FOUNDRY-BFD-STD-MIB: View SNMP OID List / Download MIB

VENDOR: BROCADE


 Home MIB: FOUNDRY-BFD-STD-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, FOUNDRY-SN-ROOT-MIB, INET-ADDRESS-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 bfdMIB 1.3.6.1.4.1.1991.3.3.1
Bidirectional Forwarding Management Information Base.
     bfdNotifications 1.3.6.1.4.1.1991.3.3.1.0
         bfdSessUp 1.3.6.1.4.1.1991.3.3.1.0.1
This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the up(2) state from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: up(1)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For the cases where a contiguous range of sessions have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical.
         bfdSessDown 1.3.6.1.4.1.1991.3.3.1.0.2
This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the down(4) or adminDown(5) states from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: down(4) or adminDown(5)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of sessions have transitioned into the down(4) or adminDown(5) states at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical.
     bfdObjects 1.3.6.1.4.1.1991.3.3.1.1
         bfdScalarObjects 1.3.6.1.4.1.1991.3.3.1.1.1
             bfdAdminStatus 1.3.6.1.4.1.1991.3.3.1.1.1.1 integer read-write
The global administrative status of BFD in this router. The value 'enabled' denotes that the BFD Process is active on at least one interface; 'disabled' disables it on all interfaces. Enumeration: 'disabled': 2, 'enabled': 1.
             bfdVersionNumber 1.3.6.1.4.1.1991.3.3.1.1.1.3 unsigned32 read-only
The current version number of the BFD protocol.
             bfdSessNotificationsEnable 1.3.6.1.4.1.1991.3.3.1.1.1.4 truthvalue read-write
If this object is set to true(1), then it enables the emission of bfdSessUp and bfdSessDown notifications; otherwise these notifications are not emitted.
         bfdSessTable 1.3.6.1.4.1.1991.3.3.1.1.2 no-access
The BFD Session Table describes the BFD sessions.
             bfdSessEntry 1.3.6.1.4.1.1991.3.3.1.1.2.1 no-access
The BFD Session Entry describes BFD session.
                 bfdSessIndex 1.3.6.1.4.1.1991.3.3.1.1.2.1.1 bfdsessindextc no-access
This object contains an index used to represent a unique BFD session on this device.
                 bfdSessApplicationId 1.3.6.1.4.1.1991.3.3.1.1.2.1.2 unsigned32 read-only
This object contains an index used to indicate a local application which owns or maintains this BFD session. For instance, the MPLS VPN process may maintain a subset of the total number of BFD sessions. This application ID provides a convenient way to segregate sessions by the applications which maintain them.
                 bfdSessDiscriminator 1.3.6.1.4.1.1991.3.3.1.1.2.1.3 unsigned32 read-only
This object specifies the local discriminator for this BFD session, used to uniquely identify it.
                 bfdSessRemoteDiscr 1.3.6.1.4.1.1991.3.3.1.1.2.1.4 unsigned32 read-only
This object specifies the session discriminator chosen by the remote system for this BFD session.
                 bfdSessUdpPort 1.3.6.1.4.1.1991.3.3.1.1.2.1.5 inetportnumber read-only
The UDP Port for BFD. The default value is the well-known value for this port.
                 bfdSessState 1.3.6.1.4.1.1991.3.3.1.1.2.1.6 integer read-only
The perceived state of the BFD session. Enumeration: 'adminDown': 1, 'down': 2, 'init': 3, 'up': 4.
                 bfdSessRemoteHeardFlag 1.3.6.1.4.1.1991.3.3.1.1.2.1.7 truthvalue read-only
This object specifies status of BFD packet reception from the remote system. Specifically, it is set to true(1) if the local system is actively receiving BFD packets from the remote system, and is set to false(0) if the local system has not received BFD packets recently (within the detection time) or if the local system is attempting to tear down the BFD session.
                 bfdSessDiag 1.3.6.1.4.1.1991.3.3.1.1.2.1.8 unsigned32 no-access
A diagnostic code specifying the local system's reason for the last transition of the session from up(1) to some other state.
