BREEZECOM-MIB: View SNMP OID List / Download MIB

VENDOR: LANNAIR LTD.


 Home MIB: BREEZECOM-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 breezecom 1.3.6.1.4.1.710
         breezecomPrvRev 1.3.6.1.4.1.710.3
             brznetmib 1.3.6.1.4.1.710.3.2
                 brzSys 1.3.6.1.4.1.710.3.2.1
                     sysCmd 1.3.6.1.4.1.710.3.2.1.1
                         sysReset 1.3.6.1.4.1.710.3.2.1.1.1 integer read-write
Setting the value of this attribute to ON is interpreted as a reset command for the system. Enumeration: 'on': 1, 'off': 2.
                         sysSetDefaults 1.3.6.1.4.1.710.3.2.1.1.2 integer read-write
Setting the value of this attribute to ON will cause the system to set the NVRAM parameters to the factory default values. These values will become active after the next system reset Enumeration: 'on': 1, 'off': 2.
                         sysResetCounters 1.3.6.1.4.1.710.3.2.1.1.3 integer read-write
Setting the value of this attribute to ON will cause the system to clear the performance counters. Enumeration: 'on': 1, 'off': 2.
                         sysTrapEnable 1.3.6.1.4.1.710.3.2.1.1.4 integer read-write
Setting the value of this attribute to OFF will disable the system from sending TRAPs. Enumeration: 'on': 1, 'off': 2.
                         sysTrapCounter 1.3.6.1.4.1.710.3.2.1.1.5 counter read-only
This attribute counts the total number of traps generated by the device, since initialization.
                         sysCarrierSense 1.3.6.1.4.1.710.3.2.1.1.6 integer read-write
This attribute defines the carrier sense absolute threshold
                         sysDeltaCarrierSense 1.3.6.1.4.1.710.3.2.1.1.7 integer read-write
This attribute defines the carrier sense differential threshold
                         sysPartialDefaults 1.3.6.1.4.1.710.3.2.1.1.8 integer read-write
Setting the value of this attribute to ON will cause the system to set the partial NVRAM parameters to the factory default values. These values will become active after the next system reset Enumeration: 'on': 1, 'off': 2.
                         sysRunFromNonActiveCode 1.3.6.1.4.1.710.3.2.1.1.9 integer read-write
This attribute make you run from non active code. Automatic switch is done if the non active code is valid. To activate set to On. If the switch succeed no response will be sent to the SNMP browser. Enumeration: 'on': 1, 'off': 0.
                         accessRights 1.3.6.1.4.1.710.3.2.1.1.10
                               sysDisplayAccessRights 1.3.6.1.4.1.710.3.2.1.1.10.1 integer read-only
This attribute Display the access rights of that station. Enumeration: 'installer': 1, 'user': 0, 'authorized-technician': 2.
                               sysChangeRightsToUSER 1.3.6.1.4.1.710.3.2.1.1.10.2 integer read-write
This attribute let you change the access rights of that station to USER. Enumeration: 'unchanged': 0, 'change': 1.
                               sysChangeRightsToINSTALLER 1.3.6.1.4.1.710.3.2.1.1.10.3 displaystring read-write
This attribute let you change the access rights of that station to INSTALLER. Type the Installer password for the desired access right.
                               sysChangeRightsToTECHNICIAN 1.3.6.1.4.1.710.3.2.1.1.10.4 displaystring read-write
This attribute let you change the access rights of that station to AUTHORIZED TECHNICIAN. Type the Technician password for the desired access right.
                               sysChangeInstallerPassword 1.3.6.1.4.1.710.3.2.1.1.10.5 displaystring read-write
This attribute let you change the Installer Password of that station. Type the new password, maximum 8 characters.
                         sysNoiseFloor 1.3.6.1.4.1.710.3.2.1.1.11 integer read-write
This attribute defines the low RSSI threshold in DBM units. Allowed range is from -120 to -50 dbm.
                         sysExternalAmplifier 1.3.6.1.4.1.710.3.2.1.1.12 integer read-write
This attribute is set to 1 when external amplifier is connected to the device and set to 0 when device is connected to anntena. Enumeration: 'on': 1, 'off': 0.
                     sysParams 1.3.6.1.4.1.710.3.2.1.2
                         brzHWMacAddress 1.3.6.1.4.1.710.3.2.1.2.1 macaddress read-only
The Hardware MAC address of the device.
                         brzApplTunneling 1.3.6.1.4.1.710.3.2.1.2.2 integer read-write
This attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-talk - The device will enable AppleTalk tunneling only. none - The device will disable tunneling. both - The device will enable only IPX and AppleTalk tunneling. Enumeration: 'both': 1, 'ipx': 0, 'none': 2, 'apple-talk': 3.
                         brzPositiveBrg 1.3.6.1.4.1.710.3.2.1.2.3 integer read-write
This attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the Wireless LAN only frames that are destined to associated stations. forward-unknown - The AP forwards to the Wireless LAN frames destined to associated AND unknown addresses. This value should be used only for Wireless Bridge installations. intelligent - If connected to a wireless bridge, the AP automatically activates the Forward-Unknown option. na - A not applicable value, for non-AP devices. Enumeration: 'forward-unknown': 2, 'intelligent': 3, 'reject-unknown': 1, 'na': 255.
                         brzIpFilter 1.3.6.1.4.1.710.3.2.1.2.4 integer read-write
Setting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be used on environments where only IP (and ARP) traffic is permitted. Enumeration: 'on': 1, 'off': 2, 'na': 255.
                         brzTranslationMode 1.3.6.1.4.1.710.3.2.1.2.5 integer read-write
When this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunneling of data frames apply. All devices within the same Wireless LAN network, must have the same Translation Mode assigned. Enumeration: 'on': 1, 'off': 2.
                         brzWIXSupport 1.3.6.1.4.1.710.3.2.1.2.6 integer read-write
This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network. Enumeration: 'on': 1, 'off': 2.
                         brzWlanNetID 1.3.6.1.4.1.710.3.2.1.2.7 displaystring read-write
This attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.
                         brzAuthenticationType 1.3.6.1.4.1.710.3.2.1.2.8 integer read-only
This attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one of the following: 1 - Open System, 2 - Shared Key, 20 - Special Authentication Algorithm (#0), 21 - Special Authentication Algorithm (#1), 22 - Special Authentication Algorithm (#2).
                         brzWlanRTNetID 1.3.6.1.4.1.710.3.2.1.2.9 displaystring read-only
This attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.
