Wellfleet-SYNC-MIB: View SNMP OID List / Download MIB

VENDOR: WELLFLEET


 Home MIB: Wellfleet-SYNC-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 wfSyncTable 1.3.6.1.4.1.18.3.4.5 no-access
SYNC line record
     wfSyncEntry 1.3.6.1.4.1.18.3.4.5.1 no-access
An entry in the SYNC table
         wfSyncDelete 1.3.6.1.4.1.18.3.4.5.1.1 integer read-write
Create/Delete parameter Enumeration: 'deleted': 2, 'created': 1.
         wfSyncDisable 1.3.6.1.4.1.18.3.4.5.1.2 integer read-write
Enable/Disable parameter Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncState 1.3.6.1.4.1.18.3.4.5.1.3 integer read-only
Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced with NOTPRES. Enumeration: 'lineloopbofltest': 19, 'up': 1, 'remoteloop': 8, 'down': 2, 'init': 3, 'notpres': 20, 'holddown': 7, 'notpresent': 5, 'wait': 4, 'dsrwait': 6.
         wfSyncSlot 1.3.6.1.4.1.18.3.4.5.1.4 integer read-only
Instance ID Slot, filled in by driver
         wfSyncConnector 1.3.6.1.4.1.18.3.4.5.1.5 integer read-only
Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connector'. Where 'module' is defined in attribute 86 and 'connector' is defined in attribute 78 of this table. For non-ASN platforms this attribute is the physical connector number on the slot.
         wfSyncCct 1.3.6.1.4.1.18.3.4.5.1.6 integer read-write
CCT number for this line instance
         wfSyncBofl 1.3.6.1.4.1.18.3.4.5.1.7 integer read-write
breath of life parameter Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncBoflTmo 1.3.6.1.4.1.18.3.4.5.1.8 integer read-write
breath of life timeout in seconds
         wfSyncMtu 1.3.6.1.4.1.18.3.4.5.1.9 integer read-write
MTU parameter, this is buffer size for SYNC media, fixed
         wfSyncMadr 1.3.6.1.4.1.18.3.4.5.1.10 octet string read-only
Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.
         wfSyncPromiscuous 1.3.6.1.4.1.18.3.4.5.1.11 integer read-write
The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address are received Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncXid 1.3.6.1.4.1.18.3.4.5.1.12 integer read-write
XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncClkSource 1.3.6.1.4.1.18.3.4.5.1.13 integer read-write
Tx/Rx clock source is either internally or external generated. Enumeration: 'internal': 1, 'external': 2.
         wfSyncClkSpeed 1.3.6.1.4.1.18.3.4.5.1.14 integer read-write
Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected. Enumeration: 'clk2mb': 2500000, 'clk125k': 125000, 'clk19200b': 19230, 'clk32000b': 32051, 'clk833k': 833333, 'clk5mb': 5000000, 'clk1mb': 1250000, 'clk1200b': 1200, 'clk230k': 227272, 'clk2400b': 2401, 'clk625k': 625000, 'clk38400b': 38461, 'clk64k': 64102, 'clk420k': 416666, 'clk9600b': 9615, 'clk4800b': 4807, 'clk7200b': 7204, 'clk56k': 56818.
         wfSyncSignalMode 1.3.6.1.4.1.18.3.4.5.1.15 integer read-write
The signal mode parameter indicates the line paramter balanced or unbalanced. Enumeration: 'balanced': 1, 'unbalanced': 2.
         wfSyncRtsEnable 1.3.6.1.4.1.18.3.4.5.1.16 integer read-write
Note: In KG84 support, RTS has a different meaning Enumeration: 'disabled': 2, 'enabled': 1, 'kg84aenabled': 3.
