DGS-3700-12-L2MGMT-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK


 Home MIB: DGS-3700-12-L2MGMT-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 swL2MgmtMIB 1.3.6.1.4.1.171.11.102.1.1.2
The Structure of Layer 2 Network Management Information.
     swL2DevMgmt 1.3.6.1.4.1.171.11.102.1.1.2.1
         swL2DevInfo 1.3.6.1.4.1.171.11.102.1.1.2.1.1
             swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.102.1.1.2.1.1.1 integer read-only
The number of ports within this switch. This value is the sum of the ports within this switch.
             swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.102.1.1.2.1.1.2 integer read-only
The number of ports in this switch connected to the segment or the end stations.
             swDevInfoFrontPanelLedStatus 1.3.6.1.4.1.171.11.102.1.1.2.1.1.4 octet string read-only
This object is a set of system LED indications. The first four octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
         swL2DevCtrl 1.3.6.1.4.1.171.11.102.1.1.2.1.2
             swL2DevCtrlStpState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.1 integer read-write
This object can enable or disable the spanning tree algorithm during the runtime of the system. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.102.1.1.2.1.2.2 integer read-write
This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlSnmpTrapState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.5 integer read-write
This object controls the SNMP trap status. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.102.1.1.2.1.2.6 integer read-write
When the object is set to active, all statistical counters will be cleared. If set to normal, no action. Enumeration: 'active': 2, 'normal': 1.
             swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.102.1.1.2.1.2.7 vlanid read-write
Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
             swL2MACNotifyState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.8 integer read-write
This object can enable or disable MAC Notification. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.102.1.1.2.1.2.9 integer read-write
This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .
             swL2MACNotifyInterval 1.3.6.1.4.1.171.11.102.1.1.2.1.2.10 integer read-write
This object indicates the time interval, in seconds, which will trigger MAC notification messages.
             swL2DevCtrlTelnet 1.3.6.1.4.1.171.11.102.1.1.2.1.2.14
                   swL2DevCtrlTelnetState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.14.1 integer read-write
This object controls the Telnet status. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2DevCtrlTelnetTcpPort 1.3.6.1.4.1.171.11.102.1.1.2.1.2.14.2 integer read-write
This object designates TCP ports. When Telnet is disabled, this object is not accessible.
             swL2DevCtrlManagementVlanId 1.3.6.1.4.1.171.11.102.1.1.2.1.2.16 vlanid read-write
This object controls which previously created VLANs are included in the System IP Interface.
             swL2DevCtrlWeb 1.3.6.1.4.1.171.11.102.1.1.2.1.2.17
                   swL2DevCtrlWebState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.17.1 integer read-write
This object controls the Web status. Enumeration: 'disabled': 2, 'enabled': 1.
                   swL2DevCtrlWebTcpPort 1.3.6.1.4.1.171.11.102.1.1.2.1.2.17.2 integer read-write
This object designates TCP ports. When Web is disabled, this object is not accessible.
             swL2DevCtrlLLDPState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.18 integer read-write
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlLLDPForwardMessageState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.19 integer read-write
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlIpAutoconfig 1.3.6.1.4.1.171.11.102.1.1.2.1.2.20 integer read-write
This object controls the IP auto configuration state. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlCFM 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21
                   swL2DevCtrlCFMState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.1 integer read-write
This object indicates the CFM global state. Enumeration: 'disabled': 2, 'enabled': 1.
                   swL2DevCtrlCFMPortTable 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2 no-access
A table containing CFM state of speicified ports.
                       swL2DevCtrlCFMPortEntry 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1 no-access
The entry of CFM state on speicified ports.
                           swL2DevCtrlCFMPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1.1 integer no-access
This object indicates the port-num.
                           swL2DevCtrlCFMPortState 1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1.2 integer read-write
This object indicates the CFM state on per-port. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2DevAlarm 1.3.6.1.4.1.171.11.102.1.1.2.1.3
             swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.102.1.1.2.1.3.1 integer read-write
When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.102.1.1.2.1.3.2 integer read-write
This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.102.1.1.2.1.3.3 integer read-write
This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2VLANMgmt 1.3.6.1.4.1.171.11.102.1.1.2.2
         swL2VlanStaticTable 1.3.6.1.4.1.171.11.102.1.1.2.2.1 no-access
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
             swL2VlanStaticEntry 1.3.6.1.4.1.171.11.102.1.1.2.2.1.1 no-access
Static information for a VLAN configured into the device by (local or network) management.
                 swL2VlanIndex 1.3.6.1.4.1.171.11.102.1.1.2.2.1.1.1 vlanid no-access
The VLAN-ID or other identifier referring to this VLAN.
