corresponding service template is changed.
             hpnicfDot11CfgPSKChange 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.2
This notification is sent when pre-shared key of corresponding service template is changed.
             hpnicfDot11SSIDWepIDConflictTrap 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.3
This notification will be sent when the same wep ID is configured on two service policies.
         hpnicfDot11CfgTrapVarObjects 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1
             hpnicfDot11PreConflictTemplateNum 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.1 integer32 no-access
Represents previous service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
             hpnicfDot11CurrConflictTemplateNum 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.2 integer32 no-access
Represents current service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
             hpnicfDot11ConflictCipherIdx 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.3 integer32 no-access
Represents wep ID that conflicted with.
             hpnicfDot11ConfigureAPID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.4 hpnicfdot11objectidtype no-access
Represents which AP is configured.
             hpnicfDot11ConfigureRadioID 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.5 hpnicfdot11radioscopetype no-access
Represents which radio in AP is configured.
             hpnicfDot11ConfigureAPMacAddress 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.6 macaddress no-access
Represents MAC Address of AP.