                         brzApRedundancySupport 1.3.6.1.4.1.710.3.2.1.2.10 integer read-write
Setting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no multicast or unicast frames for the cell arrive from the Ethernet during a period of 100 seconds. This option is available ONLY on AP (na value assigned in non-AP devices). Enumeration: 'on': 1, 'off': 2, 'na': 255.
                         brzWlanRelayUnicast 1.3.6.1.4.1.710.3.2.1.2.11 integer read-write
This attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's. Enumeration: 'on': 1, 'off': 2, 'na': 255.
                         brzWlanRelayBroadcast 1.3.6.1.4.1.710.3.2.1.2.12 integer read-write
This attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broadcast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's. Enumeration: 'on': 1, 'off': 2, 'na': 255.
                         brzApRedundancyLimit 1.3.6.1.4.1.710.3.2.1.2.13 integer read-write
This attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast frames for the cell arrive from the Ethernet. This option is available ONLY on AP (na value assigned in non-AP devices). Enumeration: 'na': 255.
                         brzStaNumForLargeCW 1.3.6.1.4.1.710.3.2.1.2.14 integer read-write
This attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will use the default CW. (The value is in the range of 1-120)
                         brzPowerMngMode 1.3.6.1.4.1.710.3.2.1.2.15 integer read-write
This attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of operation), and POWER SAVE. An STA will always return an ACTIVE value. Enumeration: 'disabled': 1, 'enabled': 2.
                         brzACKDelayed 1.3.6.1.4.1.710.3.2.1.2.16 integer read-write
This attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network. Enumeration: 'on': 1, 'off': 2.
                         brzDTIMPperiod 1.3.6.1.4.1.710.3.2.1.2.17 integer read-write
This attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in AP's.
                         brzPowerMngBitTestMode 1.3.6.1.4.1.710.3.2.1.2.18 integer read-write
This attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode of operation), and ENABLED. Enumeration: 'disabled': 1, 'enabled': 2.
                         brzBeaconInterval 1.3.6.1.4.1.710.3.2.1.2.19 integer read-write
This attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's.
                         brzPowerSaveSupport 1.3.6.1.4.1.710.3.2.1.2.20 integer read-write
This attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Save support with PM bit test This attribute is applicable only in AP's. Enumeration: 'disabled': 0, 'enabled-with-pm-bit': 2, 'enabled': 1.
                         brzWlanAssocAge 1.3.6.1.4.1.710.3.2.1.2.21 integer read-write
This attribute defines the Association Aging Period.
                         brzEnableVoice 1.3.6.1.4.1.710.3.2.1.2.22 integer read-write
This attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's. Enumeration: 'enable': 1, 'disable': 0.
                         brzNonActiveCodeState 1.3.6.1.4.1.710.3.2.1.2.26 displaystring read-only
This attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in station throughput, also answer is delayed!!!
                         brzDisplayNonActiveCodeVersion 1.3.6.1.4.1.710.3.2.1.2.27 displaystring read-only
This attribute displays the active code version and the non active code version.
                         brzIntelligentBridgingPeriod 1.3.6.1.4.1.710.3.2.1.2.28 integer read-write
This attribute defines the Intelligent Bridging Period in seconds.
                 ipParams 1.3.6.1.4.1.710.3.2.2
                     trapHostsTable 1.3.6.1.4.1.710.3.2.2.1 no-access
A list of trap-hosts entries.
                         trapHostsEntry 1.3.6.1.4.1.710.3.2.2.1.1 no-access
A trap-receiving host entry, containing trap-host objects for a particular host.
                             trapHostsIndex 1.3.6.1.4.1.710.3.2.2.1.1.1 integer read-only
A unique value for each trap-host. Its value ranges between 1 and 3
                             trapIPaddress 1.3.6.1.4.1.710.3.2.2.1.1.2 ipaddress read-write
The IP address of the host to be sent all traps
                             trapCommunity 1.3.6.1.4.1.710.3.2.2.1.1.3 displaystring read-write
The community of the host to be sent all traps
                     ipAddr 1.3.6.1.4.1.710.3.2.2.2 ipaddress read-write
The IP address of this device, used to access the device through any of its LAN Ports (Ethernet or WLAN).
                     maskIP 1.3.6.1.4.1.710.3.2.2.3 ipaddress read-write
The IP Network mask used by the IP entity when accessing devices through any of its LAN Ports (Ethernet or WLAN).
                     readCommunity 1.3.6.1.4.1.710.3.2.2.4 displaystring read-write
The device read community. If updated, it will be used after the next reset.
                     writeCommunity 1.3.6.1.4.1.710.3.2.2.5 displaystring read-write
The device write community. If updated, it will be used after the next reset.
                     gatewayIPaddr 1.3.6.1.4.1.710.3.2.2.6 ipaddress read-write
Gateway default IP address.
                     brzIPStack 1.3.6.1.4.1.710.3.2.2.7 integer read-write
This attribute defines whether to use IP stack or not. Enumeration: 'disabled': 1, 'enabled': 0.
                 brzWlan 1.3.6.1.4.1.710.3.2.3
                     brzWlanParams 1.3.6.1.4.1.710.3.2.3.1
                         brzMaxRate 1.3.6.1.4.1.710.3.2.3.1.1 integer read-write
This attribute indicates the rate (in Mbits per second) at which data will be transmitted across the medium. The default value of this attribute shall be 3.
                         brzMobilLvl 1.3.6.1.4.1.710.3.2.3.1.2 integer read-write
This attribute indicates the expected mobility level of the system. The default value of this attribute is stationary. Enumeration: 'high': 3, 'medium': 2, 'low': 1.
                         brzAvrgRssi 1.3.6.1.4.1.710.3.2.3.1.3 integer read-only
A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of 255). Enumeration: 'na': 255.
                         brzWlanProtocol 1.3.6.1.4.1.710.3.2.3.1.4 integer read-write
This attribute specifies the MAC/PHY protocol, utilized by this system. This attribute is not write accessible for regular users.
                         brzWlanTrapThreashold 1.3.6.1.4.1.710.3.2.3.1.5 integer read-write
This attribute specifies a threshold value, for sending the WlanStatusTRAP. When the Wireless LAN quality drops below (or goes above) this value, a trap will be issued.
                         brzWlanQuality 1.3.6.1.4.1.710.3.2.3.1.6 integer read-only
A measure for quality (and noise level) of the Wireless LAN. Enumeration: 'unknown': 10, 'medium': 3, 'good': 2, 'bad': 4, 'excellent': 1.
