LINK-BUNDLING-MIB: View SNMP OID List / Download MIB

VENDOR: INTERNET-STANDARD


 Home MIB: LINK-BUNDLING-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 linkBundlingMIB 1.3.6.1.2.1.1
This MIB contains managed object definitions for MPLS traffic engineering link bundling as defined in: Kompella, K., Rekhter, Y., Berger, L., Link Bundling in MPLS Traffic Engineering Internet Draft , July 2002.
     linkBundlingNotifications 1.3.6.1.2.1.1.0
         linkBundleMismatch 1.3.6.1.2.1.1.0.1
This notification is generated when a mismatch is found on a bundled link. Such mismatch can be detected for instance if one of the traffic engineering parameters is not consistent across all TE links within a bundled link (resource class, OSPF link type, etc.).
     linkBundlingObjects 1.3.6.1.2.1.1.1
         teLinkTable 1.3.6.1.2.1.1.1.1 no-access
This table specifies the grouping of component links into TE links and grouping of TE links into bundled links.
             teLinkEntry 1.3.6.1.2.1.1.1.1.1 no-access
An entry in this table exists for each ifEntry with an ifType of teLink(TBD), i.e. for every TE link. An ifEntry in the ifTable must exist before a teLinkEntry is created with the corresponding ifIndex. If a TE link entry in the ifTable is destroyed, then so is the corresponding entry in the teLinkTable. The administrative and operational status values are controlled from the ifEntry. If the link is unnumbered, ifIndex is also used as the outgoing interface identifier.
                 teLinkIpAddrType 1.3.6.1.2.1.1.1.1.1.1 inetaddresstype read-only
For IPv4 and IPv6 numbered links, this object represents the IP address type associated with the TE link. For unnumbered links, a value of unknown(0) must be used.
                 teLinkIpAddr 1.3.6.1.2.1.1.1.1.1.2 inetaddress read-only
For IPv4 and IPv6 numbered links, this object represents the IP address associated with the TE link.
                 teLinkRemoteIpAddr 1.3.6.1.2.1.1.1.1.1.3 inetaddress read-only
The remote IP address associated with the TE link (IPv4 and IPv6 numbered links).
                 teLinkMetric 1.3.6.1.2.1.1.1.1.1.4 unsigned32 read-only
The traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric.
                 teLinkMuxCapability 1.3.6.1.2.1.1.1.1.1.5 integer read-only
This attribute specifies link multiplex capability of the TE link, which is derived from its component links. All component links within the same TE link must have the same link multiplex capability. Enumeration: 'fiberSwitch': 200, 'tdm': 100, 'packetSwitch1': 1, 'packetSwitch3': 3, 'packetSwitch2': 2, 'packetSwitch4': 4, 'lambdaSwitch': 150, 'layer2Switch': 51.
                 teLinkProtectionType 1.3.6.1.2.1.1.1.1.1.6 integer read-only
This attribute specifies link protection type of the TE link. Enumeration: 'dedicated1For1': 4, 'unprotected': 2, 'enhanced': 6, 'shared': 3, 'extraTraffic': 1, 'dedicated1Plus1': 5.
                 teLinkWorkingPriority 1.3.6.1.2.1.1.1.1.1.7 unsigned32 read-only
This object represents a priority value such that a new connection with a higher priority, i.e. numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link.
                 teLinkResourceClass 1.3.6.1.2.1.1.1.1.1.8 unsigned32 read-only
This attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within a link bundle must have the same resource class.
                 teLinkIncomingIfId 1.3.6.1.2.1.1.1.1.1.9 interfaceindexorzero read-only
For unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link.
                 teLinkOutgoingIfId 1.3.6.1.2.1.1.1.1.1.10 interfaceindexorzero read-only
If the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR.
                 teLinkFlooding 1.3.6.1.2.1.1.1.1.1.11 interfaceindexorzero read-only
This object only has significance for link bundles which encoding type is not clear. For these link bundles, this object identifies the TE link on which to restrict flooding. If the value is zero, then flooding must be done on all TE links within the link bundle.
                 teLinkRowStatus 1.3.6.1.2.1.1.1.1.1.12 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkRowStatus is active.
                 teLinkStorageType 1.3.6.1.2.1.1.1.1.1.13 storagetype read-only
The storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         teLinkDescriptorTable 1.3.6.1.2.1.1.1.2 no-access
This table specifies the link descriptors associated with the TE links.
             teLinkDescriptorEntry 1.3.6.1.2.1.1.1.2.1 no-access
An entry in this table is created for every TE link descriptor. An ifEntry in the ifTable must exist before a teLinkDescriptorEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkDescriptorTable that use the ifIndex of this TE link.
                 teLinkDescriptorId 1.3.6.1.2.1.1.1.2.1.1 unsigned32 no-access
This object specifies the link descriptor identifier.
                 teLinkEncodingType 1.3.6.1.2.1.1.1.2.1.2 integer read-only
This attribute specifies the TE link encoding type. Enumeration: 'fiber': 9, 'fiberChannel': 11, 'ansiEtsiPdh': 3, 'packet': 1, 'sdhItuSonetAnsi': 5, 'digitalWrapper': 7, 'ethernet': 2, 'lambda': 8.
