JUNIPER-PW-ATM-MIB: View SNMP OID List / Download MIB

VENDOR: JUNIPER


 Home MIB: JUNIPER-PW-ATM-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, JUNIPER-VPN-MIB, ATM-TC-MIB, JUNIPER-SMI, PerfHist-TC-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 jnxPWAtmMIB 1.3.6.1.4.1.2636.3.57
This MIB module defines objects used for managing the atm pseudowires in Juniper products.
       jnxpwAtmNotifications 1.3.6.1.4.1.2636.3.57.0
       jnxpwAtmObjects 1.3.6.1.4.1.2636.3.57.1
           jnxpwAtmCfgTable 1.3.6.1.4.1.2636.3.57.1.1 no-access
This table specifies generic information for an ATM PW to be carried over PSN in any mode.
               jnxpwAtmCfgEntry 1.3.6.1.4.1.2636.3.57.1.1.1 no-access
This table contains a set of parameters for the ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable. An entry is created for every newly ATM type associated pwIndex in the pwTable. Unless otherwise specified, all read-write objects in this table MAY be changed when the PW is defined as not active and all RW objects values must persist after reboot
                   jnxpwAtmCfgMaxCellConcatenation 1.3.6.1.4.1.2636.3.57.1.1.1.1 unsigned32 read-only
The maximum number of ATM cells that can be concatenated into one PW packet towards PSN. In non LDP or other signaling protocol environment, this object MAY be changed at anytime, but traffic might be interuppted, otherwise, it may be changed when PW is not active.
                   jnxpwAtmCfgFarEndMaxCellConcatenation 1.3.6.1.4.1.2636.3.57.1.1.1.2 unsigned32 read-only
The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will either return value 0 or allow setting it for calculating protocol overhead.
                   jnxpwAtmCfgTimeoutMode 1.3.6.1.4.1.2636.3.57.1.1.1.3 integer read-only
This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the time out is implementation specific-as such this object may be changed at any time under proper consideration of traffic interupption effect. Enumeration: 'disabled': 2, 'notApplicable': 1, 'enabled': 3.
                   jnxpwAtmClpQosMapping 1.3.6.1.4.1.2636.3.57.1.1.1.4 truthvalue read-only
This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields of the encapsulating protocol (e.g. EXP fields of the MPLS Label Stack). Selecting True allows the drop precedence to be preserved across the PSN. In transparent cell transport, the value of this object MUST be false(2), in other cases it can be changed at any time.
           jnxpwAtmOutboundNto1Table 1.3.6.1.4.1.2636.3.57.1.2 no-access
This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3).
               jnxpwAtmOutboundNto1Entry 1.3.6.1.4.1.2636.3.57.1.2.1 no-access
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all read-create objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
                   jnxpwAtmOutboundNto1AtmIf 1.3.6.1.4.1.2636.3.57.1.2.1.1 interfaceindex no-access
The ATM Interface that receives cells from the ATM network.
                   jnxpwAtmOutboundNto1Vpi 1.3.6.1.4.1.2636.3.57.1.2.1.2 atmvpidentifier no-access
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF
                   jnxpwAtmOutboundNto1Vci 1.3.6.1.4.1.2636.3.57.1.2.1.3 atmvcidentifier no-access
VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF
                   jnxpwAtmOutboundNto1RowStatus 1.3.6.1.4.1.2636.3.57.1.2.1.4 rowstatus read-only
This Object is used to create, modify or delete a row in this table.
                   jnxpwAtmOutboundNto1TrafficParamDescr 1.3.6.1.4.1.2636.3.57.1.2.1.5 rowpointer read-only
This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
                   jnxpwAtmOutboundNto1MappedVpi 1.3.6.1.4.1.2636.3.57.1.2.1.6 atmvpidentifier read-only
The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active
                   jnxpwAtmOutboundNto1MappedVci 1.3.6.1.4.1.2636.3.57.1.2.1.7 atmvcidentifier read-only
The egress generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
           jnxpwAtmInboundNto1Table 1.3.6.1.4.1.2636.3.57.1.3 no-access
This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following:atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3).
