REDLINE-AN50-MIB: View SNMP OID List / Download MIB

VENDOR: REDLINE COMMUNICATIONS INC.


 Home MIB: REDLINE-AN50-MIB
Download as:   
REDLINE-AN50-PMP-V1-MIB, SNMPv2-CONF, SNMPv2-TC, SNMPv2-SMI

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 redline 1.3.6.1.4.1.10728
             redlineProducts 1.3.6.1.4.1.10728.1
             redlineMgmt 1.3.6.1.4.1.10728.2
                 redlineAn50 1.3.6.1.4.1.10728.2.16
                       an50General 1.3.6.1.4.1.10728.2.16.1
                           an50GenUBR 1.3.6.1.4.1.10728.2.16.1.1 integer read-only
Indicates the system's current uncoded burst rate. With adaptive modulation enabled, this rate may change over time, depending on the prevailing propagation conditions.
                           an50GenRFLink 1.3.6.1.4.1.10728.2.16.1.2 integer read-only
connected(2) indicates the terminal is communicating properly to the remote terminal. notConnected(1) indicates there is no communication with the remote terminal. Enumeration: 'notConnected': 1, 'connected': 2.
                           an50GenFrequency 1.3.6.1.4.1.10728.2.16.1.3 integer read-write
The frequency which represents the operating channel of the link. The system can be configured to operate over 9 distinct channels.
                           an50GenAllignmentMode 1.3.6.1.4.1.10728.2.16.1.4 integer read-write
Specifies if the antenna alignment is done with buzzer or voltage. Enumeration: 'buzzer': 2, 'voltage': 1.
                           an50GenEncryptionEnabled 1.3.6.1.4.1.10728.2.16.1.5 integer read-write
Specifies if encryption is enabled or not. Enumeration: 'yes': 2, 'no': 1.
                           an50GenFlowControlEnabled 1.3.6.1.4.1.10728.2.16.1.6 integer read-write
This attribute specifies if flow control is enabled or not. Enumeration: 'yes': 2, 'no': 1.
                           an50GenHttpAccessEnabled 1.3.6.1.4.1.10728.2.16.1.7 integer read-write
This attribute specifies if Http Access is enabled or not. Enumeration: 'yes': 2, 'no': 1.
                           an50GenTelnetAccessEnabled 1.3.6.1.4.1.10728.2.16.1.8 integer read-write
This attribute specifies if Telnet Access is enabled or not. Enumeration: 'yes': 2, 'no': 1.
                           an50GenTelnetPort 1.3.6.1.4.1.10728.2.16.1.9 integer read-write
This attribute specifies the Telnet port number.
                           an50GenOptionsKey 1.3.6.1.4.1.10728.2.16.1.10 octet string read-write
This attribute specifies the Product Options Key.
                           an50GenResetDevice 1.3.6.1.4.1.10728.2.16.1.11 integer read-write
reset(2) indicates to reset the AN50 terminal. donothing(1) indicates do not reset AN50 terminal. Enumeration: 'reset': 2, 'donothing': 1.
                           an50GenFault 1.3.6.1.4.1.10728.2.16.1.12 integer read-only
The attribute specifies the Fault LED status of the terminal. Enumeration: 'on': 2, 'off': 1, 'unknown': 3.
                           an50GenTxPower 1.3.6.1.4.1.10728.2.16.1.13 integer read-only
This object specifies the actual Tx Power of the AN-50 Node in ?
                           an50GenRegisteredStations 1.3.6.1.4.1.10728.2.16.1.14 integer read-only
This object specifies the actual number of configured links.
                           an50GenRegisteredConnections 1.3.6.1.4.1.10728.2.16.1.15 integer read-only
This object specifies the actual number of configured connections.
                           an50GenActiveWirelessLinks 1.3.6.1.4.1.10728.2.16.1.16 integer read-only
This object specifies the actual number of provisioned links.
