Juniper-PPP-MIB: View SNMP OID List / Download MIB

VENDOR: JUNIPER


 Home MIB: Juniper-PPP-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, Juniper-MIBs, Juniper-TC, SNMPv2-TC, IPV6-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 juniPppMIB 1.3.6.1.4.1.4874.2.2.11
The Point-to-Point Protocol (PPP) MIB for the Juniper enterprise.
       juniPppObjects 1.3.6.1.4.1.4874.2.2.11.1
           juniPppLcp 1.3.6.1.4.1.4874.2.2.11.1.1
               juniPppLinkStatusTable 1.3.6.1.4.1.4874.2.2.11.1.1.1 no-access
This table contains entries for PPP interfaces present in the system.
                   juniPppLinkStatusEntry 1.3.6.1.4.1.4874.2.2.11.1.1.1.1 no-access
Each entry describes the characteristics of a PPP interface.
                       juniPppLinkStatusTerminateReason 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.1 integer read-only
Reason the PPP link was terminated: none None. other Not specified. adminDisable Interface administratively disabled. lowerLayerDown Underlying interface is down. noUpperInterface No interface above PPP. authenticationFailure Authentication failed. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate LCP option. See juniPppLinkStatusTerminateNegFailOption. keepaliveFailure Keepalive failed. sessionTimeout Maximum session period expired. inactivityTimeout Maximum inactivity period expired. addressLeaseExpired Lease for network address expired. adminLogout Session administratively terminated. tunnelFailed Associated tunnel failed. tunnelDisconnected Associated tunnel disconnected. loopback Loopback detected. Enumeration: 'keepaliveFailure': 10, 'none': 0, 'tunnelDisconnected': 16, 'lowerLayerDown': 3, 'addressLeaseExpired': 13, 'peerRenegotiated': 7, 'loopback': 17, 'tunnelFailed': 15, 'authenticationFailure': 5, 'peerTerminated': 6, 'inactivityTimeout': 12, 'other': 1, 'negotiationFailure': 9, 'adminLogout': 14, 'sessionTimeout': 11, 'noUpperInterface': 4, 'maxRetriesExceeded': 8, 'adminDisable': 2.
                       juniPppLinkStatusTerminateNegFailOption 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.2 integer read-only
Reports the PPP LCP option for which negotiation failed, when juniPppLinkStatusTerminateReason has the value 'negotiationFailure'. Enumeration: 'localToRemoteACCompression': 8, 'remoteMagicNumber': 5, 'none': 0, 'remoteMr': 3, 'localAuthentication': 6, 'localMagicNumber': 4, 'other': 1, 'localMr': 2, 'localToRemoteProtocolCompression': 7.
                       juniPppLinkStatusInKeepaliveRequests 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.3 counter32 read-only
Number of keepalive requests received.
                       juniPppLinkStatusOutKeepaliveRequests 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.4 counter32 read-only
Number of keepalive requests transmitted.
                       juniPppLinkStatusInKeepaliveReplies 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.5 counter32 read-only
Number of keepalive replies received.
                       juniPppLinkStatusOutKeepaliveReplies 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.6 counter32 read-only
Number of keepalive replies transmitted.
                       juniPppLinkStatusKeepaliveFailures 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.7 counter32 read-only
Number of keepalive failures detected.
                       juniPppLinkStatusLocalMagicNumber 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.8 integer32 read-only
Magic number negotiated for the local side.
                       juniPppLinkStatusRemoteMagicNumber 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.9 integer32 read-only
Magic number negotiated for the remote side.
                       juniPppLinkStatusLocalAuthentication 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.10 junipppauthentication2 read-only
Authentication protocol negotiated for the local side.
                       juniPppLinkStatusTunnelIfIndex 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.11 interfaceindexorzero read-only
The ifIndex of an associated interface pertaining to a tunneling protocol, or zero if no such interface exists. The type of tunneling interface can be identified from information in the entries in ifTable and juniIfTable for this tunnel interface.
                       juniPppLinkStatuslcpRenegoTerminates 1.3.6.1.4.1.4874.2.2.11.1.1.1.1.12 counter32 read-only
Number of times lcp terminated due to peer exceeding max renegotiation attempts.
               juniPppLinkConfigTable 1.3.6.1.4.1.4874.2.2.11.1.1.2 no-access
This table contains entries for PPP interfaces present in the system.
                   juniPppLinkConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.1.2.1 no-access
Each entry describes the characteristics of a PPP interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
                       juniPppLinkConfigIfIndex 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.1 interfaceindex no-access
The ifIndex of the PPP interface. When creating entries in this table, suitable values for this object are determined by reading juniPppNextIfIndex.
                       juniPppLinkConfigRowStatus 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.2 rowstatus read-only
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniPppLinkConfigRowStatus juniPppLinkConfigLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniPppLinkConfigIndex must have been determined previously, by reading juniPppNextIfIndex. The interface identified by juniPppLinkConfigLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
                       juniPppLinkConfigLowerIfIndex 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.3 interfaceindexorzero read-only
The ifIndex of an interface over which this PPP interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a non-zero value be configured at entry creation.
                       juniPppLinkConfigKeepalive 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.4 integer32 read-only
Keepalive interval in seconds. A value of zero disables keepalive. Keepalive is performed using LCP Echo.
                       juniPppLinkConfigAuthentication 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.5 junipppauthentication read-only
Specifies the type(s) of authentication, if any, to be negotiated with the peer: none No authentication is negotiated. pap PAP negotiation only. chap CHAP negotiation only. papChap PAP negotiation is attempted first; if fails, attempt CHAP. chapPap CHAP negotiation is attempted first; if fails, attempt PAP. If authentication negotiation is not supported for this PPP interface, then any attempt to explicitely set this object will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation. Setting this object to none(0) will set juniPppLinkConfigAuthenticatorVirtualRouter object to an empty string. This object returns a null(0) value on the get operation. New object juniPppLinkConfigAuthentication2 will reflect the configured values. Setting this object along with the juniPppLinkConfigAuthentication2 object will return an inconsistentValue error.
                       juniPppLinkConfigMaxAuthenRetries 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.6 integer32 read-only
The number of authentication retries permitted, in addition to a failed initial attempt. If all retries fail, the link is reset. If authentication negotiation is not supported for this PPP interface, then any attempt to explicitely set this object will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation.
                       juniPppLinkConfigStandardIfIndex 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.7 interfaceindex read-only
The ifIndex value for this interface in the standard PPP MIBs. The ifIndex value for PPP interfaces is not the same for both proprietary and standard MIB tables pertaining to PPP interface. Therefore this value is provide to simply cross referencing standard PPP and proprietary PPP MIB information.
                       juniPppLinkConfigChapMinChallengeLength 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.8 integer32 read-only
Minimum value of the CHAP authenticator challenge length value. This value is never allowed to be set to a value greater than juniPppLinkConfigChapMaxChallengeLength.
                       juniPppLinkConfigChapMaxChallengeLength 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.9 integer32 read-only
Maximum value of the CHAP authenticator challenge length value. This value is never allowed to be set to a value less than juniPppLinkConfigChapMinChallengeLength.
                       juniPppLinkConfigPassiveMode 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.10 junienable read-only
When enabled, LCP state machine is forced into passive mode on lower layer UP message. It adds compatibility with slow and buggy clients.