                         knownAPsTable 1.3.6.1.4.1.710.3.2.3.1.7 no-access
A table of identities of the most recently known Access Points, and their signal quality.
                             knownAPsEntry 1.3.6.1.4.1.710.3.2.3.1.7.1 no-access
An entry in the Known APs table.
                                 knownAPsIndex 1.3.6.1.4.1.710.3.2.3.1.7.1.1 integer read-only
A unique value, representing the index of the AP in the Known APs table
                                 knownAPsValue 1.3.6.1.4.1.710.3.2.3.1.7.1.2 macaddress read-write
This attributes specifies the address of a recently known AP. The default value of this attribute shall be null (an empty entry).
                                 knownAPsQuality 1.3.6.1.4.1.710.3.2.3.1.7.1.3 integer read-only
This attribute specifies the current reception quality of frames, transmitted by that AP. At a station, a GOOD value indicates that the station can join that AP. Enumeration: 'poor': 1, 'unknown': 10, 'good': 2.
                                 knownAPsAvrgRssi 1.3.6.1.4.1.710.3.2.3.1.7.1.4 integer read-only
A value representing the average Signal Strength for packets received from that AP in RSSI units.
                                 knownAPsStatus 1.3.6.1.4.1.710.3.2.3.1.7.1.5 integer read-write
The validity of the current entry, either invalid or valid. Enumeration: 'valid': 1, 'invalid': 2.
                                 knownAPsLoadStations 1.3.6.1.4.1.710.3.2.3.1.7.1.6 integer read-only
A value representing the number of stations associated to that AP.
                                 knownAPsGoodBeacons 1.3.6.1.4.1.710.3.2.3.1.7.1.7 integer read-only
A value representing the number of beacons received with Strength more then join level from that AP.
                                 knownAPsTotalBeacons 1.3.6.1.4.1.710.3.2.3.1.7.1.8 integer read-only
A value representing the total number of beacons (good and bad) received from that AP.
                                 knownAPsAvrgDbm 1.3.6.1.4.1.710.3.2.3.1.7.1.9 displaystring read-only
A value representing the average Signal Strength for packets received from that AP in DBN units.
                         brzLastBeacon 1.3.6.1.4.1.710.3.2.3.1.8 integer read-only
A value representing last dwell to receive beacon from that AP.
                         brzBadBeacons 1.3.6.1.4.1.710.3.2.3.1.9 integer read-only
A value representing the number of beacons received with Strength less then join level from that AP.
                         brzLoadStations 1.3.6.1.4.1.710.3.2.3.1.10 integer read-only
A value representing the number of stations associated to that AP.
                         brzAvrgDBm 1.3.6.1.4.1.710.3.2.3.1.11 displaystring read-only
A value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of -255).
                     brzAP 1.3.6.1.4.1.710.3.2.3.2
                         bssInfo 1.3.6.1.4.1.710.3.2.3.2.1
                             bssNumOfStations 1.3.6.1.4.1.710.3.2.3.2.1.1 integer read-only
This attribute specifies the number of devices, that are currently associated with this AP.
                             bssNumOfStationsPeak 1.3.6.1.4.1.710.3.2.3.2.1.2 integer read-only
This attribute contains the maximum value that bssNumOfStations has reached.
                             bssCollectPerStationInfo 1.3.6.1.4.1.710.3.2.3.2.1.3 integer read-write
When this attribute is set to ON, the AP accumulates Wireless Link statistics per each station. This option is available only for the AP. At stations it is always assigned with na (Not Applicable) value. WARNING: Setting this attribute to ON can cause substantial degradation in cell throughput!!! Enumeration: 'on': 1, 'off': 2, 'na': 255.
                             bssNumOfBeaconSent 1.3.6.1.4.1.710.3.2.3.2.1.4 integer read-only
This attribute contains the total beacons sent counter.
                             bssNumOfBeaconLost 1.3.6.1.4.1.710.3.2.3.2.1.5 integer read-only
This attribute contains the total beacons lost counter.
                             bssNumOfStationsAuthenticated 1.3.6.1.4.1.710.3.2.3.2.1.6 integer read-only
This attribute specifies the number of devices, that are currently Authenticated with this AP.
                             bssNumOfStationsAuthenticatedPeak 1.3.6.1.4.1.710.3.2.3.2.1.7 integer read-only
This attribute contains the maximum value that bssNumOfStationsAuthenticated has reached.
                         bssApAdb 1.3.6.1.4.1.710.3.2.3.2.2
                             adbTable 1.3.6.1.4.1.710.3.2.3.2.2.1 no-access
A table of the stations associated.
                                 adbEntry 1.3.6.1.4.1.710.3.2.3.2.2.1.1 no-access
An entry in ADB table.
                                     stAddress 1.3.6.1.4.1.710.3.2.3.2.2.1.1.1 macaddress read-only
The MAC Address of the station represented by this entry in the Association Data Base
                                     stCFMode 1.3.6.1.4.1.710.3.2.3.2.2.1.1.4 integer read-only
This attribute is set to ON if the station is in the Contention Free Polling list of the AP. Enumeration: 'on': 1, 'off': 2.
                                     stMaxRate 1.3.6.1.4.1.710.3.2.3.2.2.1.1.5 integer read-only
This attribute indicates the maximum rate (in Mbits per second) at which that station transmits data across the Wireless medium.
                                     stCurTxRate 1.3.6.1.4.1.710.3.2.3.2.2.1.1.6 integer read-only
The rate currently used by the AP to transmit packets to this station
                                     stRssi 1.3.6.1.4.1.710.3.2.3.2.2.1.1.7 integer read-only
A value representing the average Signal Strength for packets received from that station in RSSI units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.
                                     stPMMode 1.3.6.1.4.1.710.3.2.3.2.2.1.1.8 integer read-only
The current Power Management mode of this station Power saving mode enables WLAN units (such as laptops or hand-held devices) to conserve battery power. To enable this feature, first enable power saving for the AP, and then enable power saving in the SA-PCR Card. Enumeration: 'active': 1, 'power-saved': 2.
                                     stTxFragments 1.3.6.1.4.1.710.3.2.3.2.2.1.1.9 counter read-only
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stTxFragments1M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.10 counter read-only
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stTxFragments2M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.11 counter read-only
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stTxFragments3M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.12 counter read-only
This attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 3Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stTxRetry 1.3.6.1.4.1.710.3.2.3.2.2.1.1.13 counter read-only
This attribute counts the total number of retransmissions to that station, over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stTxDroppedPackets 1.3.6.1.4.1.710.3.2.3.2.2.1.1.14 counter read-only
This attribute counts the number of transmit frames (data or management) to this station, that were dropped because of too many retransmissions. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stRxFragments 1.3.6.1.4.1.710.3.2.3.2.2.1.1.15 counter read-only
This attribute counts the total number of fragments (data and management) that have been received successfully from that station, through the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stWlanStatus 1.3.6.1.4.1.710.3.2.3.2.2.1.1.16 integer read-only
This attribute specifies the current reception quality of frames, transmitted by that station. Enumeration: 'poor': 1, 'unknown': 10, 'good': 2.