                           an50GenChannelAutoScan 1.3.6.1.4.1.10728.2.16.1.17 integer read-write
This object specifies the Auto-Scanning feature for the channel. Enumeration: 'yes': 2, 'no': 1.
                           an50GenIduType 1.3.6.1.4.1.10728.2.16.1.18 integer read-only
This object specifies the Indoor Unit Type.
                           an50GenOduType 1.3.6.1.4.1.10728.2.16.1.19 integer read-only
This object specifies the Outdoor Unit Type.
                       an50Config 1.3.6.1.4.1.10728.2.16.2
                           an50ConfigEther 1.3.6.1.4.1.10728.2.16.2.1
                               an50EtherMacAddress 1.3.6.1.4.1.10728.2.16.2.1.1 octet string read-only
This object specifies the Ethernet MAC address of the local terminal.
                               an50EtherGateway 1.3.6.1.4.1.10728.2.16.2.1.2 ipaddress read-write
The IP Gateway of the AN-50 This field is used to specify the IP address of the gateway which the AN-50 is communicating through the core network.
                               an50EtherPortStatus 1.3.6.1.4.1.10728.2.16.2.1.3 integer read-only
The attribute specifies the status of the Ethernet Port of the AN50. Enumeration: 'down': 1, 'unknown': 3, 'up': 2.
                               an50EtherIP 1.3.6.1.4.1.10728.2.16.2.1.4 ipaddress read-write
The IP address of the AN-50. The default address from the factory is 192.168.25.2. For the initial set-up, the terminal should not be connected to the Internet network, i.e. the host computer should be connected directly to the terminal Ethernet port, to avoid address conflicts with other devices in a public network. Once the IP address has been set, the terminal can be connected to the core network, where it can receive either static or dynamic addressing (DHCP) in future configuration updates.
                               an50EtherMask 1.3.6.1.4.1.10728.2.16.2.1.5 ipaddress read-write
The IP Subnet Mask of the AN-50. The value is typically set to 255.255.255.0 (Class C subnet), which prevents certain local devices from going out into the wireless network.
                               an50Ether100 1.3.6.1.4.1.10728.2.16.2.1.6 integer read-only
This object specifies the 100 Mb/s Ethernet LED status of the AN50. Enumeration: 'unknown': 3, 's10Mbs': 1, 's100Mbs': 2.
                               an50EtherFd 1.3.6.1.4.1.10728.2.16.2.1.7 integer read-only
The object specifies the Ethernet FullDuplex LED status of the AN50. Enumeration: 'unknown': 3, 'fullDuplex': 2, 'halfDuplex': 1.
                               an50EtherMgmVidEn 1.3.6.1.4.1.10728.2.16.2.1.8 integer read-write
The attribute specifies the Ethernet Management Vlan Enabled Status of the AN50. Enumeration: 'yes': 2, 'no': 1.
                               an50EtherMgmVid 1.3.6.1.4.1.10728.2.16.2.1.9 integer read-write
The attribute specifies the Ethernet Management Vlan Id of the AN50.
                               an50EtherLben 1.3.6.1.4.1.10728.2.16.2.1.10 integer read-write
The attribute specifies the Link Backup Enable Status of the AN50. Enumeration: 'yes': 2, 'no': 1.
                           an50ConfigWireless 1.3.6.1.4.1.10728.2.16.2.2
                               an50WrlsChannel 1.3.6.1.4.1.10728.2.16.2.2.1 integer read-write
specifies the operating channel of the system, within the 100 MHz available in the 5.8GHz UNII band. To avoid interference, two PTP links operating in the same physical location (co-located) or within close proximity (e.g. across the street) must be separated by at least one channel, i.e. the gap between channels should be 20 MHz or more (e.g. channels 1 and 3). Enumeration: 'chan4A': 8, 'chan3A': 6, 'chan5': 9, 'chan4': 7, 'chan1': 1, 'chan3': 5, 'chan2': 3, 'chan2A': 4, 'chan1A': 2.
