Wellfleet-NAT-MIB: View SNMP OID List / Download MIB

VENDOR: WELLFLEET


 Home MIB: Wellfleet-NAT-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC, Wellfleet-COMMON-MIB

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 wfNatBase 1.3.6.1.4.1.18.3.5.3.2.7.1
     wfNatBaseDelete 1.3.6.1.4.1.18.3.5.3.2.7.1.1 integer read-write
'This value determines whether NAT is configured' Enumeration: 'deleted': 2, 'created': 1.
     wfNatBaseDisable 1.3.6.1.4.1.18.3.5.3.2.7.1.2 integer read-write
'The administrative status of NAT in the router. The value 'enabled' denotes that the NAT Process is active on at least one interface; 'disabled' disables it on all interfaces.' Enumeration: 'disabled': 2, 'enabled': 1.
     wfNatBaseState 1.3.6.1.4.1.18.3.5.3.2.7.1.3 integer read-only
'The state of NAT' Enumeration: 'down': 3, 'init': 2, 'up': 1, 'not-present': 4.
     wfNatBaseSoloistSlotMask 1.3.6.1.4.1.18.3.5.3.2.7.1.4 gauge read-write
Slot mask for which slots the soloist gate is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots.
     wfNatBaseSoloistSlot 1.3.6.1.4.1.18.3.5.3.2.7.1.5 integer read-only
Slot on which NAT soloist gate is running. Slots can be 1-14. Default is zero.
     wfNatBaseLogMask 1.3.6.1.4.1.18.3.5.3.2.7.1.6 integer read-write
A parameter to specify which NAT log messages should be logged. Each bit represents a message as defined below. A 1 in that bit location means to log it and a 0 means not to put that log message in the log. Changing this value will NOT restart NAT, but will take effct immediately(if there are any messages to be logged. bit 31 bit 0 +---------------------------------------+ | | +---------------------------------------+ NAT_DBG_MIB_LOG 0x00000001 NAT_DBG_IP_LOG 0x00000002 NAT_DBG_FWD_LOG 0x00000004 NAT_DBG_MAPPING_LOG 0x00000008 NAT_DBG_AGING_LOG 0x00000010 NAT_DBG_SYNCH_LOG 0x00000020
     wfNatBaseMapTimeout 1.3.6.1.4.1.18.3.5.3.2.7.1.7 integer read-write
This controls whether or not the dynamic mapping table entries are aged out when unused. Enumeration: 'disabled': 2, 'enabled': 1.
     wfNatBaseMapMaxTimeout 1.3.6.1.4.1.18.3.5.3.2.7.1.8 integer read-write
The maximum time in seconds before unused NAT mapping table entries are deleted. This timeout or aging does not apply to static mapping entries.
     wfNatBaseMapDynMapsCount 1.3.6.1.4.1.18.3.5.3.2.7.1.9 gauge read-only
Number of Dynamic Mappings in the dymanic mapping table
     wfNatBaseFtpSessionCount 1.3.6.1.4.1.18.3.5.3.2.7.1.10 gauge read-only
Number of FTP sessions detected on this box translated by NAT
     wfNatBaseNto1TrTotCount 1.3.6.1.4.1.18.3.5.3.2.7.1.11 gauge read-only
Total number of active Nto1 translation counts on the box.
     wfNatBaseSynchronization 1.3.6.1.4.1.18.3.5.3.2.7.1.12 integer read-write
The administrative status of NAT Synchronization in the router. The value `enabled' denotes that the NAT Synchronization is active and is synchronizing with the peer specified in noraml conditions.; `disabled' disables it on the box and all the peer connections will be teared down.' Enumeration: 'disabled': 2, 'enabled': 1.
     wfNatBaseSynRouterID 1.3.6.1.4.1.18.3.5.3.2.7.1.13 ipaddress read-write
This represents the Router Identifier for NAT Synchronization Only. This is used to detect the duplicate TCP connection between peers. The value of it can be any integer which is unique between all the NAT Syn peers this router has. An IP Address of one of the router interfaces can be used as the RouterID. Changing the value will result into breaking and reconnecting using new ID with all the peers.'