                                     stResetCounters 1.3.6.1.4.1.710.3.2.3.2.2.1.1.17 integer read-write
Setting the value of this attribute to ON, will clear the station counters at the AP (clear the counters in that adbEntry). Warning: Setting the value of this attribute to ON may cause momentary degradation in performance Enumeration: 'on': 1, 'off': 2.
                                     stType 1.3.6.1.4.1.710.3.2.3.2.2.1.1.18 integer read-only
This attribute identifies the device type of the station. Enumeration: 'sa-40': 3, 'unknown': 6, 'sa-10': 1, 'breeze-new': 5, 'sa-pc': 4, 'wb-10': 2.
                                     stTxRetryPercent 1.3.6.1.4.1.710.3.2.3.2.2.1.1.19 counter read-only
This attribute calculate the retransmitted percentage, that was retransmitted to that station over the Wireless LAN.
                                     stReTxFragments1M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.20 counter read-only
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stReTxFragments2M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.21 counter read-only
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stReTxFragments3M 1.3.6.1.4.1.710.3.2.3.2.2.1.1.22 counter read-only
This attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.
                                     stDbm 1.3.6.1.4.1.710.3.2.3.2.2.1.1.23 displaystring read-only
A value representing the average Signal Strength for packets received from that station in DBM units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.
                     brzSTA 1.3.6.1.4.1.710.3.2.3.3
                         brzCurrentAPMacAddress 1.3.6.1.4.1.710.3.2.3.3.1 macaddress read-only
Hardware MAC address of the AP currently associated with. Available ONLY in station.
                         brzLastAPMacAddress 1.3.6.1.4.1.710.3.2.3.3.2 macaddress read-only
The Hardware MAC address of the last AP that the station was associated with. Available ONLY in stations.
                         brzPreferredAPMacAddress 1.3.6.1.4.1.710.3.2.3.3.3 macaddress read-write
The Hardware MAC address of the preferred AP, to which the station should associate when ever possible. Null value here indicates no preferences. Available ONLY in stations.
                         brzRoamToAPMacAddress 1.3.6.1.4.1.710.3.2.3.3.4 macaddress read-write
Setting this attribute to a specific AP MAC address, will cause the station to roam immediately to that AP, if possible. Available ONLY for stations.
                         brzCFMode 1.3.6.1.4.1.710.3.2.3.3.5 integer read-only
This attribute is set to ON if the station required Contention Free services from the AP (hence it is in the AP's Contention Free list). This option is available ONLY on stations. A Not Applicable value is returned for all APs. Enumeration: 'on': 1, 'off': 2, 'na': 255.
                         brzTx1MBitRate 1.3.6.1.4.1.710.3.2.3.3.6 counter read-only
Total transmitted frames in 1 MBit rate.
                         brzTx2MBitRate 1.3.6.1.4.1.710.3.2.3.3.7 counter read-only
Total transmitted frames in 2 MBit rate.
                         brzTx3MBitRate 1.3.6.1.4.1.710.3.2.3.3.8 counter read-only
Total transmitted frames in 3 MBit rate.
                         brzTotalRetx 1.3.6.1.4.1.710.3.2.3.3.9 macaddress read-only
Total Retransmitted frames including all rates.
                     brzRoamParams 1.3.6.1.4.1.710.3.2.3.4
                         brzRoamDecisionWin 1.3.6.1.4.1.710.3.2.3.4.1 integer read-write
This parameter defines a minimum number of RSSI samples which is required to make a decision about the current WLAN channel quality. A new RSSI sample arrives with each incoming frame. Available ONLY in stations.
                         brzRoamDecisionNumerator 1.3.6.1.4.1.710.3.2.3.4.2 integer read-write
This parameter defines a maximum number of RSSI samples that is allowed to be below brzRoamDecisionRSSIThreshold, among a number equal to brzRoamDecisionWin of the last arrived samples. If a number of bad samples (i.e. below brzRoamDecisionRSSIThreshold) exceeds one, which is defined by this parameter, the channel is considered as bad. Available ONLY in stations.
                         brzRoamDecisionRSSIThreshold 1.3.6.1.4.1.710.3.2.3.4.3 integer read-write
If an RSSI sample is bellow the value which is defined by this parameter the sample is considered as bad. Available ONLY in stations.
                         brzJoinDecisionRSSIThreshold 1.3.6.1.4.1.710.3.2.3.4.4 integer read-write
A station will join a new AP only if the AP transmits with an RSSI quality above the value which is defined by this parameter. Available ONLY in stations. In AP's, this is the threshold for sending Bad WLAN Conditions traps. If a station associated with the AP is heard at an RSII level below this threshold, a Bad WLAN Conditions trap is sent by the AP.
                         brzNeighboringBeacons 1.3.6.1.4.1.710.3.2.3.4.5 integer read-write
This parameters defines once in how many dwell times the AP will send a neighboring beacon. Available ONLY in AP's.
                         brzNumberOfProbeResponses 1.3.6.1.4.1.710.3.2.3.4.6 integer read-write
If a number of good RSSI samples coming from a neighbor is greater than or equal to this parameter the neighbor might be selected for joining.
                         brzNumberOfBeaconsForDisconnect 1.3.6.1.4.1.710.3.2.3.4.7 integer read-write
This parameter defines a maximum number of consecutive not arrived Beacons that is allowed before a disconnect decision. Available ONLY in stations.
                         brzMaxNumberOfScanning 1.3.6.1.4.1.710.3.2.3.4.8 integer read-write
This parameter defines a maximum number of scanning Attempts to perform before system reset. Zero is value for non reset. Available ONLY in stations.
                         brzNeighboringBeaconRate 1.3.6.1.4.1.710.3.2.3.4.9 integer read-write
This parameter defines the Neighboring Beacon Rate in dwells. Zero is value for non Neighboring Beacons. Available ONLY in AP's.
                 brzCnt 1.3.6.1.4.1.710.3.2.4
                     brzDSCnt 1.3.6.1.4.1.710.3.2.4.1
                         brzRxFromDS 1.3.6.1.4.1.710.3.2.4.1.1 counter read-only
This attribute counts the total number of frames that have been received successfully from the Wired Distribution system.
