E5-121-MIB: View SNMP OID List / Download MIB

The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff

This table includes alarm configuration.

An entry in alarmConfTable.

5000:vdslLine_up 5001:vdslLine_down 5002:vdsl_tca_lol 5003:vdsl_tca_lof 5004:vdsl_tca_los 5005:vdsl_tca_lop 5006:vdsl_tca_es 5007:vdsl_tca_ses 5008:vdsl_tca_uas 5009:xd_xtuc_loftrap 5010:xd_xtuc_lostrap 5011:xd_xtur_loftrap 5012:xd_xtur_lostrap 5013:xd_xtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:voip_battery_fail 10009:voip_clock_fail 10010:voip_ringer_fault 10011:eqptAlm_input2 10012:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 15006:sysHost_terminate 20000:enetUp 20001:enetDown 25000:voip_temp_error 25001:voip_dc_power_fail 25002:voip_ac_power_fail 25003:voip_ring_timer_fail 25004:voip_ring_rsrce_fail 25006:voip_dhcp_clt_fail 25007:voip_call_setup_failed 25008:voip_call_threshold_violate 30000:cfmError

Alarm facility. Enumeration: 'local5': 5, 'local4': 4, 'local7': 7, 'local6': 6, 'local1': 1, 'local3': 3, 'local2': 2.

The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog

Alarm severity Enumeration: 'info': 4, 'major': 2, 'critical': 1, 'minor': 3.

Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear. Enumeration: 'clearable': 1, 'unclearable': 2.

This table includes current alarm information.

An entry in alarmCurrTable.

Index of the alarm.

Alarm occurence time (in hundredths of a second) since the system was last re-initialized.

Trap OID of the alarm.

The 1st parameter of the alarm.

The 2nd parameter of the alarm.

The 3rd parameter of the alarm.

The 4th parameter of the alarm.

The 5th parameter of the alarm.

The 6th parameter of the alarm.

The 7th parameter of the alarm.

The 8th parameter of the alarm.

The string representation of occurence time (YYYY/MM/DD HH:MM:SS).

The severity of the alarm. Enumeration: 'info': 4, 'major': 2, 'critical': 1, 'minor': 3.

The description of the alarm.

This table includes the configuration of alarm reporting severity threshold for each port.

An entry in alarmSeverityPortTable.

The minimum alarm severity that is reported. Enumeration: 'info': 4, 'major': 2, 'critical': 1, 'minor': 3.

IfIndex of the port which would be performed single end loopback test.

The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.

Status description of the selt result.

The cable type that selt result indicates. Enumeration: 'awg24': 1, 'awg26': 2.

The estimated loop length that selt result indicates.

The estimated loop length that selt result indicates.

IfIndex of the port which would be performed ldm test.

The manager sets the object to 1 to start the ldm test and the agent clears the object to zero when ldm test is successfully completed.

Status description of ldm test result.

Loop Attenuation.

Signal Attenuation.

Signal Margin.

Actual Aggregate Transmit Power.

Attainable Bit Rate.

Loop Attenuation.

Signal Attenuation.

Signal Margin.

Actual Aggregate Transmit Power.

Attainable Bit Rate.

The number of subcarriers per port for ATU-C.

The number of subcarriers per port for ATU-R.

Scale of Hlin.

The object provides real part of Hlin for the first 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides real part of Hlin for the last 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides image part of Hlin for the first 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides image part of Hlin for the last 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides Hlog for the first 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides Hlog for the last 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides QLN for the first 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides QLN for the last 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides SNR for the first 256 subcarriers. Each subcarrier takes two octets to store the value.

The object provides SNR for the last 256 subcarriers. Each subcarrier takes two octets to store the value.

Scale of Hlin.

Real part of Hlin. Each subcarrier takes two octets to store the value.

Image part of Hlin. Each subcarrier takes two octets to store the value.

Hlog of subcarrier. Each subcarrier takes two octets to store the value.

QLN of subcarrier. Each subcarrier takes two octets to store the value.

SNR of subcarrier. Each subcarrier takes two octets to store the value.

The Hlog group factor of ATU-C.

The Qln group factor of ATU-C.

The Snr group factor of ATU-C.

The Hlog group factor of ATU-R.

The Qln group factor of ATU-R.

The Snr group factor of ATU-R.

IfIndex of the port which would be performed Metallic Link Test.

The manager sets the object to 1 to start the mlt and the agent clears the object to zero when mlt is successfully completed.

all : test all items vac: test AC voltage vdc: test DC voltage rload: test load resistance riso: test isolation resistance cap: test capacitor ren: test REN value ring: test ring voltage metering: test metering voltage Enumeration: 'riso': 5, 'all': 1, 'rload': 4, 'vac': 2, 'cap': 6, 'metering': 9, 'vdc': 3, 'ren': 7, 'ring': 8.

Force test even the port is in use. Enumeration: 'notForce': 2, 'force': 1.

Enumeration: 'yes': 1, 'no': 2.

Perform specified MLT relay function, or turn off MLT relay function in specified subscriber.

An entry of mltRelayTable.

By default, relay function is turned off. Enumeration: 'both': 3, 'out': 2, 'off': 4, 'in': 1.

Enable/disable IGMP protocol. Enumeration: 'enableProxy': 1, 'enableSnooping': 2, 'disable': 3.

Default bandwidth requirement for a multicast channel.

The maximum number of row entries that user can create in mcastBwTable.

This table defines bandwidth budget for a range of multicast IP channels.

An entry of mcastBwTable.

The index which specify the entry.

The start multicast IP of the bandwidth control range.

The end multicast IP of the bandwidth control range.

