JACOBS-RPL-MIB: View SNMP OID List / Download MIB

VENDOR: JACOBS UNIVERSITY BREMEN


 Home MIB: JACOBS-RPL-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, INET-ADDRESS-MIB, JACOBS-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 rplMib 1.3.6.1.4.1.30982.1.2
The MIB module for monitoring nodes implementing the IPv6 routing protocol for low power and lossy networks (RPL). Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
     rplNotifications 1.3.6.1.4.1.30982.1.2.0
     rplObjects 1.3.6.1.4.1.30982.1.2.1
         rplDefaults 1.3.6.1.4.1.30982.1.2.1.1
             rplDefaultDISMode 1.3.6.1.4.1.30982.1.2.1.1.1 rpldismode read-write
Determines whether a DIS message is send upon boot-up. Changes to this value may not persist across restarts.
             rplDefaultDISMessages 1.3.6.1.4.1.30982.1.2.1.1.2 unsigned32 read-write
The number of DIS messages that are sent as an initial probe for nearby DODAGs if the DIS mode is 'send'. The value of this object is ignored if the DIS mode is 'silent'. Changes to this value may not persist across restarts.
             rplDefaultDISTimeout 1.3.6.1.4.1.30982.1.2.1.1.3 unsigned32 read-write
The number of seconds after which a node in DIS mode 'send' in the absence of DIO messages may decide to root a floating DODAG. Changes to this value may not persist across restarts.
             rplDefaultDAODelay 1.3.6.1.4.1.30982.1.2.1.1.4 rpldaodelay read-write
The default delay for aggregations before a DAO is send. Changes to this value may not persist across restarts.
             rplDefaultDAOAckEnabled 1.3.6.1.4.1.30982.1.2.1.1.5 truthvalue read-write
Indicates whether DAO Acknowledgements are sent on this RPL instance. Changes to this value may not persist across restarts.
             rplDefaultPreference 1.3.6.1.4.1.30982.1.2.1.1.6 rpldodagpreference read-write
The default preference of this DODAG compared to other DODAGs within the same instance. Changes to this value may not persist across restarts.
             rplDefaultMinHopRankIncrease 1.3.6.1.4.1.30982.1.2.1.1.7 rplminhoprankincrease read-write
The default minimum increase of the rank in a single hop. Changes to this value may not persist across restarts.
             rplDefaultMaxRankIncrease 1.3.6.1.4.1.30982.1.2.1.1.8 unsigned32 read-write
The default maximum allowable increase in rank in support of local repair. If DAGMaxRankIncrease is 0 then this mechanism is disabled. Changes to this value may not persist across restarts.
             rplDefaultModeOfOperation 1.3.6.1.4.1.30982.1.2.1.1.9 rplmodeofoperation read-write
The mode of operation of the RPL instance. Changes to this value may not persist across restarts.
             rplDefaultIntervalDoublings 1.3.6.1.4.1.30982.1.2.1.1.10 unsigned32 read-write
The default Imax parameter of the DIO trickle timer. Changes to this value may not persist across restarts.
             rplDefaultIntervalMin 1.3.6.1.4.1.30982.1.2.1.1.11 unsigned32 read-write
The default Imin parameter of the DIO trickle timer. Changes to this value may not persist across restarts.
             rplDefaultRedundancyConstant 1.3.6.1.4.1.30982.1.2.1.1.12 unsigned32 read-write
The default k parameter of the DIO trickle timer. Changes to this value may not persist across restarts.
         rplActive 1.3.6.1.4.1.30982.1.2.1.2
             rplActiveInstance 1.3.6.1.4.1.30982.1.2.1.2.1 rplinstanceid read-write
The currently active RPL Instance. Changes to this value may not persist across restarts.
             rplActiveDodag 1.3.6.1.4.1.30982.1.2.1.2.2 inetaddressipv6 read-write
The currently active RPL DODAG in the active RPL Instance. Changes to this value may not persist across restarts.
