DES3528P-L2MGMT-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK


 Home MIB: DES3528P-L2MGMT-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 swL2MgmtMIB 1.3.6.1.4.1.171.11.105.2.2
The Structure of Layer 2 Network Management Information.
     swL2DevMgmt 1.3.6.1.4.1.171.11.105.2.2.1
         swL2DevInfo 1.3.6.1.4.1.171.11.105.2.2.1.1
             swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.105.2.2.1.1.1 integer read-only
The number of ports within this switch. This value is the sum of the ports within this switch.
             swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.105.2.2.1.1.2 integer read-only
The number of ports in this switch connected to the segment or the end stations.
             swDevInfoFrontPanelLedStatus 1.3.6.1.4.1.171.11.105.2.2.1.1.4 octet string read-only
This object is a set of system LED indications. The first five octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
         swL2DevCtrl 1.3.6.1.4.1.171.11.105.2.2.1.2
             swL2DevCtrlStpState 1.3.6.1.4.1.171.11.105.2.2.1.2.1 integer read-write
This object can enable or disable the spanning tree algorithm during the runtime of the system. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.105.2.2.1.2.2 integer read-write
This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlIGMPSnoopingMcstRTOnly 1.3.6.1.4.1.171.11.105.2.2.1.2.3 integer read-write
This object controls IGMP snooping forward multicast routing only state. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlSnmpTrapState 1.3.6.1.4.1.171.11.105.2.2.1.2.5 integer read-write
This object controls the SNMP trap status. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.105.2.2.1.2.6 integer read-write
When the object is set to active, all statistical counters will be cleared. If set to normal, no action. Enumeration: 'active': 2, 'normal': 1.
             swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.105.2.2.1.2.7 vlanid read-write
Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
             swL2MACNotifyState 1.3.6.1.4.1.171.11.105.2.2.1.2.8 integer read-write
This object can enable or disable MAC Notification. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.105.2.2.1.2.9 integer read-write
This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .
             swL2MACNotifyInterval 1.3.6.1.4.1.171.11.105.2.2.1.2.10 integer read-write
This object indicates the time interval, in seconds, which will trigger MAC notification messages.
             swL2DevCtrlAsymVlanState 1.3.6.1.4.1.171.11.105.2.2.1.2.13 integer read-write
This object enables or disables asymmetric VLANs during the runtime of the system. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlTelnet 1.3.6.1.4.1.171.11.105.2.2.1.2.14
                   swL2DevCtrlTelnetState 1.3.6.1.4.1.171.11.105.2.2.1.2.14.1 integer read-write
This object controls the Telnet status. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2DevCtrlTelnetTcpPort 1.3.6.1.4.1.171.11.105.2.2.1.2.14.2 integer read-write
This object designates TCP ports. When Telnet is disabled, this object is not accessible.
             swL2DevCtrlManagementVlanId 1.3.6.1.4.1.171.11.105.2.2.1.2.16 vlanid read-write
This object controls which previously created VLANs are included in the System IP Interface.
             swL2DevCtrlWeb 1.3.6.1.4.1.171.11.105.2.2.1.2.17
                   swL2DevCtrlWebState 1.3.6.1.4.1.171.11.105.2.2.1.2.17.1 integer read-write
This object controls the Web status. Enumeration: 'disabled': 2, 'enabled': 1.
                   swL2DevCtrlWebTcpPort 1.3.6.1.4.1.171.11.105.2.2.1.2.17.2 integer read-write
This object designates TCP ports. When Web is disabled, this object is not accessible.
             swL2DevCtrlLLDPState 1.3.6.1.4.1.171.11.105.2.2.1.2.18 integer read-write
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlLLDPForwardMessageState 1.3.6.1.4.1.171.11.105.2.2.1.2.19 integer read-write
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlIpAutoconfig 1.3.6.1.4.1.171.11.105.2.2.1.2.20 integer read-write
This object controls the IP auto configuration state. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlCFM 1.3.6.1.4.1.171.11.105.2.2.1.2.21
                   swL2DevCtrlCFMState 1.3.6.1.4.1.171.11.105.2.2.1.2.21.1 integer read-write
This object indicates the CFM global state. Enumeration: 'disabled': 2, 'enabled': 1.
                   swL2DevCtrlCFMPortTable 1.3.6.1.4.1.171.11.105.2.2.1.2.21.2 no-access
A table containing CFM state of speicified ports.
                       swL2DevCtrlCFMPortEntry 1.3.6.1.4.1.171.11.105.2.2.1.2.21.2.1 no-access
The entry of CFM state on speicified ports.
                           swL2DevCtrlCFMPortIndex 1.3.6.1.4.1.171.11.105.2.2.1.2.21.2.1.1 integer no-access
This object indicates the port-num.
                           swL2DevCtrlCFMPortState 1.3.6.1.4.1.171.11.105.2.2.1.2.21.2.1.2 integer read-write
This object indicates the CFM state on per-port. Enumeration: 'disabled': 2, 'enabled': 1.
             swL2DevCtrlVLANTrunkState 1.3.6.1.4.1.171.11.105.2.2.1.2.22 integer read-write
This indicates the global state of the VLAN trunking feature of the device. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2DevAlarm 1.3.6.1.4.1.171.11.105.2.2.1.3
             swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.105.2.2.1.3.1 integer read-write
When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.105.2.2.1.3.2 integer read-write
This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.105.2.2.1.3.3 integer read-write
This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2VLANMgmt 1.3.6.1.4.1.171.11.105.2.2.2
         swL2VlanStaticTable 1.3.6.1.4.1.171.11.105.2.2.2.1 no-access
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
             swL2VlanStaticEntry 1.3.6.1.4.1.171.11.105.2.2.2.1.1 no-access
Static information for a VLAN configured into the device by (local or network) management.
                 swL2VlanIndex 1.3.6.1.4.1.171.11.105.2.2.2.1.1.1 vlanid no-access
The VLAN-ID or other identifier referring to this VLAN.
                 swL2VLANAdvertisement 1.3.6.1.4.1.171.11.105.2.2.2.1.1.2 integer read-write
This object indicates if the advertisement is active or not. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2PVIDAutoAssignmentState 1.3.6.1.4.1.171.11.105.2.2.2.2 integer read-write
This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'. Enumeration: 'disabled': 2, 'enabled': 1.
