ATT-NETGATE-MIB: View SNMP OID List / Download MIB

VENDOR: ATT (AMERICAN TELEPHONE AND TELEGRAPH)


 Home MIB: ATT-NETGATE-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, INET-ADDRESS-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 att_2 1.3.6.1.4.1.74
       att_products 1.3.6.1.4.1.74.1
           attNetGate 1.3.6.1.4.1.74.1.30
                 ngHardwareInfo 1.3.6.1.4.1.74.1.30.1
                     nghwHardwareVersion 1.3.6.1.4.1.74.1.30.1.1 displaystring read-only
Hardware Version.
                     nghwCodeVersion 1.3.6.1.4.1.74.1.30.1.2 displaystring read-only
Software code version.
                     nghwAccount 1.3.6.1.4.1.74.1.30.1.3 displaystring read-only
The account in Service Manager this device is registered under.
                     nghwUtcOffset 1.3.6.1.4.1.74.1.30.1.4 integer32 read-only
Indicates how many minutes away from UTC time the device is located. Values must be in 30 minute increments. Valid range is -840 to 840.
                     nghwDstAllowed 1.3.6.1.4.1.74.1.30.1.5 integer read-only
Indicates if the device is located in an area that observes daylight savings time. Enumeration: 'dstNotAllowed': 0, 'dstAllowed': 1.
                     nghwDstActive 1.3.6.1.4.1.74.1.30.1.6 integer read-only
Indicates if daylight savings time is current active at this date and time. Enumeration: 'dstActive': 1, 'dstNotActive': 0.
                     nghwWanConnectionMethod 1.3.6.1.4.1.74.1.30.1.7 integer read-only
The current primary IPv4 WAN connection setting. This is configured via the web interface and is not read from Service Manager. Enumeration: 'wanConfigISDNPri': 5, 'wanConfigDialPri': 4, 'wanConfigDHCP': 2, 'wanConfigPPPoA': 6, 'wanConfigPPPoE': 3, 'wanConfigCellularPer': 7, 'wanConfigCellularPri': 8, 'wanConfigStatic': 1, 'wanConfigUnknown': 0.
                     nghwHostname 1.3.6.1.4.1.74.1.30.1.8 displaystring read-only
The name of the current host.
                     nghwDnsServers 1.3.6.1.4.1.74.1.30.1.9
                         ngDnsTable 1.3.6.1.4.1.74.1.30.1.9.1 no-access
The (conceptual) table of DNS on the device. An entry shall be placed in the storage table for each DNS.
                             ngDnsEntry 1.3.6.1.4.1.74.1.30.1.9.1.1 no-access
A (conceptual) entry for one logical DNS area on the host.
                                 ngdnIndex 1.3.6.1.4.1.74.1.30.1.9.1.1.1 integer32 no-access
A unique value for each logical DNS contained on the device.
                                 ngdnServer 1.3.6.1.4.1.74.1.30.1.9.1.1.2 ipaddress read-only
The IP address of an indivdual name server in use.
                         ngDnsIPv6Table 1.3.6.1.4.1.74.1.30.1.9.2 no-access
The (conceptual) table of IPv6 DNS on the device. An entry shall be placed in the storage table for each DNS.
                             ngDnsIPv6Entry 1.3.6.1.4.1.74.1.30.1.9.2.1 no-access
A (conceptual) entry for one logical IPv6 DNS area on the host.
                                 ngdnIPv6Index 1.3.6.1.4.1.74.1.30.1.9.2.1.1 integer32 no-access
A unique value for each logical IPv6 DNS contained on the device.
                                 ngdnIPv6Server 1.3.6.1.4.1.74.1.30.1.9.2.1.2 inetaddressipv6 read-only
The IPv6 IP address of an indivdual name server in use.
                     nghwDeviceStatus 1.3.6.1.4.1.74.1.30.1.10 integer read-only
The current device status. Enumeration: 'deviceActive': 0, 'deviceDiscontinued': 2, 'deviceInActive': 1, 'deviceBadVlanSwitch': 4, 'deviceNotConfigured': 3.
                     nghwLanguage 1.3.6.1.4.1.74.1.30.1.11 displaystring read-only
The language that will be displayed on the CGI web interface. The valid values are: EN = English JA = Japanese ES = Spanish BP = Brazil Portuguese FC = French Canadian TC = Traditional Chinese SC = Simplified Chinese
                     nghwCustComm 1.3.6.1.4.1.74.1.30.1.12
                           ngCustCommTable 1.3.6.1.4.1.74.1.30.1.12.1 no-access
The (conceptual) table of customer info (such as comments) on the device. An entry shall be placed in the storage table for each one.
                               ngCustCommEntry 1.3.6.1.4.1.74.1.30.1.12.1.1 no-access
A (conceptual) entry for one logical customer comment area on the host.
                                   ngcuIndex 1.3.6.1.4.1.74.1.30.1.12.1.1.1 integer32 no-access
A unique value for each logical customer info.
                                   ngcuCustComment 1.3.6.1.4.1.74.1.30.1.12.1.1.2 displaystring read-only
A free-format field that can be added to the AT&T NetGate's profile at a customer's request. Currently only one comment field can be specified.
                     nghwPorts 1.3.6.1.4.1.74.1.30.1.13
                           ngPortTable 1.3.6.1.4.1.74.1.30.1.13.1 no-access
The (conceptual) table of ports on the device. An entry shall be placed in the storage table for each port.
                               ngPortEntry 1.3.6.1.4.1.74.1.30.1.13.1.1 no-access
A (conceptual) entry for one logical port area on the host.
                                   ngpoIndex 1.3.6.1.4.1.74.1.30.1.13.1.1.1 integer32 no-access
A unique value for each logical port contained on the device.
                                   ngpoStatus 1.3.6.1.4.1.74.1.30.1.13.1.1.2 integer read-only
The link status of an individual hardware port. Enumeration: 'active': 1, 'unknown': 2, 'inactive': 0.
                     nghwCurrentWanConnectionMethod 1.3.6.1.4.1.74.1.30.1.14 integer read-only
The currently active IPv4 WAN connection, which may differ from the configured primary IPv4 WAN connection setting. For example, the primary IPv4 WAN is configured for DHCP (wanConfigDHCP), but because of a network outage the PPPoE secondary WAN connection (wanConfigPPPoE2) is currently providing connectivity. Enumeration: 'wanConfigISDNPri': 5, 'wanConfigDialPri': 4, 'wanConfigDHCP2': 10, 'wanConfigDHCP': 2, 'wanConfigPPPoA': 6, 'wanConfigStatic2': 9, 'wanConfigPPPoE2': 11, 'wanConfigPPPoE': 3, 'wanConfigCellularPer': 7, 'wanConfigCellularPri': 8, 'wanConfigStatic': 1, 'wanConfigUnknown': 0.
                     nghwIPv6WanConnectionMethod 1.3.6.1.4.1.74.1.30.1.15 integer read-only
The current primary IPv6 WAN connection setting. This is configured via the web interface and is not read from Service Manager. Enumeration: 'wanConfigOff': 15, 'wanConfigIPv6DHCP': 13, 'wanConfigIPv6Static': 12, 'wanConfigUnknown': 0, 'wanConfigIPv6Stateless': 14.
