VERILINK-ENTERPRISE-NCMIMUX-MIB: View SNMP OID List / Download MIB

VENDOR: VERILINK CORP


 Home MIB: VERILINK-ENTERPRISE-NCMIMUX-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 ncmimuxConfigTable 1.3.6.1.4.1.321.1.3030.7000 no-access
The IMUX Configuration table.
           ncmimuxConfigEntry 1.3.6.1.4.1.321.1.3030.7000.1 no-access
An entry in the ncm IMUX Configuration table.
               ncmimuxNIDConfigIndex 1.3.6.1.4.1.321.1.3030.7000.1.1 integer read-only
This variable indicates the node id value of the node.
               ncmimuxLineIndex 1.3.6.1.4.1.321.1.3030.7000.1.2 integer read-only
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
               ncmimuxEndId 1.3.6.1.4.1.321.1.3030.7000.1.3 integer read-only
This value for this object indicates which end of the equipment it is accessing. Enumeration: 'far-End': 2, 'near-End': 1.
               ncmimuxIfIndex 1.3.6.1.4.1.321.1.3030.7000.1.4 integer read-only
This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213).
               ncmimuxBkplaneBusSelect 1.3.6.1.4.1.321.1.3030.7000.1.5 integer read-write
This object only has signifiance for IMUX 2164. This variable specifies which IMUX line(s) is used, and which backplane bus is assigned to which line(s). The pattern of the the word is compsed as :- line# 8 7 6 5 4 3 2 1 bus # bus-B B D D B B D D(8) means lines 1,2,5,6 use bus - B lines 3,4,7,8 use bus - D The 'X' means no bus selection has been made. Enumeration: 'bus-AABBAABB': 2, 'bus-CCCCCCCC': 11, 'bus-AADDAADD': 4, 'bus-AAAAAAAA': 1, 'bus-DDAADDAA': 13, 'bus-CCAACCAA': 9, 'bus-DDDDDDDD': 16, 'bus-CCBBCCBB': 10, 'bus-AACCAACC': 3, 'bus-BBCCBBCC': 7, 'bus-BBAABBAA': 5, 'bus-EEXXEEXX': 18, 'bus-DDBBDDBB': 14, 'bus-CCDDCCDD': 12, 'bus-DDCCDDCC': 15, 'bus-BBDDBBDD': 8, 'bus-XXEEXXEE': 17, 'bus-BBBBBBBB': 6.
               ncmimuxCarrierLineRate 1.3.6.1.4.1.321.1.3030.7000.1.6 integer read-write
This variable specifies whether the carrier line rate is T1 or carrier line is E1. Enumeration: 'e1-rate': 2, 't1-rate': 1.
               ncmimuxCarrierLinesEqp 1.3.6.1.4.1.321.1.3030.7000.1.7 displaystring read-write
This variable indicates the inverse multiplexer carrier lines equipped. One bit per line. Here each bit in this byte represents one of the eight carrier lines that may be used by the Imux. Bit zero represents carrierline number one, and bit seven represents carrier line number eight. For each bit that is set to one, the corresponding carrier line will be configured for use by the ncmimux. For each bit that is set to zero, the corresponding carrier line will be excluded from the ncmimux configuration i.e., 1 = 0000 0001(bin). The range for this variable is from (in decimals 0 to 256).
               ncmimuxChanneling 1.3.6.1.4.1.321.1.3030.7000.1.8 integer read-write
This variable indicates the inverse multiplexer mode for T1 which by default is set to 64 Kbps and when the field is set to (1) the 56 kbps mode is selected. Enumeration: 'mode-56k': 2, 'mode-64k': 1.
               ncmimuxDTEClkTransmit 1.3.6.1.4.1.321.1.3030.7000.1.9 integer read-write
This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverted' refers to inverse multiplexer DTE clock phase is inverted. Enumeration: 'inverted': 2, 'normal': 1.
               ncmimuxDTEClkRecv 1.3.6.1.4.1.321.1.3030.7000.1.10 integer read-write
This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverted' refers to inverse multiplexer DTE clock phase is inverted. Enumeration: 'inverted': 2, 'normal': 1.
               ncmimuxDTEClkRefern 1.3.6.1.4.1.321.1.3030.7000.1.11 integer read-write
This field request to determine the DTE data port clock phase is normal or inverted. 'Normal' refers to inverse multiplexer DTE clock phase is normal. 'Inverted' refers to inverse multiplexer DTE clock phase is inverted. Enumeration: 'inverted': 2, 'normal': 1.
               ncmimuxDTEMode 1.3.6.1.4.1.321.1.3030.7000.1.12 integer read-write
This variable represents the DTE mode of the ncmimux Enumeration: 'manual': 2, 'automatic': 1.
               ncmimuxDSR 1.3.6.1.4.1.321.1.3030.7000.1.13 integer read-write
This variable represents Data Set Ready for the ncmimux which could be set for all interfaces. Enumeration: 'on': 2, 'off': 1.