             rplActiveDodagTriggerSequence 1.3.6.1.4.1.30982.1.2.1.2.3 unsigned32 read-write
The DAO Trigger Sequence Number (DTSN) of the active DODAG as defined in Section 6.3.1 of RFC 6550. Changes to this value may not persist across restarts.
         rplOCPTable 1.3.6.1.4.1.30982.1.2.1.3 no-access
The table of all supported Objective Code Points (OCPs).
             rplOCPEntry 1.3.6.1.4.1.30982.1.2.1.3.1 no-access
An entry representing a supported Objective Code Point.
                 rplOCPCodepoint 1.3.6.1.4.1.30982.1.2.1.3.1.1 rplobjectivecodepoint no-access
A supported Objective Code Point.
                 rplOCPEnabled 1.3.6.1.4.1.30982.1.2.1.3.1.2 truthvalue read-write
Enables the usage of this Objective Code Point. Changes to this value may not persist across restarts.
         rplInstanceTable 1.3.6.1.4.1.30982.1.2.1.4 no-access
The table represents information about all known RPL Instances.
             rplInstanceEntry 1.3.6.1.4.1.30982.1.2.1.4.1 no-access
An entry representing information about a RPL Instance.
                 rplInstanceID 1.3.6.1.4.1.30982.1.2.1.4.1.1 rplinstanceid no-access
The InstanceID of this RPL Instance.
                 rplInstanceDISMode 1.3.6.1.4.1.30982.1.2.1.4.1.2 rpldismode read-only
Reports whether a DIS message is send for this instance upon boot-up.
                 rplInstanceDISMessages 1.3.6.1.4.1.30982.1.2.1.4.1.3 unsigned32 read-only
The number of DIS messages that are sent as an initial probe for nearby DODAGs if the DIS mode is 'send'.
                 rplInstanceDISTimeout 1.3.6.1.4.1.30982.1.2.1.4.1.4 unsigned32 read-only
The number of seconds after which a node in DIS mode 'send' in the absence of DIO messages may decide to root a floating DODAG.
                 rplInstanceModeOfOperation 1.3.6.1.4.1.30982.1.2.1.4.1.5 rplmodeofoperation read-only
The mode of operation of the RPL instance.
         rplDodagTable 1.3.6.1.4.1.30982.1.2.1.5 no-access
The table represents information about all locally known DODAGs.
             rplDodagEntry 1.3.6.1.4.1.30982.1.2.1.5.1 no-access
An entry representing information about a DODAG.
                 rplDodagIndex 1.3.6.1.4.1.30982.1.2.1.5.1.1 unsigned32 no-access
The index identifying a DODAG within an RPL instance. This index is used to keep the table indexes short. The RPL protocol identifies a DODAG within an RPL instance by the DODAGID.
                 rplDodagID 1.3.6.1.4.1.30982.1.2.1.5.1.2 inetaddressipv6 read-only
The identifier of a DODAG root (DODAGID) of this RPL instance. The root of the DODAG reports its own IPv6 address as the DODAG root. This is uniquely identifying a DODAG within an RPL instance.
                 rplDodagVersion 1.3.6.1.4.1.30982.1.2.1.5.1.3 rpldodagversionnumber read-only
The version of the DODAG in this RPL instance.
                 rplDodagRank 1.3.6.1.4.1.30982.1.2.1.5.1.4 rplrank read-only
The rank of the node within the DODAG.
                 rplDodagState 1.3.6.1.4.1.30982.1.2.1.5.1.5 integer read-only
The status of the DODAG: other(0) An unknown state. grounded(1) The DODAG is grounded. floating(2) The DODAG is floating (not grounded). Enumeration: 'floating': 2, 'other': 0, 'grounded': 1.
                 rplDodagOCP 1.3.6.1.4.1.30982.1.2.1.5.1.6 rplobjectivecodepoint read-only
The Objective Code Point of this DODAG.
                 rplDodagDAODelay 1.3.6.1.4.1.30982.1.2.1.5.1.7 rpldaodelay read-only
The delay for aggregations before a DAO is send.
