Telematics-Nevada-MIB: View SNMP OID List / Download MIB

total number of buffers in system - these buffers are freed at startup time to be allocated as needed. Statistic is zeroed at startup time.

minimum number of buffers available in last 15 minute cycle Statistic is zeroed at startup time.

cpu availablity -minimum percentage of CPU available in last 15 minute cycle. Statistic is zeroed at startup time.

current time number of minutes into current time - is set to 0 at start of current cycle - is incremented every minute - when incremented to 15 then cycle is over and curminbuf and curmincpu are calculated and curtime is set back to 0 Statistic is zeroed at startup time.

number of available buffers at last check - check is done every 3 seconds Statistic is zeroed at startup time.

percentage of CPU available at last check - check is done every 3 seconds Statistic is zeroed at startup time.

maximum CPU availablity maximum count of idle CPU cycles per 16 milliseconds - percentages of CPU availability are calculated relative to this number (freecpu,curmincpu,mincpu) Statistic is zeroed at startup time.

minimum number of buffers minimum number of available buffers ever recorded Statistic is zeroed at startup time.

cpu availablity minimum percentage of CPU available ever recorded Statistic is zeroed at startup time.

average rx packets per second average packets per second received during last 15 minute cycle Statistic is zeroed at startup time.

current rx packets per second packets per second received during last 3 second cycle Statistic is zeroed at startup time

average tx packets per second average packets per second transmitted during last 15 minute cycle Statistic is zeroed at startup time.

current tx packets per second packets per second transmitted during last 3 second cycle Statistic is zeroed at startup time.

Actual number of lcns allocated.

Change Request ID Confirmation management change request ID.

Indicates the current clock source.

Number of times clock failure has been detected.

date & time statistics last reset

Number of succesful modem calls received by ITI.

total number of records allowed in database file.

number of records in use.

nodeconf file.

nodeconf record.

Index of nodeconf record

Part Number -partnum- This is the part number of the software Format: AAAAAA-BBB-C-DDEEFF AAAAAA = Concatenated product code ie. a 4 link,8 channel switching PAD which has the code 2604-8 becomes 260408 BBB = Customer/feature code C = Medium DD = Major version number. A new set of documentation is generated for each major version EE = Database version number FF = Software version number Parameter is set during factory configuration.

Database Version (dbversion) Major and minor database release numbers Eg 0300 Similar usage as for software revision number Parameter is set during factory configuration.

Software Creation Date (swdate) Parameter is set during factory configuration.

Software Version (swversion) Major and minor software release numbers Eg. 0601 Parameter is set during factory configuration.

Max Custom Alarm Records (calarms) This field indicates the total num of custom alarm entries per box. DO NOT USE HUB-RESERVE3 OR TAKE ANY SPACE AWAY FROM IT TO USE FOR A NEW FIELD. IT IS THE SECRET HIDING PLACE WHERE THE HARDWARE CONFIGURATION IS STORED FOR USE IN DETECTING HARDWARE CHANGES WHEN REBOOTING. Default value is 0.

SD Script to automatically start after aprox. 10 seconds system boot

INF or SmartView Type (swtype) sview for old std billing Default value is sview (0+1). Enumeration: 'sview': 1, 'inf': 2, 'inf2': 3.

X.25 Call (nvX25call) This field indicates the total num of lcn per box Default value is 257.

Max Accounting Records (acctrec) This indicates the maximum number of accounting records that will be held in memory. When this number is reached, additional records will be discarded. Default value is 100.

Max Alarm Records (alarmrec) This indicates the maximum number of alarm records buffered Default value is 50.

used to busy out ITI ports when X25 links go down

Rate For Time Zone 1 (rate1)

Rate For Time Zone 2 (rate2)

Rate For Time Zone 3 (rate3)

Rate For Time Zone 4 (rate4)

Node Identifier (nodeid) This field is used by the Network Bus component to identify this node within a private network,and must be unique within that domain. Default value is 1000.

enhanced x25 stat (exstat) Enumeration: 'x25': 3, 'disable': 1, 'link': 2.

Restart timer for OMS Default value is 0.

Change Request Id

Primary clock source to synchronize TDM connects.

Primary clock source to synchronize TDM connects.

Primary clock source to synchronize TDM connects.

dspr failure threshold

frmr failure threshold

Qdli failure threshold

total number of records in file.

number of records in use.

acctstat file.

acctstat record, indexed by record number

name of component This is the name of component accumulating the statistics.

record ID This is the internal number of the accounting record.

Called address (from bcd)

Calling address (from bcd).

call origin: 1=iti/lserv 2=x25 . Enumeration: 'x25': 2, 'iti': 1.

segment size This is the segment size of this port that generates accounting. Statistic is zeroed at startup time.

date of call establishment (internal) Statistic is zeroed at startup time.

time of call establishment Statistic is zeroed at startup time.

time of call establishment Statistic is zeroed at startup time.

number transmitted packets Statistic is zeroed at startup time.

1000 transmitted packets Statistic is zeroed at startup time.

number received packets Statistic is zeroed at startup time.

1000 received packets Statistic is zeroed at startup time.

number transmitted characters Statistic is zeroed at startup time.

1000 transmitted characters Statistic is zeroed at startup time.

number received characters Statistic is zeroed at startup time.

1000 received characters Statistic is zeroed at startup time.

number transmitted segments Statistic is zeroed at startup time.

1000 transmitted segments Statistic is zeroed at startup time.

number received segments Statistic is zeroed at startup time.

1000 received segments Statistic is zeroed at startup time.

starting absolute time Statistic is zeroed at startup time.

date & time statistics last reset

Ptr to internal structure that starts accounting

Information function ptr provided by accounting entity

total number of records allowed in database file.

number of records in use.

acctoper file.

acctoper record.

Index of acctoper record

service component This is the name of the component that uses the accounting service. An example of this is NET1,ITI,etc. Parameter is set during factory configuration.

enable/disable This field is used to enable the accounting function. Default value is true (1+1). Enumeration: 'true': 2, 'false': 1.

segment size This field defines the size of a segment. A segment is usually a portion of a packet (ie. 64 bytes) as is more representative in actual accounting of resource utilization. The possible values range from one to the largest possible packet size. Default value is 64.

total number of records allowed in database file.

number of records in use.

modemstat file.

modemstat record.