         wfSyncBurstCount 1.3.6.1.4.1.18.3.4.5.1.17 integer read-write
Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. The default is always 8 short word bursts (ENABLED). There are only two cases in which this attribute should be changed. Case 1: In certain cases with DSDE and DSE link modules when one or both of the ethernet ports are suffering from excessive TxUflo or RxOflo errors, the BurstCount of one or both SYNC interfaces can be set to single short word bursts (DISABLED). The only modules for which this may be necessary are the DSDE (5430 - Dual Sync, Dual Enet) (module ID 112) and the DSE (5420 - Dual Sync, Single Enet) (module ID 116). If after making the change, the TxUflo or RxOflo errors persist on the ethernet or this SYNC interface starts to get UnderFlowTx or OverFlowRx errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. Case 2: When a SYNC interface on an mk5025 based Link Module is getting UnderFlowTx or OverFlowRx errors while running at bandwidths greater than 2Mbps, the errors may be eliminated by setting this attribute to unlimited burst mode (UNLIMITED). If after making the change, the errors persist or the same errors start on another SYNC interface or one of the ethernet interfaces on the same module starts to get TxUflo or RxOflo errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. For 6Mbps full duplex operation, this attribute will most likely need to be set to UNLIMITED and all other interfaces on this module will most likely have to be deconfigured. Enumeration: 'disabled': 2, 'unlimited': 3, 'enabled': 1.
         wfSyncService 1.3.6.1.4.1.18.3.4.5.1.18 integer read-write
Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the LAPB protocol service. Enumeration: 'llc1': 2, 'transparent': 1, 'llc2': 3.
         wfSyncRetryCount 1.3.6.1.4.1.18.3.4.5.1.19 integer read-write
The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer. This parameter is equal to the N2 counter in ICB.
         wfSyncLinkIdleTimer 1.3.6.1.4.1.18.3.4.5.1.20 integer read-write
The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed in seconds.
         wfSyncRetryTimer 1.3.6.1.4.1.18.3.4.5.1.21 integer read-write
The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control frames are sent at the expiration of this timer value. The frames will be resent up to retry count (N2) at which time the link will be disconnected.
         wfSyncExtendedAddress 1.3.6.1.4.1.18.3.4.5.1.22 integer read-write
This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine the length of address field in octets. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncExtendedAddressForce 1.3.6.1.4.1.18.3.4.5.1.23 integer read-write
When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. Usefull only in Transparent Mode. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncExtendedControl 1.3.6.1.4.1.18.3.4.5.1.24 integer read-write
This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead of modulo 8. The control field of U frames remains one octet in length. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncExtendedControlForce 1.3.6.1.4.1.18.3.4.5.1.25 integer read-write
This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Transparent Mode. (LLC1) Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncConnectAttempts 1.3.6.1.4.1.18.3.4.5.1.26 integer read-write
This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 service.
         wfSyncWindowSizeTx 1.3.6.1.4.1.18.3.4.5.1.27 integer read-write
The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode.
         wfSyncWindowSizeTxExtc 1.3.6.1.4.1.18.3.4.5.1.28 integer read-write
The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode.
         wfSyncMinFrameSpace 1.3.6.1.4.1.18.3.4.5.1.29 integer read-write
The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames.
         wfSyncLocalAddress 1.3.6.1.4.1.18.3.4.5.1.30 integer read-write
The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. Enumeration: 'addressdce': 1, 'addressexplicit': 7, 'addressdte': 3.
         wfSyncRemoteAddress 1.3.6.1.4.1.18.3.4.5.1.31 integer read-write
The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. Enumeration: 'addressdce': 1, 'addressexplicit': 7, 'addressdte': 3.
         wfSyncPassThruLocalMadr 1.3.6.1.4.1.18.3.4.5.1.32 octet string read-write
48 bit MAC address of Local end of Sync Passthru circuit
         wfSyncPassThruRemoteMadr 1.3.6.1.4.1.18.3.4.5.1.33 octet string read-write
48 bit MAC address of Remote end of Sync Passthru circuit
         wfSyncWanProtocol 1.3.6.1.4.1.18.3.4.5.1.34 integer read-write
WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. Enumeration: 'passthr': 2, 'atm': 9, 'sw': 8, 'aot': 12, 'standard': 1, 'switch': 7, 'ppp': 3, 'framerelay': 5, 'sdlc': 11, 'x25': 6, 'lapb': 10, 'smds': 4.