                       juniPppLinkConfigAuthenticatorVirtualRouter 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.11 juniname read-only
The name of the virtual router (Juniper-ROUTER-MIB.juniRouterName) to be used for authentication on the PPP interface. Setting this object statically binds the authenticating virtual router with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned. Setting this object to a non-null string returns inconsistentValue error if juniPppLinkConfigAuthentication object is none(0) or not configured.
                       juniPppLinkConfigAaaProfile 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.12 juniname read-only
The name of the AAA profile to be used for authentication on the PPP interface. Setting this object statically binds the AAA profile with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored. On a Set operation, if the value of this object is not null and does not correspond to an existing AAA profile, then an inconsistentValue error is returned.
                       juniPppLinkConfigAuthentication2 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.13 juninibbleconfig read-only
A configuration variable comprised of nibbles i.e. 4 bits, such that a client can supply a list of 0 to 8 selections. The least significant nibble is the first value of the list, and the most significant nibble is the last value. The value in each field ranges from 0 to 15, however the first nibble with value 0 indicates the end of the list. Repetition of values is not allowed. Segregation of values is not allowed. Valid Values are: none - 0 pap - 1 chap - 2 eap - 3 Example valid encoding: 0x00000321 0x00000012 Not a valid encoding: 0x00000121 0x01002001 If authentication negotiation is not supported for this PPP interface, then any attempt to explicitly set this object will result in a notWritable error and it will be implicitly set to the DEFVAL on row creation. Setting this object to null will set juniPppLinkConfigAuthenticatorVirtualRouter object to an empty string. Setting this object along with the juniPppLinkConfigAuthentication object will return an inconsistentValue error.
                       juniPppLinkConfigIgnoreMagicNumberMismatch 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.14 junienable read-only
The ignore magic number mismatch option of the PPP interface determines the action to be taken, when the peer has not negotiated any value yet sent null or invalid magic number in the LCP echo packets. The two actions that can be configured are: 1) Ignore the mismatch and retain connection 2) Disallow the mismatch and terminate connection
                       juniPppLinkConfigMaxLcpRenegotiation 1.3.6.1.4.1.4874.2.2.11.1.1.2.1.15 integer32 read-only
Maximum number of allowed lcp renegotiation attempts from peer.
               juniPppNextIfIndex 1.3.6.1.4.1.4874.2.2.11.1.1.3 juninextifindex read-only
Coordinate ifIndex value allocation for entries in the juniPppLinkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
           juniPppSec 1.3.6.1.4.1.4874.2.2.11.1.2
           juniPppIp 1.3.6.1.4.1.4874.2.2.11.1.3
               juniPppIpTable 1.3.6.1.4.1.4874.2.2.11.1.3.1 no-access
Table containing the IP parameters for the local PPP entity.
                   juniPppIpEntry 1.3.6.1.4.1.4874.2.2.11.1.3.1.1 no-access
IPCP status information for a particular PPP link.
                       juniPppIpServiceStatus 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.1 junienable read-only
Indicates whether IP protocol service is operating over this PPP link. Service is established on this link through means outside this MIB.
                       juniPppIpTerminateReason 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.2 integer read-only
Reason the IPCP link was terminated: none None. other Not specified. noService No IP service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPCP option. See juniPppIpTerminateNegFailOption. Enumeration: 'none': 0, 'peerRenegotiated': 6, 'admin': 3, 'linkDown': 4, 'noService': 2, 'peerTerminated': 5, 'other': 1, 'negotiationFailure': 8, 'maxRetriesExceeded': 7.
                       juniPppIpTerminateNegFailOption 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.3 integer read-only
Reports the PPP IPCP option for which negotiation failed, when juniPppIpTerminateReason has the value 'negotiationFailure'. Enumeration: 'remotePrimaryDnsAddress': 4, 'none': 0, 'localIpAddressMask': 8, 'remoteIpAddressMask': 9, 'localIpAddress': 2, 'other': 1, 'remoteSecondaryWinsAddress': 7, 'remotePrimaryWinsAddress': 6, 'remoteIpAddress': 3, 'remoteSecondaryDnsAddress': 5.
                       juniPppIpLocalIpAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.4 ipaddress read-only
IP Address used by the local side.
                       juniPppIpRemoteIpAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.5 ipaddress read-only
IP Address used by the remote side.
                       juniPppIpRemotePrimaryDnsAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.6 ipaddress read-only
Primary DNS server used by the remote side.
                       juniPppIpRemoteSecondaryDnsAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.7 ipaddress read-only
Secondary DNS server used by the remote side.
                       juniPppIpRemotePrimaryWinsAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.8 ipaddress read-only
Primary WINS server used by the remote side.
                       juniPppIpRemoteSecondaryWinsAddress 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.9 ipaddress read-only
Secondary WINS server used by the remote side.
                       juniPppIpNetworkStatusIpcpRenegoTerminates 1.3.6.1.4.1.4874.2.2.11.1.3.1.1.10 counter32 read-only
Number of times ipcp terminated due to peer exceeding max renegotiation attempts.
               juniPppIpConfigTable 1.3.6.1.4.1.4874.2.2.11.1.3.2 no-access
Table containing the IP parameters for the local PPP entity.
                   juniPppIpConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.3.2.1 no-access
IPCP configuration information for a particular PPP link.
                       juniPppIpConfigPeerDnsPriority 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.1 junienable read-write
When enabled, allows peer's DNS address to prevail in the event of a negotiation conflict; when disabled, the local PPP interface's DNS address prevails.
                       juniPppIpConfigPeerWinsPriority 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.2 junienable read-write
When enabled, allows peer's WINS address to prevail in the event of a negotiation conflict; when disabled, the local PPP interface's WINS address prevails.
                       juniPppIpConfigIpcpNetmask 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.3 junienable read-write
Enables the negotiation of the IPCP option netmask (0x90) during IPCP negotiation.
                       juniPppIpConfigInitiateIp 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.4 junienable read-write
Enables the initiation of negotiation of the IPCP.
                       juniPppIpConfigMaxIpcpRenegotiation 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.5 integer32 read-write
Maximum number of allowed ipcp renegotiation attempts from peer.
                       juniPppIpConfigPromptIpcpDnsOption 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.6 junienable read-write
Control prompting of IPCP DNS option to remote peer.
                       juniPppIpConfigIpcpLockout 1.3.6.1.4.1.4874.2.2.11.1.3.2.1.7 junienable read-write
Enables IPCP lockout. It determines whether this NCP can be negotiated when the interface is already running a different NCP. On enabling this option, the IPCP negotiation will be blocked after a different NCP service is up and waited for 10 seconds for IPCP initiation from peer.
           juniPppOsi 1.3.6.1.4.1.4874.2.2.11.1.4
               juniPppOsiTable 1.3.6.1.4.1.4874.2.2.11.1.4.1 no-access
Table containing the OSI parameters for the local PPP entity.
                   juniPppOsiEntry 1.3.6.1.4.1.4874.2.2.11.1.4.1.1 no-access
OSICP status information for a particular PPP link.
                       juniPppOsiServiceStatus 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.1 junienable read-only
Indicates whether OSI protocol service is operating over this PPP link. Service is established on this link through means outside this MIB.
                       juniPppOsiOperStatus 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.2 integer read-only
The operational status of the OSI network protocol. If the value of this object is up then the finite state machine for the OSI network protocol has reached the Opened state. Enumeration: 'opened': 1, 'notOpened': 2.