The bandwidth budget for the multicast IP channels.

The row status of the entry.

This table specify the multicast bandwidth control of the port.

An entry of mcastBwPortTable.

Enable/disable multicast bandwidth control for a port. Enumeration: 'enable': 1, 'disable': 2.

Set bandwidth threshold for a port.

This table specify the IGMP count limiting of the port.

An entry of igmpCountPortTable.

Enable/disable IGMP count limiting for a port. Enumeration: 'enable': 1, 'disable': 2.

The maximum allowed IGMP report count for a port.

The maximum number of row entries that user can create in mvlanTable.

A table containing static configuration information for each multicast VLAN configured into the device.

An entry of mvlanTable.

The VLAN-ID refering to this VLAN.

An administratively assigned string, which may be used to identify the VLAN.

The set of ports which are permanently assigned to the egress list for this multicast VLAN.

The set of ports which should transmit egress packets for this multicast VLAN as untagged.

This object indicates the status of this entry.

A table that contains multicast to VLAN translation.

An entry of mvlanTranslateTable.

The index which specif the entry.

The start IP of the multicast VLAN translation.

The end IP of the multicast VLAN translation.

The maximum number of row entries that user can create in qryVidConfTable.

This table defines statically set VLANs used for response IGMP report.

An entry in qryVidConfTable.

VLAN ID.

This object indicates the status of this entry.

This table shows statically set or dynamically learned VLANs used for response IGMP report.

An entry in qryVidStatusTable.

VLAN type. Enumeration: 'dynamic': 2, 'static': 1.

Setting IGMP version. Enumeration: 'v2': 1, 'v3': 2.

Configure IGMP leave message handling mode. Enumeration: 'lastMemberQuery': 2, 'immediateLeave': 1.

Set IGMP query interval, 10~1000 in seconds.

Set IGMP query Robustness, 1~5.

Set IGMP query response interval, 1~100 in 100 milliseconds.

Set IGMP Last Member Query interval, 1~5 in 100 milliseconds.

Set Last Member Query Robustness, 1~5.

Enable/disable IGMP audit query. Enumeration: 'enable': 1, 'disable': 2.

Set IGMP Audit Query Interval, 1~4 in 100 milliseconds.

Set IGMP Audit Query Robustness, 1~5.

The max number of IGMP profiles in the system.

A table that contains IGMP Profiles.

The entry of IGMP Profile table.

The IGMP Profile name.

Enable/disable IGMP Profile. Enumeration: 'enable': 1, 'disable': 2.

Set maximum allowed multicast group, 1~64.

The row status of the IGMP Profile entry.

A table that contains IGMP Filters.

The entry of IGMP Filter table.

The index which specifies the filter rule.

The start IP of the filter rule.

The end IP of the filter rule.

This table specifies the IGMP Profile of the port.

An entry in igmpProfilePortTable.

The IGMP Profile of the port.

This table includes subscriber attributes for the port.

An entry in subrPortTable.

Name of the subscriber.

Telephone number of the subscriber.

This table includes common attributes describing the VDSL line. This table is supported by R2.00 and later versions.

An entry in vdslLineConfTable.

Enable/disable upstream power backoff control. Enumeration: 'enable': 1, 'disable': 2.

Set VDSL profile. Enumeration: 'adsl2plus': 9, 'vdsl2gdmt': 16, 'auto': 8, 'gdmt': 11, 'vdsl2adsl2': 15, 'adsl2': 13, 't1413': 14, 'vdsl17a': 7, 'vdsl2t1413': 18, 'vdsl2': 10, 'vdsl12a': 5, 'glite': 12, 'vdsl12b': 6, 'vdsl8a': 1, 'vdsl2glite': 17, 'vdsl8c': 3, 'vdsl8b': 2, 'vdsl8d': 4.

Set VDSL customized RFI configuration. disable: not apply RFI notch to port ansi: use pre-defined ANSI RFI notch etsi: use pre-defined ETSI notch custom: user needs to define customized RFI notch band through vdslRfiCustomTable Enumeration: 'ansi': 2, 'etsi': 3, 'disable': 1, 'custom': 4.

VTUR minimum INP value

VTUC mimimum INT value

Bit1: disable Trellis coding in ADSL mode Bit2: disable Reed-Solomon coding for ADSL Bit3: disable upstream bitswaps Bit4: disable downstream bitwaps Bit5: disable upstream 1-bit constellation support Bit6: disable the transmit windowing in ADSL2+ mode Bit7: disable S=0.5 support in G.dmt Bit8: reserved Bit9: enable nitro Bit10: enable ADSL2 Annex L Bit11: enable ADSL2+ Annex M Bit12: enable US PTM optimization Bit13: enable DS PTM optimization Bit14: enable US PHYR Bit15: enable DS PHYR

-1 means max(kl0_CO,kl0_CPE). -2 means min(kl0_CO,kl0_CPE). -3 means kl0_CO. -4 means kl0_CPE. -5 means kl0_CPE + delta as calculated from.