         wfSyncCrcSize 1.3.6.1.4.1.18.3.4.5.1.35 integer read-write
CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC Enumeration: 'crc16bit': 1, 'crc32bit': 2.
         wfSyncRxOctets 1.3.6.1.4.1.18.3.4.5.1.36 counter read-only
Number of octets received without error
         wfSyncRxFrames 1.3.6.1.4.1.18.3.4.5.1.37 counter read-only
Number of frames received without error
         wfSyncTxOctets 1.3.6.1.4.1.18.3.4.5.1.38 counter read-only
Number of octets transmitted without error
         wfSyncTxFrames 1.3.6.1.4.1.18.3.4.5.1.39 counter read-only
Number of frames transmitted without error
         wfSyncRxErrors 1.3.6.1.4.1.18.3.4.5.1.40 counter read-only
Number of receive errors
         wfSyncTxErrors 1.3.6.1.4.1.18.3.4.5.1.41 counter read-only
Number of transmission errors
         wfSyncLackRescRx 1.3.6.1.4.1.18.3.4.5.1.42 counter read-only
Number of Rx frames dropped due to lack of buffer resources
         wfSyncLackRescTx 1.3.6.1.4.1.18.3.4.5.1.43 counter read-only
Number of frames clipped in driver's transmit routine due to transmit congestion.
         wfSyncUnderFlowTx 1.3.6.1.4.1.18.3.4.5.1.44 counter read-only
Number of transmission underflows, device FIFO went empty before next DMA request was granted.
         wfSyncRejectsTx 1.3.6.1.4.1.18.3.4.5.1.45 counter read-only
For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in Async mode: Number of frames that grew, due to escaping, larger than a buffer
         wfSyncRejectsRx 1.3.6.1.4.1.18.3.4.5.1.46 counter read-only
For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a non-matching address For the quicsync driver in Async mode: Number of frames received that did not fit within a buffer
         wfSyncOverFlowRx 1.3.6.1.4.1.18.3.4.5.1.47 counter read-only
Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available.
         wfSyncFramesIncompRx 1.3.6.1.4.1.18.3.4.5.1.48 counter read-only
Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors.
         wfSyncBadFramesRx 1.3.6.1.4.1.18.3.4.5.1.49 counter read-only
Number of bad receive frames, caused by FCS errors or non octet aligned.
         wfSyncFrameRejectsRx 1.3.6.1.4.1.18.3.4.5.1.50 counter read-only
Number of Frame Rejects received
         wfSyncRuntsRx 1.3.6.1.4.1.18.3.4.5.1.51 counter read-only
Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception.
         wfSyncT1Timeouts 1.3.6.1.4.1.18.3.4.5.1.52 counter read-only
Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of the number of timeouts.
         wfSyncMemoryErrors 1.3.6.1.4.1.18.3.4.5.1.53 counter read-only
Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us.
         wfSyncMediaType 1.3.6.1.4.1.18.3.4.5.1.54 integer read-write
Media type selection is provided via this parameter Enumeration: 'isdnleased': 7, 'default': 1, 't1': 2, 'raisedtr': 4, 'bri': 6, 'hayes': 8, 'e1': 3, 'v25bis': 5.
         wfSyncCfgTxQueueLength 1.3.6.1.4.1.18.3.4.5.1.55 integer read-write
Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size.
         wfSyncCfgRxQueueLength 1.3.6.1.4.1.18.3.4.5.1.56 integer read-write
Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size.
         wfSyncTxQueueLength 1.3.6.1.4.1.18.3.4.5.1.57 integer read-only
Current Transmit Queue Length.
         wfSyncRxQueueLength 1.3.6.1.4.1.18.3.4.5.1.58 integer read-only
Current Receive Queue Length.
         wfSyncRxReplenMisses 1.3.6.1.4.1.18.3.4.5.1.59 counter read-only
Number of packet buffer misses while attempting to replenish driver receive ring.
         wfSyncStartUpMode 1.3.6.1.4.1.18.3.4.5.1.60 integer read-write
Initiation of link level for LLC2 running LAPB Enumeration: 'active': 1, 'passive': 2.