     wfNatBaseSynPort 1.3.6.1.4.1.18.3.5.3.2.7.1.14 integer read-write
This represents the TCP port on which the connection requests from the peers will be accepted. When NAT Synchronization Protocol comes up, it will open a listen connection for this port number. This attribute value has to be the same on all the peers that want to make the TCP connection.'
     wfNatBaseSynKeepAlvInterval 1.3.6.1.4.1.18.3.5.3.2.7.1.15 integer read-write
Idle session timeout period, in seconds. If an established TCP connection remains inactive for this interval, KEEPALIVE messages will be sent to the peer (if the Keepalive Timer is non-zero). Setting the Idle Timer to zero disables the keepalive feature.
     wfNatBaseSynKeepAlvTimer 1.3.6.1.4.1.18.3.5.3.2.7.1.16 integer read-write
KEEPALIVE retransmit timeout period, in seconds. This is the interval at which unacknowledged KEEPALIVE messages will be retransmitted. If the Idle Timer is set to zero, this timer ignored. If the Idle Timer is non-zero and this timer IS zero, no KEEPALIVEs are sent and the session is terminated upon expiration of the Idle Timer.
     wfNatBaseSynKeepAlvRetries 1.3.6.1.4.1.18.3.5.3.2.7.1.17 integer read-write
Number of unacknowledged KEEPALIVE messages retransmitted before the TCP session is terminated. If this count is set to zero, only one KEEPALIVE message will be sent.
     wfNatBaseLocalToLocalEnable 1.3.6.1.4.1.18.3.5.3.2.7.1.18 integer read-write
Allow forwarding of traffic from one local NAT interface to another local NAT interface. Enumeration: 'disabled': 2, 'enabled': 1.
     wfNatBaseInstallUniPrivAddr 1.3.6.1.4.1.18.3.5.3.2.7.1.19 integer read-write
This MIB was added in BayRS 14.20 to address a compatibility issue concerning non-DNS NAT translations when upgrading from a pre-14.20 NAT configuration to a 14.20 or greater version of BayRS software. This MIB should remain enabled. Disabling this MIB will cause Uni-directional NAT to no longer function correctly on the router. Enumeration: 'disabled': 2, 'enabled': 1.
 wfNatAddrRangeTable 1.3.6.1.4.1.18.3.5.3.2.7.2 no-access
Table of address ranges that have been designated as the set of external apparent addresses that are to be mapped in place of internal actual addresses. These addresses would be the non-public reigistered addresses.
     wfNatAddrRangeEntry 1.3.6.1.4.1.18.3.5.3.2.7.2.1 no-access
'Information describing each of the available address ranges.'
         wfNatAddrRangeDelete 1.3.6.1.4.1.18.3.5.3.2.7.2.1.1 integer read-write
'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry.' Enumeration: 'deleted': 2, 'created': 1.
         wfNatAddrRangeDisable 1.3.6.1.4.1.18.3.5.3.2.7.2.1.2 integer read-write
'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry.' Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatAddrRangeAddress 1.3.6.1.4.1.18.3.5.3.2.7.2.1.3 ipaddress read-write
'The IP beginning address of this range entry.
         wfNatAddrRangePrefixLen 1.3.6.1.4.1.18.3.5.3.2.7.2.1.4 integer read-write
'The IP address mask that in conjunction with the start address defines the address range of the entry.'
 wfNatLocalAddrRangeTable 1.3.6.1.4.1.18.3.5.3.2.7.3 no-access
Table of address ranges that have been designated as the set of local addresses that are to be mapped via NAT.
     wfNatLocalAddrRangeEntry 1.3.6.1.4.1.18.3.5.3.2.7.3.1 no-access
'Information describing each of the available address ranges.'
         wfNatLocalAddrRangeDelete 1.3.6.1.4.1.18.3.5.3.2.7.3.1.1 integer read-write
'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry.' Enumeration: 'deleted': 2, 'created': 1.