                 teLinkDescrPriority 1.3.6.1.2.1.1.1.2.1.3 unsigned32 read-only
This object specifies the lowest priority at which that link encoding type is available.
                 teLinkMinReservableBandwidth 1.3.6.1.2.1.1.1.2.1.4 unsigned32 read-only
This attribute specifies the minimum reservable bandwidth on the TE link. This is derived from the union of the minimum reservable bandwidth of all the component links associated with the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second.
                 teLinkMaxReservableBandwidth 1.3.6.1.2.1.1.1.2.1.5 unsigned32 read-only
This attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second.
                 teLinkDescrRowStatus 1.3.6.1.2.1.1.1.2.1.6 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkDescrRowStatus is active.
                 teLinkDescrStorageType 1.3.6.1.2.1.1.1.2.1.7 storagetype read-only
The storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         teLinkOspfTeTable 1.3.6.1.2.1.1.1.3 no-access
This table specifies the OSPF traffic engineering information associated with TE links.
             teLinkOspfTeEntry 1.3.6.1.2.1.1.1.3.1 no-access
If OSPF is enabled, an entry in this table is created for every TE link.
                 teLinkOspfLinkType 1.3.6.1.2.1.1.1.3.1.1 integer read-only
This attribute specifies the OSPF link type for the TE link. All TE links within the same bundle must have the same link type. Enumeration: 'multiAccess': 2, 'pointToPoint': 1.
                 teLinkOspfLinkId 1.3.6.1.2.1.1.1.3.1.2 routerid read-only
On point-to-point link, the link identifier is the Router ID of the neighbor. For bundled link, is derived from the link identifier associated with its TE links.
         teLinkSrlgTable 1.3.6.1.2.1.1.1.4 no-access
This table specifies the SRLGs associated with TE links.
             teLinkSrlgEntry 1.3.6.1.2.1.1.1.4.1 no-access
An entry in this table contains information about a SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkSrlgTable that use the ifIndex of this TE link.
                 srlg 1.3.6.1.2.1.1.1.4.1.1 unsigned32 no-access
This identifies a SRLG supported by the TE link.
                 srlgRowStatus 1.3.6.1.2.1.1.1.4.1.2 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when srlgRowStatus is active.
                 srlgStorageType 1.3.6.1.2.1.1.1.4.1.3 storagetype read-only
The storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         teLinkBandwidthTable 1.3.6.1.2.1.1.1.5 no-access
This table specifies the priority-based bandwidth table for TE links.
             teLinkBandwidthEntry 1.3.6.1.2.1.1.1.5.1 no-access
An entry in this table contains information about the priority-based bandwidth of TE links. An ifEntry in the ifTable must exist before a teLinkBandwidthEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkBandwidthTable that use the ifIndex of this TE link.
                 teLinkPriority 1.3.6.1.2.1.1.1.5.1.1 unsigned32 no-access
This attribute specifies the priority. It should be mapped to a number between 0 and 7
                 teLinkUnreservedBandwidth 1.3.6.1.2.1.1.1.5.1.2 unsigned32 read-only
This attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second.
                 teLinkMaximumLspBandwidth 1.3.6.1.2.1.1.1.5.1.3 unsigned32 read-only
This attribute specifies the TE link maximum LSP bandwidth at priority p. It is the maximum of all maximum LSP bandwidth at priority p of the component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second.
                 teLinkBandwidthRowStatus 1.3.6.1.2.1.1.1.5.1.4 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkBandwidthRowStatus is active.
                 teLinkBandwidthStorageType 1.3.6.1.2.1.1.1.5.1.5 storagetype read-only
The storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         componentLinkTable 1.3.6.1.2.1.1.1.6 no-access
This table specifies the component link parameters.
             componentLinkEntry 1.3.6.1.2.1.1.1.6.1 no-access
An entry in this table exists for each ifEntry that represents a component link. An ifEntry must exist in the ifTable before a componentLinkEntry is created with the corresponding ifIndex. If an entry representing a component link is destroyed in the ifTable, then so is the corresponding entry in the componentLinkTable. The administrative and operational status values are controlled from the ifEntry.
                 componentLinkMuxCapability 1.3.6.1.2.1.1.1.6.1.1 integer read-only
This attribute specifies link multiplexing capabilities of the component link. Enumeration: 'fiberSwitch': 200, 'tdm': 100, 'packetSwitch1': 1, 'packetSwitch3': 3, 'packetSwitch2': 2, 'packetSwitch4': 4, 'lambdaSwitch': 150, 'layer2Switch': 51.
                 componentLinkPreferredProtection 1.3.6.1.2.1.1.1.6.1.2 integer read-only
This attribute specifies whether this component link is a primary or secondary entity. Enumeration: 'primary': 1, 'secondary': 2.
                 componentLinkCurrentProtection 1.3.6.1.2.1.1.1.6.1.3 integer read-only
This attribute specifies whether this component link is currently used as primary or secondary link. Enumeration: 'primary': 1, 'secondary': 2.
