HUAWEI-SERVER-IBMC-MIB: View SNMP OID List / Download MIB

The HUAWEI-SERVER-IBMC-MIB contains objects to Manage the server.

systemHealth information about system present state of health. This value will be one of the following: (1-OK, 2-Minor, 3-Major, 4-Critical) Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'minor': 2.

Decide the system's first boot device. 1 - No override 2 - Force PXE 3 - Force boot from default Hard-drive 4 - Force boot from default CD/DVD 5 - Force boot from Floppy/primary removable media 6 - boot flags valid. The bit should be set to indicate that valid flag data is present. This bit may be automatically cleared based on the boot flag valid bit clearing parameter, above.(This option is read-only.) 7 - Force boot into BIOS SETUP The default value is 6 (unspecified) Enumeration: 'biossetup': 7, 'unspecified': 6, 'hdd': 3, 'pxe': 2, 'cdDvd': 4, 'floppyPrimaryRemovableMedia': 5, 'noOverride': 1.

systemTime information about iBMC system time, based on UTC. the value such as (yyyy-mm-dd hh:mm:ss).

systemTimeZone information about iBMC time zone. The value is in [-720, 840].

The system safe poweroff time, the value 0 indicates non-timeout.

The device name value between 1 to 63 characters.

The device serial number value between 1 to 63 characters.

1 - Stay Off 2 - Restore Previous State 3 - Turn On Default value is turnon(3). Enumeration: 'turnon': 3, 'restorePreviousState': 2, 'stayoff': 1.

The host name between 1 to 64 characters. Supported characters: 0-9 a-z A-Z - ('-' is not allowed to be the first/last character). Default value is huawei.

The GUID is hex string such as ********-****-****-****-************.

identify use to control on or off of led. identify mode: 0 - Off 1 - Temporary On 2 - Force Identify On set format: ,[ontime] get format: When = 0 or = 2, the format is only . [ontime] is option and value is in [1,255], When set Temporary On without [ontime], The default Temporary On time are 15 seconds.

System Power Status Get. 1 - Power Off 2 - Power On System Power Status Set. 1 - Normal Power Off 2 - Power On 3 - Forced System Reset 4 - Forced Power Cycle 5 - Forced Power Off The set actions are a process which will take effect in a while. When system in poweroff state, Power Off/Reset/PowerOffThenOn commonds are not supported. Enumeration: 'forcedSystemReset': 3, 'forcedPowerCycle': 4, 'powerOn': 2, 'normalPowerOff': 1, 'forcedPowerOff': 5.

Display the present system power.

The device owner ID, maxlength is 64 characters.

The device slot ID of a server exists, the value ranges from 1 to 80. Otherwise, the value is 0.

The remoteOEMinfo, maxlength is 255 characters.

The deviceLocationInfo between 0 and 64 characters. Default value is server room.

The deviceRemoteManageID between 0 and 64 characters.

Reboot the BMC management system.When set, the value is only 1, write only. Enumeration: 'reboot': 1.

Set power on permission. notPermit 1, permit 2. Enumeration: 'permit': 2, 'notPermit': 1.

Auto discovery state. disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

The productUniqueID is hex string.

Percent of CPU usage. The value defined as: -1: invalid current CPU usage. [0,100]: represents the current CPU usage.

System boot once or permanent. once 1, permanent 2. Default value is once(1). Enumeration: 'permanent': 2, 'once': 1.

Percent of memory usage. The value defined as: -1: invalid current memory usage. [0,100]: represents the current memory usage.

Percent of CPU usage threshold. This value is in [0,100].

Percent of memory usage threshold. This value is in [0,100].

Percent of hard disk partition usage threshold. This value is in [0,100].

systemTimeZone information about iBMC time zone. The value can be time-offset : GMT-12:00~GMT+14:00 e.g. GMT+08:00,GMT-04:30. The value can be city name , e.g. Asia/Shanghai,America/New_York.

A table containing the part component.

.

Information about event id.

The sensor name between 1 to 16 characters.

The format of alert time is yyyy-mm-dd hh:mm:ss, based on UTC.

The information about event level. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'minor': 2.

The event description between 1 to 255 characters.

The information about event code.

The object identification of current event.

A table containing the hard disk partition information.

.

Information about hard disk Partition Index.

The hard disk partition name between 1 to 64 characters.

The hard disk partition total capactity, unit GB.

The usage of hard disk partion.

Domain Name between 0 to 67 characters. A domain name supports all characters except space,double quotation,equal and the following characters:#'&.

Preferred DNS server IPv4 address. this value is right IPv4 address or empty, the default value is empty.

Alternate DNS server IPv4 address. this value is right IPv4 address or empty, the default value is empty.

Information about DNS source. Enumeration: 'auto': 2, 'manual': 1.

Information about DNS bind net port. Enumeration: 'eth1': 2, 'eth0': 1.

Information about DNS bind ip protocol. Enumeration: 'ipv4': 1, 'ipv6': 2.

The state of LDAP. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

LDAP domain server between 1 to 255 characters. Default value is 0.0.0.0. Max length is 255 characters.

LDAP user domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. CN=employee,OU=company,DC=ldap,DC=ibmc,DC=com or OU=department,OU=company,DC=ldap,DC=ibmc.

Specifies the port number for the LDAP service. Value: an integer ranging from 1 to 65535 The default value is 636.

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

A table containing the list of LDAP information.

.

LDAP group index.

LDAP group name if the string consists of numbers, letters, and special characters, the maximum length is 255 characters.

0 - no access 1 - common user 2 - operator 3 - administrator 4 - custom role1 5 - custom role2 6 - custom role3 7 - custom role4 Default value is commonUser(1). Enumeration: 'customRole4': 7, 'administrator': 3, 'customRole1': 4, 'customRole2': 5, 'noAccess': 0, 'customRole3': 6, 'operator': 2, 'commonUser': 1.

Information about LDAP group login interfaces. bit0 - Web: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit7 - Redfish: 0 disabled; 1 enabled

LDAP group domain if the string consists of numbers, letters, and special characters, the maximum length is 255 characters. E.g. Group0 CN=group0,DC=ldap,DC=ibmc,DC=com.

The state of Trap. Default value is enable(2). Enumeration: 'enable': 2, 'disable': 1.

SNMP trap community between 1 to 18 characters. A community supports all characters except space.

The level of trap send. Default level is minor. ok:send all level message. minor:send minor and above level message. major:send major and above level message. critical:send critical level message. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'minor': 2.

Trap mode. Enumeration: 'trapOidMode': 2, 'trapPreciseAlarmMode': 3, 'eventCodeMode': 1.

Trap version. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

Send rearm commomnd. Enumeration: 'rearm': 1.

Choose the server Identity when sending trap. Enumeration: 'boardSN': 1, 'productAssetTag': 2, 'hostName': 3.

The security user name for SNMP TRAP V3, the user should be one of the BMC local user.