         swL2VlanPortInfoTable 1.3.6.1.4.1.171.11.105.2.2.2.3 no-access
A table containing vlan and port role information of each port.
             swL2VlanPortInfoEntry 1.3.6.1.4.1.171.11.105.2.2.2.3.1 no-access
The table entry of vlan port information.
                 swL2VlanPortInfoPortIndex 1.3.6.1.4.1.171.11.105.2.2.2.3.1.1 integer read-only
The port index.
                 swL2VlanPortInfoVid 1.3.6.1.4.1.171.11.105.2.2.2.3.1.2 integer read-only
The VLAN-ID assigned to a special port
                 swL2VlanPortInfoPortRole 1.3.6.1.4.1.171.11.105.2.2.2.3.1.3 integer read-only
The port role of a special port.when none,it means this port is not belong to the vlan. Enumeration: 'untagged': 2, 'none': 1, 'dynamic': 4, 'tagged': 3, 'forbidden': 5.
         swL2NniGvrpBpduAddress 1.3.6.1.4.1.171.11.105.2.2.2.6 integer read-write
Specifies the GVRP's BPDU MAC address of NNI port In Q-in_Q status. Enumeration: 'dot1d': 1, 'dot1ad': 2.
     swL2PortMgmt 1.3.6.1.4.1.171.11.105.2.2.3
         swL2PortInfoTable 1.3.6.1.4.1.171.11.105.2.2.3.1 no-access
A table that contains information about every port.
             swL2PortInfoEntry 1.3.6.1.4.1.171.11.105.2.2.3.1.1 no-access
A list of information for each port of the device.
                 swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.105.2.2.3.1.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortInfoMediumType 1.3.6.1.4.1.171.11.105.2.2.3.1.1.2 integer read-only
Indicates medium type of the port number. Enumeration: 'copper': 1, 'fiber': 2.
                 swL2PortInfoUnitID 1.3.6.1.4.1.171.11.105.2.2.3.1.1.3 integer read-only
Indicates ID of the unit in the system
                 swL2PortInfoType 1.3.6.1.4.1.171.11.105.2.2.3.1.1.4 integer read-only
This object indicates the connector type of this port. Enumeration: 'portType-100Base-X': 3, 'portType-10GBase-R': 6, 'portType-none': 0, 'portType-100Base-T': 2, 'portType-user-last': 10, 'portType-SIO': 8, 'portType-1000Base-T': 4, 'portType-1000Base-X': 5, 'portType-module-empty': 9, 'portType-10GBase-CX4': 7.
                 swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.105.2.2.3.1.1.5 integer read-only
This object indicates the port link status. Enumeration: 'link-fail': 3, 'other': 1, 'link-pass': 2.
                 swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.105.2.2.3.1.1.6 integer read-only
This object indicates the port speed and duplex mode. Enumeration: 'half-10Mbps-backp': 3, 'half-100Mbps-backp': 7, 'full-100Mbps-none': 6, 'half-10Gigabps-none': 16, 'err-disabled': 18, 'full-100Mbps-8023x': 5, 'half-1Gigabps-backp': 11, 'full-1Gigabps-none': 10, 'full-10Mbps-8023x': 1, 'full-10Gigabps-8023x': 13, 'half-100Mbps-none': 8, 'full-10Gigabps-none': 14, 'half-10Mbps-none': 4, 'half-1Gigabps-none': 12, 'full-10Mbps-none': 2, 'link-down': 0, 'half-10Gigabps-8023x': 15, 'full-1Gigabps-8023x': 9, 'empty': 17.
                 swL2PortInfoErrorDisabled 1.3.6.1.4.1.171.11.105.2.2.3.1.1.8 integer read-only
This object indicates the blocking type of this port. Enumeration: 'ctp-lbd': 4, 'none': 0, 'unknow': 3, 'storm': 1.
         swL2PortCtrlTable 1.3.6.1.4.1.171.11.105.2.2.3.2 no-access
A table that contains control information about every port.
             swL2PortCtrlEntry 1.3.6.1.4.1.171.11.105.2.2.3.2.1 no-access
A list of control information for each port on the device.
                 swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.105.2.2.3.2.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCtrlMediumType 1.3.6.1.4.1.171.11.105.2.2.3.2.1.2 integer read-only
Indicates the medium type of the port number. Enumeration: 'copper': 1, 'fiber': 2.
                 swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.105.2.2.3.2.1.3 integer read-only
Indicates the ID of the unit in the device
                 swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.4 integer read-write
This object decides if the port is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.5 integer read-write
Chose the port speed, duplex mode, and N-Way function mode. Enumeration: 'nway-disabled-10Mbps-Full': 4, 'nway-disabled-1Gigabps-Full-master': 9, 'nway-enabled': 2, 'nway-disabled-1Gigabps-Full': 8, 'nway-disabled-1Gigabps-Full-slave': 10, 'other': 1, 'nway-disabled-100Mbps-Full': 6, 'nway-disabled-1Gigabps-Half': 7, 'nway-disabled-10Mbps-Half': 3, 'nway-disabled-100Mbps-Half': 5.
                 swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.6 integer read-write
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlLearningState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.7 integer read-write
This object decides if the port is locked or not. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.8 integer read-write
This object sets each port's MAC notification state. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlMDIXState 1.3.6.1.4.1.171.11.105.2.2.3.2.1.10 integer read-write
This object configures the MDIX setting of the port. Enumeration: 'auto': 1, 'cross': 3, 'normal': 2.
         swL2PortCtrlJumboFrame 1.3.6.1.4.1.171.11.105.2.2.3.3 integer read-write
This object configures the switch's jumbo frame settings. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2PortCtrlJumboFrameMaxSize 1.3.6.1.4.1.171.11.105.2.2.3.4 integer read-only
This object describes how many bytes the max jumbo frame is.
         swL2PortCableDiagnosisTable 1.3.6.1.4.1.171.11.105.2.2.3.5 no-access
A table that contains cable diagnostic information about every port.