                       juniPppOsiTerminateReason 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.3 integer read-only
Reason the OSICP link was terminated: none None. other Not specified. noService No OSI service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPCP option. See juniPppOsiTerminateNegFailOption. Enumeration: 'none': 0, 'peerRenegotiated': 6, 'admin': 3, 'linkDown': 4, 'noService': 2, 'peerTerminated': 5, 'other': 1, 'negotiationFailure': 8, 'maxRetriesExceeded': 7.
                       juniPppOsiTerminateNegFailOption 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.4 integer read-only
Reports the PPP OSICP option for which negotiation failed, when juniPppOsiTerminateReason has the value 'negotiationFailure'. Enumeration: 'none': 0, 'other': 1, 'localAlignNpd': 2, 'remoteAlignNpd': 3.
                       juniPppOsiLocalAlignNpdu 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.5 integer read-only
Local alignment of network PDU: none No alignment specified. oneModulo4 Alignment on first octet (out of four). twoModulo4 Alignment on second octet (out of four). threeModulo4 Alignment on third octet (out of four). fourModulo4 Alignment on fourth octet (out of four). even Alignment on even-octet boundary. odd Alignment on odd-octet boundary. Enumeration: 'even': 254, 'none': 0, 'oneModulo4': 1, 'twoModulo4': 2, 'threeModulo4': 3, 'fourModulo4': 4, 'odd': 255.
                       juniPppOsiRemoteAlignNpdu 1.3.6.1.4.1.4874.2.2.11.1.4.1.1.6 integer read-only
Remote alignment of network PDU. none No alignment specified. oneModulo4 Alignment on first octet (out of four). twoModulo4 Alignment on second octet (out of four). threeModulo4 Alignment on third octet (out of four). fourModulo4 Alignment on fourth octet (out of four). even Alignment on even-octet boundary. odd Alignment on odd-octet boundary. Enumeration: 'even': 254, 'none': 0, 'oneModulo4': 1, 'twoModulo4': 2, 'threeModulo4': 3, 'fourModulo4': 4, 'odd': 255.
               juniPppOsiConfigTable 1.3.6.1.4.1.4874.2.2.11.1.4.2 no-access
Table containing configuration variables for the OSICP for the local PPP entity.
                   juniPppOsiConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.4.2.1 no-access
OSICP information for a particular PPP link.
                       juniPppOsiConfigAdminStatus 1.3.6.1.4.1.4874.2.2.11.1.4.2.1.1 integer read-write
The immediate desired status of the OSI network protocol. Setting this object to open will inject an administrative open event into the OSI network protocol's finite state machine. Setting this object to close will inject an administrative close event into the OSI network protocol's finite state machine. Enumeration: 'close': 2, 'open': 1.
           juniPppSession 1.3.6.1.4.1.4874.2.2.11.1.5
               juniPppSessionTable 1.3.6.1.4.1.4874.2.2.11.1.5.1 no-access
This table contains entries for PPP interfaces present in the system.
                   juniPppSessionEntry 1.3.6.1.4.1.4874.2.2.11.1.5.1.1 no-access
Each entry describes the characteristics of a PPP interface.
                       juniPppSessionGrant 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.1 truthvalue read-only
Indicates whether a session has been granted via the authentication mechanism.
                       juniPppSessionTerminateReason 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.2 integer read-only
The reason the session was terminated. Enumeration: 'keepaliveFailure': 3, 'none': 0, 'noResources': 11, 'lowerLayerDown': 7, 'addressLeaseExpired': 16, 'unknown': 1, 'requestTimeout': 14, 'noHardware': 10, 'deny': 9, 'challengeTimeout': 13, 'noInterface': 12, 'inactivityTimeout': 5, 'sessionTimeout': 4, 'tunnelFailed': 18, 'adminLogout': 17, 'adminDisable': 6, 'noUpperInterface': 8, 'authenticatorTimeout': 15, 'userRequest': 2.
                       juniPppSessionStartTime 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.3 timeticks read-only
The value of sysUpTime when this session last became active.
                       juniPppSessionInOctets 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.4 counter32 read-only
Number of octets received since this session last became active, as denoted by juniPppSessionStartTime.
                       juniPppSessionOutOctets 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.5 counter32 read-only
Number of octets sent since this session last became active, as denoted by juniPppSessionStartTime.
                       juniPppSessionInPackets 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.6 counter32 read-only
Number of packets received since this session last became active, as denoted by juniPppSessionStartTime.
                       juniPppSessionOutPackets 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.7 counter32 read-only
Number of packets sent since this session last became active, as denoted by juniPppSessionStartTime.
                       juniPppSessionSessionTimeout 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.8 integer32 read-only
Maximum duration for the session, after which the session terminates automatically.
                       juniPppSessionInactivityTimeout 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.9 integer32 read-only
Maximum inactivity duration for the session, after which the session terminates automatically.
                       juniPppSessionAccountingInterval 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.10 integer32 read-only
Interval that must elapse between generation of accounting records for this session.
                       juniPppSessionRemoteIpAddress 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.11 ipaddress read-only
Remote IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionRemotePrimaryDnsAddress 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.12 ipaddress read-only
Remote primary DNS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionRemoteSecondaryDnsAddress 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.13 ipaddress read-only
Remote secondary DNS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionRemotePrimaryWinsAddress 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.14 ipaddress read-only
Remote primary WINS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionRemoteSecondaryWinsAddress 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.15 ipaddress read-only
Remote secondary WINS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionRemoteIpv6AddressIfIdentifier 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.16 ipv6addressifidentifier read-only
IPV6 Address Interface Identifier obtained from the authentication service, to be used during IPCP negotiation with the remote side.
                       juniPppSessionInhibitIp 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.17 truthvalue read-only
Indicates whether a session has had its IP service inhibited by the authentication mechanism.
                       juniPppSessionInhibitIpv6 1.3.6.1.4.1.4874.2.2.11.1.5.1.1.18 truthvalue read-only
Indicates whether a session has had its IPv6 service inhibited by the authentication mechanism.
           juniPppMlPpp 1.3.6.1.4.1.4874.2.2.11.1.6
               juniPppMlPppBundleTable 1.3.6.1.4.1.4874.2.2.11.1.6.1 no-access
This table contains entries for MLPPP bundles present in the system.
                   juniPppMlPppBundleEntry 1.3.6.1.4.1.4874.2.2.11.1.6.1.1 no-access
Each entry describes the characteristics of a MLPPP bundle.
                       juniPppMlPppBundleName 1.3.6.1.4.1.4874.2.2.11.1.6.1.1.1 junipppmlpppbundlename no-access
The administrative name of the MLPPP bundle associated with this MLPPP network interface.
                       juniPppMlPppBundleRowStatus 1.3.6.1.4.1.4874.2.2.11.1.6.1.1.2 rowstatus read-only
The rowStatus for this entry. The following sets are supported: createAndGo(4), destroy(6) The following values can be read from this object: active(1)
                       juniPppMlPppBundleNetworkIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.1.1.3 interfaceindex read-only
The ifIndex of this MLPPP network interface. It is a valid ifIndex even if there is no corresponding network interface instance in the juniPppMlPppLinkConfigTable.
               juniPppMlPppNextLinkIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.2 juninextifindex read-only
Coordinate ifIndex value allocation for entries in juniPppMlPppLinkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
               juniPppMlPppLinkConfigTable 1.3.6.1.4.1.4874.2.2.11.1.6.3 no-access
This table contains entries for MLPPP interfaces present in the system.
                   juniPppMlPppLinkConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.6.3.1 no-access
Each entry describes the characteristics of MLPPP interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
                       juniPppMlPppLinkConfigIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.1 interfaceindex no-access
The ifIndex of the MLPPP interface. When creating entries in this table, suitable values for this object are determined by reading juniPppMlPppNextLinkIfIndex.
                       juniPppMlPppLinkConfigLowerIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.2 interfaceindexorzero read-only
The ifIndex of an interface over which this PPP interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a non-zero value be configured at entry creation.
                       juniPppMlPppLinkConfigKeepalive 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.4 integer32 read-only
Keepalive interval in seconds. A value of zero disables keepalive. Keepalive is performed using LCP Echo.
                       juniPppMlPppLinkConfigAuthentication 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.5 junipppauthentication read-only
Specifies the type(s) of authentication, if any, to be negotiated with the peer: none No authentication is negotiated. pap PAP negotiation only. chap CHAP negotiation only. papChap PAP negotiation is attempted first; if fails, attempt CHAP. chapPap CHAP negotiation is attempted first; if fails, attempt PAP. If authentication negotiation is not supported for this MLPPP interface, then any attempt to explicitely set this object will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation. Setting this object to none(0) will set juniPppMlPppLinkConfigAuthenticatorVirtualRouter object to an empty string. This object returns a none (0) value on the get operation. New object juniPppMlPppLinkConfigAuthentication2 will reflect the configured values. Setting this object along with the juniPppMlPppLinkConfigAuthentication2 object will return an inconsistentValue error.
                       juniPppMlPppLinkConfigMaxAuthenRetries 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.6 integer32 read-only
The number of authentication retries permitted, in addition to a failed initial attempt. If all retries fail, the link is reset.
                       juniPppMlPppLinkConfigRowStatus 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.7 rowstatus read-only
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniPppMlPppLinkConfigRowStatus juniPppMlPppLinkConfigLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniPppMlPppLinkConfigIndex must have been determined previously, by reading juniPppMlPppNextIfIndex. The interface identified by juniPppMlPppLinkConfigLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
                       juniPppMlPppLinkConfigAaaProfile 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.8 juniname read-only
The name of the AAA profile to be used for authentication on the PPP interface. Setting this object statically binds the AAA profile with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored. On a Set operation, if the value of this object is not null and does not correspond to an existing AAA profile, then an inconsistentValue error is returned.
                       juniPppMlPppLinkConfigChapMinChallengeLength 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.9 integer32 read-only
Minimum value of the CHAP authenticator challenge length value. This value is never allowed to be set to a value greater than juniPppMlPppLinkConfigChapMaxChallengeLength.
                       juniPppMlPppLinkConfigChapMaxChallengeLength 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.10 integer32 read-only
Maximum value of the CHAP authenticator challenge length value.
                       juniPppMlPppLinkConfigPassiveMode 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.11 junienable read-only
When enabled, LCP state machine is forced into passive mode on lower layer UP message. It adds compatibility with slow and buggy clients.
                       juniPppMlPppLinkConfigAuthenticatorVirtualRouter 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.12 juniname read-only
The name of the virtual router (Juniper-ROUTER-MIB.juniRouterName) to be used for authentication on the PPP interface. Setting this object statically binds the authenticating virtual router with the link interface. If this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned.
                       juniPppMlPppLinkConfigFragmentation 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.13 junienable read-only
Enables MLPPP fragmentation. Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigReassembly 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.14 junienable read-only
Enables MLPPP reassembly. Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigMaxReceiveReconstructedUnit 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.15 integer32 read-only
The Maximum Receive Reconstructed Unit (MRRU) that the local PPP entity will advertise to the remote entity. If the value of this variable is 1, then the MRRU is set to the local MRU value. Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigFragmentSize 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.16 integer32 read-only
The size of fragments transmitted by the local PPP entity. If the value of this variable is 1, then the fragment size is set to the link's MTU value. Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigHashLinkSelection 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.17 junienable read-only
Enables MLPPP hash-based link selection for non-best-effort traffic. Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigAuthentication2 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.18 juninibbleconfig read-only
A configuration variable comprised of nibbles i.e. 4 bits, such that a client can supply a list of 0 to 8 selections. The least significant nibble is the first value of the list, and the most significant nibble is the last value. The value in each field ranges from 0 to 15, however the first nibble with value 0 indicates the end of the list. Repetition of values is not allowed. Segregation of values is not allowed. Valid Values are: none - 0 pap - 1 chap - 2 eap - 3 Example valid encoding: 0x00000321 0x00000012 Not a valid encoding: 0x00000121 0x01002001 If authentication negotiation is not supported for this PPP interface, then any attempt to explicitly set this object will result in a notWritable error and it will be implicitly set to the DEFVAL on row creation. Setting this object to null will set juniPppMlPppLinkConfigAuthenticatorVirtualRouter object to an empty string. Setting this object along with the juniPppMlPppLinkConfigAuthentication object will return an inconsistentValue error.
                       juniPppMlPppLinkConfigIgnoreMagicNumberMismatch 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.19 junienable read-only
The ignore magic number mismatch option of the PPP interface determines the action to be taken, when the peer has not negotiated any value yet sent null or invalid magic number in the LCP echo packets. The two actions that can be configured are: 1) Ignore the mismatch and retain connection 2) Disallow the mismatch and terminate connection
                       juniPppMlPppLinkConfigMultilinkMulticlass 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.20 junienable read-only
Enables Multiclass Multilink PPP (MCML). Changing this object has an effect when the link is next restarted.
                       juniPppMlPppLinkConfigMultilinkMaxMultiClasses 1.3.6.1.4.1.4874.2.2.11.1.6.3.1.21 integer read-only
Maximum number of MCML classes to be negotiated. Changing this object has an effect when the link is next restarted.
               juniPppMlPppNextNetworkIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.4 juninextifindex read-only
Coordinate ifIndex value allocation for entries in juniPppMlPppNetworkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
               juniPppMlPppNetworkConfigTable 1.3.6.1.4.1.4874.2.2.11.1.6.5 no-access
This table contains entries for MLPPP network interfaces present in the system.
                   juniPppMlPppNetworkConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.6.5.1 no-access
Each entry describes the characteristics of MLPPP interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
                       juniPppMlPppNetworkConfigIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.5.1.1 interfaceindex no-access
The ifIndex of the MLPPP network interface. When creating entries in this table, suitable values for this object are determined by reading juniPppMlPppNextNetworkIfIndex.
                       juniPppMlPppNetworkConfigLowerIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.5.1.2 interfaceindex read-only
The ifIndex of a PPP link interface over which this PPP network interface is to be layered. On sets, the value of this object must equal on of the previously created PPP link interfaces created in the juniPppMlPppLinkConfigTable. On gets, the value of this object is the lexicographically least PPP link interface in a potential bundle of PPP link interfaces.
                       juniPppMlPppNetworkBundleName 1.3.6.1.4.1.4874.2.2.11.1.6.5.1.3 junipppmlpppbundlename read-only
The MLPPP bundle name administratively assigned.
                       juniPppMlPppNetworkRowStatus 1.3.6.1.4.1.4874.2.2.11.1.6.5.1.4 rowstatus read-only
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniPppMlPppNetworkConfigLowerIfIndex juniPppMlPppNetworkBundleName juniPppMlPppNetworkConfigRowStatus In addition, when creating an entry the following conditions must hold: A value for juniPppMlPppNetworkConfigIndex must have been determined previously, by reading juniPppMlPppNextNetworkIfIndex. The interface identified by juniPppMlPppNetworkConfigLowerIfIndex must exist by a creation request to the juniPppMlPppLinkConfigTable. The bundleName specified in juniPppMlPppNetworkBundleName must have been created first in the juniPppMlPppBundleTable. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
               juniPppMlPppLinkBindTable 1.3.6.1.4.1.4874.2.2.11.1.6.6 no-access
This table contains entries for MLPPP Link interface to MLPPP network interfaces bindings.