The level of trap send. Support set/get any combination of the 4 alarm levels(critical,major,minor,normal), use comma to separate them. none/all is also supported,but never use it with the 4 levels together. e.g. To set critical + major level message, just set: critical,major To set critical level message, just set: critical To set all level message, just set: all

A table containing the list of Trap information.

Information about a trap group.

Trap Receiver state enable 2, disable 1. Enumeration: 'enable': 2, 'disable': 1.

Trap Receiver IPv4 addrsss, IPv6 address or domain name. Default value is empty.

SNMP trap port, default is 162.

Send message type snmptrap. Enumeration: 'snmpTrap': 1.

Test the SNMP trap or syslog whether could send. When set, the value is only 1.

BOB: iBMC over iBMA. Use in-band channel forwarding trap: enabled 2, disabled 1. Enumeration: 'enable': 2, 'disable': 1.

The state of SMTP. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

The severity of SMTP send. Default Severity is ok(1). ok:Send all level message. minor:Send minor and above level message. major:Send major and above level message. critical:Send critical level message. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'minor': 2.

The SMTP server IPv4 address, IPv6 address or domain name. Default value is empty.

SMTP login type anonymous 1, account 2. Default value is anonymous(1). Enumeration: 'account': 2, 'anonymous': 1.

Login account between 1 to 64 characters. A login account supports all characters except space,double quotationthe,equal and the following characters:#'&.

Set user login SMTP password. Login password between 1 to 50 characters.

Send from between 0 to 255 characters. A send from supports all characters except space,double quotation,equal and the following characters:#'&.

The TLS state for SMTP. Default value is enable(2). Enumeration: 'enable': 2, 'disable': 1.

The severity of SMTP send. Support set/get any combination of the 4 alarm levels(critical,major,minor,normal), use comma to separate them. none/all is also supported,but never use it with the 4 levels together. e.g. To set critical + major level message, just set: critical,major To set critical level message, just set: critical To set all level message, just set: all

A table containing the list of SMTP Receiver information.

Information about SMTP Receiver information.

Smtp receiver index.

SMTP receiver enable state. Disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

Email address between 0 to 255 characters. A email address supports all characters except space,double quotation,equal and the following characters:#'&.

Email description between 0 to 255 characters. A email description supports all characters except double quotation,equal and the following characters:#'&.

Test whether could send email. When set, the value is only 1.

Information about all power supply health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Setted power supply entire mode. Power supply entire mode get: 1:loadBalance(1) 2:activeBackup(2) 3:unsupport(3) Power supply entire mode set: 1:loadBalance(1) 2:activeBackup(2) Enumeration: 'activeStandby': 2, 'unsupport': 3, 'loadBalance': 1.

Actual power supply entire mode. Enumeration: 'activeStandby': 2, 'unknown': 3, 'loadBalance': 1.

Setted active power supply. per bit represents a PS, bit0 is PS1, and so on, the bit value of 1 indicates the PS is active.can not set all PS are active or backup.The result 0x7FFFFFFF is unsupport.

A table containing the list of power supply information.

Information about power supply.

Power supply index.

Information about power manufacture.

Information about power input. Enumeration: 'acInput': 1, 'acInputDcInput': 3, 'dcInput': 2.

Information about power Model.

Information about power version.

Information about power rating.

Information about power status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Information about input power. The unit is watt.

Information about power presence status. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Information about power protocol. Enumeration: 'pmbus': 2, 'psmi': 1.

Power supply physical location.

Power supply logic function.

Power supply devicename.

power supply actual work mode. Enumeration: 'active': 1, 'unknown': 3, 'backup': 2.

Power supply SN.

A table containing the list of fru power information.

Information about fru power supply.

The index of the FRU power.

Information about fru power control. Enumeration: 'forcedSystemReset': 3, 'forcedPowerCycle': 4, 'powerOn': 2, 'normalPowerOff': 1.

Fan control mode manual or auto. fan mode: 0 - auto 1 - manual set format: ,[timeout] get format: ,[timeout] When = 0, the format is only . [timeout] is option and value is in [0,300],unit is second, When set, if fan mode is manual and without [timeout], The default out time is 30 seconds.

Percent of fan speed. This value is in [MIN_FANLEVEL,100]. MIN_FANLEVEL is the minimum fanlevel according to systems, particular, when get, 255 represent fan mode is auto.

Information about all fan health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the list of fan information.

Information about fan information.

Fan index.

Information about fan speed, Unit is RPM.

Information about fan presence. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Information about fan health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Fan physical location.

Fan logic function.

Fan devicename.

Fan speed ratio.

A table containing the list of led information.

Information about led.

FRU Led index.

FRU Led name.

Led capbility: BLUE,RED,GREEN,AMBER,ORANGE,WHITE. Return value seprate by ','.

Led control state: BLUE,RED,GREEN,AMBER,ORANGE,WHITE.

Led override: BLUE,RED,GREEN,AMBER,ORANGE,WHITE.

Led color now: BLUE,RED,GREEN,AMBER,ORANGE,WHITE.

Information about LED mode. Enumeration: 'localControl': 1, 'override': 2, 'test': 3.

Information LED status now. Enumeration: 'on': 2, 'off': 1, 'blinking': 3.

Unit:10ms(Blinking),100ms(Test) Range:(1~250)*10ms(Blinking), (1~127)*100ms(Test).

Unit:10ms(Blinking) Range:(1~250)*10ms(Blinking).

A table containing the part component.

Information about led.

Information about component name.

Information about component type. Enumeration: 'm2TransferCard': 46, 'amcController': 3, 'passThroughCard': 68, 'riserCard': 16, 'pcieRetimer': 70, 'cpuBoard': 10, 'logicalDrive': 69, 'memoryBoard': 12, 'lomCard': 13, 'pcieCard': 9, 'hddBackPlane': 5, 'baseBoard': 1, 'fanBoard': 24, 'raidCard': 6, 'mmcController': 4, 'mezzCard': 2, 'gpuBoard': 64, 'ioBoard': 11, 'pcieTransferCard': 39.

Information about PCB version.

Information about board ID.

Information about board health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the part firmware.

Information about firmware.

Information about firmware name.

Information about firmware type. Enumeration: 'hddBackPlaneCpld': 10, 'uboot': 5, 'pcieRiserCardCpld': 11, 'fpga': 2, 'peripheralFirmware': 13, 'gpuBoardCpld': 14, 'cpuboardCpld': 9, 'bios': 4, 'lcd': 6, 'raidCardCpld': 12, 'iBMC': 1, 'ioboardCpld': 8, 'backupUboot': 7, 'cpld': 3.

Information about firmware release date.

Information about firmware version.

Information about firmware location.

Information about FRU id.

Information about firmware Board.

A table containing the ethernet.

Information about ethernet.

Information about ethernet port number.

Information about ethernet IP address.

Information about netmask.

Information about default gateway.