             swL2PortCableDiagnosisEntry 1.3.6.1.4.1.171.11.105.2.2.3.5.1 no-access
A list of cable diagnostic information for each port of the device.
                 swL2PortCableDiagnosisPortIndex 1.3.6.1.4.1.171.11.105.2.2.3.5.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCableDiagnosisPairIndex 1.3.6.1.4.1.171.11.105.2.2.3.5.1.2 integer read-only
Indicates pair index of the port. The pair 1 means the pin 3 and 6 of the connector. The pair 2 means the pin 1 and 2 of the connector. The pair 3 means the pin 7 and 8 of the connector. The pair 4 means the pin 4 and 5 of the connector.
                 swL2PortCableDiagnosisCableStatus 1.3.6.1.4.1.171.11.105.2.2.3.5.1.3 integer read-only
This object indicates the cable status. Enumeration: 'not-support': 4, 'short': 2, 'ok': 0, 'unknown': 5, 'open-short': 3, 'open': 1.
                 swL2PortCableDiagnosisPairStatus 1.3.6.1.4.1.171.11.105.2.2.3.5.1.4 integer read-only
This object indicates the status of the pair. Enumeration: 'short': 2, 'ok': 0, 'unknown': 5, 'not-supported': 4, 'fail': 3, 'open': 1.
                 swL2PortCableDiagnosisPairLength 1.3.6.1.4.1.171.11.105.2.2.3.5.1.5 integer read-only
This object indicates the approx. length or length to failure of the pair. The unit value is in meters.
                 swL2PortCableDiagnosisPairLengthInaccuracy 1.3.6.1.4.1.171.11.105.2.2.3.5.1.6 integer read-only
This object indicates the inaccuracy of a pair length. The unit value is in meters.
         swL2PortCounterCtrlTable 1.3.6.1.4.1.171.11.105.2.2.3.6 no-access
A table that used to clear counter information about every port.
             swL2PortCounterCtrlEntry 1.3.6.1.4.1.171.11.105.2.2.3.6.1 no-access
A list of entry used to clear counter information for each port of the device.
                 swL2PortCounterCtrlPortIndex 1.3.6.1.4.1.171.11.105.2.2.3.6.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCounterClearCtrl 1.3.6.1.4.1.171.11.105.2.2.3.6.1.2 integer read-write
This object indicates if to clear the counters for each port of the device or not. Enumeration: 'start': 2, 'other': 1.
         swL2PortErrTable 1.3.6.1.4.1.171.11.105.2.2.3.7 no-access
A table that contains error information for each port.
             swL2PortErrEntry 1.3.6.1.4.1.171.11.105.2.2.3.7.1 no-access
A list of information regarding port errors on the device.
                 swL2PortErrPortIndex 1.3.6.1.4.1.171.11.105.2.2.3.7.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module).
                 swL2PortErrPortState 1.3.6.1.4.1.171.11.105.2.2.3.7.1.2 integer read-only
This object indicates the port state is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.
                 swL2PortErrPortConnStatus 1.3.6.1.4.1.171.11.105.2.2.3.7.1.3 integer read-only
This object indicates whether the PortStatus is err-disabled or not. Enumeration: 'other': 1, 'err-disabled': 2.
                 swL2PortErrPortReason 1.3.6.1.4.1.171.11.105.2.2.3.7.1.4 integer read-only
This object describes if the reason for the port error is STP LBD or Storm control. Enumeration: 'ctp-lbd': 3, 'storm-control': 2.
     swL2LimitedMulticastMgmt 1.3.6.1.4.1.171.11.105.2.2.5
         swL2MulticastFilterProfileTable 1.3.6.1.4.1.171.11.105.2.2.5.1 no-access
A table that contains information about multicast filter address.
             swL2MulticastFilterProfileEntry 1.3.6.1.4.1.171.11.105.2.2.5.1.1 no-access
A list of multicast filter address information for each profile ID.
                 swL2MulticastFilterProfileIndex 1.3.6.1.4.1.171.11.105.2.2.5.1.1.1 integer read-only
Indicates index for each profile.
                 swL2MulticastFilterProfileName 1.3.6.1.4.1.171.11.105.2.2.5.1.1.2 displaystring read-only
Specifies a profile name for each multicast filter profile.
                 swL2MulticastFilterStatus 1.3.6.1.4.1.171.11.105.2.2.5.1.1.3 rowstatus read-only
This object indicates the status of this entry.
         swL2MulticastFilterProfileAddressTable 1.3.6.1.4.1.171.11.105.2.2.5.2 no-access
A table that contains information about multicast filter address.
             swL2MulticastFilterProfileAddressEntry 1.3.6.1.4.1.171.11.105.2.2.5.2.1 no-access
A list of multicast filter address information for each profile ID.
                 swL2MulticastFilterProfileIdIndex 1.3.6.1.4.1.171.11.105.2.2.5.2.1.1 integer read-only
Indicates index for each profile.
                 swL2MulticastFilterFromIp 1.3.6.1.4.1.171.11.105.2.2.5.2.1.2 ipaddress read-only
Specifies the head IP address of a multicast address range which will be binded to a multicast filter profile.
                 swL2MulticastFilterToIp 1.3.6.1.4.1.171.11.105.2.2.5.2.1.3 ipaddress read-only
Specifies the tail IP address of a multicast address range which will be binded to a multicast filter profile.
                 swL2MulticastFilterAddressState 1.3.6.1.4.1.171.11.105.2.2.5.2.1.4 rowstatus read-only
This object indicates the status of this entry. Setting value to createAndGo(4) will add the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp to multicast filter profile. Setting value to destroy(6) will remove the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp from multicast filter profile.
         swL2LimitedMulticastFilterPortTable 1.3.6.1.4.1.171.11.105.2.2.5.3 no-access
A table that used to bind port to profile id.
             swL2LimitedMulticastFilterPortEntry 1.3.6.1.4.1.171.11.105.2.2.5.3.1 no-access
A list of information that used to bind port to profile id.
                 swL2LimitedMulticastFilterPortIndex 1.3.6.1.4.1.171.11.105.2.2.5.3.1.1 integer read-only
Specifies port as an index.