         wfNatLocalAddrRangeDisable 1.3.6.1.4.1.18.3.5.3.2.7.3.1.2 integer read-write
'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry.' Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatLocalAddrRangeAddress 1.3.6.1.4.1.18.3.5.3.2.7.3.1.3 ipaddress read-write
'The IP beginning address of this range entry.
         wfNatLocalAddrRangePrefixLen 1.3.6.1.4.1.18.3.5.3.2.7.3.1.4 integer read-write
'The IP address mask that in conjunction with the start address defines the address range of the entry.'
         wfNatLocalAddrRangeNto1Addr 1.3.6.1.4.1.18.3.5.3.2.7.3.1.5 ipaddress read-write
Nto1 translation address used for this range.
 wfNatStaticMapTable 1.3.6.1.4.1.18.3.5.3.2.7.4 no-access
'This table creates instances of pre-defined NAT mappings.'
     wfNatStaticMapEntry 1.3.6.1.4.1.18.3.5.3.2.7.4.1 no-access
'A single local-to-global address mapping.'
         wfNatStaticMapDelete 1.3.6.1.4.1.18.3.5.3.2.7.4.1.1 integer read-write
'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a static address mapping entry.' Enumeration: 'deleted': 2, 'created': 1.
         wfNatStaticMapDisable 1.3.6.1.4.1.18.3.5.3.2.7.4.1.2 integer read-write
'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a static address mapping entry.' Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatStaticMapLocalAddress 1.3.6.1.4.1.18.3.5.3.2.7.4.1.3 ipaddress read-write
'The local or private address of the mapping pair.'
         wfNatStaticMapGlobalAddress 1.3.6.1.4.1.18.3.5.3.2.7.4.1.4 ipaddress read-write
'The global or external address of the mapping pair.'
         wfNatStaticMapProtocol 1.3.6.1.4.1.18.3.5.3.2.7.4.1.5 integer read-write
'The IP protocol of the mapping pair.'
         wfNatStaticMapLocalPort 1.3.6.1.4.1.18.3.5.3.2.7.4.1.6 integer read-write
'The local UDP or TCP port of the mapping pair. This will only be relevent if the protocol is either UDP or TCP.'
         wfNatStaticMapGlobalPort 1.3.6.1.4.1.18.3.5.3.2.7.4.1.7 integer read-write
'The global UDP or TCP port of the mapping pair. This will only be relevent if the protocol is either UDP or TCP.'
 wfNatMapTable 1.3.6.1.4.1.18.3.5.3.2.7.5 no-access
'This table defines the current set of address mappings that are in effect.'
     wfNatMapEntry 1.3.6.1.4.1.18.3.5.3.2.7.5.1 no-access
         wfNatMapLocalAddress 1.3.6.1.4.1.18.3.5.3.2.7.5.1.1 ipaddress read-only
'The local address of the mapping pair.'
         wfNatMapGlobalAddress 1.3.6.1.4.1.18.3.5.3.2.7.5.1.2 ipaddress read-only
'The global address of the mapping pair.'
         wfNatMapProtocol 1.3.6.1.4.1.18.3.5.3.2.7.5.1.3 integer read-only
'The IP protocol of the mapping pair.'
         wfNatMapLocalPort 1.3.6.1.4.1.18.3.5.3.2.7.5.1.4 integer read-only
'When the mapping is for a TCP connection, this denotes the TCP port number on the local side.'
         wfNatMapGlobalPort 1.3.6.1.4.1.18.3.5.3.2.7.5.1.5 integer read-only
'When the mapping is for a TCP connection, this denotes the TCP port number on the global side.'
         wfNatMapTxCount 1.3.6.1.4.1.18.3.5.3.2.7.5.1.6 counter read-only
'Number of packets for this mapping pair that have been mapped from the local to the global network.'
         wfNatMapRxCount 1.3.6.1.4.1.18.3.5.3.2.7.5.1.7 counter read-only
'Number of packets for this mapping pair that have been mapped from the global to the local network.'
         wfNatMapTimeout 1.3.6.1.4.1.18.3.5.3.2.7.5.1.8 counter read-only
'The time in seconds since this mapping entry was last used. This is used to age out mapping entries.'