                               an50WrlsTxPower 1.3.6.1.4.1.10728.2.16.2.2.2 integer read-write
The Tx Power of the AN-50 in dBm. Specifies the power level of the system, which is preset at the factory and should not be altered. In the event that this parameter needs to be changed, please contact the Redline support team.
                               an50WrlsModReduction 1.3.6.1.4.1.10728.2.16.2.2.3 integer read-write
The Modulation Reduction Level of the AN-50. Applies when the Adaptive rate is disabled. Specifies how many levels the system must drop in modulation before beginning re-transmission to address packet errors. The value can be set from 1-7, with 2 being the typical value.
                               an50WrlsAdaptiveMod 1.3.6.1.4.1.10728.2.16.2.2.4 integer read-write
Setting this attribute to AdaptiveRate(2) sets the system to operate in adaptive modulation mode. It is recommended to keep the AN-50 in this mode so that the system can automatically adjust the modulation level to the highest possible data rate based on measured RF performance. The user can define the minimum desired modulation level by setting the Main rate parameter. If the system meets this data rate, then the Signal LED on the front panel will light continuously green. If packet errors exceed one out of a million, the system will automatically lower the modulation level to maintain the link. In this case, the LED will flash green. If errors continue when the system reaches the lowest modulation level, the LED will flash red to indicate a failed RF link. The user can also disable the dynamic modulation mode by disabling Adaptive Modulation. In this mode, the user is required to set the Burst Rate and the Modulation Reduction Level. It is recommended not to operate the system in manual mode, as this mode is intended primarily for field support. Note the Signal LED will light solid green when the packet error rate is less than 1 out of a million. When the errors exceed this limit, the LED will not illuminate, indicating the RF link has failed. Enumeration: 'notAdaptiveRate': 1, 'adaptiveRate': 2.
                               an50WrlsUBR 1.3.6.1.4.1.10728.2.16.2.2.5 integer read-write
This object contains the desired net uncoded burst rate for the link. Set uncoded burst rate in steps (0=6Mb/s, 1=9Mb/s, 2=12Mb/s, 3=18Mb/s, 4=24Mb/s, 5=36Mb/s, 6=48Mb/s, 7=54Mbs).
                               an50WrlsMaster 1.3.6.1.4.1.10728.2.16.2.2.6 integer read-write
The object contains the configured mode of the AN50 terminal. 1 = PTP Slave, 2 = PTP Master, 3 = PMP Slave, 4 = PMP Master Enumeration: 'pmpSlave': 3, 'pmpMaster': 4, 'ptpSlave': 1, 'ptpMaster': 2.
                               an50WrlsVersion 1.3.6.1.4.1.10728.2.16.2.2.7 integer read-write
Sets the version of the AN50 system software. The software can be remotely downloaded into the AN50. The system comprises sufficient memory to hold two independent software loads. The operator can specify which load to set as the active version. Enumeration: 'secondFlash': 2, 'firstFlash': 1.
                               an50WrlsEncryptCode 1.3.6.1.4.1.10728.2.16.2.2.8 octet string read-write
The object contains the Encryption Key used for the AN-50 terminal. Enter the MAC address of the remote terminal to enable over-the-air data encryption.
                               an50WrlsCableAttenuation 1.3.6.1.4.1.10728.2.16.2.2.9 integer read-only
This object contains the Cable Attenuation for the AN-50 in dB.
                               an50WrlsRfPortStatus 1.3.6.1.4.1.10728.2.16.2.2.10 integer read-only
The object specifies the status of the AN50s Wireless Port. Enumeration: 'down': 1, 'unknown': 3, 'up': 2.
                               an50WrlsSaveConfig 1.3.6.1.4.1.10728.2.16.2.2.11 integer read-write
The object saves the entire config set of the AN50. Enumeration: 'donothing': 1, 'saveConfig': 2.
                               an50WrlsActivateConfig 1.3.6.1.4.1.10728.2.16.2.2.12 integer read-write
The object activates the entire config set of the AN50. Enumeration: 'activeConfig': 2, 'donothing': 1.