                 swL2LimitedMulticastFilterPortAccess 1.3.6.1.4.1.171.11.105.2.2.5.3.1.2 integer read-write
This object indicates the access status for each port. Enumeration: 'deny': 2, 'permit': 1.
                 swL2LimitedMulticastFilterPortProfileID 1.3.6.1.4.1.171.11.105.2.2.5.3.1.3 displaystring read-write
This object specifies a profile ID list for each port.
                 swL2LimitedMulticastFilterPortProfileStatus 1.3.6.1.4.1.171.11.105.2.2.5.3.1.4 integer read-only
Controls the multicast filter profile list which bind to each port. When set add(2), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be bound to the port. When set delete(3), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be unbound from the port. The attribute value reverts to 'other' once the action has been done. Enumeration: 'add': 2, 'other': 1, 'delete': 3.
         swL2MulticastFilterPortMaxGroupTable 1.3.6.1.4.1.171.11.105.2.2.5.4 no-access
A table that contains information about max group number based on port.
             swL2MulticastFilterPortMaxGroupEntry 1.3.6.1.4.1.171.11.105.2.2.5.4.1 no-access
A list of max group number information for each port.
                 swL2MulticastFilterPortMaxGroupPortIndex 1.3.6.1.4.1.171.11.105.2.2.5.4.1.1 integer read-only
Specifies port number as table index.
                 swL2MulticastFilterPortMaxGroup 1.3.6.1.4.1.171.11.105.2.2.5.4.1.2 integer read-write
Specifies maximum multicast filter group numbers for each port. Default value is 0,and 0 means infinite.
     swL2QOSMgmt 1.3.6.1.4.1.171.11.105.2.2.6
         swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.105.2.2.6.1 no-access
.
             swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.105.2.2.6.1.1 no-access
A list of information contained in the swL2QOSBandwidthControlTable.
                 swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.105.2.2.6.1.1.1 integer read-only
Indicates the port .
                 swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.105.2.2.6.1.1.2 integer read-write
Indicates RX Rate of the specified port. Value 1024001 means no limit.
                 swL2QOSBandwidthTxRate 1.3.6.1.4.1.171.11.105.2.2.6.1.1.3 integer read-write
Indicates TX Rate of the specified port. Value 1024001 means no limit.
                 swL2QOSBandwidthRadiusRxRate 1.3.6.1.4.1.171.11.105.2.2.6.1.1.4 integer read-only
The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.
                 swL2QOSBandwidthRadiusTxRate 1.3.6.1.4.1.171.11.105.2.2.6.1.1.5 integer read-only
The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.
         swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.105.2.2.6.2 no-access
.
             swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.105.2.2.6.2.1 no-access
A list of information contained in the swL2QOSSchedulingTable.
                 swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.105.2.2.6.2.1.1 integer read-only
Indicates the hardware queue number.
                 swL2QOSSchedulingMaxPkts 1.3.6.1.4.1.171.11.105.2.2.6.2.1.2 integer read-write
Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.
                 swL2QOSSchedulingMechanism 1.3.6.1.4.1.171.11.105.2.2.6.2.1.3 integer read-only
Indicates the mechanism of QoS scheduling. Enumeration: 'weightfair': 3, 'strict': 1, 'roundrobin': 2.
                 swL2QOSSchedulingMaxLatency 1.3.6.1.4.1.171.11.105.2.2.6.2.1.4 integer read-write
Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmitting its packets. A value between 0 and 255 can be specified- with this value multiplied by 16 ms to arrive at the total allowed time for queue to transmit packets. For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting the last packet until it is finished when the max_latency timer expires.
         swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.105.2.2.6.3 no-access
.
             swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.105.2.2.6.3.1 no-access
A list of information contained in the swL2QOS8021pUserPriorityTable.
                 swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.105.2.2.6.3.1.1 integer read-only
The 802.1p user priority .
                 swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.105.2.2.6.3.1.2 integer read-write
The number of the switch's hardware priority queue. The switch has seven hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).
         swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.105.2.2.6.4 no-access
.
             swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.105.2.2.6.4.1 no-access
A list of information contained in the swL2QOS8021pDefaultPriorityTable.
                 swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.105.2.2.6.4.1.1 integer read-only
Indicates the port number .
                 swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.105.2.2.6.4.1.2 integer read-write
The priority value to assign to untagged packets received by the switch ports on the switch..
                 swL2QOS8021pRadiusPriority 1.3.6.1.4.1.171.11.105.2.2.6.4.1.3 integer read-only
The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
         swL2QOSSchedulingMechanismCtrl 1.3.6.1.4.1.171.11.105.2.2.6.5 integer read-write
This object controls QoS scheduling Mechanism. Enumeration: 'weightfair': 3, 'strict': 1, 'roundrobin': 2.
         swL2QOSHolPreventionCtrl 1.3.6.1.4.1.171.11.105.2.2.6.6 integer read-write
Controls QoS HoL Prevention Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2PortSecurityMgmt 1.3.6.1.4.1.171.11.105.2.2.7
         swL2PortSecurityControlTable 1.3.6.1.4.1.171.11.105.2.2.7.1 no-access
A port security feature which controls the address leaning capability and traffic forwarding decisions. Each port can be enabled or disabled for this function. When it is enabled and a number is given said N, which allows N addresses to be learned on this port, the first N learned addresses are locked at this port as static entries. When the learned addresses number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned on this port.
             swL2PortSecurityControlEntry 1.3.6.1.4.1.171.11.105.2.2.7.1.1 no-access
A list of information contained in the swL2PortSecurityControlTable.
                 swL2PortSecurityPortIndex 1.3.6.1.4.1.171.11.105.2.2.7.1.1.1 integer read-only
Indicates the secured port to lock address learning.
                 swL2PortSecurityMaxLernAddr 1.3.6.1.4.1.171.11.105.2.2.7.1.1.2 integer read-write
Indicates allowable number of addresses to be learned on this port.
                 swL2PortSecurityMode 1.3.6.1.4.1.171.11.105.2.2.7.1.1.3 integer read-write
Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset(4) mode - Locked addresses never age out unless the system restarts which will prevent port movement or intrusion. Enumeration: 'permanent': 2, 'other': 1, 'deleteOnTimeout': 3, 'deleteOnReset': 4.