Information about IP source. Enumeration: 'dhcp': 2, 'static': 1.

Information about MAC address.

Information about ethernet port type. Enumeration: 'share': 2, 'mgmt': 1.

Information about share ethernet binded host port. Enumeration: 'none': 1, 'port4': 5, 'port2': 3, 'port3': 4, 'port1': 2.

Information about eth enabled. Enumeration: 'enable': 2, 'disable': 1.

Information about ethernet Mode. Enumeration: 'dedicated': 1, 'pcieShare': 4, 'lomShare': 2, 'adaptive': 3.

Disable or enable VLAN and set ID. Set 'off' to disabled VLAN. Set [1,4094] to enable VLAN and set ID.

Set IPaddr,Netmask,Gateway. eg.: 192.168.2.100,255.255.255.0,192.168.2.1

Information about eth IPv4 enabled. Enumeration: 'enable': 2, 'disable': 1.

A table containing the sensor.

Information about sensor.

Information about sensor name.

Sensor current reading.

Information about sensor upper nonrecoverable threshold.

Information about sensor upper crtical threshold.

Information about sensor upper minor threshold.

Information about sensor lower nonrecoverable threshold.

Information about sensor lower crtical threshold.

Information about sensor lower minor threshold.

Information about sensor status.

Information about sensor type.

Positive-going Threshold Hysteresis Value. Set to 00h if sensor does not support positive-going threshold hysteresis. This value is subtracted from positive going thresholds to determine the point where the asserted status for that threshold will clear. See section 35.13.2, Hysteresis and Event Status and section 35.13.3, High-going versus Low-going Threshold Events.

Negative-going Threshold Hysteresis Value. This value is added to negative going thresholds to determine the point where the asserted status for that threshold will clear. Set to 00h if sensor does not support negative-going threshold hysteresis.

Positive-going Threshold Hysteresis Value. Set to 'na' if sensor does not support positive-going threshold hysteresis. This value is subtracted from positive going thresholds to determine the point where the asserted status for that threshold will clear. See section 35.13.2, Hysteresis and Event Status and section 35.13.3, High-going versus Low-going Threshold Events.

Negative-going Threshold Hysteresis Value. This value is added to negative going thresholds to determine the point where the asserted status for that threshold will clear. Set to 'na' if sensor does not support negative-going threshold hysteresis.

Information about sensor unit. Enumeration: 'watts': 6, 'volts': 4, 'unspecified': 0, 'degrees-f': 2, 'degrees-c': 1, 'amps': 5, 'rpm': 18, 'degrees-k': 3.

Information about event reading type.

A table containing the user.

Information about user.

Information about user id, the vaule is in [2, 17].

Information about user enable status , disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

User name length is 1 to 16 characters. The value can contain letters, digits, and special characters. The value cannot contain spaces, double quotation and the following special characters: , \ : < > & ' / %, and cannot start with a number sign (#).

Information about user password. User password length is 1 to 20 characters.

Information about user group. When set, this vaule will be one of the following:(1, 2, 3, 5, 6, 7, 8). 1 - common user 2 - operator 3 - administrator 4 - no access(only for get) 5 - custom role1 6 - custom role2 7 - custom role3 8 - custom role4. Enumeration: 'customRole4': 8, 'administrator': 3, 'customRole1': 5, 'customRole2': 6, 'noAccess': 4, 'customRole3': 7, 'operator': 2, 'commonUser': 1.

Information about delete user. This vaule will be one of the following: (delete(1)). Enumeration: 'delete': 1.

Information about user login interfaces. bit0 - Web: 0 disabled; 1 enabled bit1 - SNMP: 0 disabled; 1 enabled bit2 - IPMI: 0 disabled; 1 enabled bit3 - SSH: 0 disabled; 1 enabled bit4 - SFTP: 0 disabled; 1 enabled bit6 - Local: 0 disabled; 1 enabled bit7 - Redfish:0 disabled; 1 enabled

Add PublicKey, the set format is: , with max length 256.

Delete PublicKey

PublicKey Hash

Information about SNMP privacy password of user. Password length is 1 to 20 characters. It is not supported on server of V3 series.

Information about all cpu health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the CPU information.

Information about CPU.

Information about CPU index.

Information about CPU manufacturer.

Information about CPU family.

Information about CPU type.

Information about CPU clock rate.

Information about CPU health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Information about CPU availability. Enumeration: 'disabled': 2, 'unknown': 1, 'backup': 3, 'active': 4.

CPU physical location.

CPU logic function.

CPU devicename.

CPU ProcessorID.

CPU CoreCount.

CPU ThreadCount.

CPU memory technology.

CPU Cache.

CPU Cache.

CPU Cache.

Information about all memory health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the memory.

Information about memory.

Information about memory DIMM index.

Information about memory logic channel.

Information about memory manufacturer.

Information about memory capacity.

Information about memory clock rate.

Information about memory health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Information about memory availability. Enumeration: 'disabled': 2, 'unknown': 1, 'backup': 3, 'active': 4.

Memory physical location.

Memory logic function.

Memory devicename.

Information about memory type.

Information about memory SN.

Information about memory minimum voltage.

Information about memory rank.

Information about memory bit width.

Information about memory technology.

A table containing the LOM.

Information about LOM.

Information about LOM index.

Information about LOM MAC address.

Information about all hard disk health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the hard disk.

Information about hard disk.

Information about hard disk index.

Information about hard disk presence. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Information about hard disk health. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Hard disk physical location.

Hard disk logic function.

Hard disk devicename.

Hard disk serial number.

Hard disk model number.

Hard disk manufacturer.

Hard disk firmware state. 1: Unconfigured Good Can be set from Unconfigured Bad state, or JBOD state when raidControllerJBODEnable = Enabled. 2: Unconfigured Bad (read only) 3: Hot Spared (read only) 4: Offline Can be set from Online state. 5: Failed (read only) 6: Rebuild (read only) 7: Online Can be set from Offline state. 8: Copyback (read only) 9: JBOD Can be set from Unconfigured Good state when raidControllerJBODEnable = Enabled. 10: Unconfigured Shielded (read only) 11: Hot Spare Shielded (read only) 12: Configured Shielded (read only) 13: Foreign (read only) 14: Active (read only) 15: Stand-by (read only) 16: Sleep (read only) 17: DST executing in background (read only) 18: SMART Off-line Data Collection executing in background (read only) 19: SCT command executing in background (read only) 255: Unknown (read only) Enumeration: 'dst': 17, 'copyback': 8, 'unconfigured-bad': 2, 'unconfigured-good': 1, 'unknown': 255, 'rebuild': 6, 'standby': 15, 'foreign': 13, 'jbod': 9, 'failed': 5, 'sleep': 16, 'configured-shielded': 12, 'online': 7, 'active': 14, 'sct': 19, 'hot-spare': 3, 'smart': 18, 'offline': 4, 'hot-spare-shielded': 11, 'unconfigured-shielded': 10.