                         brzRxBadFromDS 1.3.6.1.4.1.710.3.2.4.1.2 counter read-only
This attribute counts the number errored frames, received from the Wired Distribution system.
                         brzRxOctetsFromDS 1.3.6.1.4.1.710.3.2.4.1.3 counter read-only
This attribute counts the total number of octets that have been received successfully from the Wired Distribution system.
                         brzTxToDS 1.3.6.1.4.1.710.3.2.4.1.4 counter read-only
This attribute counts the total number of frames that have been transmitted to the Wired Distribution system.
                         brzMissedFrames 1.3.6.1.4.1.710.3.2.4.1.5 counter read-only
This attribute counts the total number of missed frames that have missed the transmission to the Ethernet LAN.
                         brzTxOctetsToDS 1.3.6.1.4.1.710.3.2.4.1.6 counter read-only
This attribute counts the total number of octets that have been transmitted successfully to the Wired Distribution system.
                         brzRxOctetsForwardToWlan 1.3.6.1.4.1.710.3.2.4.1.7 counter read-only
This attribute counts the total number of octets that have been transmitted successfully to the Wireless LAN.
                         brzRxForwardToWlan 1.3.6.1.4.1.710.3.2.4.1.8 counter read-only
This attribute counts the total number of packets that have been transmitted successfully to the Wireless LAN.
                     brzWlanCnt 1.3.6.1.4.1.710.3.2.4.2
                         brzTxWlanCnt 1.3.6.1.4.1.710.3.2.4.2.1
                             brzTxPacketsToWlan 1.3.6.1.4.1.710.3.2.4.2.1.1 counter read-only
This attribute counts the total number of frames (data and management) that have been transmitted to the Wireless LAN.
                             brzTxMSDUToWlan 1.3.6.1.4.1.710.3.2.4.2.1.2 counter read-only
This attribute counts the total number of frames (data frames) that have been transmitted to the Wireless LAN.
                             brzDiscarded 1.3.6.1.4.1.710.3.2.4.2.1.3 counter read-only
This attribute counts the number of data frames, that were internally discarded in the system, instead of being transmitted over the Wireless LAN. High values of this counter indicate either very high traffic volume, or a noisy environment that prevents Wireless transmissions.
                             brzTxFragToWlan 1.3.6.1.4.1.710.3.2.4.2.1.4 counter read-only
This attribute counts the total number of fragments (data and management) that have been transmitted to the Wireless LAN.
                             brzRetryOnWlan 1.3.6.1.4.1.710.3.2.4.2.1.5 counter read-only
This attribute counts the total number of retransmitted fragments, on the Wireless LAN.
                             brzFailedCountOnWlan 1.3.6.1.4.1.710.3.2.4.2.1.6 counter read-only
This attribute counts the number of frames that were dropped (not transmitted), due to the number of retransmits attempts exceeding the RetryMax value.
                             brzRetryOnWlanPercent 1.3.6.1.4.1.710.3.2.4.2.1.7 counter read-only
This attribute calculates the percentage of number frames (to the data and management) that have been transmitted successfully Wireless LAN.
                             brzRetryTxDataToWlan 1.3.6.1.4.1.710.3.2.4.2.1.8 counter read-only
This attribute counts the total number of data frames that have been retransmitted to the Wireless LAN.
                             brzRetryTxDataToWlanPercent 1.3.6.1.4.1.710.3.2.4.2.1.9 counter read-only
This attribute calculates the percentage of data frames that have been transmitted successfully to the Wireless LAN.
                             brzTotalTxPacketsToWlan 1.3.6.1.4.1.710.3.2.4.2.1.10 counter read-only
This attribute counts the total number frames (data and management) that have been transmitted to the Wireless LAN.
                             brzTxErrTransmitions 1.3.6.1.4.1.710.3.2.4.2.1.15
                                   brzTxErrorAckTimeOut 1.3.6.1.4.1.710.3.2.4.2.1.15.1 counter read-only
This attribute counts the total number of acknowledge timeouts on the Wireless LAN.
                                   brzTxErrorAckCRC 1.3.6.1.4.1.710.3.2.4.2.1.15.2 counter read-only
This attribute counts the total number of acknowledge CRC Errors on the Wireless LAN.
                                   brzTxErrorNoTimeUntilHop 1.3.6.1.4.1.710.3.2.4.2.1.15.3 counter read-only
This attribute counts the total number of timeouts caused of on time until end of hop on the Wireless Cell.
                                   brzTxErrorUnderRunAndCTS 1.3.6.1.4.1.710.3.2.4.2.1.15.4 counter read-only
This attribute counts the total number of errors caused by HW problems (Under Run).
                                   brzTxErrorAbort 1.3.6.1.4.1.710.3.2.4.2.1.15.5 counter read-only
This attribute counts the total number of errors caused by frame abortion from Boori.
                                   brzTxErrorFrameReceived 1.3.6.1.4.1.710.3.2.4.2.1.15.6 counter read-only
This attribute counts the total number of errors caused by frame failure on the Wireless LAN.
                         brzRxWlanCnt 1.3.6.1.4.1.710.3.2.4.2.2
                             brzRxPacketsFromWlan 1.3.6.1.4.1.710.3.2.4.2.2.1 counter read-only
This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN.
                             brzRxMSDUFromWlan 1.3.6.1.4.1.710.3.2.4.2.2.2 counter read-only
This attribute counts the total number of MSDUs (data frames) that have been received successfully from the Wireless LAN.
                             brzRxFragFromWlan 1.3.6.1.4.1.710.3.2.4.2.2.3 counter read-only
This attribute counts the number of fragments (data and management), that have been received successfully from the Wireless LAN.
                             brzRxBadFragFromWlan 1.3.6.1.4.1.710.3.2.4.2.2.4 counter read-only
This counter is incremented when an error is detected in a fragment, received from the Wireless LAN.
                             brzRxDuplicateFragFromWlan 1.3.6.1.4.1.710.3.2.4.2.2.5 counter read-only
This counter is incremented when a duplicated fragment is received from the Wireless LAN.
                             freqStatisticsTable 1.3.6.1.4.1.710.3.2.4.2.2.6 no-access
A table for the traffic statistics of each frequency.
                                 freqStatisticsEntry 1.3.6.1.4.1.710.3.2.4.2.2.6.1 no-access
An entry in the Frequencies Statistics table.