                 swL2PortSecurityAdmState 1.3.6.1.4.1.171.11.105.2.2.7.1.1.4 integer read-write
Indicates administration state of locking address. Enumeration: 'enable': 2, 'other': 1, 'disable': 3.
                 swL2PortSecurityEntryClearCtrl 1.3.6.1.4.1.171.11.105.2.2.7.1.1.5 integer read-write
Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'. Enumeration: 'start': 2, 'other': 1.
         swL2PortSecurityDelCtrl 1.3.6.1.4.1.171.11.105.2.2.7.2
             swL2PortSecurityDelVlanName 1.3.6.1.4.1.171.11.105.2.2.7.2.1 displaystring read-write
Indicates VLAN name.
             swL2PortSecurityDelPort 1.3.6.1.4.1.171.11.105.2.2.7.2.2 integer read-write
Indicates the port.
             swL2PortSecurityDelMacAddress 1.3.6.1.4.1.171.11.105.2.2.7.2.3 macaddress read-write
Specifies a MAC address.
             swL2PortSecurityDelActivity 1.3.6.1.4.1.171.11.105.2.2.7.2.4 integer read-write
. Enumeration: 'start': 2, 'none': 1.
         swL2PortSecurityTrapLogState 1.3.6.1.4.1.171.11.105.2.2.7.3 integer read-write
When enabled(2),whenever there's a new MAC address that violates the pre-defined port security configuration, traps will be sent out and the relevant information will be logged into the system. Enumeration: 'enable': 2, 'other': 1, 'disable': 3.
     swL2DhcpRelayMgmt 1.3.6.1.4.1.171.11.105.2.2.8
         swL2DhcpRelayState 1.3.6.1.4.1.171.11.105.2.2.8.1 integer read-write
This object indicates if the DHCP relay function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2DhcpRelayHopCount 1.3.6.1.4.1.171.11.105.2.2.8.2 integer read-write
This object indicates the maximum number of router hops that DHCP packets can cross.
         swL2DhcpRelayTimeThreshold 1.3.6.1.4.1.171.11.105.2.2.8.3 integer read-write
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
         swL2DhcpRelayOption82State 1.3.6.1.4.1.171.11.105.2.2.8.4 integer read-write
This object indicates if the DHCP relay agent information option 82 function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2DhcpRelayOption82Check 1.3.6.1.4.1.171.11.105.2.2.8.5 integer read-write
This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2DhcpRelayOption82Policy 1.3.6.1.4.1.171.11.105.2.2.8.6 integer read-write
This object indicates the reforwarding policy of DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option 82 field messages. Enumeration: 'keep': 3, 'drop': 2, 'replace': 1.
         swL2DhcpRelayCtrlTable 1.3.6.1.4.1.171.11.105.2.2.8.7 no-access
This table specifies the IP address as a destination to forward (relay) DHCP packets to.
             swL2DhcpRelayCtrlEntry 1.3.6.1.4.1.171.11.105.2.2.8.7.1 no-access
A list of information that specifies the IP address as a destination to forward (relay) DHCP packets to.
                 swL2DhcpRelayCtrlInterfaceName 1.3.6.1.4.1.171.11.105.2.2.8.7.1.1 displaystring read-only
The name of the IP interface.
                 swL2DhcpRelayCtrlServer 1.3.6.1.4.1.171.11.105.2.2.8.7.1.2 ipaddress read-only
The DHCP server IP address.
                 swL2DhcpRelayCtrlState 1.3.6.1.4.1.171.11.105.2.2.8.7.1.3 integer read-write
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. Enumeration: 'other': 1, 'valid': 3, 'invalid': 2.
     swL2TrunkMgmt 1.3.6.1.4.1.171.11.105.2.2.9
         swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.105.2.2.9.1 integer read-only
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
         swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.105.2.2.9.2 integer read-only
Current active number of entries in the trunk configuration table.
         swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.105.2.2.9.3 no-access
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.105.2.2.9.3.1 no-access
A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkIndex 1.3.6.1.4.1.171.11.105.2.2.9.3.1.1 integer read-only
The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
                 swL2TrunkMasterPort 1.3.6.1.4.1.171.11.105.2.2.9.3.1.3 integer read-only
The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
                 swL2TrunkMember 1.3.6.1.4.1.171.11.105.2.2.9.3.1.4 portlist read-only
Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
                 swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.105.2.2.9.3.1.5 integer read-only
The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
                 swL2TrunkType 1.3.6.1.4.1.171.11.105.2.2.9.3.1.6 integer read-only
This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group . Enumeration: 'lacp': 3, 'other': 1, 'static': 2.
                 swL2TrunkState 1.3.6.1.4.1.171.11.105.2.2.9.3.1.7 rowstatus read-only
This object indicates the status of this entry.
         swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.105.2.2.9.4 integer read-write
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. Enumeration: 'ip-source': 5, 'mac-destination': 3, 'mac-source': 2, 'mac-source-dest': 4, 'ip-source-dest': 7, 'ip-destination': 6, 'other': 1.
         swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.105.2.2.9.5 no-access
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.105.2.2.9.5.1 no-access
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.105.2.2.9.5.1.1 integer read-only
The index of logical port LACP.
                 swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.105.2.2.9.5.1.2 integer read-write
The state of logical port LACP. Enumeration: 'active': 1, 'passive': 2.
         swL2TrunkVLANTable 1.3.6.1.4.1.171.11.105.2.2.9.6 no-access
This table is used to manage the VLAN trunking feature of the device.
             swL2TrunkVLANEntry 1.3.6.1.4.1.171.11.105.2.2.9.6.1 no-access
This object is used to configure the VLAN trunking settings for each port.
                 swL2TrunkVLANPort 1.3.6.1.4.1.171.11.105.2.2.9.6.1.1 integer read-only
This object indicates the port being configured.
                 swL2TrunkVLANState 1.3.6.1.4.1.171.11.105.2.2.9.6.1.2 integer read-write
The state of the logical port. Enumeration: 'disabled': 2, 'enabled': 1.
     swL2MirrorMgmt 1.3.6.1.4.1.171.11.105.2.2.10
           swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.105.2.2.10.1 integer read-write
This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
           swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.105.2.2.10.2 portlist read-write
This represents the port where ingress packets will be sniffed.
           swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.105.2.2.10.3 portlist read-write
This represents the port where egress packets will be sniffed.
           swL2MirrorPortState 1.3.6.1.4.1.171.11.105.2.2.10.4 integer read-write
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2IGMPMgmt 1.3.6.1.4.1.171.11.105.2.2.11
           swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.171.11.105.2.2.11.1 integer read-only
Maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
           swL2IGMPMaxIpGroupNumPerVlan 1.3.6.1.4.1.171.11.105.2.2.11.2 integer read-only
Maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table(swL2IGMPQueryInfoTable).
           swL2IGMPSnoopingMulticastVlanState 1.3.6.1.4.1.171.11.105.2.2.11.3 integer read-write
It indicates the global state of igmp_snoop multicast_vlan. Enumeration: 'disabled': 2, 'enabled': 1.
           swL2IGMPCtrlTable 1.3.6.1.4.1.171.11.105.2.2.11.4 no-access
The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN is disabled, there is only one entry in the table, with an index of 1. If the VLAN is in Port-Base or 802.1q mode, the maximum number of entries can be 12, with an index range from 1 to 12.
               swL2IGMPCtrlEntry 1.3.6.1.4.1.171.11.105.2.2.11.4.1 no-access
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
                   swL2IGMPCtrlVid 1.3.6.1.4.1.171.11.105.2.2.11.4.1.1 integer read-only
This object indicates the IGMP control entry's VLAN ID. If the VLAN is disabled, the VID is always 0 and cannot be changed by management users. If the VLAN is in Port-Base mode, the VID is arranged from 1 to 12, in a fixed form. If the VLAN is in 802.1q mode, the VID setting can be changed from 1 to 4094 by the management user, and the VID in each entry must be unique within the IGMP Control Table.
                   swL2IGMPQueryInterval 1.3.6.1.4.1.171.11.105.2.2.11.4.1.2 integer read-write
The frequency at which IGMP Host-Query packets are transmitted on this switch.
                   swL2IGMPMaxResponseTime 1.3.6.1.4.1.171.11.105.2.2.11.4.1.3 integer read-write
The maximum query response time on this switch.
                   swL2IGMPRobustness 1.3.6.1.4.1.171.11.105.2.2.11.4.1.4 integer read-write
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
                   swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.171.11.105.2.2.11.4.1.5 integer read-write
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
                   swL2IGMPHostTimeout 1.3.6.1.4.1.171.11.105.2.2.11.4.1.6 integer read-write
The timer value for sending IGMP query packets when none were sent by the host on the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query messages if the timer expires. Please reference RFC2236-1997.
                   swL2IGMPRouteTimeout 1.3.6.1.4.1.171.11.105.2.2.11.4.1.7 integer read-write
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
                   swL2IGMPLeaveTimer 1.3.6.1.4.1.171.11.105.2.2.11.4.1.8 integer read-write
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
                   swL2IGMPQueryState 1.3.6.1.4.1.171.11.105.2.2.11.4.1.9 integer read-write
This object decides if the IGMP query is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2IGMPCurrentState 1.3.6.1.4.1.171.11.105.2.2.11.4.1.10 integer read-only
This object indicates the current IGMP query state. Enumeration: 'non-querier': 3, 'other': 1, 'querier': 2.
                   swL2IGMPCtrlState 1.3.6.1.4.1.171.11.105.2.2.11.4.1.11 integer read-write
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP function is disabled for this entry. enable(3) - IGMP function is enabled for this entry. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.
                   swL2IGMPFastLeaveState 1.3.6.1.4.1.171.11.105.2.2.11.4.1.12 integer read-write
This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP fast-leave function is disabled for this entry. enable(3) - IGMP fast-leave function is enabled for this entry. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.
           swL2IGMPQueryInfoTable 1.3.6.1.4.1.171.11.105.2.2.11.5 no-access
The table contains the number current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
               swL2IGMPQueryInfoEntry 1.3.6.1.4.1.171.11.105.2.2.11.5.1 no-access
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of the associated VLAN entry are all enabled.
                   swL2IGMPInfoVid 1.3.6.1.4.1.171.11.105.2.2.11.5.1.1 integer read-only
This object indicates the VID of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
                   swL2IGMPInfoQueryCount 1.3.6.1.4.1.171.11.105.2.2.11.5.1.2 integer read-only
This object indicates the number of query packets received since the IGMP function was enabled, on a per-VLAN basis.
                   swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.171.11.105.2.2.11.5.1.3 integer read-only
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
           swL2IGMPInfoTable 1.3.6.1.4.1.171.11.105.2.2.11.6 no-access
The table containing current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of the associated VLAN entries are all enabled. Note that the priority of IGMP table entries is lower than the Filtering Table, i.e. if there is a table hash collision between entries in the IGMP Table and Filtering Table inside the switch's H/W address table, then Filtering Table entry overwrites the colliding entry of the IGMP Table. Also see the swL2FilterMgmt description.
               swL2IGMPInfoEntry 1.3.6.1.4.1.171.11.105.2.2.11.6.1 no-access
Information about current IGMP information which was captured by this device, provided that the swL2DevCtrlIGMPSnooping and the swL2IGMPCtrlState of associated VLAN entries are all enabled.
                   swL2IGMPVid 1.3.6.1.4.1.171.11.105.2.2.11.6.1.1 integer read-only
This object indicates the VID of individual IGMP table entries. It shows the VID IGMP report information captured on the network.
                   swL2IGMPGroupIpAddr 1.3.6.1.4.1.171.11.105.2.2.11.6.1.2 ipaddress read-only
This object identifies group IP addresses which were captured from IGMP packets, on a per-VLAN basis.
                   swL2IGMPMacAddr 1.3.6.1.4.1.171.11.105.2.2.11.6.1.3 macaddress read-only
This object identifies MAC addresses which correspond to the swL2IGMPGroupIpAddr, on per-VLAN basis.
                   swL2IGMPPortMap 1.3.6.1.4.1.171.11.105.2.2.11.6.1.4 portlist read-only
This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string which is indicated by a port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bits corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logical port. If the unit is less than 32 ports, other ports are not affected and are replaced with zeroes.