         wfSyncIdleRRFrames 1.3.6.1.4.1.18.3.4.5.1.61 integer read-write
Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent. Enumeration: 'on': 1, 'off': 2.
         wfSyncMultilineMode 1.3.6.1.4.1.18.3.4.5.1.62 integer read-write
This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard. Enumeration: 'secondary': 4, 'primary': 3, 'monitor': 2, 'standard': 1.
         wfSyncBODExamPeriod 1.3.6.1.4.1.18.3.4.5.1.63 integer read-write
This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second
         wfSyncBODFullThreshold 1.3.6.1.4.1.18.3.4.5.1.64 integer read-write
This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested.
         wfSyncBODRecoverThreshold 1.3.6.1.4.1.18.3.4.5.1.65 integer read-write
This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in order for the BOD circuit to revert back to the primary line only. This value should be set to less than one half the value of wfSyncBODFullThreshold to avoid toggling the secondary.
         wfSyncBODPeriodsToFail 1.3.6.1.4.1.18.3.4.5.1.66 integer read-write
This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested.
         wfSyncKG84ACycle 1.3.6.1.4.1.18.3.4.5.1.67 integer read-write
Monitor sample time in milliseconds Enumeration: 'cycle50ms': 50, 'cycle10ms': 10, 'cycle500ms': 500, 'cycle100ms': 100, 'cycle5ms': 5, 'cycle25ms': 25, 'cycle200ms': 200.
         wfSyncKG84ASyncLossInterval 1.3.6.1.4.1.18.3.4.5.1.68 integer read-write
timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization Enumeration: 'num2cycles': 2, 'num10cycles': 10, 'num5cycles': 5, 'num50cycles': 50, 'num100cycles': 100, 'num200cycles': 200, 'num500cycles': 500, 'num25cycles': 25.
         wfSyncKG84ARemoteResyncWait 1.3.6.1.4.1.18.3.4.5.1.69 integer read-write
when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request Enumeration: 'num2cycles': 2, 'num10cycles': 10, 'num5cycles': 5, 'num50cycles': 50, 'num100cycles': 100, 'num200cycles': 200, 'num500cycles': 500, 'num25cycles': 25.
         wfSyncKG84ASyncPulse 1.3.6.1.4.1.18.3.4.5.1.70 integer read-write
interval to pulse KG84a SYNC signal, in milliseconds
         wfSyncKG84AResyncs 1.3.6.1.4.1.18.3.4.5.1.71 integer read-only
number of KG84 resyncs performed
         wfSyncKG84AResyncsDetected 1.3.6.1.4.1.18.3.4.5.1.72 integer read-only
number of KG84 resyncs detected
         wfSyncKG84ABsu 1.3.6.1.4.1.18.3.4.5.1.73 integer read-only
value taken from mk5025 sync chip control block
         wfSyncKG84AState 1.3.6.1.4.1.18.3.4.5.1.74 integer read-only
state of sync Enumeration: 'remote': 3, 'idle': 1, 'local': 2, 'sync': 4.
         wfSyncKG84AOkFrames 1.3.6.1.4.1.18.3.4.5.1.75 integer read-only
count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected
         wfSyncPollingEnable 1.3.6.1.4.1.18.3.4.5.1.76 integer read-write
Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. If disabled, the DSR lead is ignored. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncBackupPool 1.3.6.1.4.1.18.3.4.5.1.77 integer read-write
Backup pool id containing this line driver
         wfSyncDemandPool 1.3.6.1.4.1.18.3.4.5.1.78 integer read-write
Dial on demand pool id containing this line driver
         wfSyncLineNumber 1.3.6.1.4.1.18.3.4.5.1.79 integer read-write
line number for this line instance
         wfSyncHoldDownTime 1.3.6.1.4.1.18.3.4.5.1.80 integer read-write
Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a backup configuration and it is a dirty line
         wfSyncNetworkType 1.3.6.1.4.1.18.3.4.5.1.81 integer read-write
Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip revision C04. If a customer must be NET2 compliant and is using an MK5025 chip revision C03, the C03 option must be used. Enumeration: 'c03': 3, 'net2': 2, 'gosip': 1.