PSD mask type Enumeration: 'vdsl2b8x16': 36, 'vdsl2aEu128': 11, 'vdsl2b8x15': 35, 'vdsl2b8x12': 32, 'vdsl2b8x13': 33, 'vdsl2b8x10': 30, 'vdsl2b8x11': 31, 'vdsl2b7x10': 46, 'vdsl2c138b': 48, 'vdsl2b8x14': 34, 'vdsl2c276co': 51, 'vdsl2b8x8': 28, 'vdsl2b8x9': 29, 'vdsl2c276b': 49, 'vdsl2b8x4': 24, 'vdsl2b8x5': 25, 'vdsl2b8x6': 26, 'vdsl2b8x7': 27, 'vdsl2aNus0': 1, 'vdsl2b8x1': 21, 'vdsl2b8x2': 22, 'vdsl2b8x3': 23, 'vdsl2aEu48': 6, 'vdsl2aEu40': 4, 'vdsl2aEu44': 5, 'vdsl1fttexAnsiM2': 13, 'vdsl2aEu64': 10, 'vdsl1fttexAnsiM2E': 17, 'vdsl1fttexAnsiM1': 12, 'vdsl2aEu60': 9, 'vdsl2c138co': 50, 'vdslFttcabAnsiM1E': 18, 'vdsl2b7x9': 45, 'vdsl2b7x8': 44, 'vdsl2btAnfp': 47, 'vdsl2b7x3': 39, 'vdsl2b7x2': 38, 'vdsl2b7x1': 37, 'vdsl2b7x7': 43, 'vdsl2b7x6': 42, 'vdsl2b7x5': 41, 'vdsl2b7x4': 40, 'vdsl2aCt': 20, 'vdsl1fttcabAnsiM2': 15, 'vdsl1fttcabAnsiM1': 14, 'vdsl2aEu56': 8, 'vdsl2aEu52': 7, 'vdsl1QAMCompatible': 53, 'vdsl2cTcmisdn': 52, 'vdslFttcabAnsiM2E': 19, 'vdsl2aEu32': 2, 'vdsl1fttexAnsiM1E': 16, 'vdsl2aEu36': 3.

Enable/Disable DPBO Enumeration: 'enable': 1, 'disable': 2.

DPBO ESEL parameter

DPBO ESCMA parameter -1~1.5 in step of 1/256.

DPBO ESCMB parameter -1~1.5 in step of 1/256.

DPBO ESCMC parameter -1~1.5 in step of 1/256.

DPBO MUS parameter.

DPBO FMIN parameter

DPBO FMAX parameter

Valid range for setting is 1~6. Enumeration: 'psdCabEtsi': 4, 'psdCo': 1, 'unknown': 0, 'psdExchEtsi': 5, 'psdExchAnsi': 6, 'psdFlat': 2, 'psdCabAnsi': 3.

This table includes common attributes describing the VDSL port. This table is supported by R2.00 and later versions.

An entry in vdslPortConfTable.

Enable/disable the transparent LAN service. Enumeration: 'enable': 1, 'disable': 2.

The transparent LAN service s-tag VID.

The transparent LAN service s-tag priority.

Enable/disable the Double Tagging service. Enumeration: 'enable': 1, 'disable': 2.

The Double Tagging service s-tag VID.

The Double Tagging service s-tag priority.

The Double Tagging service c-tag VID.

The Double Tagging service c-tag priority.

A table that contains VLAN translation.

An entry in vdslPortVlanTranslateTable.

VPI of the vtt.

VCI of the vtt.

CXVID of the vtt.

CVID of the vtt.

SVID of the vtt.

Donwstream direction only of the vtt.

This object is used to create a new row or delete an existing row in this table.

Protocol VLAN configuration table.

An entry in vdslPortPvlanTable.

0~0xffff.

This table includes VDSL customized RFI configuration. This table is supported by R2.00 and later versions.

An entry in vdslRfiCustomTable.

Index of the table.

The start value of the customized frequency range.

The end value of the customized frequency range.

Enable or disable the customized frequency range setting. Enumeration: 'enable': 1, 'disable': 2.

This table includes VDSL UPBO configuration.

An entry in vdslLineConfUpboParamTable.

Index of the table.

This table includes VDSL DPBO configuration.

An entry in vdslLineConfDpboTable.

Index of the table.

The maximum number of PVCs which could be created on a port.

This table includes PVC configuration.

An entry in pvcTable.

VPI of the pvc.

VCI of the pvc.

Default VID of the pvc.

802.1p default priority of the pvc.

The value of this object identifies the row in the ipqosProfileTable.

Encapsulation of the pvc. Enumeration: 'llc': 1, 'vc': 2.

This object is used to create a new row or delete an existing row in this table.

Access concentrator name for paepvc.

Service name for paepvc.

The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.

Enable/disable auto detection for PPPoE/PPPoA encapsulation. Enumeration: 'enable': 1, 'disable': 2.

This table show current PVC status.

An entry in pvcStateTable.

VPI of the pvc.

VCI of the pvc.

Default VID of the pvc.

802.1p default priority of the pvc.

The value of this object identifies the channel type at runtime.

The value of this object identifies the channel encapsulation at runtime.

This table includes Routed Gateway configuration.

An entry in Routed Gateway table.

IP of RPVC gateway.

Vlan id send to this RPVC gateway.

This object is used to create a new row or delete an existing row in this table.

802.1p p bit send to this RPVC gateway.

This table includes RPVC configuration.

An entry in rpvcTable.

VPI of the rpvc.

VCI of the rpvc.

Encapsulation of the rpvc. Enumeration: 'llc': 1, 'vc': 2.

The ipqos profile of the rpvc.

The IP of the rpvc.

The IP mask of the rpvc IP.

The gateway IP of rpvc.

This object is used to create a new row or delete an existing row in this table.

This table includes RPVC route domain configuration.

An entry in rpvcRouteDomainTable.

VPI of the rpvc.

VCI of the rpvc.

The route domain IP.

The IP mask of the route domain IP.

This object is used to create a new row or delete an existing row in this table.

Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg.

Flush the RPVC ARP proxy table. Enumeration: 'enable': 1.

This table includes Down Stream Bcast configuration.

An entry in Down Stream Bcast table.

downstream broadcast disabled vid.

This object is used to create a new row or delete an existing row in this table.