         wfNatMapMode 1.3.6.1.4.1.18.3.5.3.2.7.5.1.9 integer read-only
This is the bit mask representing the type of this mapping. Each bit specifies the type as follows: The mapping could be only ONE of the foolowing three... 0x01000000 - This mapping is origianted on this router, i.e. this NAT router performed the translation 0x02000000 - This mapping is learned from the peer, i.e. this translation was learned from the peer using NAT Synchronization feature. 0x04000000 - This mapping is owned, i.e. it was originally learned from peer, but this router received traffic which used this mapping. ...and only ONE of the following three. 0x00000010 - This mapping is the STATIC mapping. 0x00000020 - This mapping is Dynamic(1 to 1) mapping. 0x00000040 - This mapping is N to 1 mapping.
 wfNatIfTable 1.3.6.1.4.1.18.3.5.3.2.7.6 no-access
'The set of interface that are participating in the NAT protocol.'
     wfNatIfEntry 1.3.6.1.4.1.18.3.5.3.2.7.6.1 no-access
'An single instance of a NAT interface entry.'
         wfNatIfDelete 1.3.6.1.4.1.18.3.5.3.2.7.6.1.1 integer read-write
This variable determines in a NAT Interface has been configured on the router. Enumeration: 'deleted': 2, 'created': 1.
         wfNatIfDisable 1.3.6.1.4.1.18.3.5.3.2.7.6.1.2 integer read-write
'The NAT interface's administrative status. The value 'enabled' denotes that NAT has been configured on the interface. The value 'disabled' denotes that the interface is not running NAT.' Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatIfIpAddress 1.3.6.1.4.1.18.3.5.3.2.7.6.1.3 ipaddress read-only
The IP address of this NAT interface.
         wfNatIfCircuit 1.3.6.1.4.1.18.3.5.3.2.7.6.1.4 integer read-write
The circuit number of this interface.
         wfNatIfType 1.3.6.1.4.1.18.3.5.3.2.7.6.1.5 integer read-write
Denotes the type of NAT interface being defined. Enumeration: 'biDirectional': 3, 'uniDirOutbound': 2, 'uniDirInbound': 1.
         wfNatIfState 1.3.6.1.4.1.18.3.5.3.2.7.6.1.6 integer read-only
'The state of NAT on this interface' Enumeration: 'down': 2, 'init': 3, 'up': 1.
         wfNatIfTxCount 1.3.6.1.4.1.18.3.5.3.2.7.6.1.7 counter read-only
Number of packets mapped over this interface from the local to the global network.'
         wfNatIfRxCount 1.3.6.1.4.1.18.3.5.3.2.7.6.1.8 counter read-only
Number of packets mapped over this interface from the global to the local network.'
         wfNatIfPktDropCount 1.3.6.1.4.1.18.3.5.3.2.7.6.1.9 counter read-only
Number of packets dropped on this interface
         wfNatIfDomain 1.3.6.1.4.1.18.3.5.3.2.7.6.1.10 displaystring read-write
When wfNatIfType is set to biDirectional, specifies the Address Domain Name that this interface is connected to, otherwise set to null.
 wfNatSynPeerTable 1.3.6.1.4.1.18.3.5.3.2.7.7 no-access
The Nat Synchronization Peer table contains configuration and statistical information regarding this router's NAT peers
     wfNatSynPeerEntry 1.3.6.1.4.1.18.3.5.3.2.7.7.1 no-access
An entry in the NAT Synchronization-Peer table
         wfNatSynPeerDelete 1.3.6.1.4.1.18.3.5.3.2.7.7.1.1 integer read-write
Create/Delete: if set to delete, this instance of the peer entry is deleted, which results into the termination of peer connection. Enumeration: 'deleted': 2, 'created': 1.
         wfNatSynPeerDisable 1.3.6.1.4.1.18.3.5.3.2.7.7.1.2 integer read-write
Enable/Disable: controls whether the peer connection is enabled or disabled, disabling this results into the termination of TCP connection Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatSynPeerState 1.3.6.1.4.1.18.3.5.3.2.7.7.1.3 integer read-only
the administrative state of the peer connection Enumeration: 'down': 4, 'established': 3, 'init': 2, 'not-present': 1.