                                     freqStatisticsIndex 1.3.6.1.4.1.710.3.2.4.2.2.6.1.1 integer read-only
A unique value, representing the index of the frequency in the hopping sequence table
                                     freqNo 1.3.6.1.4.1.710.3.2.4.2.2.6.1.2 integer read-only
This attributes specifies the channel number of the frequency, for which this entry accumulates the statistics.
                                     freqTotalReceived 1.3.6.1.4.1.710.3.2.4.2.2.6.1.3 counter read-only
This attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN, in that specific frequency.
                     brzRoamCnt 1.3.6.1.4.1.710.3.2.4.3
                         brzNumOfReassocRequests 1.3.6.1.4.1.710.3.2.4.3.1 counter read-only
For an AP: The number of Associations and ReAssociations requests, received since the last reset of the AP. This counter is useful for getting information about mobility activity on the BSS. For a Station: The number of Associations and ReAssociation requests issued by the station since the last reset.
                     brzMngCnt 1.3.6.1.4.1.710.3.2.4.4
                         brzMngAP 1.3.6.1.4.1.710.3.2.4.4.1
                             probeResponseSent 1.3.6.1.4.1.710.3.2.4.4.1.1 counter read-only
For an AP: Number of Probe response that sent.
                             probeResponseLost 1.3.6.1.4.1.710.3.2.4.4.1.2 counter read-only
For an AP: Number of Probe response that got lost.
                             probeResponseSentRetx 1.3.6.1.4.1.710.3.2.4.4.1.3 counter read-only
For an AP: Number of retransmitted Probe response frames that sent.
                             probeRequestRecive 1.3.6.1.4.1.710.3.2.4.4.1.4 counter read-only
For an AP: Number of Probe request frames that has received.
                             assocResponseSent 1.3.6.1.4.1.710.3.2.4.4.1.5 counter read-only
For an AP: Number of Association response frames that sent.
                             assocResponseLost 1.3.6.1.4.1.710.3.2.4.4.1.6 counter read-only
For an AP: Number of Association response frames that got lost.
                             assocResponseSentRetx 1.3.6.1.4.1.710.3.2.4.4.1.7 counter read-only
For an AP: Number of retransmitted Association response frames that sent.
                             assocRequestRecive 1.3.6.1.4.1.710.3.2.4.4.1.8 counter read-only
For an AP: Number of Association request frames that has received.
                             reAssocRequestRecive 1.3.6.1.4.1.710.3.2.4.4.1.9 counter read-only
For an AP: Number of ReAssociation request frames that has received.
                         brzMngSAWB 1.3.6.1.4.1.710.3.2.4.4.2
                             probRequestSent 1.3.6.1.4.1.710.3.2.4.4.2.1 counter read-only
For WB or SA: Number of Probe request frames that sent.
                             probResponceRecive 1.3.6.1.4.1.710.3.2.4.4.2.2 counter read-only
For WB or SA: Number of received Probe response frames.
                             authRequestSent 1.3.6.1.4.1.710.3.2.4.4.2.3 counter read-only
For WB or SA: Number of Authentication request frames that sent.
                             authRequestSentRetx 1.3.6.1.4.1.710.3.2.4.4.2.4 counter read-only
For WB or SA: Number of Retransmitted Authentication request frames that sent.
                             authResponceRecive 1.3.6.1.4.1.710.3.2.4.4.2.5 counter read-only
For WB or SA: Number of received Authentication response frames.
                             assocRequestSent 1.3.6.1.4.1.710.3.2.4.4.2.6 counter read-only
For WB or SA: Number of Association request frames that sent.
                             assocRequestSentRetx 1.3.6.1.4.1.710.3.2.4.4.2.7 counter read-only
For WB or SA: Number of Retransmitted Association request frames that sent.
                             assocResponceRecive 1.3.6.1.4.1.710.3.2.4.4.2.8 counter read-only
For WB or SA: Number of received Association response frames.
                     brzPSCnt 1.3.6.1.4.1.710.3.2.4.5
                         pSFreeEntries 1.3.6.1.4.1.710.3.2.4.5.1 counter read-only
For an AP: Number of station free entries.
                         pSInternallydiscarded 1.3.6.1.4.1.710.3.2.4.5.2 counter read-only
For an AP: Number of Internally Discarded frames.
                         pSstations 1.3.6.1.4.1.710.3.2.4.5.3 counter read-only
For an AP: Number of power saved station connected to this AP.
                         pSPowerSavingAged 1.3.6.1.4.1.710.3.2.4.5.4 counter read-only
For an AP: Number of frames that were not transmitted due to the end of aging time.
                         powreStationsTable 1.3.6.1.4.1.710.3.2.4.5.5 no-access
A list of trap-hosts entries.
                             powreStationsEntry 1.3.6.1.4.1.710.3.2.4.5.5.1 no-access
A trap-receiving host entry, containing trap-host objects for a particular host.
                                 powerSaveIndex 1.3.6.1.4.1.710.3.2.4.5.5.1.1 integer read-only
A unique value, representing the index of the frequency in the hopping sequence table
                                 powerSaveStationID 1.3.6.1.4.1.710.3.2.4.5.5.1.2 integer read-only
The identifier numerator of the Station in the AP. Note : ID zero is Broadcast.
                                 powerSaveBuffered 1.3.6.1.4.1.710.3.2.4.5.5.1.3 integer read-only
This attributes specifies how many messages are waiting to that Station in the AP buffers
                                 powerSaveAged 1.3.6.1.4.1.710.3.2.4.5.5.1.4 integer read-only
This attributes specifies how many Stations were deleted after long time of waiting
                                 powerSaveSent 1.3.6.1.4.1.710.3.2.4.5.5.1.5 integer read-only
This attributes specifies how many messages were sent to that station
                                 powerSaveQueueFull 1.3.6.1.4.1.710.3.2.4.5.5.1.6 integer read-only
This attributes specifies how many messages were discarded because the queue to that station was full
                 brzTraps 1.3.6.1.4.1.710.3.2.5
                     brzTrapAPMacAddr 1.3.6.1.4.1.710.3.2.5.1 macaddress read-only
The MAC address of an AP
                     brzTrapSTAMacAddr 1.3.6.1.4.1.710.3.2.5.2 macaddress read-only
The MAC address of a station device
                     brzTrapMacAddress 1.3.6.1.4.1.710.3.2.5.3 macaddress read-only
A STA or AP MAC address
                     brzTrapRssiQuality 1.3.6.1.4.1.710.3.2.5.4 integer read-only
The RSSI level of the signal received from the Access Point
                     brzTrapLastRssiQuality 1.3.6.1.4.1.710.3.2.5.5 integer read-only
The RSSI level of the signal received from the previous Access Point
                     brzTrapIndex 1.3.6.1.4.1.710.3.2.5.6 integer read-only
Index number for future trap implementation
                     brzTrapText 1.3.6.1.4.1.710.3.2.5.7 displaystring read-only
Textual string for future trap implementation
                     brzTrapToggle 1.3.6.1.4.1.710.3.2.5.8 integer read-only
A general ON/OFF toggle value, for the traps. Enumeration: 'on': 1, 'off': 2.