                 rplDodagDAOAckEnabled 1.3.6.1.4.1.30982.1.2.1.5.1.8 truthvalue read-only
Indicates whether DAO Acknowledgements are sent on this DODAG.
                 rplDodagPreference 1.3.6.1.4.1.30982.1.2.1.5.1.9 rpldodagpreference read-only
How preferred this DODAG is compared to other DODAGs within the same instance.
                 rplDodagMinHopRankIncrease 1.3.6.1.4.1.30982.1.2.1.5.1.10 rplminhoprankincrease read-only
The minimum increase of the rank in a single hop.
                 rplDodagMaxRankIncrease 1.3.6.1.4.1.30982.1.2.1.5.1.11 unsigned32 read-only
The maximum allowable increase in rank in support of local repair. If DAGMaxRankIncrease is 0 then this mechanism is disabled.
                 rplDodagIntervalDoublings 1.3.6.1.4.1.30982.1.2.1.5.1.12 unsigned32 read-only
The Imax parameter of the DIO trickle timer.
                 rplDodagIntervalMin 1.3.6.1.4.1.30982.1.2.1.5.1.13 unsigned32 read-only
The Imin parameter of the DIO trickle timer.
                 rplDodagRedundancyConstant 1.3.6.1.4.1.30982.1.2.1.5.1.14 unsigned32 read-only
The k parameter of the DIO trickle timer.
                 rplDodagPathControlSize 1.3.6.1.4.1.30982.1.2.1.5.1.15 rplpathcontrolsize read-only
The Path Control Size of this DODAG.
         rplDodagParentTable 1.3.6.1.4.1.30982.1.2.1.6 no-access
The list of parents for a DODAG.
             rplDodagParentEntry 1.3.6.1.4.1.30982.1.2.1.6.1 no-access
Information about a known DODAG parent.
                 rplDodagParentID 1.3.6.1.4.1.30982.1.2.1.6.1.1 inetaddressipv6 no-access
An RPL parent associated with this DODAG.
                 rplDodagParentIf 1.3.6.1.4.1.30982.1.2.1.6.1.2 interfaceindex read-only
The interface over which the parent can be reached.
         rplDodagChildTable 1.3.6.1.4.1.30982.1.2.1.7 no-access
The list of children for a DODAG.
             rplDodagChildEntry 1.3.6.1.4.1.30982.1.2.1.7.1 no-access
Information about a known DODAG child.
                 rplDodagChildID 1.3.6.1.4.1.30982.1.2.1.7.1.1 inetaddressipv6 no-access
An RPL child associated with this DODAG.
                 rplDodagChildIf 1.3.6.1.4.1.30982.1.2.1.7.1.2 interfaceindex read-only
The interface over which the child can be reached.
         rplStats 1.3.6.1.4.1.30982.1.2.1.8
             rplMemOverflows 1.3.6.1.4.1.30982.1.2.1.8.1 counter32 read-only
The number of memory allocation failures (e.g., routing table overflows).
             rplParseErrors 1.3.6.1.4.1.30982.1.2.1.8.2 counter32 read-only
The number of received malformed messages.
             rplUnknownMsgTypes 1.3.6.1.4.1.30982.1.2.1.8.3 counter32 read-only
The number of received RPL messages that we dropped because the message type is not recognized by the implementation.
             rplSecurityPolicyViolations 1.3.6.1.4.1.30982.1.2.1.8.4 counter32 read-only
The number of messages discarded because the described level of security for the message type and originator is unknown or does not meet locally maintained security policies as defined in Section 10.7. of RFC 6550.
             rplIntegrityCheckFailures 1.3.6.1.4.1.30982.1.2.1.8.5 counter32 read-only
The number of messages discarded because the integrity check failed against the received message authentication code (MAC) as defined in Section 10.7. of RFC 6550.
             rplReplayProtectionFailures 1.3.6.1.4.1.30982.1.2.1.8.6 counter32 read-only
The number of messages discarded because the received message Counter value is non-zero and less than the maintained incoming Counter watermark or because the received Timestamp Counter value indicates a message transmission time that is earlier than the Current time less the acceptable packet delay as defined in Section 10.7. of RFC 6550. This counter is also incremented if the temporal consistency check of the message fails as defined in Section 10.7.1.