         wfNatSynPeerConnType 1.3.6.1.4.1.18.3.5.3.2.7.7.1.4 integer read-only
the type of the TCP connection with the peer, whether this connection is accepted from the peer or it was actively initialted by this router to the peer. Enumeration: 'active': 1, 'passive': 2.
         wfNatSynPeerRouterID 1.3.6.1.4.1.18.3.5.3.2.7.7.1.5 ipaddress read-only
A unique non-zero RouterID of the peer that this router is expecting from the connection This is also the instance of the Peer Entry.
         wfNatSynPeerAddress 1.3.6.1.4.1.18.3.5.3.2.7.7.1.6 ipaddress read-write
the IP Address of the peer, where the router will send a connect request
         wfNatSynPeerTransSent 1.3.6.1.4.1.18.3.5.3.2.7.7.1.7 integer read-only
The number of translations sent to this peer by the router
         wfNatSynPeerTransRecd 1.3.6.1.4.1.18.3.5.3.2.7.7.1.8 integer read-only
The number of translations received from this peer by the router
 wfNatAddressRangeTable 1.3.6.1.4.1.18.3.5.3.2.7.8 no-access
Table of address ranges. This table was replaced by wfNatSrcAddressFilterTable and wfNatTranslationPoolTable
     wfNatAddressRangeEntry 1.3.6.1.4.1.18.3.5.3.2.7.8.1 no-access
Information describing each of the available address ranges.
         wfNatAddressRangeDelete 1.3.6.1.4.1.18.3.5.3.2.7.8.1.1 integer read-write
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry. Enumeration: 'deleted': 2, 'created': 1.
         wfNatAddressRangeDisable 1.3.6.1.4.1.18.3.5.3.2.7.8.1.2 integer read-write
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry. Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatAddressRangeAddress 1.3.6.1.4.1.18.3.5.3.2.7.8.1.3 ipaddress read-only
The IP beginning address of this range entry.
         wfNatAddressRangePrefixLen 1.3.6.1.4.1.18.3.5.3.2.7.8.1.4 integer read-only
The number of contiguous bits set in the IP address mask which are used to define the address range of the entry.
         wfNatAddressRangeIndex 1.3.6.1.4.1.18.3.5.3.2.7.8.1.5 integer read-only
A unique value for this entry in wfNatAddressRangeTable.
         wfNatAddressRangeNto1Addr 1.3.6.1.4.1.18.3.5.3.2.7.8.1.6 ipaddress read-write
When wfNatAddressRangeType is set to srcAddrFilter, specifies the N-to-1 translation address used for this range, otherwise set to zero.
         wfNatAddressRangeType 1.3.6.1.4.1.18.3.5.3.2.7.8.1.7 integer read-write
Denotes the type of address range being defined. sourceAddrFilter: a range of IP addresses used to detect packets which need traditional NAT forwarding. translationPool: for traditional NAT forwarding, a range of IP addresses from which translation addresses are picked. domainSrcAddrFilter: a range of IP addresses used to detect domain specific packets which need domain specific NAT forwarding. domainTransPool: for domain specific NAT forwarding, a range of IP addresses from which domain specific translation addresses are picked. Enumeration: 'translationPool': 2, 'domainSrcAddrFilter': 3, 'domainTransPool': 4, 'sourceAddrFilter': 1.
         wfNatAddressRangeDomain 1.3.6.1.4.1.18.3.5.3.2.7.8.1.8 displaystring read-write
When wfNatAddressRangeType is set to domainSrcAddrFilter or domainTransPool, specifies the Address Domain Name that this address range is valid for, otherwise set to null.
         wfNatAddressRangeTransPool 1.3.6.1.4.1.18.3.5.3.2.7.8.1.9 integer read-write
This attribute is only valid for the wfNatAddressRangeType as domainSrcAddrFilter(3). The value of this attribute decides where to get the translation address for this range from. This could be either the translation Pool defined for the inbound domain or the outbound domain for the packet in question. Enumeration: 'inbound': 1, 'outbound': 2.