                     nghwIPv6CurrentWanConnectionMethod 1.3.6.1.4.1.74.1.30.1.16 integer read-only
The currently active IPv6 WAN connection, which may differ from the configured primary IPv6 WAN connection setting. For example, the primary IPv4 WAN is configured for DHCP (wanConfigIPv6DHCP), but because of a network outage the static IP secondary WAN connection (wanConfigIPv6Static2) is currently providing connectivity. Enumeration: 'wanConfigIPv6Stateless2': 18, 'wanConfigIPv6Static': 12, 'wanConfigOff': 15, 'wanConfigIPv6DHCP2': 17, 'wanConfigIPv6Stateless': 14, 'wanConfigIPv6Static2': 16, 'wanConfigIPv6DHCP': 13, 'wanConfigUnknown': 0.
                     nghwLastFullQueryTimeDAT 1.3.6.1.4.1.74.1.30.1.17 dateandtime read-only
The last time when the AT&T NetGate was successfully able to retrieve its full profile from an AT&T Administration Server.
                     nghwLastAnyQueryTimeDAT 1.3.6.1.4.1.74.1.30.1.18 dateandtime read-only
The last time when the AT&T NetGate was successfully able to retrieve its profile from an AT&T Administration Server. If this time does not match nghwLastFullQueryTimeDAT then that means only part of the profile was retrieved. This is to prevent any possible reboots if critical portions of the profile were to change.
                 ngInterfaceInfo 1.3.6.1.4.1.74.1.30.2
                     ngifActiveWanIface 1.3.6.1.4.1.74.1.30.2.1 displaystring read-only
The interface that is currently in use for the primary connection.
                     ngifTotalBytesIn 1.3.6.1.4.1.74.1.30.2.2 unsigned32 read-only
Total bytes in on the active WAN interface.
                     ngifTotalBytesOut 1.3.6.1.4.1.74.1.30.2.3 unsigned32 read-only
Total bytes out on the active WAN interface.
                     ngifTimeInDial 1.3.6.1.4.1.74.1.30.2.4 timeticks read-only
How long the current dial connection has been up.
                 ngVlanInfo 1.3.6.1.4.1.74.1.30.3
                     ngVlanTable 1.3.6.1.4.1.74.1.30.3.1 no-access
The (conceptual) table of VLANs on the device. An entry shall be placed in the storage table for each VLAN.
                         ngVlanEntry 1.3.6.1.4.1.74.1.30.3.1.1 no-access
A (conceptual) entry for one logical VLAN area on the host.
                             ngvlIndex 1.3.6.1.4.1.74.1.30.3.1.1.1 integer32 no-access
A unique value for each logical VLAN contained by the device.
                             ngvlId 1.3.6.1.4.1.74.1.30.3.1.1.2 integer32 read-only
This is the number assigned to the VLAN. Please note: A VLAN with an ID of 4070 is a special VLAN used to hold ports that are disabled.
                             ngvlPorts 1.3.6.1.4.1.74.1.30.3.1.1.3 displaystring read-only
The ports assigned to the VLAN.
                             ngvlSpeed 1.3.6.1.4.1.74.1.30.3.1.1.4 integer read-only
This is the speed supported on the Ethernet interfaces. Enumeration: 'speed10MbitHalfDuplex': 2, 'speed100MbitFullDuplex': 5, 'autoNegot': 1, 'speed100MbitHalfDuplex': 4, 'notActive': 0, 'speed10MbitFullDuplex': 3.
                             ngvlIpRange 1.3.6.1.4.1.74.1.30.3.1.1.5 displaystring read-only
The range of IP addresses handed out via DHCP on this VLAN. Values will be 0.0.0.0 0.0.0.0 if DHCP is not enabled on this VLAN. Followed by number of addresses assigned and number of total addresses. NOTE: As of AT&T NetGate version 5.3 the number of addresses assigned will no longer be returned. A zero will be returned for that field.
                             ngvlDhcpRelayAddr 1.3.6.1.4.1.74.1.30.3.1.1.6 displaystring read-only
When the DHCP Type is 'R', this is the address the AT&T NetGate devices uses to relay DHCP requests. This field is required when the DHCP Type is 'R'. A second address can be specified.
                             ngvlDhcpDefRoute 1.3.6.1.4.1.74.1.30.3.1.1.7 ipaddress read-only
This field is required when VRRP Active Indicator is 'Y' and is optional otherwise. If specified, it must be within the local LAN subnet of the AT&T NetGate but cannot fall within the DHCP pool start and end addresses. For the DHCP Default Route on the AT&T NetGate device profile, if entered, the address must be within the network specified by the LAN Address and LAN Subnet, but not within the address range specified by the DHCP Start Address and DHCP End Address.
                             ngvlLanAddr 1.3.6.1.4.1.74.1.30.3.1.1.8 ipaddress read-only
This is the LAN address for the device on the VLAN.
                             ngvlLanSubAddr 1.3.6.1.4.1.74.1.30.3.1.1.9 ipaddress read-only
This is the LAN subnet address for the device on the VLAN.
                             ngvlIPv6IpRangeStart 1.3.6.1.4.1.74.1.30.3.1.1.10 inetaddressipv6 read-only
The start of the range of IPv6 IP addresses handed out via DHCP on this VLAN. Value will be all zeroes if DHCP is not enabled on this VLAN.
                             ngvlIPv6IpRangeEnd 1.3.6.1.4.1.74.1.30.3.1.1.11 inetaddressipv6 read-only
The end of the range of IPv6 IP addresses handed out via DHCP on this VLAN. Value will be all zeroes if DHCP is not enabled on this VLAN.
                             ngvlIPv6DhcpRelayAddrPri 1.3.6.1.4.1.74.1.30.3.1.1.12 inetaddressipv6 read-only
When the DHCP Type is 'R', this is the primary address the AT&T NetGate devices uses to relay DHCP requests. This field is required when the DHCP Type is 'R' and IPv6 is in use.
                             ngvlIPv6DhcpRelayAddrBak 1.3.6.1.4.1.74.1.30.3.1.1.13 inetaddressipv6 read-only
When the DHCP Type is 'R', this is the primary address the AT&T NetGate devices uses to relay DHCP requests.
                             ngvlIPv6LanAddr 1.3.6.1.4.1.74.1.30.3.1.1.14 inetaddressipv6 read-only
This is the IPv6 LAN address for the device on the VLAN.
                             ngvlIPv6LanPrefix 1.3.6.1.4.1.74.1.30.3.1.1.15 integer32 read-only
This is the IPv6 LAN prefix for the device on the VLAN.
                 ngVrrpInfo 1.3.6.1.4.1.74.1.30.4
                     ngVrrpTable 1.3.6.1.4.1.74.1.30.4.1 no-access
The (conceptual) table of VRRPs on the device. An entry shall be placed in the storage table for each VRRP.
                         ngVrrpEntry 1.3.6.1.4.1.74.1.30.4.1.1 no-access
A (conceptual) entry for one logical VRRP area on the host.
                             ngvrIndex 1.3.6.1.4.1.74.1.30.4.1.1.1 integer32 no-access
A unique value for each logical VRRP contained by the device.