                 bfdSessOperMode 1.3.6.1.4.1.1991.3.3.1.1.2.1.9 integer read-only
This object specifies current operating mode that BFD session is operating in. A value of AsyncModeWEchoFun(1) ... A value of AsynchModeWOEchoFun(2) ... A value of DemandModeWEchoFunction(3) ... A value of DemandModeWOEchoFunction(4) ... Enumeration: 'demandModeWOEchoFunction': 4, 'demandModeWEchoFunction': 3, 'asynchModeWOEchoFun': 2, 'asyncModeWEchoFun': 1.
                 bfdSessDemandModeDesiredFlag 1.3.6.1.4.1.1991.3.3.1.1.2.1.10 truthvalue read-only
This object indicates that the local system's desire to use Demand mode. Specifically, it is set to true(1) if the local system wishes to use Demand mode or false(0) if not
                 bfdSessEchoFuncModeDesiredFlag 1.3.6.1.4.1.1991.3.3.1.1.2.1.11 truthvalue read-only
This object indicates that the local system's desire to use Echo mode. Specifically, it is set to true(1) if the local system wishes to use Echo mode or false(0) if not
                 bfdSessControlPlanIndepFlag 1.3.6.1.4.1.1991.3.3.1.1.2.1.12 truthvalue read-only
This object indicates that the local system's ability to continue to function through a disruption of the control plane. Specifically, it is set to true(1) if the local system BFD implementation is independent of the control plane. Otherwise, the value is set to false(0)
                 bfdSessAddrType 1.3.6.1.4.1.1991.3.3.1.1.2.1.13 inetaddresstype read-only
This object specifies IP address of the interface associated with this BFD session. Only values unknown(0), ipv4(1) or ipv6(2) have to be supported. A value of unknown(0) is allowed only when the outgoing interface is of type point-to-point, or when the BFD session is not associated with a specific interface. If any other unsupported values are attempted in a set operation, the agent MUST return an inconsistentValue error.
                 bfdSessAddr 1.3.6.1.4.1.1991.3.3.1.1.2.1.14 inetaddress read-only
This object specifies IP address of the interface associated with this BFD session. It can also be used to enabled BFD on a specific interface. The value is set to zero when BFD session is not associated with a specific interface.
                 bfdSessDesiredMinTxInterval 1.3.6.1.4.1.1991.3.3.1.1.2.1.15 bfdinterval read-only
This object specifies the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets.
                 bfdSessReqMinRxInterval 1.3.6.1.4.1.1991.3.3.1.1.2.1.16 bfdinterval read-only
This object specifies the minimum interval, in microseconds, between received BFD Control packets the local system is capable of supporting.
                 bfdSessReqMinEchoRxInterval 1.3.6.1.4.1.1991.3.3.1.1.2.1.17 bfdinterval read-only
This object specifies the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting.
                 bfdSessDetectMult 1.3.6.1.4.1.1991.3.3.1.1.2.1.18 unsigned32 read-only
This object specifies the Detect time multiplier.
                 bfdSessStorType 1.3.6.1.4.1.1991.3.3.1.1.2.1.19 storagetype read-only
This variable indicates the storage type for this object. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
                 bfdSessRowStatus 1.3.6.1.4.1.1991.3.3.1.1.2.1.20 rowstatus read-only
This variable is used to create, modify, and/or delete a row in this table. When a row in this table has a row in the active(1) state, no objects in this row can be modified except the bfdSessRowStatus and bfdSessStorageType.
                 bfdSessAuthPresFlag 1.3.6.1.4.1.1991.3.3.1.1.2.1.21 truthvalue read-only
This object indicates that the local system's desire to use Authentication. Specifically, it is set to true(1) if the local system wishes the session to be authenticated or false(0) if not
                 bfdSessAuthenticationType 1.3.6.1.4.1.1991.3.3.1.1.2.1.22 integer read-only
The Authentication Type used for this BFD session. This field is valid only when the Authentication Present bit is set Enumeration: 'meticulousKeyedMD5': 3, 'keyedMD5': 2, 'simplePassword': 1, 'keyedSHA1': 4, 'meticulousKeyedSHA1': 5.
         bfdSessPerfTable 1.3.6.1.4.1.1991.3.3.1.1.3 no-access
This table specifies BFD Session performance counters.
             bfdSessPerfEntry 1.3.6.1.4.1.1991.3.3.1.1.3.1 no-access
An entry in this table is created by a BFD-enabled node for every BFD Session. bfdCounterDiscontinuityTime is used to indicate potential discontinuity for all counter objects in this table.