This table includes PPPoAoE PVC configuration.

An entry of paepvcTable.

VPI of the pvc.

VCI of the pvc.

Default VID of the pvc.

Encapsulation of the paepvc. Enumeration: 'llc': 1, 'vc': 2.

802.1p default priority of the pvc.

The value of this object identifies the row in the ipqosProfileTable.

Access concentrator name.

Service name.

The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.

This object is used to create a new row or delete an existing row in this table.

Default C-VID of the pvc.

802.1p default C-priority of the pvc.

This table includes Transparent LAN Service (TLS) PVC configuration.

An entry of tlspvcTable.

VPI of the pvc.

VCI of the pvc.

s-tag VLAN ID of the pvc.

Encapsulation of the tlspvc. Enumeration: 'llc': 1, 'vc': 2.

s-tag priority of the pvc.

The value of this object identifies the row in the ipqosProfileTable.

This object is used to create a new row or delete an existing row in this table.

This table includes Double Tagging (DT) PVC configuration.

An entry of dtpvcTable.

VPI of the pvc.

VCI of the pvc.

s-tag VLAN ID of the pvc.

s-tag priority of the pvc.

c-tag VLAN ID of the pvc.

c-tag priority of the pvc.

Encapsulation of the dtpvc. Enumeration: 'llc': 1, 'vc': 2.

The value of this object identifies the row in the ipqosProfileTable.

This object is used to create a new row or delete an existing row in this table.

Specified the configured DTPVC is a super channel. Enumeration: 'enable': 1, 'disable': 2.

Access concentrator name for paepvc.

Service name for paepvc.

The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.

Enable/disable auto detection for PPPoE/PPPoA encapsulation. Enumeration: 'enable': 1, 'disable': 2.

This table show current DTPVC status.

An entry in dtpvcStateTable.

VPI of the dtpvc.

VCI of the dtpvc.

Default S-VID of the dtpvc.

S-priority of the dtpvc.

Default C-VID of the dtpvc.

C-priority of the dtpvc.

The value of this object identifies the channel type at runtime.

The value of this object identifies the channel encapsulation at runtime.

This table includes common attributes describing the VoIP line.

An entry in voipSipLineConfTable.

SIP profile name.

SIP call service profile name.

DSP profile name.

The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, Reserved Byte 5~11:Each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.

The managed object is for VoIP configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port

This table includes VoIP tel for the port.

An entry in voipPortTelTable.

VoIP's telephone number of the specified port.

This table includes common attributes describing the VoIP line.

An entry in voipH248LineConfTable.

MG name.

DSP profile name.

DSP profile name for Voice Band Data (FAX or Modem) mode.

This table includes Termination name.

An entry in voipPortH248TerminationTable.

Termination name of MG.

This table includes Port Gain.

An entry in voipPortGainTable.

TX Gain of the port, -200~200 in unit of 0.1dB.

RX Gain of the port, -200~200 in unit of 0.1dB.

This table includes Port Seizure Mode.

An entry in voipPortSeizureModeTable.

Port Seizure Mode. Enumeration: 'groundstart': 2, 'loopstart': 1.

This table includes VoIP port SIP authentication related configuration.

An entry in voipPortSipAuthTable.

Authentication mode for VoIP port SIP registration. Enumeration: 'profile': 1, 'line': 2.

VoIP port SIP registration username.

Password is necessary or not for VoIP port SIP registration. Enumeration: 'on': 1, 'off': 2.

VoIP port SIP registration password.

This table includes VoIp port SIP call service related configuration.

An entry in voipPortSipCallsvcTable.

VoIP port SIP call service mode. Enumeration: 'profile': 1, 'line': 2.

Bit 1 callforward : call forward(Not supported) Bit 2 callhold : call hold Bit 3 callwait : call waiting Bit 4 callreturn : call return(Not supported) Bit 5 calltransfer : call transfer Bit 6 clip : caller line identification presentation (Caller ID) Bit 7 clir : caller line identification restriction Bit 8 dnd : do not disturb Bit 9 conference : native 3-way conference

Perform calling party control, or turn off. Enumeration: 'on': 1, 'off': 2.

VoIP port SIP delay hang up time of called party in seconds.

A table containing the per port SNR Margin configuration.

An entry of snrMgnTable.

Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration. Enumeration: 'profile': 0, 'line': 1.

Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.

Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.

Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.

Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.

Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.

Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.

Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.

Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.

Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.

Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.

A table containing the per port DSL Rate configuration.

An entry of dslRateTable.

Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration. Enumeration: 'profile': 0, 'line': 1.

The latency mode is fast or interleave Enumeration: 'interleave': 1, 'fast': 2.

Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.

Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.

Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps

Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency

Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.

Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps.

A table containing the G.Bond configuration information for each bonding group of the device.

An entry of gbondTable.

An administratively assigned string, which may be used to identify bonding group.

The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.

The UP stream rate.

The DOWN stream rate.

This object indicates the status of this entry.

This table includes sra shift margin related configuration.

An entry in ipqosProfileTable.

This object identifies a row in this table.

Specifies the downstream SRA Down Shift Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. in unit of 1 db.

Specifies the downstream SRA UP Shift Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. in unit of 1 db.

Specifies the downstream SRA Down Shift time in units of 1 sec , for a range of 0 to 16383 sec. in unit of 1 sec.

Specifies the downstream SRA UP Shift time in units of 1 sec , for a range of 0 to 16383 sec. in unit of 1 sec.

Specifies the upstream SRA Down Shift Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. in unit of 1 db.

Specifies the upstream SRA UP Shift Margin in units of 0.25 dB, for a range of 0 to 31.75 dB. in unit of 1 db.