                             ngvrIface 1.3.6.1.4.1.74.1.30.4.1.1.2 displaystring read-only
The interface associated with this VRRP.
                             ngvrId 1.3.6.1.4.1.74.1.30.4.1.1.3 integer32 read-only
Virtual router ID.
                             ngvrMasterStatus 1.3.6.1.4.1.74.1.30.4.1.1.4 integer read-only
Shows what the status is (master, backup, not active). Enumeration: 'vrrpMasterState': 1, 'vrrpBackupState': 2, 'vrrpNotRunning': 0, 'vrrpFaultState': 3.
                             ngvrPriority 1.3.6.1.4.1.74.1.30.4.1.1.5 integer read-only
VRRP_PRIO_OWNER 255 /* priority of the ip owner -- rfc2338.5.3.4 */ VRRP_PRIO_DFL 100 /* default priority -- rfc2338.5.3.4 */ VRRP_PRIO_STOP 0 /* priority to stop -- rfc2338.5.3.4 */ Enumeration: 'default': 100, 'owner': 255, 'stop': 0.
                 ng3GInfo 1.3.6.1.4.1.74.1.30.5
                     ng3GTable 1.3.6.1.4.1.74.1.30.5.1 no-access
The (conceptual) table of 3G cards on the device. An entry shall be placed in the storage table for each 3G card.
                         ng3GEntry 1.3.6.1.4.1.74.1.30.5.1.1 no-access
A (conceptual) entry for one logical 3G card area on the host.
                             ng3gIndex 1.3.6.1.4.1.74.1.30.5.1.1.1 integer32 no-access
A unique value for each logical 3G card contained by the device.
                             ng3gSlotNum 1.3.6.1.4.1.74.1.30.5.1.1.2 integer32 read-only
The slot the card is plugged into. Returns -1 if no card is found.
                             ng3gModemType 1.3.6.1.4.1.74.1.30.5.1.1.3 displaystring read-only
The modem type.
                             ng3gManufacturer 1.3.6.1.4.1.74.1.30.5.1.1.4 displaystring read-only
The 3G card manufacturer.
                             ng3gModel 1.3.6.1.4.1.74.1.30.5.1.1.5 displaystring read-only
The 3G card model.
                             ng3gRevision 1.3.6.1.4.1.74.1.30.5.1.1.6 displaystring read-only
The 3G card revision.
                             ng3gID 1.3.6.1.4.1.74.1.30.5.1.1.7 displaystring read-only
Either the IMEI or ESN depending on the card.
                             ng3gSignalStrength 1.3.6.1.4.1.74.1.30.5.1.1.8 integer32 read-only
Signal Strength at the connect.
                             ng3gCarrier 1.3.6.1.4.1.74.1.30.5.1.1.9 displaystring read-only
Information about the carrier.
                             ng3gImsiStatus 1.3.6.1.4.1.74.1.30.5.1.1.10 displaystring read-only
The IMSI attach status.
                             ng3gCellConnNetwork 1.3.6.1.4.1.74.1.30.5.1.1.11 displaystring read-only
The connected network.
                             ng3gPhoneNum 1.3.6.1.4.1.74.1.30.5.1.1.12 displaystring read-only
The cell phone number.
                             ng3gApn 1.3.6.1.4.1.74.1.30.5.1.1.13 displaystring read-only
The access point name.
                             ng3gApnUser 1.3.6.1.4.1.74.1.30.5.1.1.14 displaystring read-only
The APN userid. Only populated when the access point name exists.
                             ng3gApnPassword 1.3.6.1.4.1.74.1.30.5.1.1.15 displaystring read-only
The APN password. Only populated when the access point name exists.
                             ng3gCellModemPresent 1.3.6.1.4.1.74.1.30.5.1.1.16 integer read-only
If the cellular modem is a supported unit that allows the AT&T NetGate to query its current status then this value will indicate whether or not the unit is physically present. Unsupported units will always have a value of 'unknown'. Enumeration: 'unknown': 0, 'present': 1, 'missing': 2.
                             ng3gSIMCardNumber 1.3.6.1.4.1.74.1.30.5.1.1.17 displaystring read-only
The SIM number of the card.
                             ng3gDeviceType 1.3.6.1.4.1.74.1.30.5.1.1.18 integer read-only
The type of hardware of the cellular modem. Enumeration: 'unknown': 0, 'pcmcia': 1, 'usb': 2.
                 ngTunnelInfo 1.3.6.1.4.1.74.1.30.6
                     ngTunnelTable 1.3.6.1.4.1.74.1.30.6.1 no-access
The (conceptual) table of tunnels on the device. An entry shall be placed in the storage table for each tunnel.
                         ngTunnelEntry 1.3.6.1.4.1.74.1.30.6.1.1 no-access
A (conceptual) entry for one logical tunnel area on the host.
                             ngtuIndex 1.3.6.1.4.1.74.1.30.6.1.1.1 integer32 no-access
A unique value for each logical tunnel contained by the device.
                             ngtuIpsecIface 1.3.6.1.4.1.74.1.30.6.1.1.2 displaystring read-only
The ipsec interface associated with the tunnel.
                             ngtuAuthState 1.3.6.1.4.1.74.1.30.6.1.1.3 integer read-only
An internal state used to indicate the tunnel's current operation. Enumeration: 'attXAuthPending': 12, 'attXAuthFailedPendingResp': 13, 'attSASetup': 17, 'attDialRequestingTok': 20, 'attISAKMPNegPending': 5, 'attRunning': 9, 'attSentLogon': 2, 'attRigAuthPending': 3, 'attRigAuthFailedPendingResp': 25, 'attDialingDone': 16, 'attModeCfgPending': 23, 'attAuthReqAckPending': 7, 'attLogoffPending': 10, 'attXAuthReqPending': 14, 'attAuthReqPending': 8, 'attDialing': 15, 'attQuiesed': 11, 'attReset': 1, 'attRetrySIG': 21, 'attAllTunPingsFailed': 24, 'attDialPendingResponse': 19, 'attNotSetYet': 0, 'attCertLoginPending': 4, 'attRigAuthReqPending': 26, 'attProtocolNegPending': 6, 'attTryNextTun': 22, 'attXAuthTimeout': 18.
                             ngtuState 1.3.6.1.4.1.74.1.30.6.1.1.4 integer read-only
An internal state used to indicate the tunnel's status. This state was created because the ngtuAuthState can change while the tunnel is still up. For example, when the clock is being set. This state is always attTunnelUp when the tunnel is up. Enumeration: 'attTunnelPendingDialConnection': 2, 'attTunnelComingUp': 1, 'attTunnelRestarting': 5, 'attTunnelUp': 3, 'attTunnelDown': 0, 'attTunnelComingDown': 4.
                             ngtuDuration 1.3.6.1.4.1.74.1.30.6.1.1.5 timeticks read-only
How long the tunnel has been up.
                             ngtuEndpoint 1.3.6.1.4.1.74.1.30.6.1.1.6 ipaddress read-only
IP of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up'.
                             ngtuEndpointType 1.3.6.1.4.1.74.1.30.6.1.1.7 integer read-only
Type of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up'. Enumeration: 'none': 0, 'cisco': 9, 'vig': 20, 'nortel': 3, 'gig': 5, 'linuxFrameSig': 4, 'linuxSig': 6.