             rplValidParentFailures 1.3.6.1.4.1.30982.1.2.1.8.7 counter32 read-only
The number of times a packet could not be sent to a DODAG parent flagged as valid.
             rplNoInstanceIDs 1.3.6.1.4.1.30982.1.2.1.8.8 counter32 read-only
The number of times a packet could not be sent because of a missing RPLInstanceID.
             rplTriggeredLocalRepairs 1.3.6.1.4.1.30982.1.2.1.8.9 counter32 read-only
The number of times a local repair procedure was triggered.
             rplTriggeredGlobalRepairs 1.3.6.1.4.1.30982.1.2.1.8.10 counter32 read-only
The number of times a global repair procedure was triggered.
             rplNoParentSecs 1.3.6.1.4.1.30982.1.2.1.8.11 counter32 read-only
The number of seconds without a next hop (DODAG parent).
             rplActiveNoParentSecs 1.3.6.1.4.1.30982.1.2.1.8.12 counter32 read-only
The number of seconds with packets to forward without a next hop (DODAG parent).
             rplOBitSetDownwards 1.3.6.1.4.1.30982.1.2.1.8.13 counter32 read-only
Number of packets received with the 'O' bit set from a node with a higher rank as defined in Section 18.3.2 of RFC 6550.
             rplOBitClearedUpwards 1.3.6.1.4.1.30982.1.2.1.8.14 counter32 read-only
Number of packets received with the 'O' bit cleared from a node with a lower rank as defined in Section 18.3.2 of RFC 6550.
             rplFBitSet 1.3.6.1.4.1.30982.1.2.1.8.15 counter32 read-only
Number of packets received with the 'F' bit set as defined in Section 18.3.2 of RFC 6550.
             rplRBitSet 1.3.6.1.4.1.30982.1.2.1.8.16 counter32 read-only
Number of packets received with the 'R' bit set as defined in Section 18.3.2 of RFC 6550.
             rplTrickleTimerResets 1.3.6.1.4.1.30982.1.2.1.8.17 counter32 read-only
The number of trickle timer resets.
         rplMsgStatsTable 1.3.6.1.4.1.30982.1.2.1.9 no-access
Basic RPL message statistics by message type.
             rplMsgStatsEntry 1.3.6.1.4.1.30982.1.2.1.9.1 no-access
Statistics for a specific RPL message type.
                 rplMsgStatsType 1.3.6.1.4.1.30982.1.2.1.9.1.1 rplmessagetype no-access
The RPL message type being counted by this row.
                 rplMsgStatsInMsgs 1.3.6.1.4.1.30982.1.2.1.9.1.2 counter32 read-only
The number of RPL messages received of this type.
                 rplMsgStatsOutMsgs 1.3.6.1.4.1.30982.1.2.1.9.1.3 counter32 read-only
The number of RPL messages sent of this type.
     rplConformance 1.3.6.1.4.1.30982.1.2.2
         rplGroups 1.3.6.1.4.1.30982.1.2.2.1
             rplGeneralGroup 1.3.6.1.4.1.30982.1.2.2.1.1
A collection of objects providing general information about the RPL implementation.
             rplInstanceGroup 1.3.6.1.4.1.30982.1.2.2.1.2
A collection of objects providing insight into RPL Instances and RPL DODAGs.
             rplStatsGroup 1.3.6.1.4.1.30982.1.2.2.1.3
A collection of objects providing statistics about the RPL implementation.
         rplCompliances 1.3.6.1.4.1.30982.1.2.2.2
             rplFullCompliance 1.3.6.1.4.1.30982.1.2.2.2.1
Compliance statement for implementations supporting read/write access, according to the object definitions.
             rplReadOnlyCompliance 1.3.6.1.4.1.30982.1.2.2.2.2
Compliance statement for implementations supporting only readonly access.