                 componentLinkRowStatus 1.3.6.1.2.1.1.1.6.1.4 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkRowStatus is active.
                 componentLinkStorageType 1.3.6.1.2.1.1.1.6.1.5 storagetype read-only
The storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         componentLinkDescriptorTable 1.3.6.1.2.1.1.1.7 no-access
This table specifies the link descriptors associated with the component links.
             componentLinkDescriptorEntry 1.3.6.1.2.1.1.1.7.1 no-access
An entry in this table is created for every component link descriptor. An ifEntry in the ifTable must exist before a componentLinkDescriptorEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkDescriptorTable that use the ifIndex of this component link.
                 componentLinkDescrId 1.3.6.1.2.1.1.1.7.1.1 unsigned32 no-access
This object specifies the link descriptor identifier.
                 componentLinkEncodingType 1.3.6.1.2.1.1.1.7.1.2 integer read-only
This attribute specifies the component link encoding type. Enumeration: 'fiber': 9, 'fiberChannel': 11, 'ansiEtsiPdh': 3, 'packet': 1, 'sdhItuSonetAnsi': 5, 'digitalWrapper': 7, 'ethernet': 2, 'lambda': 8.
                 componentLinkDescrPriority 1.3.6.1.2.1.1.1.7.1.3 unsigned32 read-only
This object specifies the lowest priority at which that link encoding type is available for the component link.
                 componentLinkMinReservBandwidth 1.3.6.1.2.1.1.1.7.1.4 unsigned32 read-only
This attribute specifies the minimum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second.
                 componentLinkMaxReservBandwidth 1.3.6.1.2.1.1.1.7.1.5 unsigned32 read-only
This attribute specifies the maximum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second.
                 componentLinkDescrRowStatus 1.3.6.1.2.1.1.1.7.1.6 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkDescrRowStatus is active.
                 componentLinkDescrStorageType 1.3.6.1.2.1.1.1.7.1.7 storagetype read-only
The storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         componentLinkBandwidthTable 1.3.6.1.2.1.1.1.8 no-access
This table specifies the priority-based bandwidth for component links.
             componentLinkBandwidthEntry 1.3.6.1.2.1.1.1.8.1 no-access
An entry in this table contains information about the priority-based bandwidth on component links. An ifEntry in the ifTable must exist before a componentLinkBandwidthEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkBandwidthTable that use the ifIndex of this component link.
                 componentLinkPriority 1.3.6.1.2.1.1.1.8.1.1 unsigned32 no-access
This attribute specifies the priority. It should be mapped to a number between 0 and 7.
                 componentLinkUnreservedBandwidth 1.3.6.1.2.1.1.1.8.1.2 unsigned32 read-only
This attribute specifies the component link unreserved bandwidth at priority p. This value is an estimate in units of 1,000 bits per second.
                 componentLinkMaximumLspBandwidth 1.3.6.1.2.1.1.1.8.1.3 unsigned32 read-only
This attribute specifies the component link maximum LSP bandwidth at priority p. This value is an estimate in units of 1,000 bits per second.
                 componentLinkBandwidthRowStatus 1.3.6.1.2.1.1.1.8.1.4 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkBandwidthRowStatus is active.
                 componentLinkBwStorageType 1.3.6.1.2.1.1.1.8.1.5 storagetype read-only
The storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
         linkBundlingNotifEnable 1.3.6.1.2.1.1.1.9 truthvalue read-write
If this object is true, then it enables the generation of the link bundling notifications, otherwise these notifications are not emitted.
     linkBundlingConformance 1.3.6.1.2.1.1.2
         linkBundlingGroups 1.3.6.1.2.1.1.2.1
             linkBundlingGroup 1.3.6.1.2.1.1.2.1.1
Collection of objects needed for the monitoring of resources associated with TE links.
             teLinkOspfTeGroup 1.3.6.1.2.1.1.2.1.2
Collection of objects needed for the OSPF traffic engineering parameters of TE links.
             teLinkSrlgGroup 1.3.6.1.2.1.1.2.1.3
Collection of objects needed for the monitoring of SRLG resources associated with TE links.
             teLinkBandwidthGroup 1.3.6.1.2.1.1.2.1.4
Collection of objects needed for the monitoring of the priority-based bandwidth resources associated with TE links and component links.
             componentLinkBandwidthGroup 1.3.6.1.2.1.1.2.1.5
Collection of objects needed for the monitoring of bandwidth parameters associated with component links.
             linkBundlingNotificationGroup 1.3.6.1.2.1.1.2.1.6
Set of notifications implemented in this module. None is mandatory.
         linkBundlingCompliances 1.3.6.1.2.1.1.2.2
             linkBundlingFullModuleCompliance 1.3.6.1.2.1.1.2.2.1
Compliance statement for agents that support the configuration and monitoring of link bundling MIB.
             linkBundlingMonModuleCompliance 1.3.6.1.2.1.1.2.2.2
Compliance statement for agents that support the monitoring of link bundling MIB.