                             ngtuBulkEncryptMode 1.3.6.1.4.1.74.1.30.6.1.1.8 integer read-only
Bulk encryption mode. Enumeration: 'disabled': 0, 'enabled': 1.
                             ngtuCurrEncryptCeIp 1.3.6.1.4.1.74.1.30.6.1.1.9 ipaddress read-only
Bulk encryption CE address.
                             ngtuEspAlg 1.3.6.1.4.1.74.1.30.6.1.1.10 displaystring read-only
ESP algorithm.
                             ngtuAuthAlg 1.3.6.1.4.1.74.1.30.6.1.1.11 displaystring read-only
AUTH algorithm.
                             ngtuCompressionAlg 1.3.6.1.4.1.74.1.30.6.1.1.12 displaystring read-only
COMPRESSION algorithm.
                             ngtuAuthType 1.3.6.1.4.1.74.1.30.6.1.1.13 integer read-only
Indicates the authentication server that will be used by the tunnel endpoint. Enumeration: 'noTunnelYet': 999, 'customerDirect': 2, 'customerDirectSm': 4, 'serviceManager': 1, 'internetOnly': 0, 'branchOffice': 3.
                             ngtuAuthProt 1.3.6.1.4.1.74.1.30.6.1.1.14 integer read-only
The authentication protocol. Enumeration: 'custRadius': 1, 'none': 0, 'custAxent': 3, 'custSecureID': 2, 'custCert': 4, 'branchSharedSecret': 7, 'custLDAP': 5, 'custInternal': 6, 'agnsManaged': 8.
                             ngtuReasonCode 1.3.6.1.4.1.74.1.30.6.1.1.15 integer read-only
A numeric value that indicates why a tunnel came down. The one exception is tnlAlive, which is sent for the tunnel 'alive' message for a tunnel that is still up. Enumeration: 'eth1Lost': 258, 'powerLost': 503, 'noReasonGiven': 599, 'deviceStatusInactiveWasActive': 506, 'dialIdleTimeout': 509, 'tnlIdleTimeout': 508, 'tnlInitiatedDisco': 226, 'discoButton': 0, 'missedHeartBts': 227, 'tnlAlive': 504, 'maxSessionTimeout': 510, 'eth1Restored': 259, 'noTunnInInetOnlyMode': 507.
                             ngtuServerMgmt 1.3.6.1.4.1.74.1.30.6.1.1.16 integer read-only
AGNS managed or not. Enumeration: 'nonAgnsManaged': 0, 'agnsManaged': 1.
                             ngtuTunInitiator 1.3.6.1.4.1.74.1.30.6.1.1.17 integer read-only
What initiated the tunnel. Enumeration: 'attPersistentLogon': 3, 'attUnknown': 0, 'attVpnctl': 4, 'attAutoLogon': 2, 'attFromUser': 1.
                             ngtuTunMode 1.3.6.1.4.1.74.1.30.6.1.1.18 integer read-only
The tunnel control mode. Enumeration: 'tunnelUserViewOnly': 2, 'tunnelUnknown': 0, 'tunnelHidden': 3, 'tunnelWSSInternet': 5, 'tunnelMaintenance': 4, 'tunnelUserControl': 1.
                             ngtuIPv6Endpoint 1.3.6.1.4.1.74.1.30.6.1.1.19 inetaddressipv6 read-only
IPv6 IP of the endpoint the tunnel is connected to. Populated if the ngtuState is 'up' and IPv6 is in use.
                 ngCosInfo 1.3.6.1.4.1.74.1.30.7
                     ngcoEnabled 1.3.6.1.4.1.74.1.30.7.1 integer read-only
Indicates if COS is enabled or not. Enumeration: 'notActive': 0, 'activeWithoutDscpRemarking': 2, 'activeWithDscpRemarking': 1.
                     ngcoNextTestTime 1.3.6.1.4.1.74.1.30.7.2 displaystring read-only
When the next bandwidth test is scheduled to run. MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when no test is scheduled. The time returned is the local time on the AT&T NetGate. To determine how the AT&T NetGate's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngcoNextTestTimeDAT.
                     ngcoWanMtu 1.3.6.1.4.1.74.1.30.7.3 integer32 read-only
Current WAN interface MTU value.
                     ngcoCurUpstreamBandw 1.3.6.1.4.1.74.1.30.7.4 unsigned32 read-only
Current upstream bandwidth high water mark in use.
                     ngcoCurDownstreamBandw 1.3.6.1.4.1.74.1.30.7.5 unsigned32 read-only
Current downstream bandwidth high water mark in use.
                     ngcoNextTestTimeDAT 1.3.6.1.4.1.74.1.30.7.6 dateandtime read-only
When the next bandwidth test is scheduled to run. Returns January 1 year 0 time 0 when no test is scheduled. NOTE: This entry replaces ngcoNextTestTime.
                     ngcoLastTestTimeDAT 1.3.6.1.4.1.74.1.30.7.7 dateandtime read-only
The date and time of when the last bandwidth test was performed. NOTE: The date and time of high water marks retained after a reboot will return January 1 year 0 time 0 for the time.
                     ngcoLastUpstreamResult 1.3.6.1.4.1.74.1.30.7.8 unsigned32 read-only
The upstream bandwidth measured when the last bandwidth test was performed.
                     ngcoLastDownstreamResult 1.3.6.1.4.1.74.1.30.7.9 unsigned32 read-only
The downstream bandwidth measured when the last bandwidth test was performed.
                 attNetGateMIB 1.3.6.1.4.1.74.1.30.8
The MIB module for the AT&T NetGate.
                     ngMIBConformance 1.3.6.1.4.1.74.1.30.8.1
                         ngMIBCompliances 1.3.6.1.4.1.74.1.30.8.1.1
                             ngBasicComplianceRev 1.3.6.1.4.1.74.1.30.8.1.1.1
The compliance statement for AT&T NetGate entities which implement this MIB module.
                         ngMIBGroups 1.3.6.1.4.1.74.1.30.8.1.2
                             nghwGroup 1.3.6.1.4.1.74.1.30.8.1.2.1
The hardware group.
                             ngifGroup 1.3.6.1.4.1.74.1.30.8.1.2.2
The interface group.
                             ngvlGroup 1.3.6.1.4.1.74.1.30.8.1.2.3
The VLAN group.
                             ngvrGroup 1.3.6.1.4.1.74.1.30.8.1.2.4
The VRRP group.
                             ng3gGroup 1.3.6.1.4.1.74.1.30.8.1.2.5
The 3G group.
                             ngtuGroup 1.3.6.1.4.1.74.1.30.8.1.2.6
The tunnel group.
                             ngcoGroup 1.3.6.1.4.1.74.1.30.8.1.2.7
The COS group.
                             ngfwGroup 1.3.6.1.4.1.74.1.30.8.1.2.8
The firewall group.
                             ngrmGroup 1.3.6.1.4.1.74.1.30.8.1.2.9
The Rogue MAC group.
                             ngdiGroup 1.3.6.1.4.1.74.1.30.8.1.2.10
The dial group.