Hard disk firmware version.

Hard disk capacity (GB). Enumeration: 'unknown': 4294967295.

Hard disk media type. Enumeration: 'ssm': 3, 'ssd': 2, 'hdd': 1, 'unknown': 255.

Hard disk interface type. SAS, SATA...etc. 1: Undefined 2: Parallel-SCSI 3: SAS 4: SATA 5: Fiber Channel 6: SATA/SAS 7: PCIe 255: Unknown Enumeration: 'parallel-scsi': 2, 'undefined': 1, 'sata': 4, 'unknown': 255, 'sata-sas': 6, 'sas': 3, 'fiber-channel': 5, 'pcie': 7.

Hard disk power state. Enumeration: 'unknown': 255, 'transition': 3, 'spun-down': 2, 'spun-up': 1.

Hard disk rebuild progress (0 - 100%). Enumeration: 'unknown': 255.

Hard disk patrol read status. Enumeration: 'in-progress': 2, 'unknown': 255, 'stopped': 1.

Hard disk maximum supported speed. Enumeration: 'unknown': 4294967295.

Hard disk negotiated speed. Enumeration: 'unknown': 4294967295.

Hard disk temperature (in Celsius). Enumeration: 'unknown': 255.

Hard disk SAS address 1.

Hard disk SAS address 2.

Hard disk prefail state. Enumeration: 'unknown': 255, 'yes': 2, 'no': 1.

Hard disk hot spare state. 1: None Cancel the global/dedicated hot spare setting, can be set when hardDiskHotSpareState is Global/Dedicated. 2: Global Can be set only when hardDiskFwState = Unconfigured Good. 3: Dedicated Can be set only when hardDiskFwState = Unconfigured Good. Setting value described as following: Byte1 - Indicating the hard disk used as dedicated hot spare, fixed to 3. Byte2 - The logical drive index which the hard disk spared for, started from 1. For example: Set this hard disk as dedicated hot spare for logical drive 2, the setting value should be 0x0203 = 2 * 256 + 3 = 515. 4: Commissioned (read only) 5: Emergency (read only) 255: Unknown (read only) Enumeration: 'none': 1, 'emergency': 5, 'unknown': 255, 'global': 2, 'dedicated': 3, 'commissioned': 4.

Hard disk remnant wearout (100% - 0). Only valid for SSD. Enumeration: 'unknown': 255.

Hard disk media error count. Enumeration: 'unknown': 4294967295.

Hard disk prefail error count. Enumeration: 'unknown': 4294967295.

Hard disk other error count. Enumeration: 'unknown': 4294967295.

Hard disk location state. 1: Unknown (read only) 2: Off 3: On Enumeration: 'unknown': 1, 'off': 2, 'on': 3.

Hard disk capacity (MB). Enumeration: 'unknown': 4294967295.

Power-On Hours. Enumeration: 'unknown': -1.

A table containing the FRU information.

Information about FRU information.

Information about FRU id.

FRU board manufacturer.

FRU board product name.

FRU board serial number.

FRU board part number.

FRU borad maufacturer date.

FRU board file id.

FRU product maufacturer.

FRU product name.

FRU product serial number.

FRU product part number .

FRU product version.

FRU product asset tag. The value define as: A string of up to 48 bytes, including digits, letters, and special characters.

FRU product file id.

A table containing the FRU extend E-label.

Information about label.

Extened fru ID.

Fru extend E-label index.

format: key=value

System peak power, unit is W.

System peak power occur time, based on UTC

System average power, unit is W.

Power consume from power statistic start time, unit is kWh.

The start time of power statistic, based on UTC. the value such as (yyyy-mm-dd hh:mm:ss).

clear all power statistic, write only. Enumeration: 'clearall': 1.

Heat consume from power statistic start time, unit is kcal.

Power capping status. disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

Power capping value, the vaule is in [1, 9999].

When power capping failed, host system action. Default value is eventlog(1). Enumeration: 'eventlogAndPowerOff': 2, 'eventlog': 1.

Information about all standard PCIe device health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the standard PCIe device.

Information about PCIe device.

Information about PCIe device index.

Information about PCIe device presence. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Information about PCIe device health. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

Information about PCIe device availability. Enumeration: 'disabled': 2, 'unknown': 1, 'backup': 3, 'active': 4.

PCIe physical location.

PCIe logic function.

PCIe devicename.

PCIe device VID.

PCIe device DID.

PCIe device manufacturer.

PCIe device description.

A table containing the net card information.

Information about net card.

Information about net card index.

Net card physical location.

Net card logic function.

Net card device name.

Net card model.

NIC type define as: 8: PCIe card, 11: Mezz card, 13: NIC. Enumeration: 'mezzCard': 11, 'nic': 13, 'pcieCard': 8.

Net card name.

Net card chip model.

Net card manufacturer.

Net card chip manufacturer.

Net card driver name.

Net card driver version.

Net card firmware version.

Net card PCB version.

Net card board ID. Enumeration: 'unknown': -1.

Net card resource ownership. The value n is defined as: 1~253: CPU[n], 254: PCH, 255: PCIe Switch. Enumeration: 'pch': 254, 'pcieSwitch': 255.

Net card root port BDF.

Information about all temperature sensor health status. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'unknow': 5, 'minor': 2.

A table containing the temperature infomation.

Information about temperature.

Information about temperature index.

Information about temperature object.

Information about temperature reading,the unit is 1/10 Celsius degree. If power off, the CPU temperature cannot be readable and is set to 65535.

Information about temperature upper nonrecoverable threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about temperature upper critical threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about temperature upper minor threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about temperature lower nonrecoverable threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about temperature lower critical threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about temperature lower minor threshold,the unit is 1/10 Celsius degree,65535 represent NA.

Information about whether the system support NTP.If the system does not support NTP,then we can ignore the value returned by working the nodes of networkTimeProtocol. Enumeration: 'support': 2, 'nosupport': 1.

Enable or disable NTP. Enumeration: 'enable': 2, 'disable': 1.

Preferred NTP server IPv4 or IPv6 address. This value is right IP address or empty, the default value is empty.

Alternate DNS server IPv4 or IPv6 address. This value is right IP address or empty, the default value is empty.

Information about NTP source. Enumeration: 'auto': 2, 'manual': 1.

Information about NTP bind ip protocol. Enumeration: 'ipv4': 1, 'ipv6': 2.

Enable or disable NTP authentication. Enumeration: 'enable': 2, 'disable': 1.

Import group key.

Information about NTP Group key. Enumeration: 'notimported': 1, 'imported': 2.

The minimum poll intervals for NTP messages, in seconds to the power of two. The value range is 3 to 17. Enumeration: 'interval16s': 4, 'interval64s': 6, 'interval512s': 9, 'interval68m': 12, 'interval8s': 3, 'interval36h': 17, 'interval32s': 5, 'interval1024s': 10, 'interval256s': 8, 'interval9h': 15, 'interval2h': 13, 'interval34m': 11, 'interval4h': 14, 'interval128s': 7, 'interval18h': 16.