Index of Modemstat record

digital modem status name.

Current state Enumeration: 'clearDown': 7, 'ecdc': 3, 'hshake': 2, 'idle': 1, 'retraining': 5, 'connected': 4, 'renegotiating': 6.

modem rate in bps. Enumeration: 'v33600': 21, 'v50000': 31, 'vv52000': 55, 'v1200': 6, 'v48000': 30, 'v9600NT': 10, 'v33333': 41, 'v32000': 22, 'vv36000': 43, 'vv40000': 46, 'v29333': 38, 'vv32000': 40, 'v52000': 32, 'v41333': 47, 'v40000': 26, 'v44000': 28, 'v28800': 19, 'v38667': 45, 'v46000': 29, 'v58667': 60, 'v26400': 18, 'vv56000': 58, 'v31200': 20, 'vv44000': 49, 'v53333': 56, 'v49333': 53, 'v9600': 11, 'v21600': 16, 'v54000': 33, 'v2400': 7, 'v19200': 15, 'v42000': 27, 'v57333': 59, 'v42667': 48, 'v600': 5, 'v36000': 24, 'v60000': 36, 'v50667': 54, 'v56000': 34, 'v58000': 35, 'v16800': 14, 'v54667': 57, 'v37333': 44, 'v30667': 39, 'v45333': 50, 'vv28000': 37, 'v46667': 51, 'vv60000': 61, 'v34000': 23, 'v34667': 42, 'v14400': 13, 'v4800': 8, 'v7200': 9, 'idle': 1, 't75R1200': 3, 't1200R75': 2, 'vv48000': 52, 'v24000': 17, 'v38000': 25, 'v300': 4, 'v12000': 12.

modem modulation scheme. Enumeration: 'v23': 12, 'v22': 6, 'v32': 4, 'v33': 15, 'v34': 2, 'unknown': 10, 'v29': 14, 'v32bis': 3, 'v110': 21, 'v21': 7, 'v17': 16, 'v34bis': 17, 'idle': 1, 'bell212': 9, 'vpcm': 18, 'v27': 13, 'v22bis': 5, 'bell103': 11.

modem error correction status Enumeration: 'mnpErrorCorrection': 3, 'idle': 1, 'v42ErrorCorrection': 2.

modem data compression status. Enumeration: 'on': 2, 'idle': 1, 'off': 3.

synchronous or asynchronous. Enumeration: 'async': 4, 'predetection': 2, 'sync': 3.

receive parity setting. Enumeration: 'even': 2, 'none': 6, 'space': 5, 'clear': 7, 'mark': 4, 'odd': 3.

transmit parity setting. Enumeration: 'even': 2, 'none': 6, 'space': 5, 'clear': 7, 'mark': 4, 'odd': 3.

for async to sync PPP, shows asy char control maps.

modem noise level (mean squared err).

Modem receive level.

Number retrains this call.

Number renegotiations this call.

soft init selftest result. Enumeration: 'sramFailed': 4, 'sramAndDspFailed': 5, 'passed': 2, 'dspFailed': 3.

Firmware version number

DSP microcode product code.

Modem clear rx parity (rxpclear) bit. Enumeration: 'yes': 2, 'no': 3.

the name of the DSP allocated.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

modemconf file.

modemconf record.

Index of modemconf record

Digital modem resource config name (name) Parameter is set during factory configuration.

Digital modemprof name that it is associated with

Enabled or not. Enumeration: 'yes': 2, 'no': 3.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

symuser file.

symuser record.

Index of symuser record

User Name (username) Name of user allowed to use system management functions. The System Manager Interface attempts to match the call user data field of an incoming call against the entries in this file. If no match is found, the call is cleared.

User Password (password) User password. After a user name is matched,the user is asked to enter their assigned password. If it is not entered correctly,the call is cleared.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

nmsuser file.

nmsuser record.

Index of nmsuser record

NMS X.121 Address (calladdr)

NMS Userdata (calldata) Default value is 0.

NMS Component Password (password) Default value is 0.

Packet Size (psiz) Default value is 7+1. Enumeration: 'b64': 7, 'b256': 9, 'b512': 10, 'b16': 5, 'b32': 6, 'b1024': 11, 'b128': 8.

Window Size (wsiz) Default value is 2.

RPOA Code (rpoacode) Default value is 0.

Outgoing Charging Restriction (ochrg) Default value is 1+1. Enumeration: 'oall': 2, 'onorm': 3, 'orev': 4.

Closed User Group Id (cug) Default value is 0.

Throughput Class (tput) Default value is 10+1. Enumeration: 'bps300': 6, 'bps2400': 9, 'bps600': 7, 'bps150': 5, 'bps4800': 10, 'bps1200': 8, 'bps9600': 11, 'bps75': 4.

NMS Identification (nmsid)

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

netmap file.

netmap record.

Index of netmap record

Network X.121 Address (netaddr) This field contains the network address pattern that is matched against the the network address field in a 'call request'.

User Data (userdata) This field contains the call user data pattern that is matched against the call user data field in a 'call request'.

Node Identifier (nodeid) This parameter is the identifier of the entity providing the service for a matched network address and user data.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

netroute file.

netroute record.

Index of netroute record

Node Identifier (nodeid) This parameter is an identifier of destination node. This value was located in NETMAP.

Service Component (service) This parameter is an index into component table of component providing the service.

Route Priority (prio) This parameter represents the user-assigned priority of the route. The router searches this file for the highest priority route that will allow more connections. If the highest priority route is unavailable,the next highest is tried until all possibilities are exhausted and the call is cleared. Default value is 100.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

netpvc file.

netpvc record.

Index of netpvc record

Service Component (service) COMPID and PVCID together uniquely identify one end of a PVC,and make up the key to this file when searching for an 'A' end.

Local PVC Identifier (pvcid)

Global PVC Identifier (pvccode) PVCCODE uniquely identifies a PVC,and is used as the key to this file when searching for a 'B' end.

PVC End (pvcend) Default value is 2+1. Enumeration: 'symmetricEnd': 4, 'terminatingEnd': 3, 'originatingEnd': 2.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

netpvcmap file.

netpvcmap record.