                             ngdhlGroup 1.3.6.1.4.1.74.1.30.8.1.2.11
The DHCP leases group.
                     ngEvents 1.3.6.1.4.1.74.1.30.8.2
                         ngEventNotification 1.3.6.1.4.1.74.1.30.8.2.0
                             ngevIpConntrackTable 1.3.6.1.4.1.74.1.30.8.2.0.1
Sent if the Firewall Connection table reaches the specified threshold.
                             ngevIpConntrackTableFull 1.3.6.1.4.1.74.1.30.8.2.0.2
Indicates the firewall Connection table has reached capacity.
                             ngevExcessiveDial 1.3.6.1.4.1.74.1.30.8.2.0.3
The device has been in dial backup longer than the allowed threshold.
                             ngevActiveWanIpChanged 1.3.6.1.4.1.74.1.30.8.2.0.4
The IP address associated with the active WAN interface has changed. For example, dial backup was initiated because WAN connectivity was lost. Another example is that a PPPoE connection changed its IP address.
                             ngevRogueMacDetected 1.3.6.1.4.1.74.1.30.8.2.0.5
The unauthorized MAC detection feature is enabled and an unauthorized MAC address was detected.
                             ngevRogueMacNoFile 1.3.6.1.4.1.74.1.30.8.2.0.6
The unauthorized MAC detection feature is enabled and the authorized MAC file doesn't exist.
                             ngevNoTeps 1.3.6.1.4.1.74.1.30.8.2.0.7
The AT&T NetGate cannot bring up a tunnel to any of the tunnel endpoints.
                             ngevDeviceDiscoOrNotFound 1.3.6.1.4.1.74.1.30.8.2.0.8
Sent if the AT&T NetGate profile is not found. If the AT&T NetGate goes too long without finding its device profile then the device will switch its status to discontinued, which will also trigger a trap/inform.
                             ngevTunnelUp 1.3.6.1.4.1.74.1.30.8.2.0.9
Information about the results of a tunnel connection attempt.
                             ngevTunnelDown 1.3.6.1.4.1.74.1.30.8.2.0.10
Information about a tunnel disconnect. The one exception is a tunnel 'alive' message, which is sent for a tunnel that is still up. Tunnel 'alive' messages have a ngtuReasonCode of tnlAlive.
                             ngevDialAutotestFailure 1.3.6.1.4.1.74.1.30.8.2.0.11
The Dial Autotest failed.
                             ngevDeviceReboot 1.3.6.1.4.1.74.1.30.8.2.0.12
Sent when the device reboots. Requestor IP will be set to loopback if an automated process caused the reboot.
                             ngevDeviceShutdown 1.3.6.1.4.1.74.1.30.8.2.0.13
Sent when the device shuts down.
                             ngevSshLogin 1.3.6.1.4.1.74.1.30.8.2.0.14
Sent when a user accesses the device via SSH.
                             ngevDhcpPoolExhausted 1.3.6.1.4.1.74.1.30.8.2.0.15
Sent when a VLAN's DHCP pool is full.
                             ngevForTestingOnly 1.3.6.1.4.1.74.1.30.8.2.0.16
Only for use by QA and development for testing.
                             ngevSecondaryAuthAttempt 1.3.6.1.4.1.74.1.30.8.2.0.17
Sent when a secondary login attempt occurs. Secondary logins are performed when someone tries to ssh into the AT&T NetGate.
                             ngevSwitchUseridAttempt 1.3.6.1.4.1.74.1.30.8.2.0.18
Sent when a user who is ssh'ed into the AT&T NetGate tries to switch to another userid.
                             ngev8200VPortDown 1.3.6.1.4.1.74.1.30.8.2.0.19
Sent when either port 7 or 8 is determined to be not active. Only used by the AT&T NetGate 8200V.
                             ngevCellModemRequired 1.3.6.1.4.1.74.1.30.8.2.0.20
Sent when either the AT&T NetGate boots without a cell modem present or when the AT&T NetGate detects that the cell modem has been removed. The cellular modem must be a supported unit that allows the AT&T NetGate to query its current status.
                         ngEventObjects 1.3.6.1.4.1.74.1.30.8.2.1
                             ngevNetGateMac 1.3.6.1.4.1.74.1.30.8.2.1.1 displaystring no-access
The MAC address associated with this AT&T NetGate.
                             ngevRogueMac 1.3.6.1.4.1.74.1.30.8.2.1.2 displaystring no-access
The MAC address of the unauthorized machine detected when MAC monitoring is enabled.
                             ngevActiveWanIp 1.3.6.1.4.1.74.1.30.8.2.1.3 ipaddress no-access
The IP address of the active WAN interface. When viewing the output of the SNMP tree this can be determined from the interface statistics. However, for traps the active WAN interface might not be used to send the trap (i.e. it could be down the tunnel. Set to zero if not used.
                             ngevIpConntrackMaxPercentage 1.3.6.1.4.1.74.1.30.8.2.1.4 integer32 no-access
An alert will be sent when the ip_conntrack table is within this percentage of the maximum.
                             ngevIpConntrackCurrentPercentage 1.3.6.1.4.1.74.1.30.8.2.1.5 integer32 no-access
The ip_conntrack table is currently at this percentage of the maximum.
                             ngevTimeInDial 1.3.6.1.4.1.74.1.30.8.2.1.6 integer32 no-access
The number of minutes the device has been connected via dial.
                             ngevQueryProblem 1.3.6.1.4.1.74.1.30.8.2.1.7 integer no-access
Used to indicate what type of problem is happening with the device's status. profileNotFound means that a profile for the device was not found on an AT&T Administration Server in any region. discontinuingTheDevice means that the device has gone too long without having a valid profile in any region. bandwNoResults means that a bandwidth test failed and no previous bandwidth test results have been found, which results in the device being marked as discontinued until a bandwidth test works. Enumeration: 'bandwNoResults': 2, 'profileNotFound': 0, 'discontinuingTheDevice': 1.
                             ngevTunConnectionId 1.3.6.1.4.1.74.1.30.8.2.1.8 displaystring no-access
Use to tie this trap to a trap for the tunnel disconnect.
                             ngevTunnelDateAndTime 1.3.6.1.4.1.74.1.30.8.2.1.9 dateandtime no-access
The timestamp from when the tunnel came up, tried to come up, or came down.
                             ngevConnectionType 1.3.6.1.4.1.74.1.30.8.2.1.10 integer no-access
Indicates whether the tunnel is via broadband or dial. Enumeration: 'connTypeBroadband': 0, 'connTypeAgnsDial': 1, 'connTypeOtherIspDial': 2.
                             ngevAccount 1.3.6.1.4.1.74.1.30.8.2.1.11 displaystring no-access
In the tunnel up/down trap it is the customer account used to start the tunnel. In the secondary auth attempt trap it is the account used for the login attempt.
                             ngevUserid 1.3.6.1.4.1.74.1.30.8.2.1.12 displaystring no-access
In the tunnel up/down trap it is the customer userid used to start the tunnel. In the secondary auth attempt trap it is the userid used for the login attempt.
                             ngevTunConReason 1.3.6.1.4.1.74.1.30.8.2.1.13 displaystring no-access
String that shows a message that explains the results of a tunnel connection attempt.