                 swL2VLANAdvertisement 1.3.6.1.4.1.171.11.102.1.1.2.2.1.1.2 integer read-write
This object indicates if the advertisement is active or not. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2PVIDAutoAssignmentState 1.3.6.1.4.1.171.11.102.1.1.2.2.2 integer read-write
This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2VlanPortInfoTable 1.3.6.1.4.1.171.11.102.1.1.2.2.3 no-access
A table containing vlan and port role information of each port.
             swL2VlanPortInfoEntry 1.3.6.1.4.1.171.11.102.1.1.2.2.3.1 no-access
The table entry of vlan port information.
                 swL2VlanPortInfoPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.1 integer read-only
The port index.
                 swL2VlanPortInfoVid 1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.2 integer read-only
The VLAN-ID assigned to a special port
                 swL2VlanPortInfoPortRole 1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.3 integer read-only
The port role of a special port.when none,it means this port is not belong to the vlan. Enumeration: 'untagged': 2, 'none': 1, 'dynamic': 4, 'tagged': 3, 'forbidden': 5.
         swL2NniGvrpBpduAddress 1.3.6.1.4.1.171.11.102.1.1.2.2.7 integer read-write
Specifies the GVRP's BPDU MAC address of NNI port In Q-in_Q status. Enumeration: 'dot1d': 1, 'dot1ad': 2.
     swL2PortMgmt 1.3.6.1.4.1.171.11.102.1.1.2.3
         swL2PortInfoTable 1.3.6.1.4.1.171.11.102.1.1.2.3.1 no-access
A table that contains information about every port.
             swL2PortInfoEntry 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1 no-access
A list of information for each port of the device.
                 swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortInfoMediumType 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.2 integer read-only
Indicates medium type of the port number. Enumeration: 'copper': 1, 'fiber': 2.
                 swL2PortInfoUnitID 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.3 integer read-only
Indicates ID of the unit in the system
                 swL2PortInfoType 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.4 integer read-only
This object indicates the connector type of this port. Enumeration: 'portType-100Base-X': 3, 'portType-10GBase-R': 6, 'portType-none': 0, 'portType-100Base-T': 2, 'portType-user-last': 10, 'portType-SIO': 8, 'portType-1000Base-T': 4, 'portType-1000Base-X': 5, 'portType-module-empty': 9, 'portType-10GBase-CX4': 7.
                 swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.5 integer read-only
This object indicates the port link status. Enumeration: 'link-fail': 3, 'other': 1, 'link-pass': 2.
                 swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.6 integer read-only
This object indicates the port speed and duplex mode. Enumeration: 'half-10Mbps-backp': 3, 'half-100Mbps-backp': 7, 'full-100Mbps-none': 6, 'half-10Gigabps-none': 16, 'err-disabled': 18, 'full-100Mbps-8023x': 5, 'half-1Gigabps-backp': 11, 'full-1Gigabps-none': 10, 'full-10Mbps-8023x': 1, 'full-10Gigabps-8023x': 13, 'half-100Mbps-none': 8, 'full-10Gigabps-none': 14, 'half-10Mbps-none': 4, 'half-1Gigabps-none': 12, 'full-10Mbps-none': 2, 'link-down': 0, 'half-10Gigabps-8023x': 15, 'full-1Gigabps-8023x': 9, 'empty': 17.
                 swL2PortInfoErrorDisabled 1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.8 integer read-only
This object indicates the blocking type of this port. Enumeration: 'ctp-lbd': 4, 'none': 0, 'unknow': 3, 'storm': 1, 'ddm': 5.
         swL2PortCtrlTable 1.3.6.1.4.1.171.11.102.1.1.2.3.2 no-access
A table that contains control information about every port.
             swL2PortCtrlEntry 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1 no-access
A list of control information for each port of the device.
                 swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCtrlMediumType 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.2 integer read-only
Indicates medium type of the port number. Enumeration: 'copper': 1, 'fiber': 2.
                 swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.3 integer read-only
Indicates ID of the unit in the device
                 swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.4 integer read-write
This object decides if the port is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.5 integer read-write
Chose the port speed, duplex mode, and N-Way function mode. Enumeration: 'nway-disabled-10Mbps-Full': 4, 'nway-disabled-1Gigabps-Full-master': 9, 'nway-enabled': 2, 'nway-disabled-1Gigabps-Full': 8, 'nway-disabled-1Gigabps-Full-slave': 10, 'other': 1, 'nway-disabled-100Mbps-Full': 6, 'nway-disabled-1Gigabps-Half': 7, 'nway-disabled-10Mbps-Half': 3, 'nway-disabled-100Mbps-Half': 5.
                 swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.6 integer read-write
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlLearningState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.7 integer read-write
This object decides if the port is locked or not. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.8 integer read-write
This object sets each port's MAC notification state. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlMDIXState 1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.10 integer read-write
This object configures the MDIX setting of the port. Enumeration: 'auto': 1, 'cross': 3, 'normal': 2.