         wfNatAddressRangeStaticNextHop 1.3.6.1.4.1.18.3.5.3.2.7.8.1.10 ipaddress read-write
The IP address of the next hop of this range entry.
         wfNatAddressRangeUnnumCct 1.3.6.1.4.1.18.3.5.3.2.7.8.1.11 integer read-write
This Nat Address range over the unnumbered interface.
 wfNatStaticMappingTable 1.3.6.1.4.1.18.3.5.3.2.7.9 no-access
`This table creates instances of pre-defined NAT translations.'
     wfNatStaticMappingEntry 1.3.6.1.4.1.18.3.5.3.2.7.9.1 no-access
A single original source address to translated address translation.
         wfNatStaticMappingDelete 1.3.6.1.4.1.18.3.5.3.2.7.9.1.1 integer read-write
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a static address translation entry. Enumeration: 'deleted': 2, 'created': 1.
         wfNatStaticMappingDisable 1.3.6.1.4.1.18.3.5.3.2.7.9.1.2 integer read-write
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a static address translation entry. Enumeration: 'disabled': 2, 'enabled': 1.
         wfNatStaticMappingOrigAddress 1.3.6.1.4.1.18.3.5.3.2.7.9.1.3 ipaddress read-write
The original (un-translated) address of the translation.
         wfNatStaticMappingTransAddress 1.3.6.1.4.1.18.3.5.3.2.7.9.1.4 ipaddress read-only
The translated address of the translation.
         wfNatStaticMappingProtocol 1.3.6.1.4.1.18.3.5.3.2.7.9.1.5 integer read-only
The IP protocol of the translation. Example values are 6 for TCP, and 17 for UDP.
         wfNatStaticMappingOrigPort 1.3.6.1.4.1.18.3.5.3.2.7.9.1.6 integer read-write
The original (domain specific) UDP or TCP port of the translation. This will only be relevent if the protocol is either UDP or TCP.
         wfNatStaticMappingTransPort 1.3.6.1.4.1.18.3.5.3.2.7.9.1.7 integer read-only
The translated UDP or TCP port of the translation. This will only be relevent if the protocol is either UDP or TCP.
         wfNatStaticMappingInDomain 1.3.6.1.4.1.18.3.5.3.2.7.9.1.8 displaystring read-write
This attribute specifies the name of the address domain that this source translation shall be valid for. In other words, this translation shall only be valid for source addresses coming inbound from this domain.
         wfNatStaticMappingOutDomain 1.3.6.1.4.1.18.3.5.3.2.7.9.1.9 displaystring read-write
This attribute specifies the name of the outbound address domain that this translation will be valid for. In other words, this translation only applies to translations that will be forwarded out into this address domain.
         wfNatStaticMappingStaticNextHop 1.3.6.1.4.1.18.3.5.3.2.7.9.1.10 ipaddress read-write
The IP address of the next hop of this static entry.
         wfNatStaticMappingUnnumCct 1.3.6.1.4.1.18.3.5.3.2.7.9.1.11 integer read-write
This Nat static translation over the unnumbered interface.
 wfNatMappingTable 1.3.6.1.4.1.18.3.5.3.2.7.10 no-access
This table defines the current set of address translations that are in effect.
       wfNatMappingEntry 1.3.6.1.4.1.18.3.5.3.2.7.10.1 no-access
A single original source address to translated address translation.
           wfNatMappingOrigAddress 1.3.6.1.4.1.18.3.5.3.2.7.10.1.1 ipaddress read-only
The original (un-translated) address of the translation.
           wfNatMappingTransAddress 1.3.6.1.4.1.18.3.5.3.2.7.10.1.2 ipaddress read-only
The translated address of the translation.
           wfNatMappingProtocol 1.3.6.1.4.1.18.3.5.3.2.7.10.1.3 integer read-only
`The IP protocol of the translation.'
           wfNatMappingOrigPort 1.3.6.1.4.1.18.3.5.3.2.7.10.1.4 integer read-only
When the translation is for a TCP connection, this denotes the original TCP port number.
           wfNatMappingTransPort 1.3.6.1.4.1.18.3.5.3.2.7.10.1.5 integer read-only
When the translation is for a TCP connection, this denotes the translated TCP port number.