                             ngevDialTestFailReason 1.3.6.1.4.1.74.1.30.8.2.1.14 displaystring no-access
String that shows why the dial test failed.
                             ngevSshSourceIp 1.3.6.1.4.1.74.1.30.8.2.1.15 ipaddress no-access
The IP address of the client that ssh'ed into the device.
                             ngevRequestorIp 1.3.6.1.4.1.74.1.30.8.2.1.16 ipaddress no-access
The IP address of the machine that initiated a particular request (reboot, shutdown, secondary auth attempt, etc.). Will be set to loopback if an automated process caused the reboot.
                             ngevDialTestFailCategory 1.3.6.1.4.1.74.1.30.8.2.1.17 integer no-access
Shows what type of category the dial test failure would be put in. For example, a busy signal would be a warning but a bad password would be an error. Enumeration: 'dialProblemNoCategory': 3, 'dialProblemMessage': 2, 'dialProblemWarning': 1, 'dialProblemError': 0.
                             ngevRogueIp 1.3.6.1.4.1.74.1.30.8.2.1.18 ipaddress no-access
The IP address of the unauthorized machine detected when MAC monitoring is enabled. Set to zero if not used.
                             ngevRogueInterface 1.3.6.1.4.1.74.1.30.8.2.1.19 displaystring no-access
The interface of the unauthorized machine detected when MAC monitoring is enabled.
                             ngevTrapDescription 1.3.6.1.4.1.74.1.30.8.2.1.20 displaystring no-access
For MAC monitoring this is the Service Manager description field. Other traps may use this field for other purposes.
                             ngevLoginResult 1.3.6.1.4.1.74.1.30.8.2.1.21 integer no-access
Specifies the result of the secondary login attempt when someone tries to ssh into the AT&T NetGate. Enumeration: 'failure': 0, 'success': 1.
                             ngevNewLocalID 1.3.6.1.4.1.74.1.30.8.2.1.22 displaystring no-access
The userid that the user became after their secondary login attempt was successful. Secondary logins are performed when someone tries to ssh into the AT&T NetGate. The userid that the user became (or tried to become) for their switch user attempt.
                             ngevOldLocalID 1.3.6.1.4.1.74.1.30.8.2.1.23 displaystring no-access
The userid that was in use when the user made their switch user attempt.
                             ngevMaxTimeInDialUntilAlert 1.3.6.1.4.1.74.1.30.8.2.1.24 timeticks no-access
The max number of minutes the device can be connected via dial without a trap being sent for excessive dial. Once this maximum is reached a trap will be sent.
                             ngevPortDown 1.3.6.1.4.1.74.1.30.8.2.1.25 integer32 no-access
An individual port that is currently not active. Only used by the AT&T NetGate 8200V.
                             ngevIPv6ActiveWanIp 1.3.6.1.4.1.74.1.30.8.2.1.26 inetaddressipv6 no-access
The IP address of the active IPv6 WAN interface. When viewing the output of the SNMP tree this can be determined from the interface statistics. However, for traps the active WAN interface might not be used to send the trap (i.e. it could be down the tunnel. Set to zero if not used.
                             ngevIPv6RogueIp 1.3.6.1.4.1.74.1.30.8.2.1.27 inetaddressipv6 no-access
The IPv6 IP address of the unauthorized machine detected when MAC monitoring is enabled. Set to zero if not used.
                             ngevIPv6RequestorIp 1.3.6.1.4.1.74.1.30.8.2.1.28 inetaddressipv6 no-access
The IPv6 IP address of the machine that initiated a particular request (reboot, shutdown, secondary auth attempt, etc.). Will be set to loopback if an automated process caused the reboot.
                             ngevCardNotFoundTime 1.3.6.1.4.1.74.1.30.8.2.1.29 dateandtime no-access
The timestamp that indicates when the AT&T NetGate noted that the required cellular card was missing.
                             ngevVPNServiceIPv4Address 1.3.6.1.4.1.74.1.30.8.2.1.30 ipaddress no-access
The VPN Service Address assigned for this tunnel connetino. Will be not set if this is an IPv6 tunnel or the tunnel did not come up.
                             ngevVPNServiceIPv6Address 1.3.6.1.4.1.74.1.30.8.2.1.31 inetaddressipv6 no-access
The VPN Service Address assigned for this tunnel connetino. Will be not set if this is an IPv4 tunnel or the tunnel did not come up.
                             ngevTunConReasonNUM 1.3.6.1.4.1.74.1.30.8.2.1.32 integer32 read-only
A numeric value that indicates the results of a tunnel connection attempt.
                         ngEventConformance 1.3.6.1.4.1.74.1.30.8.2.2
                             ngEventCompliances 1.3.6.1.4.1.74.1.30.8.2.2.1
                                 ngevBasicComplianceRev 1.3.6.1.4.1.74.1.30.8.2.2.1.1
The compliance statement for AT&T NetGate entities which implement this MIB module.
                             ngEventGroups 1.3.6.1.4.1.74.1.30.8.2.2.2
                                 ngevNotificationsGroup 1.3.6.1.4.1.74.1.30.8.2.2.2.1
The event notifications
                                 ngevObjectsGroup 1.3.6.1.4.1.74.1.30.8.2.2.2.2
The event ojects.
                 ngFirewallInfo 1.3.6.1.4.1.74.1.30.9
                     ngFirewallTable 1.3.6.1.4.1.74.1.30.9.1 no-access
The (conceptual) table of firewall tables on the device. An entry shall be placed in the storage table for each table.
                         ngFirewallTableEntry 1.3.6.1.4.1.74.1.30.9.1.1 no-access
A (conceptual) entry for one logical firewall table area on the host.
                             ngfwTableIndex 1.3.6.1.4.1.74.1.30.9.1.1.1 integer32 no-access
A unique value for each logical firewall table contained by the device.
                             ngfwTableName 1.3.6.1.4.1.74.1.30.9.1.1.2 displaystring read-only
The name of this table.
                             ngfwTableNumberOfChains 1.3.6.1.4.1.74.1.30.9.1.1.3 integer32 read-only
The number of chains in this particular table.
                     ngFirewallChainTable 1.3.6.1.4.1.74.1.30.9.2 no-access
The (conceptual) chain of firewall chains on the device. An entry shall be placed in the storage chain for each chain.
                         ngFirewallChainEntry 1.3.6.1.4.1.74.1.30.9.2.1 no-access
A (conceptual) entry for one logical firewall chain area on the host.
                             ngfwChainIndex 1.3.6.1.4.1.74.1.30.9.2.1.1 integer32 no-access
A unique value for each logical firewall chain contained by the device.
                             ngfwChainTableIndex 1.3.6.1.4.1.74.1.30.9.2.1.2 integer32 read-only
Shows what table this chain belongs to. Corresponds to ngfwTableIndex in ngFirewallTable.
                             ngfwChainName 1.3.6.1.4.1.74.1.30.9.2.1.3 displaystring read-only
The name of this chain.