Index of netpvcmap record

Global PVC Identifier (pvccode)

Node Identifier (nodeid) This parameter is the identifier of the entity providing 'B' end of a PVC within our network.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

netcon file.

netcon record, indexed by record number

Index of netcon record

source component id Originating component of the connection.

destination component id Receiving component of the connection.

calling network address (from bcd) The calling network address.

called network address (from bcd) The called network address.

connection state The actual state of this connection. Initial status is 1. Enumeration: 'initial': 2, 'awaitingResponse': 3, 'dataTransfer': 5, 'disconnected': 9.

Internal Network connection identifier.

Internal Source identifier.

Internal Destination identifier.

total number of records allowed in database file.

number of records in use.

routemap file.

routemap record.

Index of routemap record

Address string to be translated (addrstr).

How to interpret addrstr (addrtype). Enumeration: 'calledsub': 3, 'callednum': 2, 'any': 9.

Netaddr yielded by match with addrstr.

Userdata yielded by match with addrstr.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Mediastat file.

Mediastat record.

Index of mediastat record

original boot image. Enumeration: 'image2': 401, 'image1': 1.

current boot image. Enumeration: 'image2': 401, 'image1': 1.

debug flag. Enumeration: 'enable': 2, 'disable': 1.

auto image change. Enumeration: 'enable': 2, 'disable': 1.

dump flag. Enumeration: 'enable': 2, 'disable': 1.

side0 database version.

side0 software version.

side1 database version.

side1 software version.

storage medium size. Enumeration: 'v20MB': 21, 'absent': 1, 'v12MB': 13, 'v10MB': 11, 'v16MB': 17, 'v4MB': 5, 'v18MB': 19, 'v8MB': 9, 'v2MB': 3, 'v6MB': 7, 'v32MB': 33, 'v14MB': 15.

total number of records allowed in database file.

number of records in use.

Backhaul instance table definition.

A tunnel table entry containing objects which configure a tunnel protocol.

Backhaul configuration entry index number.

Port name (portname)

Resource pool name.

Backhaul line protocol. Enumeration: 'rfc1662': 3, 'dontcare': 2.

Backhaul line protocol. Enumeration: 'transparent': 2, 'rfc1598': 3.

Backhaul routing protocol. Enumeration: 'usecalledsb': 4, 'useconfig': 2, 'usecallednm': 3.

Backhaul network address when rtmethod is useconfig.

Backhaul configuration user data.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Backhaul instance status table definition.

A tunnel status table entry containing fields which store tunnel status information.

Backhaul status entry index number.

Port on which this Backhaul status entry is applied.

Resource pool on which this Backhaul status entry is applied.

Current connection status. Enumeration: 'tunnelactive': 6, 'tunnelnoport': 3, 'tunnelinactive': 4, 'tunnelcalling': 5, 'tunnelnocb': 2.

String upon which routing was based.

Network address to which call was routed.

User data to which call was routed.

No of attempts to place current call.

No of failed attempts to place current call.

No of frames switched from line to tunnel route.

No of frames switched from tunnel route to line.

date & time statistics last reset

DLI configuration table definition.The actual database contains 17 tables, if a DLI card is plugged in one of the slot then the data table matched the slot will become active, otherwise the record is not active. This table combines 17 tables into one MIB table which uses two table instances: slot and port.

DLI configuration record.

CDLI slot index number.

CDLI card port index number.

The name of the DLI card port such as CDLI1_I2.

Frame format. Enumeration: 'pcm30': 3, 'd4sf': 1, 'crc4': 4, 'd4esf': 2.

Code format. Enumeration: 'ami': 1, 'hdb3': 3, 'b8zs': 2.

Facilities data link format. Enumeration: 'ansi': 3, 'none': 1, 'att': 2.

Signal type. Enumeration: 'rbs': 2, 'ccs': 1.

Line impedance. Enumeration: 'ohm-120': 1, 'ohm-100': 3, 'ohm-75': 2.

Port enable. Enumeration: 'yes': 1, 'no': 2.

csudsu enabled or not. Enumeration: 'yes': 1, 'no': 2.

Attenuation of the line . Enumeration: 't1neg150': 8, 't130': 1, 't1neg225': 9, 't1neg75': 7, 't124': 2, 't16': 5, 't10': 6, 't112': 4, 't118': 3.

Gain of the receiver. Enumeration: 'g26db': 2, 'g43db': 4, 'g12db': 1, 'g36db': 3.

Data inversion enabled or not. Enumeration: 'yes': 1, 'no': 2.

DLI statistics table definition.The actual database contains 17 tables, if a DLI card is plugged in one of the slot then the data table matched the slot will become active, otherwise the record is not active. This table combines 17 tables into one MIB table which uses two table instances: slot and port.

DLI statistics record.

SDLI slot index number.

SDLI card port index number.

SDLI entry name such as SDLI1_I2.

SDLI card port type such as E1 or T1.

SDLI card port current device state. Enumeration: 'blue': 5, 'mLine': 7, 'ok': 1, 'unknwn': 2, 'busyAIS': 9, 'down': 3, 'mPay': 8, 'yell': 6, 'red': 4.

SDLI card port red alarm count.

SDLI card port yellow alarm count.

SDLI card port blue alarm count.

SDLI card port crc alarm count.

TX underrun count.

RX Slip count.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

Device usage group configuration table.

Device usage group configuration record.

Usage group entry index number.

Usage group entry name.

Usage group entry resource pool name.

Number of devices reserved for this entry.

Allocation of disallowance thrreshold for this entry.

Maximum bandwidth allocated to this entry.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Device usage group statistics table.

Device usage group statistics record.

Usage group statistics entry index number.

Usage group statistics entry name.

Usage group statistics entry resource pool name.

Number of devices allocated to this group.

Amount of bandwidth allocated to this group.

Rejections to this group due to bandwidth restrain.

Rejections to this group due to device unavailability.

Rejections to this group due to threshold restriction.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

Device pool registry statistics.

Device pool registry statistics record.

Device pool registry statistics entry index number.

Device pool registry statistics entry name.

Device class of this pool. Enumeration: 'port': 1, 'dsp': 2.

Number of devices registered to this pool.

Number of devices reserved to this pool.

Number of devices available for allocation.

Number of devices presently allocated for use.