                   juniPppMlPppLinkBindEntry 1.3.6.1.4.1.4874.2.2.11.1.6.6.1 no-access
Each entry describes the MLPPP link interface to MLPPP network interface bindings.
                       juniPppMlPppBindNetworkIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.6.1.1 interfaceindex no-access
The ifIndex of the MLPPP network interface.
                       juniPppMlPppBindLinkIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.6.1.2 interfaceindex no-access
The ifIndex of a MLPPP link interface bound by the MLPPP network interface defined by juniPppMlPppBindNetworkIfIndex.
                       juniPppMlPppBindRowStatus 1.3.6.1.4.1.4874.2.2.11.1.6.6.1.3 rowstatus read-only
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniPppMlPppBindRowStatus In addition, when creating an entry the following conditions must hold: The interfaces identified by juniPppMlPppBindNetworkIfIndex and juniPppMlPppBindLinkIfIndex must be created in the juniPppMlPppNetworkConfigTable and juniPppMlPppLinkConfigTable respectively. A MLPPP bundle must be associated with the juniPppMlPppNetworkIfIndex and exist in the juniPppMibPppBundleTable. A corresponding entry in ifStackTable is created/destroyed as a result of creating/destroying an entry in this table.
               juniPppMlPppMulticlassTraffiClassTable 1.3.6.1.4.1.4874.2.2.11.1.6.7 no-access
This table contains entries for MLPPP Multiclass to traffic class mapping of interfaces present in the system.
                   juniPppMlPppMulticlassTrafficClassEntry 1.3.6.1.4.1.4874.2.2.11.1.6.7.1 no-access
Each entry describes the MLPPP multiclass to traffic class mapping of interfaces.Other characteristics like fragmentation and reassembly for a particular traffic class can be configured.
                       juniPppMlPppMulticlassIfIndex 1.3.6.1.4.1.4874.2.2.11.1.6.7.1.1 interfaceindex no-access
The ifIndex of the MLPPP interface. When creating entries in this table, suitable values for this object are determined by reading juniPppMlPppMulticlassIfIndex.
                       juniPppMlPppMulticlassIndex 1.3.6.1.4.1.4874.2.2.11.1.6.7.1.2 integer no-access
The multiclass index of a particular traffic class type. This can be configured only when MCMP is enabled on the link interface.
                       juniPppMlPppMulticlassTcName 1.3.6.1.4.1.4874.2.2.11.1.6.7.1.3 junipppmlpppmulticlasstcname read-write
The traffic class index mapped to the MCMP multiclass index. This can be configured only when MCMP is enabled on the link interface.
                       juniPppMlPppMulticlassFragmentation 1.3.6.1.4.1.4874.2.2.11.1.6.7.1.4 junienable read-write
Enable or disable fragmentation for a particular multiclass. This can be configured only when MCMP is enaled on the link interface.
                       juniPppMlPppMulticlassReassembly 1.3.6.1.4.1.4874.2.2.11.1.6.7.1.5 junienable read-write
Enable or disable rassembly for a particular multiclass. This can be configured only when MCMP is enaled on the link interface.
           juniPppSummary 1.3.6.1.4.1.4874.2.2.11.1.7
               juniPppSummaryPppInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.1 integer32 read-only
The total number of PPP interfaces configured in the system.
               juniPppSummaryPppIpNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.2 integer32 read-only
The total number IP NCPs configured in the system.
               juniPppSummaryPppOsiNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.3 integer32 read-only
The total number of OSI NCPs configured in the system.
               juniPppSummaryPppIfAdminUp 1.3.6.1.4.1.4874.2.2.11.1.7.4 integer32 read-only
The total number of PPP interfaces in the system that are administratively configured to up(1).
               juniPppSummaryPppIfAdminDown 1.3.6.1.4.1.4874.2.2.11.1.7.5 integer32 read-only
The total number of PPP interfaces in the system that are administrateively configued to down(2).
               juniPppSummaryPppIfOperUp 1.3.6.1.4.1.4874.2.2.11.1.7.7 integer32 read-only
The total number of PPP interfaces in the system with an operational state of up(1).
               juniPppSummaryPppIfOperDown 1.3.6.1.4.1.4874.2.2.11.1.7.8 integer32 read-only
The total number of PPP interfaces in the system with an operational state of down(2).
               juniPppSummaryPppIfOperDormant 1.3.6.1.4.1.4874.2.2.11.1.7.9 integer32 read-only
The total number of PPP interfaces in the system with an operational state of dormant(5).
               juniPppSummaryPppIfNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.10 integer32 read-only
The total number of PPP interfaces in the system with an operational state of notPresent(6).
               juniPppSummaryPppIfLowerLayerDown 1.3.6.1.4.1.4874.2.2.11.1.7.11 integer32 read-only
The total number of PPP interfaces in the system with an operational state of lowerLayerDown(7).
               juniPppSummaryPppIpNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.12 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of opened(1).
               juniPppSummaryPppIpNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.13 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of not-opened(2).
               juniPppSummaryPppOsiNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.14 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of opened.
               juniPppSummaryPppOsiNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.15 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of closed.
               juniPppSummaryPppIfLastChangeTime 1.3.6.1.4.1.4874.2.2.11.1.7.16 timeticks read-only
The value of the sysUpTime at the time of the last PPP interface creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value.
               juniPppSummaryPppLinkInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.17 integer32 read-only
The total number of PPP Link interfaces configured in the system.
               juniPppSummaryPppLinkIfAdminUp 1.3.6.1.4.1.4874.2.2.11.1.7.18 integer32 read-only
The total number of PPP Link interfaces in the system that are administratively configured to up(1).
               juniPppSummaryPppLinkIfAdminDown 1.3.6.1.4.1.4874.2.2.11.1.7.19 integer32 read-only
The total number of PPP Link interfaces in the system that are administrateively configued to down(2).
               juniPppSummaryPppLinkIfOperUp 1.3.6.1.4.1.4874.2.2.11.1.7.20 integer32 read-only
The total number of PPP Link interfaces in the system with an operational state of up(1).
               juniPppSummaryPppLinkIfOperDown 1.3.6.1.4.1.4874.2.2.11.1.7.21 integer32 read-only
The total number of PPP Link interfaces in the system with an operational state of down(2).
               juniPppSummaryPppLinkIfOperDormant 1.3.6.1.4.1.4874.2.2.11.1.7.22 integer32 read-only
The total number of PPP Link interfaces in the system with an operational state of dormant(5).
               juniPppSummaryPppLinkIfNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.23 integer32 read-only
The total number of PPP link interfaces in the system with an operational state of notPresent(6).
               juniPppSummaryPppLinkIfLowerLayerDown 1.3.6.1.4.1.4874.2.2.11.1.7.24 integer32 read-only
The total number of PPP Link interfaces in the system with an operational state of lowerLayerDown(7).
               juniPppSummaryPppLinkIfLastChangeTime 1.3.6.1.4.1.4874.2.2.11.1.7.25 timeticks read-only
The value of the sysUpTime at the time of the last PPP Link interface creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value.
               juniPppSummaryPppNetworkInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.26 integer32 read-only
The total number of PPP network interfaces configured in the system.
               juniPppSummaryPppNetworkIpNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.27 integer32 read-only
The total number IP NCPs in the system configured on PPP network interfaces.
               juniPppSummaryPppNetworkOsiNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.28 integer32 read-only
The total number of OSI NCPs in the system configured on PPP network interfaces.
               juniPppSummaryPppNetworkIfAdminUp 1.3.6.1.4.1.4874.2.2.11.1.7.29 integer32 read-only
The total number of PPP network interfaces in the system that are administratively configured to up(1).
               juniPppSummaryPppNetworkIfAdminDown 1.3.6.1.4.1.4874.2.2.11.1.7.30 integer32 read-only
The total number of PPP network interfaces in the system that are administrateively configued to down(2).
               juniPppSummaryPppNetworkIfOperUp 1.3.6.1.4.1.4874.2.2.11.1.7.31 integer32 read-only
The total number of PPP network interfaces in the system with an operational state of up(1).
               juniPppSummaryPppNetworkIfOperDown 1.3.6.1.4.1.4874.2.2.11.1.7.32 integer32 read-only
The total number of PPP network interfaces in the system with an operational state of down(2).
               juniPppSummaryPppNetworkIfOperDormant 1.3.6.1.4.1.4874.2.2.11.1.7.33 integer32 read-only
The total number of PPP network interfaces in the system with an operational state of dormant(5).
               juniPppSummaryPppNetworkIfNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.34 integer32 read-only
The total number of PPP network interfaces in the system with an operational state of notPresent(6).
               juniPppSummaryPppNetworkIfLowerLayerDown 1.3.6.1.4.1.4874.2.2.11.1.7.35 integer32 read-only
The total number of PPP network interfaces in the system with an operational state of lowerLayerDown(7).
               juniPppSummaryPppNetworkIpNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.36 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of opened(1).
               juniPppSummaryPppNetworkIpNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.37 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of not-opened(2).
               juniPppSummaryPppNetworkOsiNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.38 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of opened.
               juniPppSummaryPppNetworkOsiNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.39 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of closed.
               juniPppSummaryPppNetworkIfLastChangeTime 1.3.6.1.4.1.4874.2.2.11.1.7.40 timeticks read-only
The value of the sysUpTime at the time of the last PPP network interface creation or deletion in the system. If the number of PPP network interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value.
               juniPppSummaryPppIpv6NCPs 1.3.6.1.4.1.4874.2.2.11.1.7.41 integer32 read-only
The total number IPv6 NCPs configured in the system.
               juniPppSummaryPppIpv6NcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.42 integer32 read-only
The total number of PPP IPv6 NCPs in the system with an operational state of opened(1).
               juniPppSummaryPppIpv6NcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.43 integer32 read-only
The total number of PPP IPv6 NCPs in the system with an operational state of not-opened(2).
               juniPppSummaryPppNetworkIpv6NCPs 1.3.6.1.4.1.4874.2.2.11.1.7.44 integer32 read-only
The total number IPv6 NCPs configured in the system.
               juniPppSummaryPppNetworkIpv6NcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.45 integer32 read-only
The total number of PPP IPv6 NCPs in the system with an operational state of opened(1).
               juniPppSummaryPppNetworkIpv6NcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.46 integer32 read-only
The total number of PPP IPv6 NCPs in the system with an operational state of not-opened(2).
               juniPppSummaryPppStaticInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.47 integer32 read-only
The total number of static PPP interfaces configured in the system.
               juniPppSummaryPppMplsNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.48 integer32 read-only
The total number MPLS NCPs configured in the system.
               juniPppSummaryPppIpAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.49 integer32 read-only
The total number of IP NCPs in the system that are administratively configured to open(1).
               juniPppSummaryPppIpAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.50 integer32 read-only
The total number of IP NCPs in the system that are administratively configured to close(2).
               juniPppSummaryPppIpv6AdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.51 integer32 read-only
The total number of IPV6 NCPs in the system that are administratively configured to open(1).
               juniPppSummaryPppIpv6AdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.52 integer32 read-only
The total number of IPV6 NCPs in the system that are administratively configured to close(2).
               juniPppSummaryPppOsiAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.53 integer32 read-only
The total number of OSI NCPs in the system that are administratively configured to open(1).
               juniPppSummaryPppOsiAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.54 integer32 read-only
The total number of OSI NCPs in the system that are administratively configured to close(2).
               juniPppSummaryPppMplsAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.55 integer32 read-only
The total number of MPLS NCPs in the system that are administratively configured to open(1).
               juniPppSummaryPppMplsAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.56 integer32 read-only
The total number of MPLS NCPs in the system that are administratively configured to close(2).
               juniPppSummaryPppIpNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.57 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of notPresent(3).
               juniPppSummaryPppIpNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.58 integer32 read-only
The total number of PPP IP NCPs in the system with an operational state of noResources(4).
               juniPppSummaryPppIpv6NcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.59 integer32 read-only
The total number of PPP IPV6 NCPs in the system with an operational state of notPresent(3).
               juniPppSummaryPppIpv6NcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.60 integer32 read-only
The total number of PPP IPV6 NCPs in the system with an operational state of noResources(4).
               juniPppSummaryPppOsiNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.61 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of notPresent(3).
               juniPppSummaryPppOsiNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.62 integer32 read-only
The total number of PPP OSI NCPs in the system with an operational state of noResources(4).
               juniPppSummaryPppMplsNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.63 integer32 read-only
The total number of PPP MPLS NCPs in the system with an operational state of opened(1).
               juniPppSummaryPppMplsNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.64 integer32 read-only
The total number of PPP MPLS NCPs in the system with an operational state of not-opened(2).
               juniPppSummaryPppMplsNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.65 integer32 read-only
The total number of PPP MPLS NCPs in the system with an operational state of notPresent(3).
               juniPppSummaryPppMplsNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.66 integer32 read-only
The total number of PPP MPLS NCPs in the system with an operational state of noResources(4).
               juniPppSummaryPppLinkStaticInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.67 integer32 read-only
The total number of static PPP Link interfaces configured in the system.
               juniPppSummaryPppNetworkStaticInterfaceCount 1.3.6.1.4.1.4874.2.2.11.1.7.68 integer32 read-only
The total number of static PPP network interfaces configured in the system.
               juniPppSummaryPppNetworkMplsNCPs 1.3.6.1.4.1.4874.2.2.11.1.7.69 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces.
               juniPppSummaryPppNetworkIpAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.70 integer32 read-only
The total number of IP NCPs in the system configured on PPP network interfaces that are administratively configured to open(1).
               juniPppSummaryPppNetworkIpAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.71 integer32 read-only
The total number of IP NCPs in the system configured on PPP network interfaces that are administratively configured to close(2).
               juniPppSummaryPppNetworkIpv6AdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.72 integer32 read-only
The total number of IPV6 NCPs in the system configured on PPP network interfaces that are administratively configured to open(1).
               juniPppSummaryPppNetworkIpv6AdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.73 integer32 read-only
The total number of IPV6 NCPs in the system configured on PPP network interfaces that are administratively configured to close(2).
               juniPppSummaryPppNetworkOsiAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.74 integer32 read-only
The total number of OSI NCPs in the system configured on PPP network interfaces that are administratively configured to open(1).
               juniPppSummaryPppNetworkOsiAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.75 integer32 read-only
The total number of OSI NCPs in the system configured on PPP network interfaces that are administratively configured to close(2).