The maximum poll intervals for NTP messages, in seconds to the power of two. The value range is 3 to 17. Enumeration: 'interval16s': 4, 'interval64s': 6, 'interval512s': 9, 'interval68m': 12, 'interval8s': 3, 'interval36h': 17, 'interval32s': 5, 'interval1024s': 10, 'interval256s': 8, 'interval9h': 15, 'interval2h': 13, 'interval34m': 11, 'interval4h': 14, 'interval128s': 7, 'interval18h': 16.

The powerOnControl format: IP,PORT,ENABLE(eg 192.168.1.1,6999,1), maxlength is 255 characters.

Information about the authentication and encryption algorithm for SNMP V3. the format is AUTHORITYandENCRPTION: MD5andDES(1), MD5andAES(2), SHA1andDES(3), SHA1andAES(4). NOTE: the snmp will restart after this value changed. Enumeration: 'mD5andDES': 1, 'mD5andAES': 2, 'sHA1andAES': 4, 'sHA1andDES': 3.

Start upgrade firmware, The set format is: ,[effect mode], with max length 256. The format is: /PATH/FILE. The [effect mode] is an optional parameter. It only refers to upgrading iBMC firmware. The definition is as following and default is 2. 1: manually reboot later; 2: auto reboot after upgrade; In addition, This parameter is ignored in iBMC which is 2.36 and above. e.g.: /tmp/image.hpm,1. NOTE: 1.Do not power off the server or restart the iBMC during the firmware upgrade. 2.If the firmware fails to upgrade, check whether the iBMC's memory capacity is sufficient and the upgrade file is correct. 3.Upgrade BIOS firmware, system needs two minutes of preparation time. 4.Do not shut down or restart the OS during a BIOS upgrade. 5.If OS is power on,the BIOS upgrade file is uploaded to BMC and take effect when OS is power-off or reseted next time.

Information about firmware upgrading state. the value defined as: -1: upgrade not start or completed, -2: file uploading, -3: checking preUpgrade, -4: invalid URI or file not exist, -5: file upload failed, -6: file too large or memory not enough, -7: invalid upgrade package, -8: not support upgrade in current state, -9: upgrade failed, -10: The upgrade file does not match the device to be upgraded, -11: The BIOS upgrade fails because the ME status is not correct, -12: Unknown error, [0,100]:represents upgrade progress in percentage while firmware being upgrading.

Detailed results about firmware upgrade.

Owner country of current certificate, with length of 2.

Owner state of current certificate, with length of [0,64].

Owner location of current certificate, with length of [0,64].

Owner organization of current certificate, with length of [0,64].

Owner organization unit of current certificate, with length of [0,64].

Owner common name of current certificate, with length of [1,64].

Issuer country of current certificate, with length of 2.

Issuer state of current certificate, with length of [0,64].

Issuer location of current certificate, with length of [0,64].

Issuer organization of current certificate, with length of [0,64].

Issuer organization unit of current certificate, with length of [0,64].

Issuer common name of current certificate, with length of [1,64].

Start time of current certificate.

Expiration of current certificate.

Owner country of request certificate, with length of 2, contains any letters.

Owner state of request certificate, with length of [0,64], contains any digits, letters, or the symbol spaces.

Owner location of request certificate, with length of [0,64], contains any digits, letters, or the symbol spaces.

Owner organization of request certificate, with length of [0,64], contains any digits, letters, or - _ . spaces symbol.

Owner organization unit of request certificate, with length of [0,64], contains any digits, letters, or - _ . spaces symbol.

Owner common name of request certificate, with length of [1,64], contains any digits, letters, or - _ . spaces symbol.

Start to generate CSR of request certificate. Enumeration: 'csrGenerate': 1.

Acquire the CSR of request certificate. The value is empty if request csr not exist.

Import server certificate and the server certificate must be in the .pem format.

The status of generating CSR. CSR generation has not started or has successfully completed(1) A CSR is being generated (2) A CSR fails to be generated (3). Enumeration: 'failsGenerated': 3, 'beingGenerated': 2, 'notStartedOrHasSuccessfullyCompleted': 1.

Set custom certificate content and the custom certificate must be in the .pfx format.

Set custom certificate password, with max len 127.

The action of import custom certificate. Enumeration: 'customCertificateImport': 1.

A table containing the list of certificate information.

Information about certificate.

Information about certificate index.

Information about certificate type.

Owner country of current certificate, with length of 2.

Owner state of current certificate, with length of [0,64].

Owner location of current certificate, with length of [0,64].

Owner organization of current certificate, with length of [0,64].

Owner organization unit of current certificate, with length of [0,64].

Owner common name of current certificate, with length of [1,64].

Issuer country of current certificate, with length of 2.

Issuer state of current certificate, with length of [0,64].

Issuer location of current certificate, with length of [0,64].

Issuer organization of current certificate, with length of [0,64].

Issuer organization unit of current certificate, with length of [0,64].

Issuer common name of current certificate, with length of [1,64].

Start time of current certificate.

Expiration of current certificate.

Serial Number of current certificate.

Information about SD card controller manufacturer.

Information about SD card controller version.

Information about all sdcard health status. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

A table containing the sd card.

Information about sd card.

Information about sd card index.

Information about sd card presence. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Information about sd card health. Enumeration: 'major': 3, 'ok': 1, 'unknown': 6, 'absence': 5, 'critical': 4, 'minor': 2.

sd card capacity(MB).

sd card manufacturer.

sd card sn.

Presence of security module. Enumeration: 'unknown': 3, 'absence': 1, 'presence': 2.

Specification type of security module.

Specification version of security module.

Manufacturer name of security module.

Manufacturer firmware version of security module.

The enable state of syslog. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

Choose the server Identity when sending syslog. Enumeration: 'boardSN': 1, 'productAssetTag': 2, 'hostName': 3.

The level of syslog send. Default level is ok. ok:send all level message. minor:send minor and above level message. major:send major and above level message. critical:send critical level message. none:send nothing. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'none': 5, 'minor': 2.

The syslog protocol type. Default value is TCP. udp:When receiving messages using the UDP protocol. tcp:When receiving messages using the TCP protocol. tls:When receiving messages using the TCP protocol Enumeration: 'tls': 3, 'udp': 1, 'tcp': 2.

The syslog auth type. Default value is one way authentication. one way authentication:authenticate the server. mutual authentication:authenticate the server and client. Enumeration: 'one-way': 1, 'mutual': 2.

Import root certificate of the syslog server,write only. eg:/tmp/cacert.pem

Import client certificate of the syslog server,write only. eg:/tmp/client.pfx;password

A table containing the list of Syslog information.

Information about a syslog group.