Maximum number of numused since last box reset.

date & time statistics last reset

Framer card configuration table definition. The actual framer card database has 17 tables. Each table uses name convention: CFRMR plus slot number. Each framer card has two static WAN ports and 128 smart ports. This table will combine 17 databases into one table. In order to support the actual framer card configuration, this table requires two instances: slot and port number.

Framer card configuration record definition. The total record number is 17. If there is a framer card plugged in one of the slot, then the corresponding framer record is active. Otherwise the record is not active.

Framer card slot number.

For static port, the index number is from 1 to 2. For smart port type, the index number is from 3 to 130.

The name of a framer card port.

Framer card port baud rate. Enumeration: 'v448K': 8, 'v512K': 9, 'v704K': 12, 'v960K': 16, 'v1472K': 24, 'v1344K': 22, 'v1536K': 25, 'v64K': 2, 'v1984K': 32, 'v1728K': 28, 'v1216K': 20, 'v1664K': 27, 'undef': 1, 'v256K': 5, 'v768K': 13, 'v1856K': 30, 'v1600K': 26, 'v1920K': 31, 'v832K': 14, 'v128K': 3, 'v1152K': 19, 'v320K': 6, 'v192K': 4, 'v1024K': 17, 'v2048K': 33, 'v1792K': 29, 'v576K': 10, 'v384K': 7, 'v640K': 11, 'v896K': 15, 'v1408K': 23, 'v1280K': 21, 'v1088K': 18.

Port interface type. Enumeration: 'v3wire': 1, 'vx21bis': 2.

Port clock mode. Enumeration: 'exsync': 2, 'insync': 1.

WAN port eia debounce interval.

Enable or disable port. Enumeration: 'yes': 2, 'no': 1.

Framer card statistics table definition. The actual framer card database has 17 tables. Each table uses name convention: SFRMR plus slot number. Each framer card has two static WAN ports and 128 smart ports. This table will combine 17 databases into one table. In order to support the actual framer card configuration, this table requires two instances: slot and port number.

Framer card statistics record definition. The total record number is 17. If there is a framer card plugged in one of the slot, then the corresponding framer record is active. Otherwise the record is not active.

Framer card slot number.

For static port, the index number is from 1 to 2. For smart port type, the index number is from 3 to 130.

The name of a framer card port.

The operation mode. Enumeration: 'absent': 1, 'async': 4, 'sync': 5, 'dead': 2, 'broken': 3.

The operation state. Enumeration: 'down': 2, 'test': 5, 'setup': 3, 'up': 4, 'free': 1.

Framer card port baud rate. Enumeration: 'v448K': 8, 'v512K': 9, 'v704K': 12, 'v960K': 16, 'v1472K': 24, 'v1344K': 22, 'v1536K': 25, 'v64K': 2, 'v1984K': 32, 'v1728K': 28, 'v1216K': 20, 'v1664K': 27, 'undef': 1, 'v256K': 5, 'v768K': 13, 'v1856K': 30, 'v1600K': 26, 'v1920K': 31, 'v832K': 14, 'v128K': 3, 'v1152K': 19, 'v320K': 6, 'v192K': 4, 'v1024K': 17, 'v2048K': 33, 'v1792K': 29, 'v576K': 10, 'v384K': 7, 'v640K': 11, 'v896K': 15, 'v1408K': 23, 'v1280K': 21, 'v1088K': 18.

Circuit ID of Munich ports.

RXOFF

TXOFF

RNRXOFF

RNTXOFF

Number of lost frames.

FERRS

PERRS

Number of receive overruns frames.

Number of CRC errors.

Number of receive aborte frames.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

Slot statistics table definition.

Nevada product is a 17 slot chassis. Each slot can be plugged in a communication card module. The module can be a Host Packet, Framer or DLI card module. The system can have only one Host Module and up to two Framer card module. This table contains statistics information for each slot.

Slot index number.

Slot name.

Slot card type. Enumeration: 'v24V35': 61, 'v35': 60, 'qDE1IO': 63, 'oDLI': 11, 'framer': 4, 'ps': 13, 'qDT1IO': 64, 'pEM': 66, 'framer2': 8, 'fRMRIO': 53, 'dsp': 5, 'pOWERIO': 57, 'qDE1': 9, 'dliT1': 3, 'oDIO': 65, 'empty': 1, 'v11EXT': 58, 'v24': 62, 'phost': 6, 'qDT1': 10, 't1IO': 56, 'dliE1': 2, 'fRMR': 12, 'pHOSTIO': 52, 'none': 51, 'v11INT': 59, 'pHIOM': 67, 'qpsPower': 7, 'e1IO': 55.

Slot IO type. Enumeration: 't1Io': 56, 'none': 51, 'v24v35': 61, 'v11int': 59, 'v24': 62, 'powerIo': 57, 'frmrIo': 53, 'pHIOM': 67, 'qDT1IO': 64, 'pEM': 66, 'e1Io': 54, 'qDE1IO': 63, 'v35': 60, 'phostIo': 52, 'oDIO': 65, 'empty': 1, 'v11ext': 58.

Slot IO type. Enumeration: 'p5-100': 2, 'adsp2181': 4, 'i960JF': 3, 'notapp': 1.

Amount of RAM on card.

Status of card as given by bats. good(1), -- Card is working failure(2), -- Card is failing notPowered(3), -- Power Supply -48 volts not supplied notapplicable(4) -- not applicable Enumeration: 'failure': 2, 'good': 1, 'notPowered': 3, 'notapplicable': 4.

Card id from eeprom.

Hardware Revision of the board.

Catalog part number.

Serial Number.

Production Check Date.

DSP configuration table definition.The actual database contains 17 tables, if a DSP card is plugged in one of the slot then the data table matched the slot will become active, otherwise the record is not active. This table combines 17 tables into one MIB table which uses two table instances: slot and port.

DLI configuration record.

CDSP slot number.

CDSP port number.

CDSP port name.

CDSP port enable control. Enumeration: 'slowno': 3, 'fastno': 4, 'yes': 2.

CDSP num of consecutive hand shakes failed.

CDSP num of times redownload failed.

DSP statistics table definition.The actual database contains 17 tables, if a DSP card is plugged in one of the slot then the data table matched the slot will become active, otherwise the record is not active. This table combines 17 tables into one MIB table which uses two table instances: slot and port.

DLI configuration record.

SDSP slot number.

SDSP port number.

SDSP port name.