                   swL2IGMPIpGroupReportCount 1.3.6.1.4.1.171.11.105.2.2.11.6.1.5 integer read-only
This object indicates how many report packets were receive by our device, that correspond with this entry when the IGMP function is enabled on per-VLAN basis.
           swL2IGMPRouterPortTable 1.3.6.1.4.1.171.11.105.2.2.11.7 no-access
The information of the router port table.
               swL2IGMPRouterPortEntry 1.3.6.1.4.1.171.11.105.2.2.11.7.1 no-access
The entry of swL2IGMPRouterPortTable.
                   swL2IGMPRouterPortVlanid 1.3.6.1.4.1.171.11.105.2.2.11.7.1.1 integer read-only
This object indicates the VLAN ID of the router port entry.
                   swL2IGMPRouterPortVlanName 1.3.6.1.4.1.171.11.105.2.2.11.7.1.2 displaystring read-only
This object indicates the VLAN name of the router port entry.
                   swL2IGMPRouterPortStaticPortList 1.3.6.1.4.1.171.11.105.2.2.11.7.1.3 portlist read-write
This object indicates the static portlist of the router port entry.
                   swL2IGMPRouterPortDynamicPortList 1.3.6.1.4.1.171.11.105.2.2.11.7.1.4 portlist read-only
This object indicates the dynamic portlist of the router port entry.
                   swL2IGMPRouterPortForbiddenPortList 1.3.6.1.4.1.171.11.105.2.2.11.7.1.5 portlist read-write
This object indicates the forbidden portlist of the router port entry.
           swL2IGMPMulticastVlanTable 1.3.6.1.4.1.171.11.105.2.2.11.8 no-access
The information of the IGMP snooping multicast VLAN table.
               swL2IGMPMulticastVlanEntry 1.3.6.1.4.1.171.11.105.2.2.11.8.1 no-access
The entry of swL2IGMPMulticastVlanTable.
                   swL2IGMPMulticastVlanid 1.3.6.1.4.1.171.11.105.2.2.11.8.1.1 integer read-only
This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
                   swL2IGMPMulticastVlanName 1.3.6.1.4.1.171.11.105.2.2.11.8.1.2 displaystring read-only
This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
                   swL2IGMPMulticastVlanSourcePort 1.3.6.1.4.1.171.11.105.2.2.11.8.1.3 portlist read-write
This object indicate the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
                   swL2IGMPMulticastVlanMemberPort 1.3.6.1.4.1.171.11.105.2.2.11.8.1.4 portlist read-write
This object indicate the portlist of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry. And the IGMP control messages received from the member ports would be forwarded to the source ports.
                   swL2IGMPMulticastVlanTagMemberPort 1.3.6.1.4.1.171.11.105.2.2.11.8.1.5 portlist read-write
This object indicate the portlist of the tag member ports of IGMP snooping multicast VLAN.
                   swL2IGMPMulticastVlanState 1.3.6.1.4.1.171.11.105.2.2.11.8.1.6 integer read-write
This object can be enabled or disabled IGMP_snooping multicast VLAN. Enumeration: 'disabled': 2, 'enabled': 1.
                   swL2IGMPMulticastVlanReplaceSourceIp 1.3.6.1.4.1.171.11.105.2.2.11.8.1.7 ipaddress read-write
The replace source IP of this multicast vlan.
                   swL2IGMPMulticastVlanRowStatus 1.3.6.1.4.1.171.11.105.2.2.11.8.1.8 rowstatus read-only
This object indicates the status of this entry.
                   swL2IGMPMulticastVlanRemoveAllMcastAddrListAction 1.3.6.1.4.1.171.11.105.2.2.11.8.1.9 integer read-write
This object indicates if remove all the multicast address list from the IGMP multicast VLAN or not. Enumeration: 'start': 2, 'other': 1.
           swL2IGMPMulticastVlanGroupTable 1.3.6.1.4.1.171.11.105.2.2.11.9 no-access
The table containing the IGMP snooping multicast VLAN group information
               swL2IGMPMulticastVlanGroupEntry 1.3.6.1.4.1.171.11.105.2.2.11.9.1 no-access
Information about current IGMP snooping multicast VLAN group.
                   swL2IGMPMulticastVlanGroupVid 1.3.6.1.4.1.171.11.105.2.2.11.9.1.1 integer read-only
This object indicates the Vid of IGMP snooping multicast VLAN group.
                   swL2IGMPMulticastVlanGroupFromIp 1.3.6.1.4.1.171.11.105.2.2.11.9.1.2 ipaddress read-only
Specifies the multicast address list for this VLAN.
                   swL2IGMPMulticastVlanGroupToIp 1.3.6.1.4.1.171.11.105.2.2.11.9.1.3 ipaddress read-only
Specifies the multicast address list for this VLAN.
                   swL2IGMPMulticastVlanGroupStatus 1.3.6.1.4.1.171.11.105.2.2.11.9.1.4 rowstatus read-only
This object indicates the status of this entry.
     swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.105.2.2.14
           swL2TrafficSegTable 1.3.6.1.4.1.171.11.105.2.2.14.1 no-access
This table specifies that the port can just forward traffic to the specific port list.
               swL2TrafficSegEntry 1.3.6.1.4.1.171.11.105.2.2.14.1.1 no-access
A list of information which specifies the port with its traffic forwarding list.
                   swL2TrafficSegPort 1.3.6.1.4.1.171.11.105.2.2.14.1.1.1 integer read-only
The port number of the logical port.
                   swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.105.2.2.14.1.1.2 portlist read-write
The port list to which the specific port can forward traffic.
     swL2MulticastFilterMode 1.3.6.1.4.1.171.11.105.2.2.17
           swL2MulticastFilterModeVlanTable 1.3.6.1.4.1.171.11.105.2.2.17.1 no-access
A table that contains information about VLAN multicast filter mode.
               swL2MulticastFilterModeVlanEntry 1.3.6.1.4.1.171.11.105.2.2.17.1.1 no-access
A list of multicast filter mode information for each VLAN.
                   swL2MulticastFilterVid 1.3.6.1.4.1.171.11.105.2.2.17.1.1.1 integer read-only
Indicates VID for each VLAN.