                               an50WrlsRadioEnable 1.3.6.1.4.1.10728.2.16.2.2.13 integer read-write
The object specifies whether radio transmission is enabled or disabled. Enumeration: 'txOn': 2, 'txOff': 1.
                               an50WrlsRfStatusErrorCode 1.3.6.1.4.1.10728.2.16.2.2.14 integer read-only
The object specifies the Error Code for the RF Status.
                               an50WrlsRfSignal 1.3.6.1.4.1.10728.2.16.2.2.15 integer read-only
The object specifies the Wireless Signal LED status. Enumeration: 'on': 2, 'off': 1, 'blinking': 3.
                               an50WrlsLLMode 1.3.6.1.4.1.10728.2.16.2.2.16 integer read-write
Link length set mode. Enumeration: 'auto': 1, 'manual': 2.
                               an50WrlsLMU 1.3.6.1.4.1.10728.2.16.2.2.17 integer read-write
This object specifies the Link measurements unit (mile / Km). Enumeration: 'mile': 1, 'km': 2.
                               an50WrlsLL 1.3.6.1.4.1.10728.2.16.2.2.18 integer read-write
This object specifies the Link Length. See an50WrlsLMU object for units.
                               an50ConfigScheduler 1.3.6.1.4.1.10728.2.16.2.2.19
                                     an50WrlsFrameSize 1.3.6.1.4.1.10728.2.16.2.2.19.1 integer read-write
This object specifies the size of wireless frame (DL+RTD+UL) in micro seconds.
                                     an50WrlsMinBlockSize 1.3.6.1.4.1.10728.2.16.2.2.19.2 integer read-write
This object specifies a minimum number of bytes comprising transmitted block.
                                     an50WrlsDownlinkSize 1.3.6.1.4.1.10728.2.16.2.2.19.3 integer read-write
This object specifies the size of downlink sub-frame in micro seconds.
                                     an50WrlsRoundTripDelay 1.3.6.1.4.1.10728.2.16.2.2.19.4 integer read-write
This object specifies the round trip delay in micro seconds.
                                     an50WrlsAdaptiveDLSize 1.3.6.1.4.1.10728.2.16.2.2.19.5 integer read-write
This object specifies if adaptive downlink size is enabled or disabled. Enumeration: 'on': 2, 'off': 1.
                                     an50WrlsExtSyncronize 1.3.6.1.4.1.10728.2.16.2.2.19.6 integer read-write
This object specifies if external synchronization is enabled or disabled. Enumeration: 'on': 2, 'off': 1.
                                     an50WrlsMaximumDistance 1.3.6.1.4.1.10728.2.16.2.2.19.7 integer read-write
This object specifies the maximum distance between base station and subscriber station in Km.
                                     an50WrlsRegistrationPeriod 1.3.6.1.4.1.10728.2.16.2.2.19.8 integer read-write
This object specifies the number of frames between registration periods.
                               an50ConfigDefGroup 1.3.6.1.4.1.10728.2.16.2.2.20
                                     an50WrlsBroadcastDLCIR 1.3.6.1.4.1.10728.2.16.2.2.20.1 integer read-write
This object specifies the broadcast downlink commited rate in kb/s.
                                     an50WrlsBroadcastDLPIR 1.3.6.1.4.1.10728.2.16.2.2.20.2 integer read-write
This object specifies the broadcast downlink peak rate in kb/s.
                               an50WrlsDFSAction 1.3.6.1.4.1.10728.2.16.2.2.21 integer read-write
This object specifies the action taken when another system is detected on the same frequency Enumeration: 'none': 1, 'changeFreq': 3, 'txDisabled': 2.
                               an50WrlsAntennaGain 1.3.6.1.4.1.10728.2.16.2.2.22 integer read-write
Antenna Gain in dB.
                               an50WrlsATPEnabled 1.3.6.1.4.1.10728.2.16.2.2.23 integer read-write
This object specifies if the Automatic Transmitted Power Control is enabled Enumeration: 'yes': 2, 'no': 1.