                             ngfwChainsNumberOfRules 1.3.6.1.4.1.74.1.30.9.2.1.4 integer32 read-only
The number of rules in this particular chain.
                     ngFirewallRuleTable 1.3.6.1.4.1.74.1.30.9.3 no-access
The (conceptual) table of firewall rules on the device. An entry shall be placed in the storage rule for each rule.
                         ngFirewallRuleEntry 1.3.6.1.4.1.74.1.30.9.3.1 no-access
A (conceptual) entry for one logical firewall rule area on the host.
                             ngfwRuleIndex 1.3.6.1.4.1.74.1.30.9.3.1.1 integer32 no-access
A unique value for each logical firewall rule contained by the device.
                             ngfwRuleTableIndex 1.3.6.1.4.1.74.1.30.9.3.1.2 integer32 read-only
Shows what table this rule belongs to. Corresponds to ngfwTableIndex in ngFirewallTable.
                             ngfwRuleChainIndex 1.3.6.1.4.1.74.1.30.9.3.1.3 integer32 read-only
Shows what chain this rule belongs to. Corresponds to ngfwChainIndex in ngFirewallChainTable.
                             ngfwRulePackets 1.3.6.1.4.1.74.1.30.9.3.1.4 unsigned32 read-only
Total packets for this rule.
                             ngfwRuleBytes 1.3.6.1.4.1.74.1.30.9.3.1.5 unsigned32 read-only
Total bytes for this rule.
                             ngfwRuleTarget 1.3.6.1.4.1.74.1.30.9.3.1.6 displaystring read-only
The rule target.
                             ngfwRuleProtocol 1.3.6.1.4.1.74.1.30.9.3.1.7 displaystring read-only
The rule protocol.
                             ngfwRuleInIface 1.3.6.1.4.1.74.1.30.9.3.1.8 displaystring read-only
The rule input interface.
                             ngfwRuleOutIface 1.3.6.1.4.1.74.1.30.9.3.1.9 displaystring read-only
The rule output interface.
                             ngfwRuleSrcIp 1.3.6.1.4.1.74.1.30.9.3.1.10 ipaddress read-only
The rule source IP.
                             ngfwRuleSrcMask 1.3.6.1.4.1.74.1.30.9.3.1.11 integer32 read-only
The rule source mask in CIDR-compliant format.
                             ngfwRuleDstIp 1.3.6.1.4.1.74.1.30.9.3.1.12 ipaddress read-only
The rule destination IP.
                             ngfwRuleDstMask 1.3.6.1.4.1.74.1.30.9.3.1.13 integer32 read-only
The rule destination mask in CIDR-compliant format.
                             ngfwRuleMisc 1.3.6.1.4.1.74.1.30.9.3.1.14 displaystring read-only
The rule MISC section.
                     ngfwIpConntrackNumEntries 1.3.6.1.4.1.74.1.30.9.4 integer32 read-only
The number entries in the ip_conntrack file.
                     ngfwIpConntrackMaxNumEntries 1.3.6.1.4.1.74.1.30.9.5 integer32 read-only
The maximum number of entries in the ip_conntrack file.
                     ngIPv6FirewallTable 1.3.6.1.4.1.74.1.30.9.6 no-access
The (conceptual) table of IPv6 firewall tables on the device. An entry shall be placed in the storage table for each table.
                         ngIPv6FirewallTableEntry 1.3.6.1.4.1.74.1.30.9.6.1 no-access
A (conceptual) entry for one logical IPv6 firewall table area on the host.
                             ngfwIPv6TableIndex 1.3.6.1.4.1.74.1.30.9.6.1.1 integer32 no-access
A unique value for each logical IPv6 firewall table contained by the device.
                             ngfwIPv6TableName 1.3.6.1.4.1.74.1.30.9.6.1.2 displaystring read-only
The name of this table.
                             ngfwIPv6TableNumberOfChains 1.3.6.1.4.1.74.1.30.9.6.1.3 integer32 read-only
The number of chains in this particular table.
                     ngIPv6FirewallChainTable 1.3.6.1.4.1.74.1.30.9.7 no-access
The (conceptual) chain of IPv6 firewall chains on the device. An entry shall be placed in the storage chain for each chain.
                         ngIPv6FirewallChainEntry 1.3.6.1.4.1.74.1.30.9.7.1 no-access
A (conceptual) entry for one logical IPv6 firewall chain area on the host.
                             ngfwIPv6ChainIndex 1.3.6.1.4.1.74.1.30.9.7.1.1 integer32 no-access
A unique value for each logical IPv6 firewall chain contained by the device.
                             ngfwIPv6ChainTableIndex 1.3.6.1.4.1.74.1.30.9.7.1.2 integer32 read-only
Shows what table this chain belongs to. Corresponds to ngfwIPv6TableIndex in ngIPv6FirewallTable.
                             ngfwIPv6ChainName 1.3.6.1.4.1.74.1.30.9.7.1.3 displaystring read-only
The name of this chain.
                             ngfwIPv6ChainsNumberOfRules 1.3.6.1.4.1.74.1.30.9.7.1.4 integer32 read-only
The number of rules in this particular chain.
                     ngIPv6FirewallRuleTable 1.3.6.1.4.1.74.1.30.9.8 no-access
The (conceptual) table of IPv6 firewall rules on the device. An entry shall be placed in the storage rule for each rule.
                         ngIPv6FirewallRuleEntry 1.3.6.1.4.1.74.1.30.9.8.1 no-access
A (conceptual) entry for one logical IPv6 firewall rule area on the host.
                             ngfwIPv6RuleIndex 1.3.6.1.4.1.74.1.30.9.8.1.1 integer32 no-access
A unique value for each logical IPv6 firewall rule contained by the device.
                             ngfwIPv6RuleTableIndex 1.3.6.1.4.1.74.1.30.9.8.1.2 integer32 read-only
Shows what table this rule belongs to. Corresponds to ngfwIPv6TableIndex in ngIPv6FirewallTable.
                             ngfwIPv6RuleChainIndex 1.3.6.1.4.1.74.1.30.9.8.1.3 integer32 read-only
Shows what chain this rule belongs to. Corresponds to ngfwIPv6ChainIndex in ngIPv6FirewallChainTable.
                             ngfwIPv6RulePackets 1.3.6.1.4.1.74.1.30.9.8.1.4 unsigned32 read-only
Total packets for this rule.
                             ngfwIPv6RuleBytes 1.3.6.1.4.1.74.1.30.9.8.1.5 unsigned32 read-only
Total bytes for this rule.
                             ngfwIPv6RuleTarget 1.3.6.1.4.1.74.1.30.9.8.1.6 displaystring read-only
The rule target.
                             ngfwIPv6RuleProtocol 1.3.6.1.4.1.74.1.30.9.8.1.7 displaystring read-only
The rule protocol.
                             ngfwIPv6RuleInIface 1.3.6.1.4.1.74.1.30.9.8.1.8 displaystring read-only
The rule input interface.
                             ngfwIPv6RuleOutIface 1.3.6.1.4.1.74.1.30.9.8.1.9 displaystring read-only
The rule output interface.
                             ngfwIPv6RuleSrcIp 1.3.6.1.4.1.74.1.30.9.8.1.10 inetaddressipv6 no-access
The rule source IP. Not used and set to all zeroes for IPv4 firewall output.