               jnxpwAtmInboundNto1Entry 1.3.6.1.4.1.2636.3.57.1.3.1 no-access
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all Read-Creat objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
                   jnxpwAtmInboundNto1AtmIf 1.3.6.1.4.1.2636.3.57.1.3.1.1 interfaceindex no-access
The ATM Interface that receives cells from the ATM network.
                   jnxpwAtmInboundNto1Vpi 1.3.6.1.4.1.2636.3.57.1.3.1.2 atmvpidentifier no-access
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF.
                   jnxpwAtmInboundNto1Vci 1.3.6.1.4.1.2636.3.57.1.3.1.3 atmvcidentifier no-access
VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF
                   jnxpwAtmInboundNto1RowStatus 1.3.6.1.4.1.2636.3.57.1.3.1.4 rowstatus read-only
This Object is used to create, modify or delete a row in this table.
                   jnxpwAtmInboundNto1TrafficParamDescr 1.3.6.1.4.1.2636.3.57.1.3.1.5 rowpointer read-only
This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
                   jnxpwAtmInboundNto1MappedVpi 1.3.6.1.4.1.2636.3.57.1.3.1.6 atmvpidentifier read-only
The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
                   jnxpwAtmInboundNto1MappedVci 1.3.6.1.4.1.2636.3.57.1.3.1.7 atmvcidentifier read-only
The generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
           jnxpwAtmPerfCurrentTable 1.3.6.1.4.1.2636.3.57.1.4 no-access
The current 15 minute interval counts are in this table. This table provides performance information per ATM PW.
               jnxpwAtmPerfCurrentEntry 1.3.6.1.4.1.2636.3.57.1.4.1 no-access
An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwAtmPerfInterval table and the counts in this entry are reset to zero.
                   jnxpwAtmPerfCurrentMissingPkts 1.3.6.1.4.1.2636.3.57.1.4.1.1 perfcurrentcount read-only
Number of missing packets (as detected via control word sequence number gaps).
                   jnxpwAtmPerfCurrentPktsReOrder 1.3.6.1.4.1.2636.3.57.1.4.1.2 perfcurrentcount read-only
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.
                   jnxpwAtmPerfCurrentPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.4.1.3 perfcurrentcount read-only
Number of packets detected out of order (via control word sequence numbers).
                   jnxpwAtmPerfCurrentPktsTimeout 1.3.6.1.4.1.2636.3.57.1.4.1.4 perfcurrentcount read-only
Number of packets transmitted due to timeout expiration while attempting to collect cells.
                   jnxpwAtmPerfCurrentPktsXmit 1.3.6.1.4.1.2636.3.57.1.4.1.5 counter64 read-only
Number of transmitted packets.
                   jnxpwAtmPerfCurrentCellsDropped 1.3.6.1.4.1.2636.3.57.1.4.1.6 perfcurrentcount read-only
Number of dropped cells.
                   jnxpwAtmPerfCurrentPktsReceived 1.3.6.1.4.1.2636.3.57.1.4.1.7 counter64 read-only
Number of received packets.
                   jnxpwAtmPerfCurrentUnknownCells 1.3.6.1.4.1.2636.3.57.1.4.1.8 counter64 read-only
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
           jnxpwAtmPerfIntervalTable 1.3.6.1.4.1.2636.3.57.1.5 no-access
This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period.
               jnxpwAtmPerfIntervalEntry 1.3.6.1.4.1.2636.3.57.1.5.1 no-access
An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval.
                   jnxpwAtmPerfIntervalNumber 1.3.6.1.4.1.2636.3.57.1.5.1.1 unsigned32 no-access
A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 96.
                   jnxpwAtmPerfIntervalValidData 1.3.6.1.4.1.2636.3.57.1.5.1.2 truthvalue read-only
This variable indicates if the data for this interval is valid.