                           an50Sw 1.3.6.1.4.1.10728.2.16.2.3
                               an50SwServer 1.3.6.1.4.1.10728.2.16.2.3.1 ipaddress read-write
The address of the TFTP server used for software upgrades. If the address of the TFTP server is unknown, return 0.0.0.0.
                               an50SwFilename 1.3.6.1.4.1.10728.2.16.2.3.2 octet string read-write
The file name of the software image to be loaded into this device.
                               an50SwAdminStatus 1.3.6.1.4.1.10728.2.16.2.3.3 integer read-write
If set to upgrade(2), the device will initiate a TFTP software image download using an50SwFilename. If the download process is interrupted by a reset or power failure, the device will load the previous image. If set to noUpgrade(1), the device will revert to the previous version of the software. At initial startup, this object has the default value of noUpgrade(1). Enumeration: 'upgrade': 2, 'noUpgrade': 1.
                               an50SwOperStatus 1.3.6.1.4.1.10728.2.16.2.3.4 integer read-only
This object shows the download status. inProgress(1) indicates that a TFTP download is underway completeSuccess(2) indicates that the last software upgrade was successful failed(3) indicates that the last attempted download failed, ordinarily due to TFTP timeout. Enumeration: 'completeSuccess': 2, 'inProgress': 1, 'other': 4, 'failed': 3.
                               an50SwCurrentVers 1.3.6.1.4.1.10728.2.16.2.3.5 octet string read-only
The software version currently operating in this device's flash. This object should be in the syntax used by the individual vendor to identify software versions. If it is not applicable, this MUST contain an empty string.
                               an50SwOtherVers 1.3.6.1.4.1.10728.2.16.2.3.6 octet string read-only
The software version in the secondary flash. This object should be in the syntax used by the individual vendor to identify software versions. If it is not applicable, this MUST contain an empty string.
                       an50Pm 1.3.6.1.4.1.10728.2.16.3
                           an50ResetStatistics 1.3.6.1.4.1.10728.2.16.3.1 integer read-write
A value of reset(2) resets the performance statistics on the AN-50, a value of donothing(1) does nothing. Enumeration: 'reset': 2, 'donothing': 1.
                           an50PmEther 1.3.6.1.4.1.10728.2.16.3.2
                               an50PmEtherRxPackets 1.3.6.1.4.1.10728.2.16.3.2.1 counter read-only
This object counts the number of ethernet packets successfully received by the local system.
                               an50PmEtherRxPacketsErr 1.3.6.1.4.1.10728.2.16.3.2.2 counter read-only
This object counts the number of ethernet packet errors received by the local system.
                               an50PmEtherTxPackets 1.3.6.1.4.1.10728.2.16.3.2.3 counter read-only
This object counts the number of Ethernet packets transmitted by the local system.
                               an50PmEtherTxPacketsErr 1.3.6.1.4.1.10728.2.16.3.2.4 counter read-only
This object counts the number of Ethernet error packets transmitted by the local system.
                               an50PmEtherRxPacketsDisc 1.3.6.1.4.1.10728.2.16.3.2.5 counter read-only
This object counts the number of ethernet packets discarded by receiver.
                               an50PmEtherTxPacketsDisc 1.3.6.1.4.1.10728.2.16.3.2.6 counter read-only
This object counts the number of ethernet packets discarded by transmitter.
                           an50PmWrls 1.3.6.1.4.1.10728.2.16.3.3
                               an50PmWrlsRxSigMin 1.3.6.1.4.1.10728.2.16.3.3.1 integer read-only
This object indicates the minimum received signal strength measured since the last SNMP update.
                               an50PmWrlsRxSigMean 1.3.6.1.4.1.10728.2.16.3.3.2 integer read-only
This object indicates the average received signal strength measured since the last SNMP update.
                               an50PmWrlsRxSigMax 1.3.6.1.4.1.10728.2.16.3.3.3 integer read-only
This object indicates the maximum received signal strength measured since the last SNMP update
                               an50PmWrlsAvgSinAdr 1.3.6.1.4.1.10728.2.16.3.3.4 integer read-only
This object indicates the average signal to noise ratio measured since the last SNMP update. The ratio is based on the digital information provided from the output of the AtoD converter.