         swL2PortCtrlJumboFrame 1.3.6.1.4.1.171.11.102.1.1.2.3.3 integer read-write
This object configures the switch's jumbo frame settings. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2PortCtrlJumboFrameMaxSize 1.3.6.1.4.1.171.11.102.1.1.2.3.4 integer read-only
This object describes how many bytes the max jumbo frame is.
         swL2PortCounterCtrlTable 1.3.6.1.4.1.171.11.102.1.1.2.3.6 no-access
A table that used to clear counter information about every port.
             swL2PortCounterCtrlEntry 1.3.6.1.4.1.171.11.102.1.1.2.3.6.1 no-access
A list of entry used to clear counter information for each port of the device.
                 swL2PortCounterCtrlPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.3.6.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCounterClearCtrl 1.3.6.1.4.1.171.11.102.1.1.2.3.6.1.2 integer read-write
This object indicates if to clear the counters for each port of the device or not. Enumeration: 'start': 2, 'other': 1.
         swL2PortErrTable 1.3.6.1.4.1.171.11.102.1.1.2.3.7 no-access
A table that contains error information for each port.
             swL2PortErrEntry 1.3.6.1.4.1.171.11.102.1.1.2.3.7.1 no-access
A list of information regarding port errors on the device.
                 swL2PortErrPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module).
                 swL2PortErrPortState 1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.2 integer read-only
This object indicates the port state is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.
                 swL2PortErrPortConnStatus 1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.3 integer read-only
This object indicates whether the PortStatus is err-disabled or not. Enumeration: 'other': 1, 'err-disabled': 2.
                 swL2PortErrPortReason 1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.4 integer read-only
This object describes if the reason for the port error is STP LBD or Storm control. Enumeration: 'ctp-lbd': 3, 'ddm': 4, 'storm-control': 2.
     swL2DhcpRelayMgmt 1.3.6.1.4.1.171.11.102.1.1.2.8
     swL2TrunkMgmt 1.3.6.1.4.1.171.11.102.1.1.2.9
         swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.102.1.1.2.9.1 integer read-only
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
         swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.102.1.1.2.9.2 integer read-only
Current active number of entries in the trunk configuration table.
         swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.102.1.1.2.9.3 no-access
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1 no-access
A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkIndex 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.1 integer read-only
The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
                 swL2TrunkMasterPort 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.3 integer read-only
The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
                 swL2TrunkMember 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.4 portlist read-only
Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
                 swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.5 integer read-only
The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
                 swL2TrunkType 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.6 integer read-only
This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group . Enumeration: 'lacp': 3, 'other': 1, 'static': 2.
                 swL2TrunkState 1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.7 rowstatus read-only
This object indicates the status of this entry.
         swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.102.1.1.2.9.4 integer read-write
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. Enumeration: 'ip-source': 5, 'mac-destination': 3, 'mac-source': 2, 'mac-source-dest': 4, 'ip-source-dest': 7, 'ip-destination': 6, 'other': 1.
         swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.102.1.1.2.9.5 no-access
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.102.1.1.2.9.5.1 no-access
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.9.5.1.1 integer read-only
The index of logical port LACP.
                 swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.102.1.1.2.9.5.1.2 integer read-write
The state of logical port LACP. Enumeration: 'active': 1, 'passive': 2.
     swL2MirrorMgmt 1.3.6.1.4.1.171.11.102.1.1.2.10
           swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.102.1.1.2.10.1 integer read-write
This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
           swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.102.1.1.2.10.2 portlist read-write
This represents the port where ingress packets will be sniffed.
           swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.102.1.1.2.10.3 portlist read-write
This represents the port where egress packets will be sniffed.
           swL2MirrorPortState 1.3.6.1.4.1.171.11.102.1.1.2.10.4 integer read-write
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.102.1.1.2.14
           swL2TrafficSegTable 1.3.6.1.4.1.171.11.102.1.1.2.14.1 no-access
This table specifies that the port can just forward traffic to the specific port list.
               swL2TrafficSegEntry 1.3.6.1.4.1.171.11.102.1.1.2.14.1.1 no-access
A list of information which specifies the port with its traffic forwarding list.
                   swL2TrafficSegPort 1.3.6.1.4.1.171.11.102.1.1.2.14.1.1.1 integer read-only
The port number of the logical port.
                   swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.102.1.1.2.14.1.1.2 portlist read-write
The port list to which the specific port can forward traffic.
     swL2MulticastFilterMode 1.3.6.1.4.1.171.11.102.1.1.2.17
           swL2MulticastFilterModeVlanTable 1.3.6.1.4.1.171.11.102.1.1.2.17.1 no-access
A table that contains information about VLAN multicast filter mode.
               swL2MulticastFilterModeVlanEntry 1.3.6.1.4.1.171.11.102.1.1.2.17.1.1 no-access
A list of multicast filter mode information for each VLAN.