CDSP port state. Enumeration: 'idle': 2, 'busy': 3, 'asleep': 5, 'dead': 4, 'dwld': 6.

number of consecutive handshake failures.

number of redownload attempts failed.

SDSP port state. Enumeration: 'cmdTimeout': 10, 'llHandTimeout': 8, 'monRegTimeout': 11, 'notUsable': 18, 'handshkeAbort': 5, 'healthy': 2, 'llHandHsAbo': 9, 'handModify': 16, 'portUpFail': 4, 'handshkeTimeout': 6, 'chCreErrNoReload': 13, 'dwldFail': 3, 'clrDownTimeout': 12, 'chCreErrReload': 14, 'userReset': 17, 'llHandAbort': 7, 'userDown': 15.

Number of calls processed on this DSP.

Number of calls faild prior to negotiation start.

date & time statistics last reset

Total number of INcoming calls made to this DSP.

Total number of OUTgoing calls made to this DSP.

Total number of failed negotiations INcoming.

Total number of failed negotiations OUTgoing.

DMOD- primary modem hs ended in abort condition.

DMOD- primary modem hs ended in timeout condition.

DMOD- Link layer modem hs ended in abort condition.

DMOD- Link layer modem hs ende in timeout condition.

DMOD- Link layer modem hs ended in primary hs aborted condition.

DMOD- Command Response Timeout error.

DMOD- Cleardown procedure ended in timeout condition.

DMOD- Moniter Register timeout error.

DMOD- Port Up failure No SABM from DSP to start the session.

DMOD- CHCRERR - with DSP Fail logic optioned.

DMOD- CHCRERR - with DSP Fail logic not optioned.

DMOD- modify action in SDSPx caused numfaicon threshold to be reached.

total number of records allowed in database file.

number of records in use.

Circuit routing table.

Circuit routing table record.

Index of croute record.

Address.

routing new var. Enumeration: 'callngsub': 5, 'calledsub': 4, 'noroute': 1, 'callednum': 2, 'callngnum': 3.

circuit type. Enumeration: 'pernament': 3, 'switched': 2.

Protocol Specified. Enumeration: 'g711m': 4, 'v110': 6, 'g711': 5, 'dcprot': 2, 'noprot': 1, 'v120': 7, 'g711a': 3.

Data mode. Enumeration: 'dcmode': 2, 'async': 4, 'sync': 3, 'nomode': 1.

rcscp1.

rcscp1.

Record id of dialmap record to use.

OBSOLETE - removed field.

Direction record is for. Enumeration: 'outgoing': 2, 'incoming': 1, 'unspec': 3.

A priority value. Used to specify which record gets precedence if two records have the same addr. Enumeration: 'second': 2, 'fourth': 4, 'third': 3, 'first': 1.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Circuit connection status table.

crcstat record indexed by record number.

Index of crcstat record.

circuit connection identifier.

circuit connection state. Enumeration: 'hung': 5, 'connected': 3, 'connecting': 2, 'pending': 1, 'clearing': 4.

called party address.

bandwidth of permanent circuit.

resource info 0.

device info 0.

resource info 1.

device info 1.

resource info 2.

device info 2.

OBSOLETE - removed field.

OBSOLETE - removed field.

calling party address.

called party subaddress.

calling party subaddress.

L1prot. Enumeration: 'g711MU': 4, 'v110': 6, 'g711': 5, 'dcprot': 2, 'noprot': 1, 'v120': 7, 'g711A': 3.

Layer 1 data mode. Enumeration: 'dcmode': 2, 'async': 4, 'sync': 3, 'nomode': 1.

Croute record id used.

Routing method. Enumeration: 'callngsub': 5, 'calledsub': 4, 'noroute': 1, 'callednum': 2, 'callngnum': 3.

Direction call was in. Enumeration: 'outgoing': 2, 'incoming': 1, 'unspec': 3.

total number of records allowed in database file.

number of records in use.

Circuit failure status table.

crfstat record indexed by record number.

Index of crfstat record.

circuit connection identifier.

called party address.

calling party address.

called party subaddress.

calling party subaddress.

L1prot. Enumeration: 'g711MU': 4, 'v110': 6, 'g711': 5, 'dcprot': 2, 'noprot': 1, 'v120': 7, 'g711A': 3.

Layer 1 data mode. Enumeration: 'async': 4, 'dcprot': 2, 'sync': 3, 'nomode': 1.

Croute record id used.

Routing method. Enumeration: 'callngsub': 5, 'calledsub': 4, 'noroute': 1, 'callednum': 2, 'callngnum': 3.

address.

circuit connection failure cause. Enumeration: 'dvBwRej': 8, 'dspNoSetupI': 20, 'portNoConn': 12, 'noDialtone': 37, 'dvThrshRej': 9, 'dspHwUnavail': 18, 'dspMsgNotPS': 27, 'dspBadResrc': 19, 'busy': 34, 'dspChCrDwlF': 26, 'causeUnspecified': 38, 'psChCrErr': 15, 'dspChCrSyEr': 24, 'crfRsrcBusy': 31, 'dvNoPool': 16, 'frBwUnavail': 11, 'crfNoRoute': 2, 'dspRoRoNone': 21, 'crfConAbort': 5, 'tsUnavail': 36, 'scsaStuck': 13, 'dvUnavail': 10, 'r2NoDspTs': 28, 'dspChCrBitF': 25, 'dspmFullLts': 32, 'crfRcscAllocFail': 4, 'crfTsAllocFail': 3, 'dspChCRNoHw': 23, 'dvNoGroup': 7, 'srcAborted': 30, 'dspChCRspTO': 22, 'sigChCrErr': 33, 'noAnswer': 35, 'r2ChCrErr': 29, 'dvBadClass': 17, 'crfConFail': 6, 'psReject': 14.

resource info 0.

resource info 1.

resource info 2.

OBSOLETE - removed field.

Direction record is for. Enumeration: 'outgoing': 2, 'incoming': 1, 'unspec': 3.

total number of records allowed in database file.

number of records in use.

resouce registry (system registry) status table.

rrstat record indexed by record number.

Index of rrstat record.

resource pool name.

resource pool class. Enumeration: 'protocolStack': 2, 'digitalModem': 3, 'priCall': 4, 'priDc': 5.

number of resources.

number of connected resources.