         wfSyncActiveCct 1.3.6.1.4.1.18.3.4.5.1.82 integer read-only
Active CCT number for this line instance
         wfSyncCableType 1.3.6.1.4.1.18.3.4.5.1.83 integer read-write
Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem
         wfSyncRxDropPackets 1.3.6.1.4.1.18.3.4.5.1.84 counter read-only
Number of Rx packets dropped by driver.
         wfSyncTxDropPackets 1.3.6.1.4.1.18.3.4.5.1.85 counter read-only
Number of Tx packets dropped by driver.
         wfSyncModule 1.3.6.1.4.1.18.3.4.5.1.86 integer read-only
Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. Enumeration: 'four': 4, 'three': 3, 'two': 2, 'one': 1.
         wfSyncActualConnector 1.3.6.1.4.1.18.3.4.5.1.87 integer read-only
Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. Enumeration: 'seven': 7, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.
         wfSyncLineCoding 1.3.6.1.4.1.18.3.4.5.1.88 integer read-write
Line Coding for sync interface. Can be either NRZ or NRZI. Enumeration: 'nrzimark': 3, 'nrz': 1, 'nrzi': 2.
         wfSyncLastChange 1.3.6.1.4.1.18.3.4.5.1.89 timeticks read-only
The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second) since the network management portion of the system was last re-initialized. Usually the time since boot.
         wfSyncOutQLen 1.3.6.1.4.1.18.3.4.5.1.90 gauge read-only
The instantaneous current length of the output packet queue (in packets).
         wfSyncRemoteLpbkDetection 1.3.6.1.4.1.18.3.4.5.1.91 integer read-write
This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is receiving its own BOFL packets and will bring the interface down assuming that somewhere down stream the link has been put into loopback. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncLastState 1.3.6.1.4.1.18.3.4.5.1.92 integer read-only
The state which the driver was in prior to the most recent re-initialization. Enumeration: 'up': 1, 'remoteloop': 8, 'down': 2, 'init': 3, 'notpres': 20, 'holddown': 7, 'notpresent': 5, 'wait': 4, 'dsrwait': 6.
         wfSyncExternalClkSpeed 1.3.6.1.4.1.18.3.4.5.1.93 integer read-write
External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supplied clock. Depending on the protocols configured on this interface, this value may control internal decision making within the router. In some cases, router software uses this attribute for route selection. If Priority Queuing is configured, it chooses queue depths based on this attribute. This attribute has no effect when Internal clocking is configured.
         wfSyncBChannelOverride 1.3.6.1.4.1.18.3.4.5.1.94 integer read-write
For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instance id, but the user may override that here, which gives the ability of connecting the B Channel to specific SCC's. Enumeration: 'default': 3, 'bchannel1': 1, 'bchannel2': 2, 'floatingb': 4.
         wfSyncBChannel 1.3.6.1.4.1.18.3.4.5.1.95 integer read-only
Indicates which B Channel is running Enumeration: 'bchannel1': 1, 'bchannel2': 2.
         wfSyncForceIFTF 1.3.6.1.4.1.18.3.4.5.1.96 integer read-write
Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular channel. For SDLC Lines, DEFAULT and FORCE_HDLC_FLAGS both result in HDLC Flags (0x7E) as the fill character. FLAGSTREAMING will cause the fill character to alternate between Flags (0x7E) and Idles (0xFF), depending upon the current state of the line. For ISDN BRI Lines, DEFAULT, FORCE IDLES and FLAGSTREAMING all result in Idles (0xFF) as the fill character. For all other line types, DEFAULT, FORCE HDLC FLAGS and FLAGSTREAMING all result in HDLC Flags (0x7E) as the fill character. Leave this field at the default unless required for the attached device. The AS/400 high speed serial controller requires the use of FLAGSTREAMING for error-free operation. Enumeration: 'default': 1, 'forceidles': 3, 'forcehdlcflags': 2, 'flagstreaming': 4.