Syslog Receiver state enable 2, disable 1. Enumeration: 'enable': 2, 'disable': 1.

Syslog Receiver IP addrsss. Default value is empty.

Syslog port.

The log type of syslog send. Support set/get any combination of the 3 log type(OperationLogs,SecurityLogs,EventLogs), use comma to separate them. none/all is also supported,but never use it with the 3 log types together. e.g. To set OperationLogs + SecurityLogs log type message, just set: OperationLogs,SecurityLogs To set EventLogs message, just set: EventLogs To set none level message, just set: none To set all level message, just set: all

Test the syslog. When set, the value is only 1.

A table containing the list of Syslog cert information. 1:root CA. 2:client cert.

Information about a syslog cert group.

1: The root CA of syslog server. 2: The client certificate of iBMC.

Provides information about the user (current server) of an SSL certificate.

Provides information about the issuer of an SSL certificate. The fields contained in Issued By are the same as those in Issued To.

Indicates the date when an SSL certificate starts to take effect.

Indicates the date when an SSL certificate will expire.

Indicates the serial number of an SSL certificate, used for identifying and migrating the certificate.

The file transfer URL format is: The maximum length of the URL is 1024 bytes. The parameters in the URL are described as follows: The download means download file to BMC. The upload means upload file to the destination server. The ID is the file ID, ranging from 0 to 255. The supported protocols include https, sftp, cifs, scp, and nfs. The username and password are those of the destination server. The IP can be set to an IPv4/IPv6 address or a domain name. The directory and filename are those on the destination server. Example URLs are as follows: download;0;https://root:test1234@192.168.2.13:443/data/display0.ini upload;1;sftp://root:test1234@[2001::178]/home/options0.ini The URL can contain only letters, digits, and special characters. The directory or file name cannot contain @.

Information about file transfer state. the value defined as: -1 : unknown error, -101: download unavailable, -102: file name too long, -103: failed to obtain the file length, or the file length out of MAXlength or memory, -104: set file update flag error, -105: libcurl run error, -106: upload unavailable, -107: upload file unavailable, -108: protocol not supported, -109: url format error, [0,100]:represents transfer progress in percentage while file being transfered.

A table containing the RAID controller.

Information about RAID controller.

Information about RAID controller index.

Information about RAID controller name.

Information about RAID controller type.

Information about RAID controller component name.

Information about RAID controller if support OOB management. 1: No 2: Yes Enumeration: 'yes': 2, 'no': 1.

Information about RAID controller mode. 1: None-RAID 2: RAID 255: Unknown Enumeration: 'unknown': 255, 'none-raid': 1, 'raid': 2.

Information about RAID controller health status. bit0: 1- memory correctable error bit1: 1- memory uncorrectable error bit2: 1- memory ECC error reached limit bit3: 1- NVRAM uncorrectable error other: reserved Enumeration: 'unknown': 65535, 'ok': 0.

Information about RAID controller firmware version.

Information about RAID controller NVData version.

Information about RAID controller memory size (MB). Enumeration: 'unknown': 65535.

Information about RAID controller device interface type. 1: SPI 2: SAS-3G 3: SATA-1.5G 4: SATA-3G 5: SAS-6G 6: SAS-12G 255: Unknown Enumeration: 'sas-6G': 5, 'unknown': 255, 'sata-3G': 4, 'spi': 1, 'sas-3G': 2, 'sas-12G': 6, 'sata-1-5G': 3.

Information about RAID controller SAS address.

Information about RAID controller if cache is pinned. 1: No 2: Yes 255: Unknown Enumeration: 'unknown': 255, 'yes': 2, 'no': 1.

Information about RAID controller if maintain PD fail history. 1: No 2: Yes 255: Unknown Enumeration: 'unknown': 255, 'yes': 2, 'no': 1.

Information about RAID controller DDR ECC count. Enumeration: 'unknown': 65535.

Information about RAID controller's BBU presence. 1: Absent 2: Present 255: Unknown Enumeration: 'absent': 1, 'present': 2, 'unknown': 255.

Information about RAID controller' BBU type.

Information about RAID controller's BBU health status. bit0: 1 - voltage is low bit1: 1 - need replace pack bit2: 1 - learn cycle failed bit3: 1 - learn cycle timeout bit4: 1 - pack is about to fail bit5: 1 - remaining capacity low bit6: 1 - no space for cache offload others: reserved Enumeration: 'ok': 0.

Information about the minimum strip size that RAID controller support. Enumeration: 'unknown': -1.

Information about the maximum strip size that RAID controller support. Enumeration: 'unknown': -1.

Information about the copyback state of RAID controller. 1: Unknown (read only) 2: Disabled 3: Enabled Enumeration: 'disabled': 2, 'unknown': 1, 'enabled': 3.

Information about the copyback state on SMART error of RAID controller. 1: Unknown (read only) 2: Disabled 3: Enabled Note: Set action is available only when raidControllerCopybackEnable = Enabled. Enumeration: 'disabled': 2, 'unknown': 1, 'enabled': 3.

Information about the JBOD state of RAID controller. 1: Unknown (read only) 2: Disabled 3: Enabled Enumeration: 'disabled': 2, 'unknown': 1, 'enabled': 3.

Restore RAID controller settings (write only). The argument is: 1: Restore RAID controller settings. others: invalid

Create new logical drive on this RAID controller. The arguments are seperated by semicolons; The arguments format is =;=;...;=; example: rl=r1;pd=1,2;name=example;size=100.375g;ss=256k;sc=1;rp=ra;wp=wb;iop=cio;ap=rw;dcp=enabled;init=quick; or rl=r50;pd=1,2,3,4,5,6,7,8,9;name=example;size=500g;ss=1M;sc=3;rp=ra;wp=wb;iop=cio;ap=rw;dcp=enabled;init=quick; Options and arguments: rl= The RAID level of logical drive. It is mandatory. When 'cachecade=1' is specified, RAID level 0/1 is valid. r0: RAID0 r1: RAID1 r5: RAID5 r6: RAID6 r10: RAID10 r50: RAID50 r60: RAID60 pd= The physical drives IDs which participate this logical drive. It is mandatory. name= The name of logical drive. The maximum is 15 printable ASCII characters except ';'. It is optional. size= The size of logical drive and unit can be 'm'(megabytes),'g'(gigabytes), or 't'(terabytes). It is optional and not necessary when 'cachecade=1' is specified. ss= The strip size of logical drive. The valid values are 64k,128k,256k,512k,1M. It is optional and not necessary when 'cachecade=1' is specified. sc= The span count of logical drive. The default is 1 when RAID level is RAID0/1/5/6 and 2 when RAID level is RAID10/50/60. It is optional and not necessary when 'cachecade=1' is specified. rp= The read policy of logical drive. It is optional and not necessary when 'cachecade=1' is specified. ra: Read Ahead nra: No Read Ahead wp= The write policy of logical drive. It is optional. wt: Write Through wbwithbbu: Write Back with BBU wb: Write Back iop= The IO policy of logical drive. It is optional and not necessary when 'cachecade=1' is specified. cio: Cached IO dio: Direct IO ap= The access policy of logical drive. It is optional and not necessary when 'cachecade=1' is specified. rw: Read Write ro: Read only blocked: Blocked dcp= The disk cache policy of logical drive. It is optional and not necessary when 'cachecade=1' is specified. enabled: Enable disk cache disabled: Disable disk cache default: Unchanged(Disk's default) init= The initialization type of logical drive. It is optional and not necessary when 'cachecade=1' is specified. no: No init quick: Quick init full: Full init cachecade=1 Logical drive is used for secondary cache. It is optional. It must be supported by RAID controller first. Note: Character ';' is not valid for logical drive name string because it is used as separator.