Specifies the upstream SRA Down Shift time in units of 1 sec , for a range of 0 to 16383 sec. in unit of 1 sec.

Specifies the upstream SRA UP Shift time in units of 1 sec , for a range of 0 to 16383 sec. in unit of 1 sec.

This object is used to create a new row or modify or delete an existing row in this table.

The maximum number of SIP profiles supported by the system.

This table includes SIP protocol related configuration.

An entry in sipProfileTable.

This object is used by the SIP profile table in order to identify a row of this table.

IP used for SIP registration or SIP domain name.

Registration server IP or registration server domain name.

Proxy server IP or proxy server doamin name.

SIP UA port number.

Registration server port number.

Proxy server port number.

Enumeration: 'useSipUri': 1, 'useTelUri': 2.

802.1p bit for SIP and RTP packet.

DSCP for SIP and RTP packet.

Enumeration: 'on': 1, 'off': 2.

Session expiration time in seconds.

Enumeration: 'on': 1, 'off': 2.

This object is used to create a new row or delete an existing row in the table.

Registration expiration time in seconds.

The maximum number of SIP call service profiles supported by the system.

This table includes SIP call service related configuration.

An entry in sipCallSvcProfileTable.

This object is used by the SIP call service profile table in order to identify a row of this table.

Password is necessary or not for SIP registration. Enumeration: 'on': 1, 'off': 2.

SIP registration password.

Enumeration: 'on': 1, 'off': 2.

Country code, only digit 0..9 are allowed.

National destination code, only digit 0..9 are allowed.

Numbering plan table name.

Bit 1 callforward : call forward(Not supported) Bit 2 callhold : call hold Bit 3 callwait : call waiting Bit 4 callreturn : call return(Not supported) Bit 5 calltransfer : call transfer Bit 6 clip : caller line identification presentation (Caller ID) Bit 7 clir : caller line identification restriction Bit 8 dnd : do not disturb Bit 9 conference : native 3-way conference

dtmf bypass : bypass DTMF tone dtmf rfc2833 : DTMF tone relay according to RFC2833 dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload dtmf sipinfo : DTMF tone relay by SIP INFO message Enumeration: 'sipinfo': 4, 'rfc2833': 2, 'rfc2833like': 3, 'bypass': 1.

fax g711 : FAX service pass through by ITU-T G.711 fax t38 : FAX service by ITU-T T.38 Enumeration: 'g711': 1, 't38': 2.

This object is used to create a new row or delete an existing row in the table.

flash invite : will send SIP INVITE message while press flash button. flash bypass : flash event will be handled by current switch type specified in sipCallSvcProfileSwitchType. flash rfc2833 : flash event will send by RTP event (16) defined in RFC 2833. flash rfc2833like : flash event will send by SIP INFO message but RTP payload. flash sipinfo-1 : flash event will be sent by SIP INFO signal=16 message. flash sipinfo-2 : flash event will be sent by SIP INFO signal=hf message. flash sipinfo-3 : flash event will be sent by SIP INFO signal=hook-flash message. flash sipinfo-4 : flash event will be sent by SIP INFO plain text 'FLASH' message. flash sipinfo-5 : flash event will be sent by multiple SIP INFO signal messages and content of signal messages come from sipCallSvcProfileFlashInfo. flash sipinfo-6 : flash event will be sent by SIP INFO and payload is specified in sipCallSvcProfileFlashInfo. Enumeration: 'invite': 1, 'bypass': 10, 'sipinfo4': 7, 'sipinfo5': 8, 'sipinfo6': 9, 'sipinfo1': 4, 'sipinfo2': 5, 'sipinfo3': 6, 'rfc2833': 2, 'rfc2833like': 3.

Strings carried in SIP INFO when specified in sipCallSvcProfileFlashType is sipinfo-5 and sipinfo-6.

Softswitch type is configured to specify softswitch-dependent behavior, currently only flash event is softswitch-dependent and should follow the softswitch type setting. When configured the flash event to 'bypass', E5 will follow the softswitch type setting to report hook flash event. Enumeration: 'metaswitch': 1, 'nortel': 2.

Perform calling party control, or turn off. Enumeration: 'on': 1, 'off': 2.

Delay hang up time of called party in seconds.

The maximum number of DSP profiles supported by the system.

This table includes DSP related configuration.

An entry in dspProfileTable.

This object is used by the DSP profile table in order to identify a row of this table.

0x01: g711a 0x02: g711mu 0x03: g723 0x04: g726-16 0x05: g726-24 0x06: g726-32 0x07: g726-40 0x08: g729ab the value of dspProfileCodec is OCTET STRING, there are 8 Octets, each octect is specified as 0x01, 0x03, 0x02, 0x07,0x00, 0x00, 0x00, 0x00 (to specify different CODE in priority) specify as: g711a, g723, g711mu, g726-40

Play buffer minimum delay in milliseconds. It should be less than or equal to dspProfilePlayBufferMaxDelay.

Play buffer maximum delay in milliseconds. It should be greater than or equal to dspProfilePlayBufferMinDelay.

Echo cancellation echo tail period in milliseconds. Enumeration: 'echotail128': 4, 'echotail32': 3, 'echotail16': 2, 'echotail8': 1.

This object is used to create a new row or delete an existing row in the table.

Voice Packetization Interval(VPI) of codec G.711 in milliseconds. The values are 10, 20, 30, 40 Enumeration: 'g711x10ms': 1, 'g711x20ms': 2, 'g711x30ms': 3, 'g711x40ms': 4.

Voice Packetization Interval(VPI) of G.723 codec in milliseconds. The values are 30,60 Enumeration: 'g723x30ms': 1, 'g723x60ms': 2.