Maximum number of connected resources.

Total number of incoming calls processed.

Total number of outgoing calls processed.

Total number of calls processed.

Average length of call in seconds.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

modemconf file.

modemconf record.

Index of modemconf record

Modem Prof resource config name (name)

Resource pool name.

Device usage group name.

Modem modulation scheme (type) Default value is 3. Enumeration: 'v32': 4, 'v34': 2, 'v21rev': 16, 'v110b9600': 27, 'v110b19200': 30, 'v32bis': 3, 'v110b4800': 25, 'v110b600': 22, 'v110b48000': 31, 'modauto': 1, 'v22bis': 7, 'v22': 8, 'v21': 9, 'v110b7200': 26, 'v110b14400': 29, 'v110b12000': 28, 'v34bis': 14, 'pautoc': 13, 'v110mod': 21, 'vpcm': 15, 'v23t75r12': 5, 'b212a': 10, 'v110b56000': 32, 'b103': 11, 'v110b2400': 24, 'v110b1200': 23, 'pautob': 12, 'v23t12r75': 6.

Modem error correction option. Enumeration: 'autoec': 5, 'v42ec': 2, 'mNPec': 3, 'disable': 1, 'eitherec': 4.

Modem data compression option. Enumeration: 'enable': 2, 'disable': 1.

Modem sync / async option. Enumeration: 'async': 4, 'sync': 3, 'auto': 8.

Modem companding type. Enumeration: 'alaw': 3, 'nocmpdt': 4, 'mulaw': 2.

Transmit level (txlvl) Default value is 13.

Modem receive threshold (rxthresh) Default value is 38.

Modem generate answer (anston) tone. Enumeration: 'yes': 2, 'no': 3.

Mode answer tone (anstondur) duration.

Modem wait to send answer (bildly) tone.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

modem autorel fallback char.

number of records in use.

modemconf file.

IfStackInfo record.

highre layer interface number.

Lower layer interface number.

Status of the entry.

Record ID to get info on this

total number of records allowed in database file.

number of records in use.

Dialmap table.

Dialmap table record.

Index of dialmap record.

Number of digits to delete.

Digits to add after digits deleted.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Dspmalloc table.

Dspmalloc table record.

Index of dspmalloc record

Type of DSP - kflex or V.90. Enumeration: 'kfModem': 2, 'v90Modem': 3.

Allocation proportion.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

Dialstat table.

Dialstat table record.

Index of Dialstat record

Resource Name.

Number of dial-out Sessions currently occuring.

Number of call attempts currently occuring.

Is trace enabled? Enumeration: 'yes': 2, 'busy': 4, 'no': 1.

Last Called Number.

Last ISDN cause code.

Last X.25 diagnostic.

Last Response.

Number of dial-out sessions.

Number of call attempts. (May be multiple attempts per dialout request).

Number of successful dial-out attempts.

Number of failed dial-out attempts.

Number of times circuit creation failed immediately.

Number of fails due to error in dialout string command.

Number of fails due to no dialtone.

Number of fails due to remote busy.

Number of fails due to routing error.

Number of Fails because no modem was available.

Number of fails because of no user input within time limit.

Number of fails because invalid user input received.

Number of fails due to no answer.

Number of failed modem negotiation.

Number of fails after ISDN connection for reasons other than modem negotiation failure.

Number of miscellaneous failures not counted elsewhere.

Maximum number concurrently calling.

Average time for dial-out for successful dial-out request, in units of tenths of a second.

Average time for dial-out for filaed cases, in units of tenths of a second.

number of aborted redials, JATE redial restriction.

Framer card statistics table definition. The actual framer card database has 17 tables. Each table uses name convention: frmrstat plus slot number. This table will combine 17 databases into one table. In order to support the actual framer card configuration, this table requires the slot number

Framer card statistics record definition. The total record number is 17. If there is a framer card plugged in one of the slot, then the corresponding framer record is active. Otherwise the record is not active.

Framer card slot number.

State of framer card. Enumeration: 'download': 6, 'up': 4, 'dead': 2, 'free': 1, 'dying': 3.

Reason for last failure. Enumeration: 'download': 6, 'none': 1, 'softfail': 2, 'hardfail': 3.

Date and Time of last framer card reset.

Number of download attempts.

Number of successful reloads.

number of smartport calls made.

number of calls currently up.

number of successful port ups.

number of failed port ups.

number of frames transmitted.

number of frames received.

Number of bytes transmitted.

number of bytes received.

Probable Cause The port placed or accepted call with the attached device. Probable Effect Nevada has a network connection Recommended Action Network connection is now available for data transfer.

Probable Cause The port disconnected with the attached device. Probable Effect Nevada does not have a network connection on the port. Recommended Action Refer stat files itipstat, iticstat, itiustat & portstat.

Probable Cause number of available ports at site Probable Effect can place calls Recommended Action place calls

Probable Cause All available ports are in use Probable Effect No additional users will be able to call in. Recommended Action Add more ports to the particular site.

Probable Cause Data mode timer expired Probable Effect Recommended Action

Probable Cause Both DUI Circuits down. Probable Effect Can not accept calls. Recommended Action

LSERVER: Database Up: primary NUA `S0`

LSERVER: Database Up: secondary NUA `S0`

Probable Cause X.25 detected that the link is down. Probable Effect Data transfer over the specified link not possible Recommended Action Correct the Physical connection and/or configuration

Probable Cause X.25 detected that the link has come up. Probable Effect Data transfer over the specified link possible Recommended Action New calls can now be established on this link

Nevada running alternate config on side `n0`

data base auto save

Nevada CRC error on database

save count is zero

Nevada local database has been changed

Nevada statistics rate increased to level 1

Nevada statistics rate increased to level 2

Nevada statistics rate decrease to below level 1

Nevada statistics rate decrease to below level 2

Nevada status value reached

Nevada status value no longer met

Probable Cause framer failed to do the required action Probable Effect Recommended Action

Probable Cause framer card in the indicated slot failed to do the requested action Probable Effect no traffic will flow Recommended Action check hardware and software configuration

Nevada Frame Relay Interface up ready

Nevada Frame Relay Interface down not-ready

Probable Cause The specified frame relay interface has detected LMI error. Probable Effect Stops PVC traffic. Recommended Action Wait for LMI to enter normal state to resume PVC traffic.