                   jnxpwAtmPerfIntervalDuration 1.3.6.1.4.1.2636.3.57.1.5.1.3 unsigned32 read-only
The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.
                   jnxpwAtmPerfIntervalMissingPkts 1.3.6.1.4.1.2636.3.57.1.5.1.4 perfintervalcount read-only
Number of missing packets (as detected via control word sequence number gaps).
                   jnxpwAtmPerfIntervalPktsReOrder 1.3.6.1.4.1.2636.3.57.1.5.1.5 perfintervalcount read-only
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.
                   jnxpwAtmPerfIntervalPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.5.1.6 perfintervalcount read-only
Number of packets detected out of order (via control word sequence numbers).
                   jnxpwAtmPerfIntervalPktsTimeout 1.3.6.1.4.1.2636.3.57.1.5.1.7 perfintervalcount read-only
Number of packets transmitted due to timeout expiration.
                   jnxpwAtmPerfIntervalPktsXmit 1.3.6.1.4.1.2636.3.57.1.5.1.8 counter64 read-only
Number of transmitted packets.
                   jnxpwAtmPerfIntervalCellsDropped 1.3.6.1.4.1.2636.3.57.1.5.1.9 perfintervalcount read-only
Number of dropped cells.
                   jnxpwAtmPerfIntervalPktsReceived 1.3.6.1.4.1.2636.3.57.1.5.1.10 counter64 read-only
Number of received packets.
                   jnxpwAtmPerfIntervalUnknownCells 1.3.6.1.4.1.2636.3.57.1.5.1.11 counter64 read-only
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
           jnxpwAtmPerf1DayIntervalTable 1.3.6.1.4.1.2636.3.57.1.6 no-access
This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical 1 day intervals up to one full month.
               jnxpwAtmPerf1DayIntervalEntry 1.3.6.1.4.1.2636.3.57.1.6.1 no-access
An entry is created in this table by the agent for every entry in the pwAtmCfgTable table.
                   jnxpwAtmPerf1DayIntervalNumber 1.3.6.1.4.1.2636.3.57.1.6.1.1 unsigned32 no-access
The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively
                   jnxpwAtmPerf1DayIntervalValidData 1.3.6.1.4.1.2636.3.57.1.6.1.2 truthvalue read-only
This object indicates if the data for this interval is valid.
                   jnxpwAtmPerf1DayIntervalDuration 1.3.6.1.4.1.2636.3.57.1.6.1.3 unsigned32 read-only
The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.
                   jnxpwAtmPerf1DayIntervalMissingPkts 1.3.6.1.4.1.2636.3.57.1.6.1.4 counter32 read-only
Number of missing packets (as detected via control word sequence number gaps).
                   jnxpwAtmPerf1DayIntervalPktsReOrder 1.3.6.1.4.1.2636.3.57.1.6.1.5 counter32 read-only
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.
                   jnxpwAtmPerf1DayIntervalPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.6.1.6 counter32 read-only
Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered.
                   jnxpwAtmPerf1DayIntervalPktsTimeout 1.3.6.1.4.1.2636.3.57.1.6.1.7 counter32 read-only
Number of packets transmitted due to timeout expiration.
                   jnxpwAtmPerf1DayIntervalPktsXmit 1.3.6.1.4.1.2636.3.57.1.6.1.8 counter64 read-only
Number of transmitted packets.
                   jnxpwAtmPerf1DayIntervalCellsDropped 1.3.6.1.4.1.2636.3.57.1.6.1.9 counter32 read-only
Number of dropped cells.
                   jnxpwAtmPerf1DayIntervalPktsReceived 1.3.6.1.4.1.2636.3.57.1.6.1.10 counter64 read-only
Number of received packets.
                   jnxpwAtmPerf1DayIntervalUnknownCells 1.3.6.1.4.1.2636.3.57.1.6.1.11 counter64 read-only
Number of cells received from the PSN with unknown VPI or VCI value. This object is relevant only in N:1 mode.
       jnxpwAtmConformance 1.3.6.1.4.1.2636.3.57.2