                     brzTrapSTAType 1.3.6.1.4.1.710.3.2.5.9 integer read-only
This attribute identifies the device type of the station. Enumeration: 'sa40': 3, 'unknown': 6, 'wb10': 2, 'breeze-new': 5, 'sa-pc': 4, 'sa10': 1.
                 brzdot11 1.3.6.1.4.1.710.3.2.6
                     dot11smt 1.3.6.1.4.1.710.3.2.6.1
                         dot11DefaultWEPKeys 1.3.6.1.4.1.710.3.2.6.1.3
                             dot11DefaultWEPKey1 1.3.6.1.4.1.710.3.2.6.1.3.1 displaystring read-write
This attribute indicates the WEP secret key value corresponding to KeyID 1. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
                             dot11DefaultWEPKey2 1.3.6.1.4.1.710.3.2.6.1.3.2 displaystring read-write
This attribute indicates the WEP secret key value corresponding to KeyID 2. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
                             dot11DefaultWEPKey3 1.3.6.1.4.1.710.3.2.6.1.3.3 displaystring read-write
This attribute indicates the WEP secret key value corresponding to KeyID 3. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
                             dot11DefaultWEPKey4 1.3.6.1.4.1.710.3.2.6.1.3.4 displaystring read-write
This attribute indicates the WEP secret key value corresponding to KeyID 4. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).
                         dot11PrivacyGrp 1.3.6.1.4.1.710.3.2.6.1.6
                             dot11Preauthentication 1.3.6.1.4.1.710.3.2.6.1.6.1 integer read-write
This attribute, when true, enables Preauthentication algorithm. Enumeration: 'enable': 1, 'disable': 0.
                             dot11PrivacyOptionImplemented 1.3.6.1.4.1.710.3.2.6.1.6.2 integer read-only
This attribute, when true, shall indicate that the 802.11 WEP option is implemented. Enumeration: 'false': 2, 'true': 1.
                             dot11PrivacyInvoke 1.3.6.1.4.1.710.3.2.6.1.6.3 integer read-only
This attribute indicates if a special mechanism is invoked, to protect the Wireless LAN transmissions. The value is one of the following: 1 - Standard WEP, 2 - No Encryption, 20 - Special Encryption (#0), 21 - Special Encryption (#1), 22 - Special Encryption (#2)
                             dot11WEPDefaultKeyID 1.3.6.1.4.1.710.3.2.6.1.6.4 integer read-write
This attribute shall indicate the use of the first, second, third or fourth DefaultWEPKey when set to values of one, two, three or four.
                     dot11mac 1.3.6.1.4.1.710.3.2.6.2
                         dot11OperationGrp 1.3.6.1.4.1.710.3.2.6.2.1
                             dot11MaxMulticastRate 1.3.6.1.4.1.710.3.2.6.2.1.1 integer read-write
This attribute indicates the basic rate for multicast frames.
                             dot11DwellTime 1.3.6.1.4.1.710.3.2.6.2.1.2 integer read-write
This attribute indicates the dwell time in Kilo-microsecond Allowed Values for version 5.x.x and higher are between 19..390. For older versions values are between 1 - 3. This attribute is available only in AP's.
                             dot11RTSThreshold 1.3.6.1.4.1.710.3.2.6.2.1.3 integer read-write
This attribute indicates the number of bytes in an MPDU (frame), above which an RTS/CTS handshake will be performed. Setting this attribute to be larger than the maximum frame size, will prevent the RTS/CTS handshake for frames transmitted by this station.
                             dot11ShortRetryLimit 1.3.6.1.4.1.710.3.2.6.2.1.4 integer read-write
This attribute indicates the number of retransmission attempts made, before a failure condition is indicated. Values between 0..20 .
                             dot11DwellRetryLimit 1.3.6.1.4.1.710.3.2.6.2.1.5 integer read-write
This attribute indicates the number of retransmission attempts made in several Dwells, before a failure condition is indicated. Values between 0..9 .
                             dot11FragmentationThreshold 1.3.6.1.4.1.710.3.2.6.2.1.6 integer read-write
This attribute specifies the current maximum size, in octets, of the MPDU that will be delivered to the PHY. A frame will be broken into fragments if its size exceeds the value of this attribute, after adding MAC header and tailors. The value is one of the following: 1 - 560 octets, 2 - 800 octets, 3 - 1518 octets.
                             dot11ShortRetryLimitForVoice 1.3.6.1.4.1.710.3.2.6.2.1.7 integer read-write
This attribute indicates the number of retransmission for voice attempts made, before a failure condition is indicated. Values between 0..9 . This option is only for AP's.
                             dot11DwellRetryLimitForVoice 1.3.6.1.4.1.710.3.2.6.2.1.8 integer read-write
This attribute indicates the number of retransmission for voice attempts made in several Dwells, before a failure condition is indicated. Values between 0..5 . This option is only for AP's.
                     dot11res 1.3.6.1.4.1.710.3.2.6.3
                         dot11resAttribute 1.3.6.1.4.1.710.3.2.6.3.8
                             dot11ResourceInfo 1.3.6.1.4.1.710.3.2.6.3.8.2
                                 dot11CurrentStationStatus 1.3.6.1.4.1.710.3.2.6.3.8.2.1 displaystring read-only
This attribute identifies the current Station Wlan status. This attribute is not available in AP's.
                                 dot11TotalNumberOfAssocSinceLastReset 1.3.6.1.4.1.710.3.2.6.3.8.2.2 counter read-only
This attribute identifies how many time the device Associated since startup.
                                 dot11manufacturerName 1.3.6.1.4.1.710.3.2.6.3.8.2.3 displaystring read-only
This attribute identifies the manufacturer of the resource.
                                 dot11manufacturerProductName 1.3.6.1.4.1.710.3.2.6.3.8.2.4 displaystring read-only
This attribute identifies the manufacturer product name of the resource.