                             ngfwIPv6RuleSrcMask 1.3.6.1.4.1.74.1.30.9.8.1.11 integer32 read-only
The rule source mask in CIDR-compliant format. Not used and set to all zeroes for IPv4 firewall output.
                             ngfwIPv6RuleDstIp 1.3.6.1.4.1.74.1.30.9.8.1.12 inetaddressipv6 no-access
The rule source IP. Not used and set to all zeroes for IPv4 firewall output.
                             ngfwIPv6RuleDstMask 1.3.6.1.4.1.74.1.30.9.8.1.13 integer32 read-only
The rule source mask in CIDR-compliant format. Not used and set to all zeroes for IPv4 firewall output.
                             ngfwIPv6RuleMisc 1.3.6.1.4.1.74.1.30.9.8.1.14 displaystring read-only
The rule MISC section.
                 ngRogueMacInfo 1.3.6.1.4.1.74.1.30.10
                       ngRogueMacStatus 1.3.6.1.4.1.74.1.30.10.1 integer read-only
Inidicates whether or not Rogue MAC detection has been enabled in Service Manager. Enumeration: 'disabled': 0, 'enabled': 1.
                       ngRogueMacTable 1.3.6.1.4.1.74.1.30.10.2 no-access
The (conceptual) table of rogue MACs detected by the device. An entry shall be placed in the storage table for each rogue MAC.
                           ngRogueMacEntry 1.3.6.1.4.1.74.1.30.10.2.1 no-access
A (conceptual) entry for one logical rogue MAC area on the host.
                               ngrmIndex 1.3.6.1.4.1.74.1.30.10.2.1.1 integer32 no-access
A unique value for each logical rogue MAC detected by the device.
                               ngrmMac 1.3.6.1.4.1.74.1.30.10.2.1.2 displaystring read-only
The MAC address of this detected rogue MAC. One entry that is zeroed out is returned when there are no rogue MACs detected.
                               ngrmTimestamp 1.3.6.1.4.1.74.1.30.10.2.1.3 displaystring read-only
The date and time of when this rogue MAC was detected. Returned as a regular string in the format MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when there are no rogue MACs detected. The time returned is the local time on the AT&T NetGate. To determine how the AT&T NetGate's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngrmTimestampDAT.
                               ngrmIface 1.3.6.1.4.1.74.1.30.10.2.1.4 displaystring read-only
The interface this rogue MAC was detected on. One entry that with a value of 'NONE' and a msg is returned when there are no rogue MACs detected.
                               ngrmTimestampDAT 1.3.6.1.4.1.74.1.30.10.2.1.5 dateandtime read-only
The date and time of when this rogue MAC was detected. Returns January 1 year 0 time 0 when there are no rogue MACs detected or the time is unknown. NOTE: This entry replaces ngrmTimestamp.
                 ngDialInfo 1.3.6.1.4.1.74.1.30.11
                       ngdiPhoneNum 1.3.6.1.4.1.74.1.30.11.1 displaystring read-only
The full phone number that will be dialed by the AT&T NetGate. This also includes dial prefix information. For example, the AT&T NetGate might have to dial the number nine and then a comma to access an outside line. The nine and the comma will be included in this entry.
                       ngdiLastTestResult 1.3.6.1.4.1.74.1.30.11.2 integer read-only
The result of the last dial test. If no dial test has been performed yet then 'failure' is returned. If a dial test is not needed because dial is currently up then 'success' is returned. Enumeration: 'failure': 0, 'success': 1.
                       ngdiLastTestCompleteTime 1.3.6.1.4.1.74.1.30.11.3 displaystring read-only
The approximate time the last dial test completed given in the format MM/DD/YYYY HH:MM:SS. Returns '00/00/0000 00:00:00' when no test is scheduled. or when no test has run yet. If the dial connection is currently in use then the dial test is not needed (since dial is obviously already working). ngdiLastTestCompleteTime is simply updated to the recent time whent the AT&T NetGate last verified that the dial connection was still up. The time returned is the local time on the AT&T NetGate. To determine how the AT&T NetGate's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry is made obsolete by ngdiLastTestCompleteTimeDAT.
                       ngdiDialTestFailCategory 1.3.6.1.4.1.74.1.30.11.4 integer no-access
Shows what type of category the dial test failure would be put in. For example, a busy signal would return dialProblemWarning but a bad password would return dialProblemError. If a dial test is not needed because dial is currently up then dialProblemMessage is returned. Enumeration: 'dialProblemNoCategory': 3, 'dialProblemMessage': 2, 'dialProblemWarning': 1, 'dialProblemError': 0.
                       ngdiDialTestFailReason 1.3.6.1.4.1.74.1.30.11.5 displaystring no-access
String that shows why the dial test failed. If the test was successful or the dial connection is currently up then 'success' is returned.
                       ngdiLastTestCompleteTimeDAT 1.3.6.1.4.1.74.1.30.11.6 dateandtime read-only
If the dial connection is currently in use then the dial test is not needed (since dial is obviously already working). ngdiLastTestCompleteTimeDAT is simply updated to the recent time whent the AT&T NetGate last verified that the dial connection was still up. Returns January 1 year 0 time 0 when no test is scheduled or when no test has run yet. The time returned is the local time on the AT&T NetGate. To determine how the AT&T NetGate's local time relates to UTC view the following OIDs: nghwUtcOffset (current UTC offset), nghwDstAllowed (daylight saving time allowed), nghwDstActive (daylight savings time active). NOTE: This entry replaces ngdiLastTestCompleteTime.
                       ngdiSecondaryPhoneNum 1.3.6.1.4.1.74.1.30.11.7 displaystring read-only
Specifies the secondary phone number to be tried for Dial Backup in case the primary Dial Backup phone number is not available.
                 ngDhcpLeaseInfo 1.3.6.1.4.1.74.1.30.12
                       ngDhcpLeaseTable 1.3.6.1.4.1.74.1.30.12.1 no-access
The (conceptual) table of all current, active DHCP leases on the device. An entry shall be placed in the storage table for each DHCP lease.
                           ngDhcpLeaseEntry 1.3.6.1.4.1.74.1.30.12.1.1 no-access
A (conceptual) entry for one logical DHCP lease on the host.
                               ngdhlIndex 1.3.6.1.4.1.74.1.30.12.1.1.1 integer32 no-access
A unique value for each logical DHCP lease contained by the device.
                               ngdhlLeaseAddr 1.3.6.1.4.1.74.1.30.12.1.1.2 ipaddress read-only
The IP address associated with an indivdual DHCP lease.
                               ngdhlMac 1.3.6.1.4.1.74.1.30.12.1.1.3 displaystring read-only
The MAC address associated with an indivdual DHCP lease.
                               ngdhlHostname 1.3.6.1.4.1.74.1.30.12.1.1.4 displaystring read-only
The hostname associated with an indivdual DHCP lease.
                               ngdhlPort 1.3.6.1.4.1.74.1.30.12.1.1.5 integer32 read-only
The physical port (if valid) on the device associated with an indivdual DHCP lease.
                               ngdhlVlanId 1.3.6.1.4.1.74.1.30.12.1.1.6 integer32 read-only
The VLAN ID on the device associated with an indivdual DHCP lease.