Probable Cause The specified frame relay interface has found LMI in normal state. Probable Effect Enables PVC traffic to resume. Recommended Action The FRI is available for data transfer.

Probable Cause All DLCIs on the FRI are functional. Probable Effect All FRPVCs enter data transfer state. Recommended Action All FRPVCs are available for data transfer.

Probable Cause One or more DLCIs on the FRI not functional. Probable Effect Data transfer will stop on the FRPVC that has gone down. Recommended Action Refer stat files fristat, frvcstat and frstat.

Probable Cause ELX has gone up. Probable Effect Data can be exchanged Recommended Action Pass data through

Probable Cause ELX has gone down. Probable Effect Data can not be exchanged Recommended Action Correct configuration, cable connection or the hardware setup.

Probable Cause The Link Control Protocol (LCP) has gone up. Probable Effect The link is configured, tested and available for higher-level protocols such as IPCP (Internet Protocol Control Protocol). Recommended Action The PPP link is now available for higher-level protocol such as IPCP.

Probable Cause The Link Control Protocol (LCP) has gone down. Probable Effect The link is not configured and is not available for higher-level protocols such as IPCP (Internet Protocol Control Protocol). Recommended Action Refer PPP statfile pppstat.

Probable Cause The IP Control Protocol (IPCP) has gone up. Probable Effect The Network Layer Protocol is selected and datagrams can be sent. Recommended Action The PPP link is now available for datagram traffic.

Probable Cause The IP Control Protocol (IPCP) has gone down. Probable Effect The Network Layer Protocol is not selected and datagrams can not be sent. Recommended Action Refer PPP statfile pppstat.

Probable Cause ISDN Data Layer Up PRI is functional on the DLI Probable Effect Data Channel responding. Recommended Action Unit is ready to receive ISDN calls

Probable Cause ISDN Data Layer Down PRI is Not functional on the DLI Probable Effect Data Channel not responding bchannel calls will fail Recommended Action Test the DLI and check associated Config in CDLI and PRICONF

Probable Cause The LCP protocol has entered the network phase on the PPP link Probable Effect Network layer protocols such as IPCP can now exchange packets on the link Recommended Action None

Probable Cause The LCP protocol is down on the network phase on the PPP link Probable Effect Network layer protocols such as IPCP can not exchange packets on the link Recommended Action

Probable Cause A PPP link has been added to a multilink bundle Probable Effect Greater bandwidth is available on the bundle Recommended Action None required. Informational only

Probable Cause A PPP link has been dropped from a multilink bundle Probable Effect The bandwidth for the bundle has been reduced. If this was the last link in the bundle the bundle will be closed Recommended Action None required, informational only

Probable Cause Number of ISDN calls failure have reached the configured threshold Probable Effect ISDN failure -- results in failed ISDN calls Recommended Action check the ISDN IO cards/service provider/hardware

Probable Cause Number of Modem failures has reached the configured threshold one Probable Effect Modem failure results in failed calls Recommended Action check modem hardware/configuration

Probable Cause Number of Modem failures has reached the configured threshold two Probable Effect Modem failure results in failed calls Recommended Action check modem hardware/configuration

Probable Cause Number of Modem failures has reached the configured threshold three Probable Effect Modem failure results in failed calls Recommended Action check modem hardware/configuration

Probable Cause DSPR has failed. Probable Effect DSPR card has failed -- hardware resources failure Recommended Action Replace the DSPR card

Probable Cause FRAMER card failure Probable Effect FRAMER card failure -- system failure Recommended Action replace the framer card

Probable Cause QDLI card has failed Probable Effect QDLI card has failed Recommended Action None required, informational only

Probable Cause a card has been deleted in the indicated slot Probable Effect a card has been deleted -- hotswap Recommended Action None required, informational only

Probable Cause a card has been inserted in the indicated slot Probable Effect a card has been inserted -- hotswap Recommended Action None required, informational only

Minutes into current 15-minute cycle Statistic is zeroed at startup time.

Current snapshot of Tx Frames/Second Statistic is zeroed at startup time.

Average Tx Frames/Second for 15-minute cycle Statistic is zeroed at startup time.

Current snapshot of Rx Frames/Second Statistic is zeroed at startup time.

Average Rx Frames/Second for 15-minute cycle Statistic is zeroed at startup time.

Current snapshot of mapped Tx Frames/Second Statistic is zeroed at startup time.

Average mapped Tx Frames/Second for 15-minute cycle Statistic is zeroed at startup time.

Current snapshot of mapped Rx Frames/Second Statistic is zeroed at startup time.

Average mapped Rx Frames/Second for 15-minute cycle Statistic is zeroed at startup time.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

fristat file.

fristat record.

Index of Fristat record

Physical Port

FRI Operational state Initial status is 0+1. Enumeration: 'badFriConfig': 2, 'unconnected': 1, 'idle': 3, 'active': 5, 'setup': 4.

LMI Operational state Initial status is 0+1. Enumeration: 'inactive': 1, 'error': 3, 'normal': 2.

Transmitted LMI sequence number

Received LMI sequence number

LMI errors during recorded history Statistic is zeroed at startup time.

Too Large Incoming Frames Statistic is zeroed at startup time.

Invalid dlci Incoming Frames Statistic is zeroed at startup time.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

frvcstat file.

frvcstat record.

Index of Frvcstat

Connected Component ID

Service Instance.

FRI of this PVC (FRICONF recnum)

DLCI of this PVC

PVC Operational State Initial status is 0+1. Enumeration: 'disabled': 3, 'badDLCI': 4, 'pvcUp': 12, 'pvcInit': 10, 'friError': 9, 'friDown': 8, 'free': 1, 'badPvcConfig': 2, 'pvcDown': 11, 'friFull': 6, 'noFri': 7, 'operDisabled': 5, 'pvcInactive': 13.

Transmit Congestion Status Initial status is 0+1. Enumeration: 'high': 4, 'none': 1, 'medium': 3, 'low': 2.

Receive Buffer Depletion Statistic is zeroed at startup time.

Output during last period (bytes) Statistic is zeroed at startup time.

Input during last period (bytes) Statistic is zeroed at startup time.

Data over output limit Statistic is zeroed at startup time.

