CISCO-CNO-SWITCH-MIB: View SNMP OID List / Download MIB

VENDOR: CISCO


 Home MIB: CISCO-CNO-SWITCH-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, CISCO-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 ciscoCNOSwitchMIB 1.3.6.1.4.1.9.10.43
The MIB module for the management of Cisco Network Office (CNO) switch products.
       ciscoCNOSwitchMIBObjects 1.3.6.1.4.1.9.10.43.1
           cnosSysInfo 1.3.6.1.4.1.9.10.43.1.1
               cnosSysInfoSerialNo 1.3.6.1.4.1.9.10.43.1.1.1 displaystring read-only
Serial number of the hardware.
               cnosSysInfoBoardRevision 1.3.6.1.4.1.9.10.43.1.1.2 integer32 read-only
Returns the revision number of the switch main board on which the system firmware resides.
               cnosSysInfoBootVersion 1.3.6.1.4.1.9.10.43.1.1.3 displaystring read-only
Returns the version number of the switch boot S/W residing in flash. The format is 'V1.2.3'.
               cnosSysInfoAddrCapacity 1.3.6.1.4.1.9.10.43.1.1.4 integer32 read-only
The system-wide maximum number of addresses supported.
           cnosSysConfig 1.3.6.1.4.1.9.10.43.1.2
               cnosSysConfigReset 1.3.6.1.4.1.9.10.43.1.2.1 integer read-write
Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read. Enumeration: 'reset': 2, 'noReset': 1.
               cnosSysConfigDefaultReset 1.3.6.1.4.1.9.10.43.1.2.2 integer read-write
Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parameters will revert to their factory default settings, and all addresses assigned will be removed. Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read. Enumeration: 'reset': 2, 'noReset': 1.
               cnosSysConfigMonitor 1.3.6.1.4.1.9.10.43.1.2.3 integer read-write
Selects whether frames to/from certain ports are sent to conSwitchSysConfigMonitorPort. A port is selected for monitoring purpose when its cnosPortMonitoring object is set to enabled. Enumeration: 'disabled': 2, 'enabled': 1.
               cnosSysConfigMonitorPort 1.3.6.1.4.1.9.10.43.1.2.4 integer32 read-write
Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is set to enabled(1). A number from 1 to 8 selects a switch port. The number 0 selects no monitor port.
           cnosPort 1.3.6.1.4.1.9.10.43.1.3
               cnosPortTable 1.3.6.1.4.1.9.10.43.1.3.1 no-access
A list of configuration entries for individually switched ports. There in one entry created automatically for each switch port (ifType of ethernetCsmacd) on the device.
                   cnosPortEntry 1.3.6.1.4.1.9.10.43.1.3.1.1 no-access
Configuration parameters for an individually switched port.
                       cnosPortControllerRevision 1.3.6.1.4.1.9.10.43.1.3.1.1.1 integer32 read-only
Returns the revision number of the port controller.
                       cnosPortName 1.3.6.1.4.1.9.10.43.1.3.1.1.2 displaystring read-write
A descriptive string of up to 80 characters used by the network administrator to name a port.
                       cnosPortDuplexAdmin 1.3.6.1.4.1.9.10.43.1.3.1.1.3 integer read-write
Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to operate in normal mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. Enumeration: 'autoNegotiate': 3, 'fullDuplex': 1, 'halfDuplex': 2.
                       cnosPortDuplexStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.4 integer read-only
The operating duplex mode of the switched port. Enumeration: 'fullDuplex': 1, 'halfDuplex': 2.
                       cnosPortSpeedAdmin 1.3.6.1.4.1.9.10.43.1.3.1.1.5 integer read-write
Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection. Enumeration: 'tenMbps': 1, 'oneHundredMbps': 2, 'autoNegotiate': 3.
                       cnosPortSpeedStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.6 integer read-only
The operating speed of the switched port. Enumeration: 'tenMbps': 1, 'oneHundredMbps': 2.
                       cnosPortMonitoring 1.3.6.1.4.1.9.10.43.1.3.1.1.7 integer read-write
Set to enabled(1) to forward receive and transmit frames on this port to the port identified by cnosSysConfigMonitorPort. Set to disabled(2) to not monitor frame traffic on this port. Enumeration: 'disabled': 2, 'enabled': 1.
                       cnosPortLinkStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.8 integer read-only
The current port link status. Enumeration: 'link': 1, 'noLink': 2.
                       cnosPortSTPPortFastMode 1.3.6.1.4.1.9.10.43.1.3.1.1.9 integer read-write
This object configures the port into the Spanning Tree port-fast mode. When enabled(1), the STP can transition the port's state directly from blocking to forwarding, and vice versa, without going through the intermediate listening and learning states. This object should only be enabled for a port that is connected to a single workstation. A port that is attached to a network segment with multiple network nodes or bridges should have this object set to disabled(2) since a temporary loop may occur when port changes state. Enumeration: 'disabled': 2, 'enabled': 1.
                       cnosPortVlanMember 1.3.6.1.4.1.9.10.43.1.3.1.1.10 integer read-write
Set the port to be a member of a specified VLAN. Set the port to all(5) to be shared among all VLANs. Enumeration: 'vlan1': 1, 'vlan2': 2, 'vlan3': 3, 'vlan4': 4, 'all': 5.
           cnosVlan 1.3.6.1.4.1.9.10.43.1.4
               cnosVlanTable 1.3.6.1.4.1.9.10.43.1.4.1 no-access
Table containing a list of VLANs.
                   cnosVlanEntry 1.3.6.1.4.1.9.10.43.1.4.1.1 no-access
Information pertaining to a VLAN.
                       cnosVlanIndex 1.3.6.1.4.1.9.10.43.1.4.1.1.1 integer32 no-access
Identification of a VLAN entry.
                       cnosVlanSTPState 1.3.6.1.4.1.9.10.43.1.4.1.1.2 integer read-write
The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology. The user may, for any reason, elect to disable the execution of STP, by setting this object to disabled(2). Enumeration: 'disabled': 2, 'enabled': 1.
       ciscoCNOSwitchNotifications 1.3.6.1.4.1.9.10.43.2
           ciscoCNOSwitchNotificationsPrefix 1.3.6.1.4.1.9.10.43.2.0
       ciscoCNOSwitchMIBComformance 1.3.6.1.4.1.9.10.43.3
           ciscoCNOSwitchMIBCompliances 1.3.6.1.4.1.9.10.43.3.1
               ciscoCNOSwitchCompliance 1.3.6.1.4.1.9.10.43.3.1.1
The compliance statement for the Cisco CNO switch products.
           ciscoCNOSwitchMIBGroups 1.3.6.1.4.1.9.10.43.3.2
               ciscoCNOSwitchSysInfoGroup 1.3.6.1.4.1.9.10.43.3.2.1
A collection of the system information objects for use with the Cisco CNO switch products.
               ciscoCNOSwitchConfigGroup 1.3.6.1.4.1.9.10.43.3.2.2
A collection of the system configuration objects for use with the Cisco CNO switch products.
               ciscoCNOSwitchPortGroup 1.3.6.1.4.1.9.10.43.3.2.3
A collection of the the switched port objects for use with the Cisco CNO switch products.
               ciscoCNOSwitchMonitorPortGroup 1.3.6.1.4.1.9.10.43.3.2.4
A collection of the switched port monitoring objects for use with the Cisco CNO switch products.
               ciscoCNOSwitchVlanGroup 1.3.6.1.4.1.9.10.43.3.2.5
A collection of the VLAN objects for use with the Cisco CNO switch products.