               ncmimuxTM 1.3.6.1.4.1.321.1.3030.7000.1.14 integer read-write
This variable represents Test Mode for the ncmimux which could be set for all interfaces. Enumeration: 'on': 2, 'off': 1.
               ncmimuxCTS 1.3.6.1.4.1.321.1.3030.7000.1.15 integer read-write
This variable represents Clear To Send for the ncmimux which could be set for only V.35, EI530 and RS449 interfaces. Enumeration: 'on': 2, 'off': 1.
               ncmimuxDCD 1.3.6.1.4.1.321.1.3030.7000.1.16 integer read-write
This variable represents Data Carrier Detect for the ncmimux which could be set for only V.35, EI530 and RS449 interfaces. Enumeration: 'on': 2, 'off': 1.
               ncmimuxRI 1.3.6.1.4.1.321.1.3030.7000.1.17 integer read-write
This variable represents Ring Indicator for the ncmimux which could be set for only V.35 interfaces. Enumeration: 'on': 2, 'off': 1.
               ncmimuxSnapType 1.3.6.1.4.1.321.1.3030.7000.1.18 integer read-only
This variable represents the snap type for the ncmimux Enumeration: 'v35': 3, 'unknown': 1, 'eia530': 5, 'rs449': 6, 'eia530a': 4, 'hssi': 2.
               ncmimuxQuadSlot 1.3.6.1.4.1.321.1.3030.7000.1.19 integer read-write
This variable represents the DTE control mode of the ncmimux
 ncmimuxStatusTable 1.3.6.1.4.1.321.1.3030.7001 no-access
The IMUX Status table.
           ncmimuxStatusEntry 1.3.6.1.4.1.321.1.3030.7001.1 no-access
An entry in the IMUX Status table.
               ncmimuxNIDStatusIndex 1.3.6.1.4.1.321.1.3030.7001.1.1 integer read-only
This variable indicates the node id value of the node.
               ncmimuxStatusIndex 1.3.6.1.4.1.321.1.3030.7001.1.2 integer read-only
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
               ncmimuxStatEndId 1.3.6.1.4.1.321.1.3030.7001.1.3 integer read-only
This value for this object indicates which end of the equipment it is accessing. Enumeration: 'far-End': 2, 'near-End': 1.
               ncmimuxLinesEqp 1.3.6.1.4.1.321.1.3030.7001.1.4 displaystring read-only
This variable indicates the inverse multiplexer carrier lines equipped. One bit per line. Here each bit in this byte represents one of the eight carrier lines that may be used by the Imux. Bit zero represents carrierline number one, and bit seven represents carrier line number eight. For each bit that is set to one, the corresponding carrier line will be configured for use by the ncmimux. For each bit that is set to zero, the corresponding carrier line will be excluded from the ncmimux configuration i.e., 1 = 0000 0001(bin). The range for this variable is from (in decimals 0 to 256).
               ncmimuxLinesStat 1.3.6.1.4.1.321.1.3030.7001.1.5 displaystring read-only
This represents the lines active equivalent in tabs message, indicating when a carrier line has been allocated for use by the ncmimux. (Loop integrity must be established before the line can be put into active service).Options supported active, inactive or none.
               ncmimuxFrameStatus 1.3.6.1.4.1.321.1.3030.7001.1.6 displaystring read-only
This variable indicates the ncmimux frame structure is transmitted over each carrier line that has been allocated for use by the ncmimux. This field indicates that this frame structure has been recongnized and validated in the signal received on the carrier line or invalidated.
               ncmimuxCTSStatus 1.3.6.1.4.1.321.1.3030.7001.1.7 displaystring read-only
This variable indicates Clear To Send status that is encoded into the ncmimux frame structure on each carrier line to indicate that the integrity of the incoming signal has been validated. 'validCTS' refers to Clear To Send indication has been detected in the receive signal on the corresponding carrier line. 'invalidCTS' refers to Clear To send has not been detected. 'none' represents to not supported
               ncmimuxCRCStatus 1.3.6.1.4.1.321.1.3030.7001.1.8 displaystring read-only
This variable represents the crc error of the incoming frame structure corresponding to a Carrier Line.
               ncmimuxFarEndCRCStatus 1.3.6.1.4.1.321.1.3030.7001.1.9 displaystring read-only
This variable represents the crc error of the incoming frame structure received at the far end of the corresponding Carrier Lines.
               ncmimuxDataValidStatus 1.3.6.1.4.1.321.1.3030.7001.1.10 integer read-only
This variable represents the data valid of the Carrier Lines.
               ncmimuxNetworkAlarm 1.3.6.1.4.1.321.1.3030.7001.1.11 integer read-only
The value for this object indicates the front panel LED alarm status for the network interface. Enumeration: 'off': 1, 'flashing-Red-Green': 8, 'flashing-Red': 5, 'flashing-Green': 6, 'flashing-Yellow': 7, 'green': 3, 'yellow': 4, 'flashing-Green-Yellow': 9, 'red': 2, 'flashing-Yellow-Red': 10.