               juniPppSummaryPppNetworkMplsAdminOpen 1.3.6.1.4.1.4874.2.2.11.1.7.76 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces that are administratively configured to open(1).
               juniPppSummaryPppNetworkMplsAdminClose 1.3.6.1.4.1.4874.2.2.11.1.7.77 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces that are administratively configured to close(2).
               juniPppSummaryPppNetworkIpNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.78 integer32 read-only
The total number of IP NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3).
               juniPppSummaryPppNetworkIpNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.79 integer32 read-only
The total number of IP NCPs in the system configured on PPP network interfaces with an operational state of noResources(4).
               juniPppSummaryPppNetworkIpv6NcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.80 integer32 read-only
The total number of IPV6 NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3).
               juniPppSummaryPppNetworkIpv6NcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.81 integer32 read-only
The total number of IPV6 NCPs in the system configured on PPP network interfaces with an operational state of noResources(4).
               juniPppSummaryPppNetworkOsiNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.82 integer32 read-only
The total number of OSI NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3).
               juniPppSummaryPppNetworkOsiNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.83 integer32 read-only
The total number of OSI NCPs in the system configured on PPP network interfaces with an operational state of noResources(4).
               juniPppSummaryPppNetworkMplsNcpOpened 1.3.6.1.4.1.4874.2.2.11.1.7.84 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of opened(1).
               juniPppSummaryPppNetworkMplsNcpClosed 1.3.6.1.4.1.4874.2.2.11.1.7.85 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of not-opened(2).
               juniPppSummaryPppNetworkMplsNcpNotPresent 1.3.6.1.4.1.4874.2.2.11.1.7.86 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3).
               juniPppSummaryPppNetworkMplsNcpNoResources 1.3.6.1.4.1.4874.2.2.11.1.7.87 integer32 read-only
The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of noResources(4).
           juniPppIpv6 1.3.6.1.4.1.4874.2.2.11.1.8
               juniPppIpv6Table 1.3.6.1.4.1.4874.2.2.11.1.8.1 no-access
Table containing the IPv6 parameters for the local PPP entity.
                   juniPppIpv6Entry 1.3.6.1.4.1.4874.2.2.11.1.8.1.1 no-access
IPV6CP status information for a particular PPP link.
                       juniPppIpv6ServiceStatus 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.1 junienable read-only
Indicates whether IPv6 protocol service is operating over this PPP link. Service is established on this link through means outside this MIB.
                       juniPppIpv6OperStatus 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.2 integer read-only
The operational status of the IPv6 network protocol. If the value of this object is up then the finite state machine for the IPv6 network protocol has reached the Opened state. Enumeration: 'opened': 1, 'notOpened': 2.
                       juniPppIpv6TerminateReason 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.3 integer read-only
Reason the IPV6CP link was terminated: none None. other Not specified. noService No IPv6 service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPV6CP option. See juniPppIpv6TerminateNegFailOption. Enumeration: 'none': 0, 'peerRenegotiated': 6, 'admin': 3, 'linkDown': 4, 'noService': 2, 'peerTerminated': 5, 'other': 1, 'negotiationFailure': 8, 'maxRetriesExceeded': 7.
                       juniPppIpv6TerminateNegFailOption 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.4 integer read-only
Reports the PPP IPV6CP option for which negotiation failed, when juniPppIpv6TerminateReason has the value 'negotiationFailure'. Enumeration: 'none': 0, 'other': 1, 'localIpv6AddressIfIdentifier': 2, 'remoteIpv6AddressIfIdentifier': 3.
                       juniPppIpv6LocalIpv6AddressIfIdentifier 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.5 ipv6addressifidentifier read-only
IPv6 Address Interface Identifier used by the local side.
                       juniPppIpv6RemoteIpv6AddressIfIdentifier 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.6 ipv6addressifidentifier read-only
IPv6 Address Interface Identifier used by the remote side.
                       juniPppIpv6NetworkStatusIpv6cpRenegoTerminates 1.3.6.1.4.1.4874.2.2.11.1.8.1.1.7 counter32 read-only
Number of times ipv6cp terminated due to peer exceeding max renegotiation attempts.
               juniPppIpv6ConfigTable 1.3.6.1.4.1.4874.2.2.11.1.8.2 no-access
Table containing the IPv6 parameters for the local PPP entity.
                   juniPppIpv6ConfigEntry 1.3.6.1.4.1.4874.2.2.11.1.8.2.1 no-access
IPV6CP configuration information for a particular PPP link.
                       juniPppIpv6ConfigAdminStatus 1.3.6.1.4.1.4874.2.2.11.1.8.2.1.1 integer read-write
The immediate desired status of the IPv6 network protocol. Setting this object to open will inject an administrative open event into the IPv6 network protocol's finite state machine. Setting this object to close will inject an administrative close event into the IPv6 network protocol's finite state machine. Enumeration: 'close': 2, 'open': 1.
                       juniPppIpv6ConfigInitiateIpv6 1.3.6.1.4.1.4874.2.2.11.1.8.2.1.2 junienable read-write
Enables the initiation of negotiation of the IPv6CP.
                       juniPppIpv6ConfigMaxIpv6cpRenegotiation 1.3.6.1.4.1.4874.2.2.11.1.8.2.1.3 integer32 read-write
Maximum number of allowed ipv6cp renegotiation attempts from peer.
           juniPppGlobalConfig 1.3.6.1.4.1.4874.2.2.11.1.9
               juniPppPeerIpAddressOptional 1.3.6.1.4.1.4874.2.2.11.1.9.1 junienable read-write
This option is used to ignore the conflicts between ppp clients requested IP address and radius/local pool returned address in server during IPNCP negotiation. Enabling this will ensure the IPNCP negotiation to succeed even though the client does not include IP address option in the IPNCP configure request.
       juniPppConformance 1.3.6.1.4.1.4874.2.2.11.4
           juniPppCompliances 1.3.6.1.4.1.4874.2.2.11.4.1
               juniPppCompliance 1.3.6.1.4.1.4874.2.2.11.4.1.1
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when additional objects were added to the MIB.
               juniPppCompliance2 1.3.6.1.4.1.4874.2.2.11.4.1.2
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when the juniPppMlPppGroup and juniPppSummaryGroup objects were added.
               juniPppCompliance3 1.3.6.1.4.1.4874.2.2.11.4.1.3
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when the juniPppLinkConfigStandardIfIndex object was added to the MIB.
               juniPppCompliance4 1.3.6.1.4.1.4874.2.2.11.4.1.4
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when the juniPppMlPppGroup, juniPppSummaryLinkGroup and juniPppSummaryNetworkGroup were moved from the list of mandatory groups.
               juniPppCompliance5 1.3.6.1.4.1.4874.2.2.11.4.1.5
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when new IP, LCP and multi-link objects were added.
               juniPppCompliance6 1.3.6.1.4.1.4874.2.2.11.4.1.6
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when new juniPppLcpGroup and juniPppMlPppGroup objects were added.
               juniPppCompliance7 1.3.6.1.4.1.4874.2.2.11.4.1.7
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when more new multi-link objects were added.
               juniPppCompliance8 1.3.6.1.4.1.4874.2.2.11.4.1.8
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when IPv6 support was added.
               juniPppCompliance9 1.3.6.1.4.1.4874.2.2.11.4.1.9
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when more new multi-link objects were added.
               juniPppCompliance10 1.3.6.1.4.1.4874.2.2.11.4.1.10
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when more new juniPppSummary objects were added.