Voice Packetization Interval(VPI) of G.726 codec in milliseconds. The values are 10, 20, 30, 40 Enumeration: 'g726x10ms': 1, 'g726x40ms': 4, 'g726x20ms': 2, 'g726x30ms': 3.

Voice Packetization Interval(VPI) of G.729 codec in milliseconds. The values are 10, 20, 30, 40, 50, 60 Enumeration: 'g729x10ms': 1, 'g729x30ms': 3, 'g729x20ms': 2, 'g729x40ms': 4, 'g729x60ms': 6, 'g729x50ms': 5.

The maximum number of H248 profiles supported by the system.

This table includes H248 profile related configuration.

An entry in h248ProfileTable.

This object is used by the H248 profile table in order to identify a row of this table.

MGC IP or MGC doamin name.

MGC port number.

Secondary MGC on/off. Enumeration: 'on': 1, 'off': 2.

Secondary MGC IP or MGC doamin name. h248ProfileMgc2On needs to turn on if user want to set Secondary MGC IP or domain name.

Secondary MGC port number. h248ProfileMgc2On needs to turn on if user want to set Secondary MGC port number.

Transport procotol used by the H.248 protocol stack. Enumeration: 'udp': 1, 'tcp': 2.

Encoding type used by the H.248 protocol stack Enumeration: 'shorttext': 2, 'longtext': 1.

802.1p bit for H.248 packet.

DSCP for H.248 packet.

This object is used to create a new row or delete an existing row in the table.

VBD mode support on/off Enumeration: 'on': 1, 'off': 2.

Ephemeral Termination Prefix

Softswitch type Enumeration: 'nortelCs2000': 3, 'metaswitch': 1, 'nortelCs1500': 2.

Force using H.248 version 1 Enumeration: 'on': 1, 'off': 2.

Start of RTP port number.

End of RTP port number.

Ephemeral termination suffix start number, up to 15 digits.

Ephemeral termination suffix number length , padding zero at the front if not long enough.

Physical Termination Prefix.

Physical termination suffix start number, up to 15 digits.

Physical termination suffix number length , padding zero at the front if not long enough.

RFC2833 mode support. Enumeration: 'on': 1, 'off': 2.

Payload type of RFC2833 mode.

The maximum number of IPQOS profiles supported by the system.

This table includes IPQOS related configuration.

An entry in ipqosProfileTable.

This object is used by the IPQOS profile table in order to identify a row of this table.

The number of IPQOS queues.

This object is used to create a new row or delete an existing row in the table.

This table includes IPQOS queue related configuration.

An entry in ipqosProfileQueueTable.

IPQOS queue index.

Peak rate.(multiple of 256)

Commited rate.(multiple of 256)

Peak burst size.(mutiple of 256)

Commited burst size.(mutiple of 256)

Queue level.

Queue weight.

The table contains 802.3ad configuration.

Group ID 1 for the subtending group and 2 for the uplink group.

Enable/disable 802.3ad function. Enumeration: 'enable': 1, 'disable': 3, 'enableWithLacp': 2.

LACP system priority.

The time interval to exchange LACP packets in order to check that the peer port in the trunk group is still up. Enumeration: 'longtimeout': 2, 'shorttimeout': 1.

The table contains current status of port trunking.

Group ID 1 for the subtending group and 2 for the uplink group.

Port trunking status. Enumeration: 'down': 2, 'up': 1.

The port list which actually joins the trunking group.

The table contains DSCP mapping configuration for the adsl ports.

An entry of dscpMappingTable.

The DSCP source code point used for mapping.

The mapping p bits that will replace the source p bits in the incoming packet.

The table contains DSCP mapping configuration for the adsl ports.

An entry of dscpPortTable.

The DSCP port status. Enumeration: 'enable': 1, 'disable': 2.

A table contains configuration of isolated VLAN.

An entry of vlanIsolationTable.

Row status of the table used to create/delete an entry.

Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.

Sets TPID(Tag Protocol Identifier) of tagged frame, 0~FFFF.

A table that contains CFM information.

An entry in cfmLoopbackPortTable.

CFM loopback enable/disable on the port. Enumeration: 'enable': 1, 'disable': 2.

An entry in cfmMIPTable.

CFM MIP mac address

CFM Action enable status for the CO device Enumeration: 'enable': 1, 'disable': 2.

CFM follow standard mode Enumeration: 'modeYDot1731': 2, 'mode802Dot1Ag': 1.

CFM LBM timeout, 100-86400 ms

CFM LBM data tlv length, 0-1400 bytes

A table that contains CFM LBR results.

An entry in cfmLbrTable.

CFM lbm index.

CFM lbr index.

CFM lbr source address.

CFM lbr status. Enumeration: 'ready': 1, 'notready': 2, 'xmit': 3, 'timeout': 5, 'success': 4.

CFM lbr rtt in ms.

A table that contains DHCP Relay configuration.

The entry of DHCP Relay table.

The IP address of the DHCP Relay primary server.

The IP address of the DHCP Relay secondary server.

The current active DHCP Relay server. Enumeration: 'fourth': 4, 'fifth': 5, 'primary': 1, 'third': 3, 'secondary': 2.

Enable/disable DHCP relay and Option82 function. Enumeration: 'enable': 1, 'disable': 2.

User specific Option82 information.

DHCP relay mode. Enumeration: 'auto': 1, 'all': 2.

Enable/disable Option 82 sub-option 2. Enumeration: 'enable': 1, 'disable': 2.

User specified information for Option 82 sub-option 2.

Enable/disable DHCP Relay Enumeration: 'auto': 1, 'all': 2, 'disable': 3.