         wfSyncPriority 1.3.6.1.4.1.18.3.4.5.1.97 integer read-write
Used by dial/switched services to assign priority of lines within the same demand or backup pool
         wfSyncTurboBofl 1.3.6.1.4.1.18.3.4.5.1.98 integer read-write
DEBUG parameter - Turbo bofl enabled or disabled Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncBoflNum 1.3.6.1.4.1.18.3.4.5.1.99 integer read-write
DEBUG parameter - Number of breath of life packets per breath of life
         wfSyncBoflLen 1.3.6.1.4.1.18.3.4.5.1.100 integer read-write
DEBUG parameter - breath of life packet length
         wfSyncTurboBoflMisses 1.3.6.1.4.1.18.3.4.5.1.101 integer read-only
DEBUG parameter - breath of life allocation failures
         wfSyncTurboBoflInvocations 1.3.6.1.4.1.18.3.4.5.1.102 integer read-only
DEBUG parameter - breath of life invocations
         wfSyncBandwidthOnDemandPool 1.3.6.1.4.1.18.3.4.5.1.103 integer read-write
Bandwidth pool id containing this line driver
         wfSyncBODRecoverPeriodsToPass 1.3.6.1.4.1.18.3.4.5.1.104 integer read-write
This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line congested. It is used for recovery. That is, once a line is declared as congested, this is the number of consecutive examination periods where the queue depth is below the recovery threshold value required to delare that the line is no longer congested.
         wfSyncBODHistory 1.3.6.1.4.1.18.3.4.5.1.105 displaystring read-only
DEBUG parameter - This is the SBOD history buffer.
         wfSyncBODDebugFlag 1.3.6.1.4.1.18.3.4.5.1.106 integer read-write
DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD.
         wfSyncBChRateAdaption 1.3.6.1.4.1.18.3.4.5.1.107 integer read-write
This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line mode. This attribute specifies the piece of ISDN line's bandwidth which data from this driver will occupy. Enumeration: 'adaption128k': 2, 'adaption64k': 1.
         wfSyncBChActualRateAdaption 1.3.6.1.4.1.18.3.4.5.1.108 integer read-only
Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line or dial-up mode. This attribute indicates the speed of this B-channel. It also specifies their bit positions for the case of 56K selections. Enumeration: 'adaption128k': 2, 'adaption64k': 1, 'adaption56kmsb': 3, 'adaption56klsb': 4.
         wfSyncWanType 1.3.6.1.4.1.18.3.4.5.1.109 integer read-write
This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface. Enumeration: 'asynchronous': 2, 'synchronous': 1, 'pasynchronous': 3.
         wfSyncAsyncBaudRate 1.3.6.1.4.1.18.3.4.5.1.110 integer read-write
Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe. Enumeration: 'baudrate64k': 64000, 'baudrate56k': 57600, 'baudrate76k': 76800, 'baudrate28800b': 28800, 'baudrate14400b': 14400, 'baudrate1200b': 1200, 'baudrate4800b': 4800, 'baudrate12000b': 12000, 'baudrate19200b': 19200, 'baudrate96k': 96000, 'baudrate115k': 115200, 'baudrate7200b': 7200, 'baudrate38k': 38400, 'baudrate9600b': 9600, 'baudrate2400b': 2400.
         wfSyncCfgAsyncCmndMaxIdles 1.3.6.1.4.1.18.3.4.5.1.111 integer read-write
Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode.
         wfSyncAsyncCmndMaxIdles 1.3.6.1.4.1.18.3.4.5.1.112 integer read-only
Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode.
         wfSyncCfgAsyncDataMaxIdles 1.3.6.1.4.1.18.3.4.5.1.113 integer read-write
Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode.
         wfSyncAsyncDataMaxIdles 1.3.6.1.4.1.18.3.4.5.1.114 integer read-only
Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode.
         wfSyncFramesAbortTx 1.3.6.1.4.1.18.3.4.5.1.115 counter read-only
Number of frames where CTS was lost during transmission.
         wfSyncPasyncParityType 1.3.6.1.4.1.18.3.4.5.1.116 integer read-write
Type of parity chosen for Polled Async Enumeration: 'even': 2, 'high': 3, 'none': 5, 'odd': 1, 'low': 4.