                   swL2MulticastFilterVid 1.3.6.1.4.1.171.11.102.1.1.2.17.1.1.1 integer read-only
Indicates VID for each VLAN.
                   swL2MulticastFilterVlanMode 1.3.6.1.4.1.171.11.102.1.1.2.17.1.1.2 integer read-write
Specifies multicast filter mode for each VLAN. Enumeration: 'forward-unregistered-groups': 2, 'forward-all-groups': 1, 'filter-unregistered-groups': 3.
     swL2LoopDetectMgmt 1.3.6.1.4.1.171.11.102.1.1.2.18
           swL2LoopDetectCtrl 1.3.6.1.4.1.171.11.102.1.1.2.18.1
               swL2LoopDetectAdminState 1.3.6.1.4.1.171.11.102.1.1.2.18.1.1 integer read-write
This object indicates the loopback detection status for the system. Enumeration: 'disabled': 2, 'enabled': 1.
               swL2LoopDetectInterval 1.3.6.1.4.1.171.11.102.1.1.2.18.1.2 integer read-write
This object indicates the interval value, the range is from 1 to 32767 seconds.
               swL2LoopDetectRecoverTime 1.3.6.1.4.1.171.11.102.1.1.2.18.1.3 integer read-write
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
               swL2LoopDetectMode 1.3.6.1.4.1.171.11.102.1.1.2.18.1.4 integer read-write
This object indicates the loopback detection mode for the system. Enumeration: 'port-based': 2, 'vlan-based': 1.
               swL2LoopDetectTrapMode 1.3.6.1.4.1.171.11.102.1.1.2.18.1.5 integer read-write
This object indicates the loopback detection trap mode for the system. Enumeration: 'loop-detected': 2, 'loop-cleared': 3, 'none': 1, 'both': 4.
           swL2LoopDetectPortMgmt 1.3.6.1.4.1.171.11.102.1.1.2.18.2
               swL2LoopDetectPortTable 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1 no-access
The table specifies the loopback detection function specified by port.
                   swL2LoopDetectPortEntry 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1 no-access
The table specifies the loopback detection function specified by port.
                       swL2LoopDetectPortIndex 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.1 integer read-only
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
                       swL2LoopDetectPortState 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.2 integer read-write
This object indicates the loopback detection function state on the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       swL2LoopDetectPortLoopVLAN 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.3 displaystring read-only
This object indicates the VLAN list that has detected a loopback.
                       swL2LoopDetectPortLoopStatus 1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.4 integer read-only
This object indicates the port status. Enumeration: 'none': 4, 'error': 3, 'loop': 2, 'normal': 1.
     swL2DhcpLocalRelayMgmt 1.3.6.1.4.1.171.11.102.1.1.2.24
           swL2DhcpLocalRelayState 1.3.6.1.4.1.171.11.102.1.1.2.24.1 integer read-write
This object indicates the status of the DHCP local relay function of the switch. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
           swL2DhcpLocalRelayVLANTable 1.3.6.1.4.1.171.11.102.1.1.2.24.2 no-access
This table is used to manage the DHCP local relay status for each VLAN.
               swL2DhcpLocalRelayVLANEntry 1.3.6.1.4.1.171.11.102.1.1.2.24.2.1 no-access
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
                   swL2DhcpLocalRelayVLANID 1.3.6.1.4.1.171.11.102.1.1.2.24.2.1.1 integer read-only
This object shows the VIDs of the current VLANS in the switch.
                   swL2DhcpLocalRelayVLANState 1.3.6.1.4.1.171.11.102.1.1.2.24.2.1.2 integer read-write
This object indicates the status of the DHCP relay function of the VLAN. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.102.1.1.2.100
             swL2Notify 1.3.6.1.4.1.171.11.102.1.1.2.100.1
                 swL2NotifyMgmt 1.3.6.1.4.1.171.11.102.1.1.2.100.1.1
                 swL2NotifyPrefix 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2
                     swL2NotifFirmware 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0
                         swL2macNotification 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0.1
This trap indicates the MAC addresses variation in address table .
                         swL2PortLoopOccurred 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0.3
The trap is sent when a Port loop occurs.
                         swL2PortLoopRestart 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0.4
The trap is sent when a Port loop restarts after the interval time.
                         swL2VlanLoopOccurred 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0.5
The trap is sent when a Port with a VID loop occurs.
                         swL2VlanLoopRestart 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.0.6
The trap is sent when a Port with a VID loop restarts after the interval time.
                     swl2NotificationBidings 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.1
                         swL2macNotifyInfo 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.1.1 octet string read-only
This object indicates the last time reboot information.
                         swL2VlanLoopDetectVID 1.3.6.1.4.1.171.11.102.1.1.2.100.1.2.1.3 integer no-access
This object indicates the VID that detected a loopback.