Option82 format. Enumeration: 'customer-remote-id': 3, 'private': 1, 'tr101': 2.

The IP address of the DHCP Relay interface for this VLAN.

The network mask of the DHCP Relay interface for this VLAN.

The gateway of the DHCP Relay interface for this VLAN.

The IP address of the DHCP Relay third server.

The IP address of the DHCP Relay fourth server.

The IP address of the DHCP Relay fifth server.

The VID of the DHCP Relay server for this VLAN.

Setting the VID of the test server.

Setting the IP of the test server.

Set the object to 1 to test DHCP server.

Display testing server status.

The table displays DHCP ARP.

An entry of dhcpRelayArpShowTable.

Display the VID of the DHCP ARP entry.

Display the IP of the DHCP ARP entry.

Display the MAC of the DHCP ARP entry.

Set the object to 1 to start flushing.

This table includes the status of mac filtering for each port.

An entry in macFilterPortTable.

Enable/disable MAC filtering for the port. Enumeration: 'enableMacFilter': 1, 'enableMacCount': 2, 'disable': 4, 'enableMacFilterAndMacCount': 5.

The total number of MAC addresses allowed for the port.

The mac filter mode (accept or deny) for the port. Enumeration: 'deny': 2, 'accept': 1.

The max number of mac filters supported in the system.

The max number of mac filters supported per port.

The current number of mac filters in the system.

A table that contains the mac filter addresses.

The entry of macFilterTable.

The mac address which can pass through or be rejected from the port.

The row status of the entry.

This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.

The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter.

The total number of MAC addresses allowed for a port.

A table that contains the OUI filter addresses.

The entry of ouiFilterTable.

The first three bytes of the mac address which can pass through or be rejected from the port.

The row status of the entry.

The max number of OUI filters supported per port.

This table includes the status of oui filtering for each port.

An entry in macFilterPortTable.

Enable/disable oui filtering for the port. Enumeration: 'enableOuiFilter': 1, 'disable': 2.

The oui filter mode (accept or deny) for the port. Enumeration: 'deny': 2, 'accept': 1.

This table includes DHCP snooping enable/disable for each port.

An entry of dhcpSnoopPortTable.

Enable/disable DHCP snooping for a port. Enumeration: 'enable': 1, 'disable': 2.

Set the max entries of the DHCP ARP table.

Enable/disable DHCP source MAC verify for a port. Enumeration: 'enable': 1, 'disable': 2.

This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.

The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.

This table defines DHCP static IP addresses.

An entry of dhcpStaticTable.

The IP address which can pass through the port.

Row status of the table entry.

The maximum number of DHCP static IP addresses which can be created for a port.

When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1. Enumeration: 'drop': 2, 'replace': 1.

aclsetTable.

An entry of aclSetTable.

VPI value

VCI value

ACL Profile name

RowStatus of aclSetEntry

aclProfileTable.

An entry of aclProfileTable.

Profile rule name

The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), vlan sip (14), vlan dip (15), vlan sport tcp|udp (16), vlan dport tcp|udp (17)

Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.

Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport

Profile rule etype

Profile rule vid

Profile rule source MAC

Profile rule destination MAC

Profile rule priority

Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype

Profile action to replace to this rate

Profile action to replace to this vlan

Profile action to replace to this priority

The row status of the entry.

Source IP.

Destination IP.

Source port.

Destination port.

A table that contains PPPoE intermediate agent configuration.

An entry of pppoeAgentTable.

Enable/disable PppoE intermediate agent function. Enumeration: 'enable': 1, 'disable': 2.

User specific Option82 information.

Row status of the table entry.

Option82 format. Enumeration: 'private': 1, 'tr101': 2.

The maximum number of rows that can be created in pppoeAgentTable.

This MAC address will be used to replace client's MAC address.

The table contains N to 1 MAC configuration for DSL ports.

An entry of n1macPortTable.

The port status of n1mac function. Enumeration: 'enable': 1, 'disable': 2.

A table that contains MAC Force Forwarding configuration.

An entry of macFfTable.

Index of the MACFF.

The VLAN-ID refering to this AR/AS.

IP of this AR/AS

The source IP address of the MACFF.

The subnet mask of source IP mask.

The row status of the MacFfEntry entry.

Set the object to 1 to flush mac table.

The max number of macff Vlans supported in the system.

A table that contains MAC Force Forwarding Vlan configuration.

An entry of macFfVlanTable.

Row status of the table used to create/delete an entry.

An entry of macFfTable.

The port number, 1 ~ 48.

VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.

The specified IP range.

Mask_bits is 24 .. 32.

The row status used to configure the table entry.

An entry of macFfTable.

VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.

The mac address.

The row status used to configure the table entry.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'mar': 3, 'feb': 2, 'aug': 8, 'sep': 9, 'apr': 4, 'jun': 6, 'jul': 7, 'jan': 1, 'may': 5, 'nov': 11, 'dec': 12, 'oct': 10.

Enumeration: 'second': 2, 'last': 5, 'fourth': 4, 'third': 3, 'first': 1.

Enumeration: 'wed': 4, 'sun': 1, 'th': 5, 'tus': 3, 'mon': 2, 'fri': 6, 'sat': 7.