         wfSyncPasyncCharacterLength 1.3.6.1.4.1.18.3.4.5.1.117 integer read-write
Number of data bits chosen for Polled Async Enumeration: 'eight': 8, 'seven': 7, 'six': 6, 'five': 5.
         wfSyncPasyncStopLength 1.3.6.1.4.1.18.3.4.5.1.118 integer read-write
Number of stop bits chosen for Polled Async Enumeration: 'two': 2, 'one': 1.
         wfSyncPasyncBaudRate 1.3.6.1.4.1.18.3.4.5.1.119 integer read-write
Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe. Enumeration: 'baudrate64k': 64000, 'baudrate19200b': 19200, 'baudrate150b': 150, 'baudrate76k': 76800, 'baudrate28800b': 28800, 'baudrate14400b': 14400, 'baudrate1200b': 1200, 'baudrate4800b': 4800, 'baudrate300b': 300, 'baudrate12000b': 12000, 'baudrate600b': 600, 'baudrate96k': 96000, 'baudrate56k': 57600, 'baudrate115k': 115200, 'baudrate7200b': 7200, 'baudrate38k': 38400, 'baudrate9600b': 9600, 'baudrate2400b': 2400.
         wfSyncLocalConnectionState 1.3.6.1.4.1.18.3.4.5.1.120 integer read-only
The state of the cable at the router end. Enumeration: 'down': 2, 'unknown': 3, 'up': 1.
         wfSyncRemoteConnectionState 1.3.6.1.4.1.18.3.4.5.1.121 integer read-only
The state of the cable at the device end. Enumeration: 'down': 2, 'unknown': 4, 'up': 1, 'devicestreaming': 3.
         wfSyncTimeSlotAssignment 1.3.6.1.4.1.18.3.4.5.1.122 displaystring read-only
Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by the channel assigned to the FT1 card. It contains a list of the timeslots from 1 to 32 for the G.703 card.
         wfSyncEiaStatus 1.3.6.1.4.1.18.3.4.5.1.123 integer read-only
The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted, it is marked as a 1. If not asserted, it is marked as a 0. The state of each signal will be updated every second. Bits 0-15 are reserved for actual signal state. Bits 16-31 are reserved for indicating toggling of the signal. Toggling signals are indicated as a 1. Signals not toggling are indicated with a 0. The following signals are defined and monitored: The bit definition as as follows with bit #0 being the LSB. * signal status - bits 0-15 * bit 0 = TXD transmit data 1 = RXD receive data 2 = RTS request to send 3 = CTS clear to send 4 = DSR data set ready 5 = DCD data carrier detect 6 = TXC transmit clock 7 = RXC receive clock 8 = DTR data terminal ready. * signal toggle status bits 16-31 * bit 16 = TXD transmit data 17 = RXD receive data 18 = RTS request to send 19 = CTS clear to send 20 = DSR data set ready 21 = DCD data carrier detect 22 = TXC transmit clock 23 = RXC receive clock 24 = DTR data terminal ready. Enumeration: 'dcdToggled': 2097152, 'txcToggled': 4194304, 'ctsToggled': 524288, 'cts': 8, 'dtrToggled': 16777216, 'txc': 64, 'dcd': 32, 'txd': 1, 'dsr': 16, 'rxd': 2, 'rtsToggled': 262144, 'dsrToggled': 1048576, 'rts': 4, 'dtr': 256, 'txdToggled': 65536, 'rxdToggled': 131072, 'rxc': 128, 'rxcToggled': 8388608.
         wfSyncEiaStatusReset 1.3.6.1.4.1.18.3.4.5.1.124 integer read-write
Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status. Enumeration: 'reset': 1, 'noaction': 21.
         wfSyncUcastMap 1.3.6.1.4.1.18.3.4.5.1.125 integer read-write
Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames. Enumeration: 'disabled': 2, 'enabled': 1.
         wfSyncAsyncCfgMaxIdleTimer 1.3.6.1.4.1.18.3.4.5.1.126 integer read-write
Determines if Async Max Idle Timer should be based on the baudrate or on the time needed to receive three characters. Enumeration: 'baudrate': 1, 'threechars': 2.