Add logical drive on array on this RAID controller. The arguments are seperated by semicolons; The arguments format is =;=;...;=; example: array=1;name=example;size=100.375g;ss=512k;rp=ra;wp=wb;iop=cio;ap=rw;dcp=enabled;init=quick; Options and arguments: array= The array on which the logical drive will be added. It is mandatory. name= The name of logical drive and maximum is 15 printable ASCII characters except ';'. It is optional. size= The size of logical drive and unit can be 'm'(megabytes),'g'(gigabytes), or 't'(terabytes). It is optional. ss= The strip size of logical drive. The valid values are 64k,128k,256k,512k,1M. It is optional. rp= The read policy of logical drive. It is optional. ra: Read Ahead nra: No Read Ahead wp= The write policy of logical drive. It is optional. wt: Write Through wbwithbbu: Write Back with BBU wb: Write Back iop= The IO policy of logical drive. It is optional. cio: Cached IO dio: Direct IO ap= The access policy of logical drive. It is optional. rw: Read Write ro: Read only blocked: Blocked dcp= The disk cache policy of logical drive. It is optional. enabled: Enable disk cache disabled: Disable disk cache default: Unchanged(Disk's default) init= The initialization type of logical drive. It is optional. no: No init quick: Quick init full: Full init Note: Character ';' is not valid for logical drive name string because it is used as separator.

Information about RAID controller driver name.

Information about RAID controller driver version

Information about RAID controller supported levels.

A table containing the logical drive created by RAID controller.

Information about logical drive.

Information about RAID controller index to which this logical drive belongs.

Information about logical drive index in current RAID controller.

Information about logical drive RAID level.

Information about logical drive state. 1: Offline 2: Partial degraded 3: Degraded 4: Optimal 255: Unknown Enumeration: 'optimal': 4, 'offline': 1, 'degraded': 3, 'partial-degraded': 2, 'unknown': 255.

Information about logical drive default read policy. 1: No read ahead 2: Read ahead 255: Unknown (read only) Note: Set action is not available when logical drive is used for secondary cache(logicalDriveIsSSCD = Yes). Enumeration: 'unknown': 255, 'read-ahead': 2, 'no-read-ahead': 1.

Information about logical drive default write policy. 1: Write through 2: Write back with BBU 3: Write back This option value is not settable when logical drive is used for secondary cache(logicalDriveIsSSCD = Yes). 255: Unknown (read only) Enumeration: 'write-through': 1, 'write-back-with-bb': 2, 'write-back': 3, 'unknown': 255.

Information about logical drive default IO policy. 1: Cached IO 2: Direct IO 255: Unknown (read only) Note: Set action is not available when logical drive is used for secondary cache(logicalDriveIsSSCD = Yes). Enumeration: 'direct-IO': 2, 'cached-IO': 1, 'unknown': 255.

Information about logical drive current read policy. 1: No read ahead 2: Read ahead 255: Unknown Enumeration: 'unknown': 255, 'read-ahead': 2, 'no-read-ahead': 1.

Information about logical drive current write policy. 1: Write Through 2: Write Back with BBU 3: Write Back 255: Unknown Enumeration: 'write-through': 1, 'write-back-with-bb': 2, 'write-back': 3, 'unknown': 255.

Information about logical drive current IO policy. 1: Cached IO 2: Direct IO 255: Unknown Enumeration: 'direct-IO': 2, 'cached-IO': 1, 'unknown': 255.

Information about logical drive span depth. Enumeration: 'unknown': 255.

Information about logical drive number of drives per span. Enumeration: 'unknown': 255.

Information about logical drive stripe size in bytes. Enumeration: 'unknown': 4294967295.

Information about logical drive stripe size in mega-bytes. Enumeration: 'unknown': 4294967295.

Information about logical drive size (MB). Enumeration: 'unknown': 4294967295.

Information about logical drive disk cache policy. 1: Disk's default 2: Enabled 3: Disabled 255: Unknown (read only) Note: Set action is not available when logical drive's participated physical drives are SSD. Enumeration: 'disabled': 3, 'unknown': 255, 'disk-default': 1, 'enabled': 2.

Information about logical drive consistency check status. 1: Stopped 2: In-progress 255: Unknown Enumeration: 'in-progress': 2, 'unknown': 255, 'stopped': 1.

Information about logical drive if it is bootable. 1: No (read only) 2: Yes 255: Unknown (read only) Note: 1. CacheCade logical drive can't be set as bootable drive. 2. Noraml logical drive(not cachecade) during offline state can be set bootable successfully, but readback value of logicalDriveBootable is still 'No' unless change the logical drive state to online. Enumeration: 'unknown': 255, 'yes': 2, 'no': 1.

Information about logical drive name. The maximum is 15 printable ASCII characters.

Information about logical drive access policy. 1: Unknown (read only) 2: Read Write 3: Read Only 4: Blocked 5: Hidden (read only) Note: Set action is not available when logical drive is used for secondary cache(logicalDriveIsSSCD = Yes). Enumeration: 'read-write': 2, 'unknown': 1, 'hidden': 5, 'read-only': 3, 'blocked': 4.

Information about logical drive init state. 1: Unknown 2: No Init 3: Quick Init 4: Full Init Enumeration: 'unknown': 1, 'no-init': 2, 'quick-init': 3, 'full-init': 4.

Information about logical drive BGI state. 1: Unknown (read only) 2: Disabled 3: Enabled Note: Set action is not available when logical drive is used for secondary cache(logicalDriveIsSSCD = Yes). Enumeration: 'disabled': 2, 'unknown': 1, 'enabled': 3.

Information about logical drive if it is used for secondary cache. 1: Unknown 2: No 3: Yes Enumeration: 'unknown': 1, 'yes': 3, 'no': 2.

Information about logical drive SSCD caching state if it is not used for secondary cache and it's participated physical drives are not SSD. 1: Unknown (read only) 2: Disabled 3: Enabled Enumeration: 'disabled': 2, 'unknown': 1, 'enabled': 3.

Information about logical drive associated logical drives IDs seperated by commas if it is used for secondary cache.