1h 01h00, 2h 02h00 3h 03h00 4h 04h00 5h 05h00 6h 06h00 7h 07h00 8h 08h00 9h 09h00 10h 10h00 11h 11h00 12h 12h00 13h 13h00 14h 14h00 15h 15h00 16h 16h00 17h 17h00 18h 18h00 19h 19h00 20h 20h00 21h 21h00 22h 22h00 23h 23h00 Enumeration: 'h23h00': 23, 'h7h00': 7, 'h12h00': 12, 'h0h00': 0, 'h10h00': 10, 'h11h00': 11, 'h9h00': 9, 'h17h00': 17, 'h21h00': 21, 'h8h00': 8, 'h18h00': 18, 'h3h00': 3, 'h19h00': 19, 'h15h00': 15, 'h16h00': 16, 'h2h00': 2, 'h4h00': 4, 'h1h00': 1, 'h6h00': 6, 'h5h00': 5, 'h22h00': 22, 'h14h00': 14, 'h20h00': 20, 'h13h00': 13.

Enumeration: 'mar': 3, 'feb': 2, 'aug': 8, 'sep': 9, 'apr': 4, 'jun': 6, 'jul': 7, 'jan': 1, 'may': 5, 'nov': 11, 'dec': 12, 'oct': 10.

Enumeration: 'second': 2, 'last': 5, 'fourth': 4, 'third': 3, 'first': 1.

Enumeration: 'wed': 4, 'sun': 1, 'th': 5, 'tus': 3, 'mon': 2, 'fri': 6, 'sat': 7.

1h 01h00, 2h 02h00 3h 03h00 4h 04h00 5h 05h00 6h 06h00 7h 07h00 8h 08h00 9h 09h00 10h 10h00 11h 11h00 12h 12h00 13h 13h00 14h 14h00 15h 15h00 16h 16h00 17h 17h00 18h 18h00 19h 19h00 20h 20h00 21h 21h00 22h 22h00 23h 23h00 Enumeration: 'h23h00': 23, 'h7h00': 7, 'h12h00': 12, 'h0h00': 0, 'h10h00': 10, 'h11h00': 11, 'h9h00': 9, 'h17h00': 17, 'h21h00': 21, 'h8h00': 8, 'h18h00': 18, 'h3h00': 3, 'h19h00': 19, 'h15h00': 15, 'h16h00': 16, 'h2h00': 2, 'h4h00': 4, 'h1h00': 1, 'h6h00': 6, 'h5h00': 5, 'h22h00': 22, 'h14h00': 14, 'h20h00': 20, 'h13h00': 13.

A table that contains information about secured clients.

A list of secured client entry.

The index of the entry.

The starting IP address of the secured client set.

The ending IP address of the secured client set.

Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions areh BIT 1h telnet BIT 2h ftp BIT 3h web BIT 4h icmp BIT 5h not support BIT 6h snmp.

Enable/disable the entry. Enumeration: 'enable': 1, 'disable': 2.

A table that contains external alarm information.

The entry of external alarm table.

The index of the entry.

The external alarm name.

Dispaly 'Normal' or 'Alarm' string

The external alarm triggered mode. Enumeration: 'closeAlarm': 1, 'openAlarm': 2.

User authentication procsssing mode. Enumeration: 'radius': 2, 'local': 1, 'localThenRadius': 3.

The IP address of the authentication server.

The port of the authentication server.

The secret between the authentication server and the NE for authentication process.

A table that contains user information.

An entry of userTable.

The user name.

The user password.

The user priviledge to decide what operation the user can and cannot do. Enumeration: 'high': 1, 'middle': 2, 'low': 3.

The row status used to create or delete a user.

The user default priviledge to be assigned when radius authentication succeeds but no user priviledge information(radius service-type) is provided. Enumeration: 'high': 1, 'middle': 2, 'deny': 4, 'low': 3.

Enable/disable upstream broadcast control. Enumeration: 'enable': 1, 'disable': 2.

Enable internal overriding mode to VLAN, DSCP or IP Precedence, or disable the overriding mode. Enumeration: 'ippre': 4, 'disable': 1, 'dscp': 3, 'vlan': 2.

Set the internal default p.bit after overiding. All values not configured in the overriding table are assigned to the default p.bit

This table includes downstream QoS overriding information.

An entry in dsQoSOverridingTable.

Internal P.bit after overriding.

VLAN ID, DSCP, or IP Precedence based on the internal overriding mode configured. VLAN ID 1 ~ 4094, DSCP 0 ~ 63, IP Precedence 0 ~ 7. value_list exampleh <1>, <1,3>, <1,5,6~10>.

Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.

If system configuration has been changed. Enumeration: 'yes': 1, 'no': 2.

Configure the target firmware version that will be upgraded.

Enable/disable firmware upgrade version checking feature. Enumeration: 'enable': 1, 'disable': 2.

Display current firmware upgrade status.

5~1800 secs, 0h reboot immediately.

Display the remaining time of scheduled reboot.

cancel the scheduled reboot. Enumeration: 'cancel': 1.

The total number of IGMP query messages received.

The total number of IGMP report messages received.

The total number of IGMP leave messages received.

The total number of IGMP learned groups.

This table includes igmp group information.

An entry in igmpGroupTable.

igmp group IP

vlan id

number Of Members

Group Member Ports

This table includes igmp Group port information.

An entry in igmpGroupPortTable.

Igmp Group IP

Igmp Group vid

A table that displays IGMP learned group member information.

An entry of igmpGroupV2Table.

The IGMP group VLAN ID.

The multicast IP address.

The number of member ports in the group.

The member port list of the group.

A table that displays IGMP joined groups in this port.

An entry of igmpGroupPortV2Table.

The IGMP group VLAN ID.

The multicast IP address.

The source IP address that joins the IGMP group.

A table that displays IGMP related counter values in this port.

An entry of igmpPortCtrlPduTable.

The total number of IGMP query messages received in this port.

The total number of IGMP report messages received in this port.

The total number of IGMP leave messages received in this port.

The total number of active IGMP groups in this port.

The total number of groups left by audit query.

This table shows the IP addresses and netmasks offered by the DHCP server.