               ncmimuxAlarmLED 1.3.6.1.4.1.321.1.3030.7001.1.12 integer read-only
The value for this object indicates the front panel LED alarm status for the IMux. Enumeration: 'off': 1, 'flashing-Red-Green': 8, 'flashing-Red': 5, 'flashing-Green': 6, 'flashing-Yellow': 7, 'green': 3, 'yellow': 4, 'flashing-Green-Yellow': 9, 'red': 2, 'flashing-Yellow-Red': 10.
               ncmimuxEventMessages 1.3.6.1.4.1.321.1.3030.7001.1.13 integer read-only
The value for this object indicates the number of event messages in the event queue. The event queue is a list of state changes which are time-stamped and recorded.
 ncmimuxControlTable 1.3.6.1.4.1.321.1.3030.7002 no-access
The IMUX Control table.
           ncmimuxControlEntry 1.3.6.1.4.1.321.1.3030.7002.1 no-access
An entry in the IMUX Control table.
               ncmimuxNIDControlIndex 1.3.6.1.4.1.321.1.3030.7002.1.1 integer read-only
This variable indicates the node id value of the node.
               ncmimuxControlIndex 1.3.6.1.4.1.321.1.3030.7002.1.2 integer read-only
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
               ncmimuxCntEndId 1.3.6.1.4.1.321.1.3030.7002.1.3 integer read-only
This value for this object indicates which end of the equipment it is accessing. Enumeration: 'far-End': 2, 'near-End': 1.
               ncmimuxLoopback 1.3.6.1.4.1.321.1.3030.7002.1.4 integer read-write
This variable represents the Loopback status of Imux, ELB or PLB i.e., Equipment Loop back or Payload loop back. Enumeration: 'deactv-ELB': 5, 'actv-ELB': 2, 'actv-ELB-AND-PLB': 4, 'no-ELB-AND-PLB': 1, 'actv-PLB': 3, 'deactv-PLB': 6.
               ncmimuxAISPattern 1.3.6.1.4.1.321.1.3030.7002.1.5 integer read-write
This refers to the AIS test pattern initiated Enumeration: 'all-Ones': 2, 'all-Zeros': 3, 'disable': 1.
               ncmimuxTestPattern 1.3.6.1.4.1.321.1.3030.7002.1.6 integer read-only
This refers to the test pattern initiated Enumeration: 'disable': 1, 'pat-127': 2, 'inv-Pat-127': 3.
 ncmimuxDTEStatTable 1.3.6.1.4.1.321.1.3030.7003 no-access
The IMUX DTE Status table.
           ncmimuxDTEStatEntry 1.3.6.1.4.1.321.1.3030.7003.1 no-access
An entry in the IMUX DTEStatus table.
               ncmimuxNIDDTEStatIndex 1.3.6.1.4.1.321.1.3030.7003.1.1 integer read-only
This variable indicates the node id value of the node.
               ncmimuxDTEStatIndex 1.3.6.1.4.1.321.1.3030.7003.1.2 integer read-only
This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with this it should have the same value as ifIndex. Otherwise, the value exceeds ifNumber, and is a unique identifier following this rule: inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.
               ncmimuxDTEStatReg 1.3.6.1.4.1.321.1.3030.7003.1.3 integer read-only
This object reports the contents of the DTE Status Register as read from the IMUX hardware. Enumeration: 'hSSI-DTR': 1, 'v54-LL': 6, 'v54-RL': 5, 'hSSI-Loopback-B': 3, 'hSSI-Loopback-A': 2, 'v35-RTS': 4.
               ncmimuxDTEStatLPBK 1.3.6.1.4.1.321.1.3030.7003.1.4 integer read-only
This object reports the DTE Pattern and Loopback Code Register Status. (0) indicates that a Loop Up Code was detected. (1) indicates that Data Pattern or Loop Up Code errors were detected. (2) indicates a Loop Down Code was detected. (3) indicates Loop Down Code Errors were detected. (4) indicates PRBS 2 x 10^25 Aggregate Data Bandwidth. Enumeration: 'v54-LoopDown': 3, 'v35-LoopDown-Errors': 4, 'pRBS': 5, 'v54-LoopUp': 1, 'v54-Ptrn-Loop-Errors': 2.
               ncmimuxDTEStatAlarm 1.3.6.1.4.1.321.1.3030.7003.1.5 integer read-only
This object reports the front panel alarm LED status for the DTE interface. Enumeration: 'off': 1, 'flashing-Red-Green': 8, 'flashing-Red': 5, 'flashing-Green': 6, 'flashing-Yellow': 7, 'green': 3, 'yellow': 4, 'flashing-Green-Yellow': 9, 'red': 2, 'flashing-Yellow-Red': 10.