               juniPppCompliance11 1.3.6.1.4.1.4874.2.2.11.4.1.11
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when a new multi-link object was added.
               juniPppCompliance12 1.3.6.1.4.1.4874.2.2.11.4.1.12
Obsolete compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when more new juniPppLcpGroup and juniPppMlPppGroup objects were added.
               juniPppCompliance13 1.3.6.1.4.1.4874.2.2.11.4.1.13
The compliance statement for entities which implement the Juniper PPP MIB. This statement became obsolete when more new juniPppLcpGroup, juniPppIpGroup and juniPppIpv6Group objects were added.
               juniPppCompliance14 1.3.6.1.4.1.4874.2.2.11.4.1.14
The compliance statement for entities which implement the Juniper PPP MIB.
               juniPppCompliance15 1.3.6.1.4.1.4874.2.2.11.4.1.15
The compliance statement for entities which implement the Juniper PPP MIB. This statement was obsoleted when MCMP traffic class mapping was added. New group juniPppMlPppMulticlassTcGroup1 was added.
               juniPppCompliance16 1.3.6.1.4.1.4874.2.2.11.4.1.16
The compliance statement for entities which implement the Juniper PPP MIB. This statement was obsoleted when juniPppPeerIpAddressOptional was added.
               juniPppCompliance17 1.3.6.1.4.1.4874.2.2.11.4.1.17
The compliance statement for entities which implement the Juniper PPP MIB.
           juniPppGroups 1.3.6.1.4.1.4874.2.2.11.4.2
               juniPppLcpGroup 1.3.6.1.4.1.4874.2.2.11.4.2.1
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppIpGroup 1.3.6.1.4.1.4874.2.2.11.4.2.2
Obsolete collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppOsiGroup 1.3.6.1.4.1.4874.2.2.11.4.2.3
Obsolete collection of objects providing management of OSI network control protocol functionality (OSICP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppLcpGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.4
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when the juniPppLinkConfigStandardIfIndex object was added.
               juniPppIpGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.5
Obsolete collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppOsiGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.6
A collection of objects providing management of OSI network control protocol functionality (OSICP) of PPP interfaces in a Juniper product.
               juniPppSessionGroup 1.3.6.1.4.1.4874.2.2.11.4.2.7
Obsolete collection of objects providing management of PPP session functionality of PPP interfaces in a Juniper product. This group became obsolete when IPv6 support was added.
               juniPppMlPppGroup 1.3.6.1.4.1.4874.2.2.11.4.2.8
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppSummaryGroup 1.3.6.1.4.1.4874.2.2.11.4.2.9
Obsolete collection of objects providing PPP interface summary information in a Juniper product. This group became obsolete when it was divided into three groups so that the link and network object would not be manditory.
               juniPppLcpGroup3 1.3.6.1.4.1.4874.2.2.11.4.2.10
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppSummaryBasicGroup 1.3.6.1.4.1.4874.2.2.11.4.2.11
Obsolete collection of objects providing PPP interface basic summary information in a Juniper product. This group became obsolete when IPv6 support was added.
               juniPppSummaryLinkGroup 1.3.6.1.4.1.4874.2.2.11.4.2.12
Obsolete collection of objects providing PPP interface basic summary information in a Juniper product. This group became obsolete when new objects were added.
               juniPppSummaryNetworkGroup 1.3.6.1.4.1.4874.2.2.11.4.2.13
Obsolete collection of objects providing PPP interface network summary information in a Juniper product. This group became obsolete when IPv6 support was added.
               juniPppLcpGroup4 1.3.6.1.4.1.4874.2.2.11.4.2.14
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppIpGroup3 1.3.6.1.4.1.4874.2.2.11.4.2.15
Obsolete collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product. This group became obsolete when IPv6 support was added.
               juniPppMlPppGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.16
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppMlPppGroup3 1.3.6.1.4.1.4874.2.2.11.4.2.17
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppLcpGroup5 1.3.6.1.4.1.4874.2.2.11.4.2.18
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppMlPppGroup4 1.3.6.1.4.1.4874.2.2.11.4.2.19
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppSummaryBasicGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.20
Obsolete collection of objects providing PPP interface basic summary information in a Juniper product. This group became obsolete when new objects were added.
               juniPppSummaryNetworkGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.21
Obsolete collection of objects providing PPP interface basic summary information in a Juniper product. This group became obsolete when new objects were added.
               juniPppIpGroup4 1.3.6.1.4.1.4874.2.2.11.4.2.22
A collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added
               juniPppIpv6Group 1.3.6.1.4.1.4874.2.2.11.4.2.23
A collection of objects providing management of IPV6 network control protocol functionality (IPV6CP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppSessionGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.24
A collection of objects providing management of PPP session functionality of PPP interfaces in a Juniper product.
               juniPppMlPppGroup5 1.3.6.1.4.1.4874.2.2.11.4.2.25
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppSummaryBasicGroup3 1.3.6.1.4.1.4874.2.2.11.4.2.26
A collection of objects providing PPP interface basic summary information in a Juniper product.
               juniPppSummaryLinkGroup2 1.3.6.1.4.1.4874.2.2.11.4.2.27
A collection of objects providing PPP interface link summary information in a Juniper product.
               juniPppSummaryNetworkGroup3 1.3.6.1.4.1.4874.2.2.11.4.2.28
A collection of objects providing PPP interface network summary information in a Juniper product.
               juniPppMlPppGroup6 1.3.6.1.4.1.4874.2.2.11.4.2.29
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added.
               juniPppLcpGroup6 1.3.6.1.4.1.4874.2.2.11.4.2.30
Obsolete collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppMlPppGroup7 1.3.6.1.4.1.4874.2.2.11.4.2.31
Obsolete collection of objects providing multi link PPP management support in a Juniper product. This group became obsolete when additional objects were added
               juniPppLcpGroup7 1.3.6.1.4.1.4874.2.2.11.4.2.32
A collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product. This group became obsolete when additional objects were added.
               juniPppMlPppGroup8 1.3.6.1.4.1.4874.2.2.11.4.2.33
A collection of objects providing multi link PPP management support in a Juniper product. This was obsoleted when multiclass multilink support was added.
               juniPppLcpGroup8 1.3.6.1.4.1.4874.2.2.11.4.2.34
A collection of objects providing management of link-layer functionality (LCP) of PPP interfaces in a Juniper product.
               juniPppIpGroup5 1.3.6.1.4.1.4874.2.2.11.4.2.35
A collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product.This group became obsolete when additional objects were added.
               juniPppIpv6Group2 1.3.6.1.4.1.4874.2.2.11.4.2.36
A collection of objects providing management of IPV6 network control protocol functionality (IPV6CP) of PPP interfaces in a Juniper product.
               juniPppIpGroup6 1.3.6.1.4.1.4874.2.2.11.4.2.37
A collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product. This group became obsolete when juniPppPeerIpAddressOptional object added
               juniPppMlPppGroup9 1.3.6.1.4.1.4874.2.2.11.4.2.38
A collection of objects providing multi link PPP management support in a Juniper product.
               juniPppMlPppMulticlassTcGroup1 1.3.6.1.4.1.4874.2.2.11.4.2.39
A collection of object providing management of MCMP traffic class mapping functionality of PPP link interfaces in a Juniper product.
               juniPppIpGroup7 1.3.6.1.4.1.4874.2.2.11.4.2.40
A collection of objects providing management of IP network control protocol functionality (IPCP) of PPP interfaces in a Juniper product.