           wfNatMappingTxCount 1.3.6.1.4.1.18.3.5.3.2.7.10.1.6 counter read-only
Number of packets forwarded by NAT using this translation.
           wfNatMappingRxCount 1.3.6.1.4.1.18.3.5.3.2.7.10.1.7 counter read-only
Number of packets received by NAT using this translation.
           wfNatMappingTimeout 1.3.6.1.4.1.18.3.5.3.2.7.10.1.8 counter read-only
The time in seconds since this translation entry was last used. This is used to age out translation entries.
           wfNatMappingMode 1.3.6.1.4.1.18.3.5.3.2.7.10.1.9 integer read-only
This is the bit mask representing the type of this translation. Each bit specifies the type as follows: The translation could be only ONE of the following three... 0x01000000 - This translation is origianted on this router, i.e. this NAT router performed the translation. 0x02000000 - This translation is learned from the peer, i.e. this translation was learned from the peer using NAT Synchronization feature. 0x04000000 - This translation is owned, i.e. it was originally learned from peer, but this router received traffic which used this translation. ...and only ONE of the following three. 0x00000010 - This translation is the STATIC translation. 0x00000020 - This translation is Dynamic(1 to 1) translation. 0x00000040 - This translation is N to 1 translation.
           wfNatMappingInDomain 1.3.6.1.4.1.18.3.5.3.2.7.10.1.10 displaystring read-only
This attribute specifies the name of the address domain that this source translation shall be valid for. In ther words, this translation shall only be valid for source addresses coming inbound from this domain.
           wfNatMappingOutDomain 1.3.6.1.4.1.18.3.5.3.2.7.10.1.11 displaystring read-only
This attribute specifies the name of the outbound address domain that this translation will be valid for. In other words, this translation only applies to translations that will be forwarded out into this address domain.
 wfNatIntfTable 1.3.6.1.4.1.18.3.5.3.2.7.11 no-access
'The list of configured NAT interfaces.'
       wfNatIntfEntry 1.3.6.1.4.1.18.3.5.3.2.7.11.1 no-access
'A NAT interface description.'
           wfNatIntfDelete 1.3.6.1.4.1.18.3.5.3.2.7.11.1.1 integer read-write
This variable determines if a NAT Interface has been configured on the router. Enumeration: 'deleted': 2, 'created': 1.
           wfNatIntfDisable 1.3.6.1.4.1.18.3.5.3.2.7.11.1.2 integer read-write
'The NAT interface's administrative status. The value 'enabled' denotes that NAT has been configured on the interface. The value 'disabled' denotes that the interface is not running NAT.' Enumeration: 'disabled': 2, 'enabled': 1.
           wfNatIntfIpAddress 1.3.6.1.4.1.18.3.5.3.2.7.11.1.3 ipaddress read-only
The IP address of this NAT interface.
           wfNatIntfCircuit 1.3.6.1.4.1.18.3.5.3.2.7.11.1.4 integer read-write
The circuit number of this interface.
           wfNatIntfDomain 1.3.6.1.4.1.18.3.5.3.2.7.11.1.5 displaystring read-write
This attribute specifies the Address Domain Name that this interface is connected to. Unidirectional NAT interfaces should be set with domain name of 'private' or 'public'
           wfNatIntfState 1.3.6.1.4.1.18.3.5.3.2.7.11.1.6 integer read-only
'The state of NAT on this interface' Enumeration: 'down': 2, 'init': 3, 'up': 1.
           wfNatIntfTxCount 1.3.6.1.4.1.18.3.5.3.2.7.11.1.7 counter read-only
Number of packets mapped over this interface from the local to the global network.'
           wfNatIntfRxCount 1.3.6.1.4.1.18.3.5.3.2.7.11.1.8 counter read-only
Number of packets mapped over this interface from the global to the local network.'
           wfNatIntfPktDropCount 1.3.6.1.4.1.18.3.5.3.2.7.11.1.9 counter read-only
Number of packets dropped on this interface
 wfNatSrcAddressFilterTable 1.3.6.1.4.1.18.3.5.3.2.7.12 no-access
Table of NAT source address filters.