Transmitted Frame Counter Statistic is zeroed at startup time.

Received Frame Counter Statistic is zeroed at startup time.

Received Frames Dropped Statistic is zeroed at startup time.

Received DE Frames Dropped Statistic is zeroed at startup time.

date & time statistics last reset

total number of records allowed in database file.

number of records in use.

friconf file.

friconf record.

Index of friconf record

Physical Port (port)

Resource pool

Maximum Frame Size (maxfrmsz) Default value is 140.

Style of LMI operation (lmitype) Default value is go4 (1+1). Enumeration: 'nolmi': 1, 'go4': 2, 'it': 4, 'ansi': 3.

Mode of FRI Operation (mode) Default value is user (0+1). Enumeration: 'net': 2, 'user': 1.

LMI's DLCI (dlci) Default value is 1023.

LMI Polling Interval (nT1) Default value is 10.

Max Time Between Polls (nT2) Default value is 15.

Max Polls per nN4 (nT3) Default value is 20.

LMI Full Status Poll Frequency (nN1) Default value is 6.

LMI Error Threshold (nN2) Default value is 2.

LMI Error History Length (nN3) Default value is 4.

Max Polls Within nT3 (nN4). Default value is 5.

Max PVCs allowed FRI (nP1) Default value is 1.

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

frvcconf file.

frvcconf record.

Index of frvcconf record

DLCI of this PVC (dlci)

FRI of this PVC (fri)

Recnum of Mapped PVC (mappedpvc)

Is this PVC enabled? (enable) Default value is yse (1+1). Enumeration: 'yes': 2, 'no': 1.

Rate Monitoring Period (t)

Committed Burst Size (bc)

Excess Burst Size (be)

Incoming BECN Threshold (n)

Receive Buffer Space (rxbufspac) Default value is 1.

Rcv Congestion Thrshld (rxcgthres)

Rcv Cong. Clear Thrshld (rxcgclear).

Operation status. Add the record to the table (valid) or delete the record from the table (invalid). Enumeration: 'valid': 1, 'invalid': 2.

total number of records allowed in database file.

number of records in use.

iticstat file.

iticstat record.

Index of iticstat record

Name of class. This field identifies which class the statistics in this record pertain to.

number of network connection commands. Total number of network originated calls to this class. Statistic is zeroed at startup time.

number of network connection failures. Total number of network connection commands that failed. Statistic is zeroed at startup time.

number of password failures. Total number of password failures for this class. Statistic is zeroed at startup time.

Current number of calls.

Average number of seconds per call.

Maximum concurrent calls.

Total number of successful modem connctions.

date & time statistics last reset

Total number of hostcalls.

300 up to 1200 baud calls received.

1200 up to 2400 baud calls received.

2400 up to 9600 baud calls received.

9600 up to 14400 baud calls received.

14400 up to 28800 baud calls received.

28800 baud calls and above received.

Calls disconnected during modem negotiation.

Calls disconnected by terminal during data transfer.

Calls disconnected during setup phase.

Calls disconnected during connection phase.

Calls disconnected during data transfer.

Calls disconnected by terminal during setup.

Calls disconnected by terminal during modem negotiation.

Number of Current Incoming Calls.

Number of Current Outgoing Calls.

Maximum number of Incoming Calls.

Maximum number of Outgoing Calls.

Number of Successful Incoming Calls.

Number of Successful Outgoing Calls.

number of network connection commands. Count of virtual circuits initiated from ITI port.

total number of records allowed in database file.

number of records in use.

itipstat file.

itipstat record.

Index of itipstat

Name of port. This field identifies which port the statistics in this record pertain to.

OBSOLETE - removed field.

accounting id.

iti class: Current user class using this port. NOTE: Order of the following fields corresponds to subset of NSCC structure. The code uses block copies for these fields and assumes the above condition is always true.

source address: Source network address.

destination address: Destination network address.

packet size: Transmit Packet size used. Enumeration: 'pkt32': 6, 'pkt128': 8, 'pkt16': 5, 'pkt1024': 11, 'pktUndefined': 1, 'pkt256': 9, 'pkt512': 10, 'pkt64': 7, 'pkt2048': 12, 'pkt4096': 13.

packet size: Receive Packet size used. Enumeration: 'pkt32': 6, 'pkt128': 8, 'pkt16': 5, 'pkt1024': 11, 'pktUndefined': 1, 'pkt256': 9, 'pkt512': 10, 'pkt64': 7, 'pkt2048': 12, 'pkt4096': 13.

window size: transmit Window size used.

window size: receive Window size used.

throughput class: transmit Throughput class used. Enumeration: 'tc1200': 8, 'tcUndefined': 1, 'tc150': 5, 'tc600': 7, 'tc2400': 9, 'tc19200': 12, 'tc9600': 11, 'tc75': 4, 'tc48000': 13, 'tc300': 6, 'tc4800': 10.

throughput class: receive Throughput class used. Enumeration: 'tc1200': 8, 'tcUndefined': 1, 'tc150': 5, 'tc600': 7, 'tc2400': 9, 'tc19200': 12, 'tc9600': 11, 'tc75': 4, 'tc48000': 13, 'tc300': 6, 'tc4800': 10.

cug type: Type of closed user group call. Enumeration: 'cug': 2, 'noCug': 1, 'bilateralCug': 4, 'cugWithOutgoingAccess': 3.

cug: Closed group identifier. Valid only if previous flag is true.

rpoa: DNIC

reverse charging: Flag indicating if reverse charging is being used. Enumeration: 'true': 2, 'busied': 3, 'false': 1, 'notapp': 4.

priority call: Flag indicating if priority calling is beng used. Enumeration: 'true': 2, 'busied': 3, 'false': 1, 'notapp': 4.

fast select: Type of fast select. Enumeration: 'fastSelect': 2, 'fastSelectRestricted': 3, 'noFastSelect': 1.

pvc code: Permanent Virtual Circuit Code.

network disconnect code. Value of the last network disconnnect code.

network diag code: Value of the last network diagnostic code.

disconnect origin: Whether disconnect was local or remote directive.

network reset code: Value of the last network reset code.

network reset diag: Value of the last network reset diagnostic code.

call originator. Flag indicating who originated the call in progress. Enumeration: 'true': 2, 'busied': 3, 'false': 1, 'notapp': 4.