Information about logical drive dedicated hot spare physical drives IDs seperated by commas.

Delete logical drive (write only). The argument is : 1: delete others: invalid

Information about logical drive OS letter.

A table containing the disk array managed by RAID controller.

Information about logical drive.

Information about RAID controller index to which this disk array belongs.

Information about disk array index in current RAID controller.

Information about the used space in MB of disk array. Enumeration: 'unknown': 4294967295.

Information about the free space in MB of disk array. Enumeration: 'unknown': 4294967295.

Information about logical drive count in the disk array. Enumeration: 'unknown': 255.

Information about logical drive IDs in the disk array, seperated by commas.

Information about physical drive count in the disk array. Enumeration: 'unknown': 255.

Information about physical drive IDs in the disk array, seperated by commas.

Local KVM display state. disable 1, enable 2. Default value is enable(2). Enumeration: 'enable': 2, 'disable': 1.

The enable state of two-factor authentication. disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

The enable state of certificate revocation check. disable 1, enable 2. Default value is disable(1). Enumeration: 'enable': 2, 'disable': 1.

A table containing the list of root certificate information.

Information about root certificate.

root certificate subject.

root certificate issuer.

root certificate valid start data.

root certificate valid end date.

root certificate serial number.

Import root certificate,write only. eg:/tmp/cacert.pem

Information about delete root certificate. This vaule will be one of the following: (delete(1)).

A table containing the list of client certificate information.

Information about client certificate.

The client certificate finger print.

Import client certificate,write only. eg:/tmp/clientcert.pem

Information about delete client certificate. This vaule will be one of the following: (delete(1)).

Starting to export all configuration of BMC , BIOS and RAID Controller. The exported RAID Controller configurations are valid only if they are exported after the POST is complete. The input parameter is file path or URL of configuration file. Filepath e.g.: /tmp/config.xml File URL : protocol://username:password@IP:[port]/directory/filename The parameters in the URL are described as follows: The protocol must be https,sftp,cifs,scp or nfs. The username and password are those of the destination server. The directory and filename are those on the destination server.

Starting to import all configuration of BMC , BIOS and RAID Controller. The input parameter is file path or URL of configuration file. Filepath e.g.: /tmp/config.xml File URL : protocol://username:password@IP:[port]/directory/filename The parameters in the URL are described as follows: The protocol must be https,sftp,cifs,scp or nfs. The username and password are those of the destination server. The directory and filename are those on the destination server.

Query the progress of exporting/importing all configuration of BMC , BIOS and RAID Controller. Query the progress of uploading configuration file to remote host or download configuration file from remote host. The positive value means percentage of exporting/importing or uploading/downloading. The negative value(-1) means error.

Query the error information of exporting/importing all configuration of BMC , BIOS and RAID Controller. Query the error information of uploading configuration file to remote host or download configuration file from remote host. If error happened, configerrorinfo value shows the error information. If error don't happened, configerrorinfo value is null.

A table containing the net card business port information.

Information about net card business port.

Information about business port logical resource index within all net card.

Information about business port silk number within a net card.

Information about businessport belongs to which net card.

Business port link status.

Business port MAC address.

Business port BDF.

Trap sequence

Trap sensor name

Trap description

Trap severity 1 - ok, 2 - minor, 3 - major, 4 - critical. Enumeration: 'major': 3, 'critical': 4, 'ok': 1, 'minor': 2.

Trap EventCode

Trap Event Data 2

Trap Event Data 3

Trap Sever Identity

Trap location

Trap time

Huawei OEM event

General Chassis Intrusion

General Chassis Intrusion Deassert

CPU CAT error

CPU CAT error deassert

CPU thermal trip

CPU thermal trip deassert

CPU FRB1/BIST failure

CPU FRB1/BIST failure deassert

CPU configure error

CPU configure error deassert

CPU Presence

CPU Presence deassert

CPU offline

CPU offline deassert

CPU MCE occured

CPU MCE deassert

CPU VMSE link failure in mirror mode

CPU VMSE link failure in mirror mode deassert

Power Supply Fault

Power Supply Fault Deassert

Power Supply Predictive Failure

Power Supply Predictive Failure Deassert

Power Supply input lost

Power Supply input lost Deassert

AC lost or out-of-range

AC lost or out-of-range Deassert

PSU overheating. (Generated)

PSU overheating. (Cleared)

memory correctable ECC error occurred

memory correctable ECC error deassert

memory uncorrectable ECC error occurred

memory uncorrectable ECC error deassert

memory correctable ECC logging limit reached detected

memory correctable ECC logging limit reached deassert

memory presence detected

memory presence deassert

memory config error detected

memory config error deassert

memory spare detected

memory spare deassert

memory overtemperature detected

memory overtemperature deassert

Storage device presence detected

Storage device presence deassert

Storage device fault detected

Storage device fault deassert

Storage device predictive failure

Storage device predictive failure deassert

RAID array fail detected

RAID array fail deassert

RAID rebuild detected

RAID rebuild deassert

RAID rebuild aborted detected

RAID rebuild aborted deassert

System firmware hang

System firmware hang deassert

System no memory detected

System no memory detected deassert

Unrecoverable PS/2 or USB keyboard failure

Unrecoverable PS/2 or USB keyboard failure deassert

Unrecoverable video controller failure

Unrecoverable video controller failure deassert

CPU voltage mismatch

CPU voltage mismatch deassert

SEL log area is cleared

SEL almost full assert

SEL almost full deassert

System hang up/reset. For more information, see the background log

System hang up/reset deassert

PEF action

Power button pressed

PCIe card hot-swap button pressed

SAS or Harddisk backplane cable config error

SAS or Harddisk backplane cable config error deassert

system restart cause unknown

system restart cause chassis control

system restart cause power button pressed

system restart cause Watchdog control

system restart cause BMC control

system restart cause always power up

system restart cause always restore previous state

boot error, no bootable media

boot error, no bootable media deassert

boot error, Non-bootable disk in drive

boot error, Non-bootable disk in drive deassert

boot error, PXE server not found

boot error, PXE server not found deassert

boot error, Invalid boot sector

boot error, Invalid boot sector deassert

Hardware address in fault status

Hardware address in fault status deassert

Heartbeat signals between the iBMC and iBMA are lost

Heartbeat signals between the iBMC and iBMA are normal

Device installed

Device installed deassert

System Eth link down

System Eth link down deassert

Spare Device

Spare Device deassert

PCIe Error

PCIe Error deassert

fan in fault status

fan in fault status deassert

PCIe in fault status

PCIe in fault status deassert

ACPI status S0

ACPI status, S4/S5 soft-off, particular when S4/S5 state cannot be determined

watchdog overflow, no action

watchdog overflow, no action deassert

watchdog overflow, hard reset

watchdog overflow, hard reset deassert

watchdog overflow, power down

watchdog overflow, power down deassert

watchdog overflow, power cycle

watchdog overflow, power cycle deassert