                                 dot11manufacturerProductVersion 1.3.6.1.4.1.710.3.2.6.3.8.2.5 displaystring read-only
This attribute identifies the manufacturer's product version of the resource.
                     dot11phy 1.3.6.1.4.1.710.3.2.6.4
                         dot11PhyOperationGrp 1.3.6.1.4.1.710.3.2.6.4.1
                             dot11CurrentRegDomain 1.3.6.1.4.1.710.3.2.6.4.1.3 integer read-write
This attribute specifies the regularity domain, for the radio operation of this device. This integer contains an 8 bit value, as defined below: 00h - EthAirNet, 10h - USA, 20h - Canada, 30h - Europe, 31h - Spain, 32h - France, 37h - Europe Double Deviation, 38h - Netherlands, 40h - Japan, 41h - Korea, 48h - Israel, 49h - Australia, 60h - Proprietary. Enumeration: 'canada': 32, 'europe': 48, 'israel': 72, 'netherlands': 56, 'proprietary': 96, 'europe-dd': 55, 'usa': 16, 'france': 50, 'ethairnet': 0, 'australia': 73, 'korea': 65, 'japan': 64, 'spain': 49.
                         dot11PhyAntennaGrp 1.3.6.1.4.1.710.3.2.6.4.3
                             dot11CurrentTxAntenna 1.3.6.1.4.1.710.3.2.6.4.3.2 integer read-write
This attribute specifies the current antenna being used to transmit. The value is one of the following: 0 - Intelligent antennas selection, 1 - Transmitting only with antenna 1, 2 - Transmitting always with antenna 2.
                         dot11PhyTxPwrGrp 1.3.6.1.4.1.710.3.2.6.4.4
                             dot11CurrentTxPwrLvl 1.3.6.1.4.1.710.3.2.6.4.4.11 integer read-write
This attribute specifies the power level, currently being used to transmit data. The value is one of the following: 0 - Low, or 1 - High. Enumeration: 'high': 1, 'low': 0.
                         dot11PhyFHSSGrp 1.3.6.1.4.1.710.3.2.6.4.5
                             dot11CurrentDwellTime 1.3.6.1.4.1.710.3.2.6.4.5.5 integer read-write
This attribute specifies the current time, in Kilo-microseconds, that the radio operates on a single channel. The value is from 19 - 390. The same Dwell Time value should be assigned to all the devices within the same Wireless LAN network.
                             dot11CurrentSet 1.3.6.1.4.1.710.3.2.6.4.5.6 integer read-write
This attribute represents the current set of patterns that the device is using to determine the hop sequence. The range of values is 1 to 3, and the default is 1.
                             dot11CurrentPattern 1.3.6.1.4.1.710.3.2.6.4.5.7 integer read-write
This attribute represents the current pattern that the device is using to determine the hop sequence.
                     dot11MultySupport 1.3.6.1.4.1.710.3.2.6.5
                         dot11MultyRateSupport 1.3.6.1.4.1.710.3.2.6.5.1 integer read-write
This attribute indicates the multi cast rate support. Enumeration: 'disabled': 0, 'enabled': 1.
                         dot11MultyRateDecisionWindow 1.3.6.1.4.1.710.3.2.6.5.2 integer read-write
This attribute indicates the multi cast rate decision window size.
                     dot11Maintenance 1.3.6.1.4.1.710.3.2.6.6
                         dot11WaitforAssociationAddress 1.3.6.1.4.1.710.3.2.6.6.1 integer read-write
This attribute indicates the station mac-address. 0 - Use mine 1 - Wait for update via Ethernet Available only for Stations. Enumeration: 'get-from-ethernet': 1, 'use-mine': 0.
                         dot11JapanCallSign 1.3.6.1.4.1.710.3.2.6.6.2 displaystring read-write
This attribute indicates the Japan call sign string. Available only for Japan Standard.
         breezecomOID 1.3.6.1.4.1.710.4
             breezecomAP10 1.3.6.1.4.1.710.4.1
             breezecomWB10 1.3.6.1.4.1.710.4.2
             breezecomSA10 1.3.6.1.4.1.710.4.3
             breezecomSA40 1.3.6.1.4.1.710.4.4
                   brzAProamingIn 1.3.6.1.4.1.710.4.10.1
A trap indicating that a station has roamed into this AP. It contains the MAC address of the associated station and the device type of that station.
                   brzAPassociated 1.3.6.1.4.1.710.4.10.2
An AP trap indicating that a new station was associated with this AP. It contains the MAC address of the associated station.
                   brzAPdisassociated 1.3.6.1.4.1.710.4.10.3
An AP trap indicating that the station dis-associated itself from the AP. The trap contains the MAC address of the disassociated station.
                   brzAPaging 1.3.6.1.4.1.710.4.10.4
An AP trap indicating that the station association was aged out, and removed from that AP. The trap contains the MAC address of the aging station
                   brzAProamedOut 1.3.6.1.4.1.710.4.10.5
An AP trap indicating that a given station has roamed out from this AP. The trap contains the MAC address of the roamed out station
                   brzAPWlanStatusap 1.3.6.1.4.1.710.4.10.7
An AP trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
                   brzWlanStatusOfStation 1.3.6.1.4.1.710.4.10.8
An AP trap, indicating a change in the quality of the Wireless connection, with a specific (associated) station. An ON value indicates a specially bad connection, and an OFF value is sent if the quality improves, exceeding a predetermined threshold value. The brzTrapMacAddress contains the MAC address of the applicable station.
                   brzGeneralAP 1.3.6.1.4.1.710.4.10.9
An AP general purpose trap, for future trap implementation.
                   brzWBassociated 1.3.6.1.4.1.710.4.20.6
A WB trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
                   brzWBWlanStatus 1.3.6.1.4.1.710.4.20.7
A WB trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
                   brzGeneralWB 1.3.6.1.4.1.710.4.20.9
A WB general purpose trap, for future trap implementation.
                   brzSTAassociated 1.3.6.1.4.1.710.4.30.6
A station trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
                   brzSTAWlanStatus 1.3.6.1.4.1.710.4.30.7
A STA trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
                   brzGeneralSTA 1.3.6.1.4.1.710.4.30.9
A STA general purpose trap, for future trap implementation.
                   brzSA40associated 1.3.6.1.4.1.710.4.40.6
A SA-40 trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros).
                   brzSA40WlanStatus 1.3.6.1.4.1.710.4.40.7
SA-40 trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent.
                   brzGeneralSA40 1.3.6.1.4.1.710.4.40.9
SA-40 general purpose trap, for future trap implementation.