                   swL2MulticastFilterVlanMode 1.3.6.1.4.1.171.11.105.2.2.17.1.1.2 integer read-write
Specifies multicast filter mode for each VLAN. Enumeration: 'forward-unregistered-groups': 2, 'forward-all-groups': 1, 'filter-unregistered-groups': 3.
     swL2LoopDetectMgmt 1.3.6.1.4.1.171.11.105.2.2.18
           swL2LoopDetectCtrl 1.3.6.1.4.1.171.11.105.2.2.18.1
               swL2LoopDetectAdminState 1.3.6.1.4.1.171.11.105.2.2.18.1.1 integer read-write
This object indicates the loopback detection status for the system. Enumeration: 'disabled': 2, 'enabled': 1.
               swL2LoopDetectInterval 1.3.6.1.4.1.171.11.105.2.2.18.1.2 integer read-write
This object indicates the interval value, the range is from 1 to 32767 seconds.
               swL2LoopDetectRecoverTime 1.3.6.1.4.1.171.11.105.2.2.18.1.3 integer read-write
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
               swL2LoopDetectMode 1.3.6.1.4.1.171.11.105.2.2.18.1.4 integer read-write
This object indicates the loopback detection mode for the system. Enumeration: 'port-based': 2, 'vlan-based': 1.
               swL2LoopDetectTrapMode 1.3.6.1.4.1.171.11.105.2.2.18.1.5 integer read-write
This object indicates the loopback detection trap mode for the system. Enumeration: 'both': 4, 'none': 1, 'loop_cleared': 3, 'loop_detected': 2.
           swL2LoopDetectPortMgmt 1.3.6.1.4.1.171.11.105.2.2.18.2
               swL2LoopDetectPortTable 1.3.6.1.4.1.171.11.105.2.2.18.2.1 no-access
The table specifies the loopback detection function specified by port.
                   swL2LoopDetectPortEntry 1.3.6.1.4.1.171.11.105.2.2.18.2.1.1 no-access
The table specifies the loopback detection function specified by port.
                       swL2LoopDetectPortIndex 1.3.6.1.4.1.171.11.105.2.2.18.2.1.1.1 integer read-only
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
                       swL2LoopDetectPortState 1.3.6.1.4.1.171.11.105.2.2.18.2.1.1.2 integer read-write
This object indicates the loopback detection function state on the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       swL2LoopDetectPortLoopVLAN 1.3.6.1.4.1.171.11.105.2.2.18.2.1.1.3 displaystring read-only
This object indicates the VLAN list that has detected a loopback.
                       swL2LoopDetectPortLoopStatus 1.3.6.1.4.1.171.11.105.2.2.18.2.1.1.4 integer read-only
This object indicates the port status. Enumeration: 'none': 4, 'error': 3, 'loop': 2, 'normal': 1.
     swL2DhcpLocalRelayMgmt 1.3.6.1.4.1.171.11.105.2.2.24
           swL2DhcpLocalRelayState 1.3.6.1.4.1.171.11.105.2.2.24.1 integer read-write
This object indicates the status of the DHCP local relay function of the switch. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
           swL2DhcpLocalRelayVLANTable 1.3.6.1.4.1.171.11.105.2.2.24.2 no-access
This table is used to manage the DHCP local relay status for each VLAN.
               swL2DhcpLocalRelayVLANEntry 1.3.6.1.4.1.171.11.105.2.2.24.2.1 no-access
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
                   swL2DhcpLocalRelayVLANID 1.3.6.1.4.1.171.11.105.2.2.24.2.1.1 integer read-only
This object shows the VIDs of the current VLANS in the switch.
                   swL2DhcpLocalRelayVLANState 1.3.6.1.4.1.171.11.105.2.2.24.2.1.2 integer read-write
This object indicates the status of the DHCP relay function of the VLAN. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2PPPoEMgmt 1.3.6.1.4.1.171.11.105.2.2.25
           swL2PPPoECirIDinsertState 1.3.6.1.4.1.171.11.105.2.2.25.1 integer read-write
This object indicates the status of the PPPoE circuit ID insertion state of the switch. Enumeration: 'disabled': 2, 'enabled': 1.
     swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.105.2.2.100
             swL2Notify 1.3.6.1.4.1.171.11.105.2.2.100.1
                 swL2NotifyMgmt 1.3.6.1.4.1.171.11.105.2.2.100.1.1
                     swL2macNotificationSeverity 1.3.6.1.4.1.171.11.105.2.2.100.1.1.1 agentnotifylevel read-write
Indicate the level of macNotification detection.
                     swL2PortSecurityViolationSeverity 1.3.6.1.4.1.171.11.105.2.2.100.1.1.2 agentnotifylevel read-write
Indicate the level of PortSecurityViolation detection.
                 swL2NotifyPrefix 1.3.6.1.4.1.171.11.105.2.2.100.1.2
                     swL2NotifFirmware 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0
                         swL2macNotification 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.1
This trap indicates the MAC addresses variation in address table .
                         swL2PortSecurityViolationTrap 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.2
When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.
                         swL2PortLoopOccurred 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.3
The trap is sent when Port loop occurred.
                         swL2PortLoopRestart 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.4
The trap is sent when Port loop restart after interval time.
                         swL2VlanLoopOccurred 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.5
The trap is sent when Port with VID loop occurred.
                         swL2VlanLoopRestart 1.3.6.1.4.1.171.11.105.2.2.100.1.2.0.6
The trap is sent when Port with VID loop restart after interval time.
                     swl2NotificationBidings 1.3.6.1.4.1.171.11.105.2.2.100.1.2.1
                         swL2macNotifyInfo 1.3.6.1.4.1.171.11.105.2.2.100.1.2.1.1 octet string read-only
This object indicates the last time reboot information.
                         swL2PortSecurityViolationMac 1.3.6.1.4.1.171.11.105.2.2.100.1.2.1.2 macaddress no-access
This object indicates the MAC address that violates the port security configuration.
                         swL2VlanLoopDetectVID 1.3.6.1.4.1.171.11.105.2.2.100.1.2.1.3 integer no-access
This object indicates the VID that has detected a loopback.