                 bfdSessPerfPktIn 1.3.6.1.4.1.1991.3.3.1.1.3.1.1 counter32 read-only
The total number of BFD messages received for this BFD session.
                 bfdSessPerfPktOut 1.3.6.1.4.1.1991.3.3.1.1.3.1.2 counter32 read-only
The total number of BFD messages sent for this BFD session.
                 bfdSessPerfUpTime 1.3.6.1.4.1.1991.3.3.1.1.3.1.3 timestamp read-only
The value of sysUpTime on the most recent occasion at which the session came up. If no such up event exists this object contains a zero value.
                 bfdSessPerfLastSessDownTime 1.3.6.1.4.1.1991.3.3.1.1.3.1.4 timestamp read-only
The value of sysUpTime on the most recent occasion at which the last time communication was lost with the neighbor. If no such down event exist this object contains a zero value.
                 bfdSessPerfLastCommLostDiag 1.3.6.1.4.1.1991.3.3.1.1.3.1.5 bfddiag read-only
The BFD diag code for the last time communication was lost with the neighbor. If no such down event exists this object contains a zero value.
                 bfdSessPerfSessUpCount 1.3.6.1.4.1.1991.3.3.1.1.3.1.6 counter32 read-only
The number of times this session has gone into the Up state since the router last rebooted.
                 bfdSessPerfDiscTime 1.3.6.1.4.1.1991.3.3.1.1.3.1.7 timestamp read-only
The value of sysUpTime on the most recent occasion at which any one or more of the session counters suffered a discontinuity. The relevant counters are the specific instances associated with this BFD session of any Counter32 object contained in the BfdSessPerfTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
                 bfdSessPerfPktInHC 1.3.6.1.4.1.1991.3.3.1.1.3.1.8 counter64 read-only
This value represents the total number of BFD messages received for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktInHC is supported according to the rules spelled out in RFC2863.
                 bfdSessPerfPktOutHC 1.3.6.1.4.1.1991.3.3.1.1.3.1.9 counter64 read-only
This value represents the total number of total number of BFD messages transmitted for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktOutHC is supported according to the rules spelled out in RFC2863.
         bfdSessMapTable 1.3.6.1.4.1.1991.3.3.1.1.4 no-access
The BFD Session Mapping Table maps the complex indexing of the BFD sessions to the flat BFDIndex used in the BfdSessionTable. Implementors need to be aware that if the value of the bfdSessAddr (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
             bfdSessMapEntry 1.3.6.1.4.1.1991.3.3.1.1.4.1 no-access
The BFD Session Entry describes BFD session that is mapped to this index. Implementors need to be aware that if the value of the mplsInSegmentMapLabelPtrIndex (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
                 bfdSessMapBfdIndex 1.3.6.1.4.1.1991.3.3.1.1.4.1.1 bfdsessindextc read-only
This object specifies the BfdIndex referred to by the indexes of this row. In essence, a mapping is provided between these indexes and the BfdSessTable.
     bfdConformance 1.3.6.1.4.1.1991.3.3.1.3
         bfdGroups 1.3.6.1.4.1.1991.3.3.1.3.1
             bfdSessionGroup 1.3.6.1.4.1.1991.3.3.1.3.1.1
Collection of objects needed for BFD sessions.
             bfdSessionPerfGroup 1.3.6.1.4.1.1991.3.3.1.3.1.2
Collection of objects needed to monitor the performance of BFD sessions.
             bfdSessionPerfHCGroup 1.3.6.1.4.1.1991.3.3.1.3.1.3
Collection of objects needed to monitor the performance of BFD sessions for which the values of bfdSessPerfPktIn, bfdSessPerfPktOut wrap around too quickly.
             bfdNotificationGroup 1.3.6.1.4.1.1991.3.3.1.3.1.4
Set of notifications implemented in this module.
         bfdCompliances 1.3.6.1.4.1.1991.3.3.1.3.2
             bfdModuleFullCompliance 1.3.6.1.4.1.1991.3.3.1.3.2.1
Compliance statement for agents that provide full support for BFD-MIB. Such devices can then be monitored and also be configured using this MIB module.