                               an50PmWrlsRxPackets 1.3.6.1.4.1.10728.2.16.3.3.5 counter read-only
This object indicates the number of packets received over the air from the remote terminal.
                               an50PmWrlsRxPacketsRetx 1.3.6.1.4.1.10728.2.16.3.3.6 counter read-only
This object indicates the number of packets retransmitted over the air from the remoter terminal.
                               an50PmWrlsRxPacketsDisc 1.3.6.1.4.1.10728.2.16.3.3.7 counter read-only
This object indicates the number of packets, originating from the remote terminal lost over the air due to degradation in the RF link.
                               an50PmWrlsTxPackets 1.3.6.1.4.1.10728.2.16.3.3.8 counter read-only
This object indicates the number of wireless packets (including Ethernet frames and error correction bytes) transmitted over the air by the local terminal.
                               an50PmWrlsTxPacketsRetx 1.3.6.1.4.1.10728.2.16.3.3.9 counter read-only
This object indicates the number of packets retransmitted over the air by the local terminal. The retransmission scheme is based on the Acknowledge/Request (ARQ) algorithm that detects when packets are lost and makes a request to the MAC scheduler to repeat transmission of the lost packets.
                               an50PmWrlsTxPacketsDisc 1.3.6.1.4.1.10728.2.16.3.3.10 counter read-only
This object indicates the total number of packets lost over the air due to degradation in the RF link.
                               an50PmWrlsCalcDst 1.3.6.1.4.1.10728.2.16.3.3.11 integer read-only
This object contains the calculated link distance.
                       an50Trap 1.3.6.1.4.1.10728.2.16.4
                           an50SysLastTrapTime 1.3.6.1.4.1.10728.2.16.4.1 timeticks read-only
The value of system.sysUpTime when the last trap was generated. If no traps have been generated since the last reset, this attribute has a value of 0. No trap is issued as a result of a change to this value.
                       an50LinkPmp 1.3.6.1.4.1.10728.2.16.5
                           an50MaxCid 1.3.6.1.4.1.10728.2.16.5.1 integer read-only
The object contains the maximum number of CID for this equipment
                           an50LinkCurrentAvailId 1.3.6.1.4.1.10728.2.16.5.2 integer read-only
The current available ID in the Links table that is queried by NMS before creating a new row in Link Table
               an50TftpFailTrap 1.3.6.1.4.1.107280.1
An event to report the failure of a Software Download.
               an50TftpSuccessTrap 1.3.6.1.4.1.107280.2
An event to report the success of a Software Download.
               an50PswdChangeFailTrap 1.3.6.1.4.1.107280.3
An event to report the failure of a password change.
               an50FirmwareConfigFailTrap 1.3.6.1.4.1.107280.4
An event to report the failure of a firmware config.
               an50EepromCorruptedTrap 1.3.6.1.4.1.107280.5
An event to report the corruption of the EEPROM.
               an50PowerSupplyFailureTrap 1.3.6.1.4.1.107280.6
An event to report the power supply failure.
               an50SaveConfigTrap 1.3.6.1.4.1.107280.7
An event to report the saving of configuration
               an50ModifiedIDTrap 1.3.6.1.4.1.107280.8
An event to report the modification in the configuration of a CID
               an50pmpRegistrationMissed 1.3.6.1.4.1.107280.9
An event to report the missing of the registration by a AN50 Subscriber to one BS.This trap is sent by the BS and contains the MAC address of the SS missing the registration
               an50pmpRegistrationSuccessful 1.3.6.1.4.1.107280.10
An event to report the successful registration of an AN50 Subscriber to BS. This trap is sent by the BS and contains the MAC address of the newly registered SS
               an50DFSEvent 1.3.6.1.4.1.107280.11
An event to report a dynamic frequency selection (DFS) event in AN50