       wfNatSrcAddressFilterEntry 1.3.6.1.4.1.18.3.5.3.2.7.12.1 no-access
Information describing each of the available source address filters.
           wfNatSrcAddressFilterDelete 1.3.6.1.4.1.18.3.5.3.2.7.12.1.1 integer read-write
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a source address filter entry. Enumeration: 'deleted': 2, 'created': 1.
           wfNatSrcAddressFilterDisable 1.3.6.1.4.1.18.3.5.3.2.7.12.1.2 integer read-write
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a source address filter entry. Enumeration: 'disabled': 2, 'enabled': 1.
           wfNatSrcAddressFilterAddress 1.3.6.1.4.1.18.3.5.3.2.7.12.1.3 ipaddress read-only
The IP beginning address of this source address filter entry.
           wfNatSrcAddressFilterPrefixLen 1.3.6.1.4.1.18.3.5.3.2.7.12.1.4 integer read-only
The number of contiguous bits set in the IP address mask which are used to define the address range of the entry.
           wfNatSrcAddressFilterIndex 1.3.6.1.4.1.18.3.5.3.2.7.12.1.5 integer read-only
A unique value for this entry in wfNatSrcAddressFilterTable.
           wfNatSrcAddressFilterNto1Addr 1.3.6.1.4.1.18.3.5.3.2.7.12.1.6 ipaddress read-write
specifies the N-to-1 translation address used for this source address filter, otherwise set to zero.
           wfNatSrcAddressFilterDomain 1.3.6.1.4.1.18.3.5.3.2.7.12.1.7 displaystring read-write
The value of this attribute specifies the Address Domain Name that this source address filter is valid for. For Unidirectional NAT this value must be 'public'
           wfNatSrcAddressFilterTransPoolSelector 1.3.6.1.4.1.18.3.5.3.2.7.12.1.8 integer read-write
The value of this attribute selects where to get the translation address for this source address filter from. This could be either the translation Pool defined for the inbound domain or the outbound domain for the packet in question. Enumeration: 'inbound': 1, 'outbound': 2.
           wfNatSrcAddressFilterStaticNextHop 1.3.6.1.4.1.18.3.5.3.2.7.12.1.9 ipaddress read-write
The IP address of the next hop of this source address filter entry.
           wfNatSrcAddressFilterUnnumCct 1.3.6.1.4.1.18.3.5.3.2.7.12.1.10 integer read-write
This Nat source address filter over the unnumbered interface.
 wfNatTranslationPoolTable 1.3.6.1.4.1.18.3.5.3.2.7.13 no-access
Table of address ranges.
       wfNatTranslationPoolEntry 1.3.6.1.4.1.18.3.5.3.2.7.13.1 no-access
Information describing each of the available translation pool.
           wfNatTranslationPoolDelete 1.3.6.1.4.1.18.3.5.3.2.7.13.1.1 integer read-write
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a translation pool entry. Enumeration: 'deleted': 2, 'created': 1.
           wfNatTranslationPoolDisable 1.3.6.1.4.1.18.3.5.3.2.7.13.1.2 integer read-write
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a translation pool entry. Enumeration: 'disabled': 2, 'enabled': 1.
           wfNatTranslationPoolAddress 1.3.6.1.4.1.18.3.5.3.2.7.13.1.3 ipaddress read-only
The IP beginning address of this translation pool entry.
           wfNatTranslationPoolPrefixLen 1.3.6.1.4.1.18.3.5.3.2.7.13.1.4 integer read-only
The number of contiguous bits set in the IP address mask which are used to define the address range of the entry.
           wfNatTranslationPoolIndex 1.3.6.1.4.1.18.3.5.3.2.7.13.1.5 integer read-only
A unique value for this entry in wfNatTranslationPoolTable.
           wfNatTranslationPoolDomain 1.3.6.1.4.1.18.3.5.3.2.7.13.1.6 displaystring read-write
The value of this attribute specifies the Address Domain Name that this translation pool is valid for. For Unidirectional NAT this value must be 'public'