ANNEX-MIB: View SNMP OID List / Download MIB

VENDOR: XYLOGICS


 Home MIB: ANNEX-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 xylogics 1.3.6.1.4.1.15
       prod 1.3.6.1.4.1.15.1
           prodannex 1.3.6.1.4.1.15.1.1 displaystring read-only
Product name.
       annex 1.3.6.1.4.1.15.2
           hw 1.3.6.1.4.1.15.2.1
               hwType 1.3.6.1.4.1.15.2.1.1 integer read-only
An identifier for the Annex hardware type. Enumeration: 'annexII': 16, 'microannex': 52, 'microels': 55, 'err': 1, 'annex3': 42.
               hwRev 1.3.6.1.4.1.15.2.1.2 displaystring read-only
The revision level of the hardware platform.
               romRev 1.3.6.1.4.1.15.2.1.3 displaystring read-only
The revision number of the ROM Monitor software.
               serialNumber 1.3.6.1.4.1.15.2.1.4 integer read-only
The serial number assigned to the unit.
               memorySize 1.3.6.1.4.1.15.2.1.5 integer read-only
The amount of memory present in the unit.
           sw 1.3.6.1.4.1.15.2.2
               swType 1.3.6.1.4.1.15.2.2.1 integer read-only
The software version currently running on the Annex. Enumeration: 'microannexux': 52, 'annex3mx': 43, 'err': 1, 'microannexmx': 53, 'annex3ux': 42, 'annexIImx': 16, 'microels': 55, 'annexIIux': 17.
               swRevMajor 1.3.6.1.4.1.15.2.2.2 integer read-only
The major software release number.
               swRevMinor 1.3.6.1.4.1.15.2.2.3 integer read-only
The minor software release number.
               swBuild 1.3.6.1.4.1.15.2.2.4 displaystring read-only
The full name of the software build, including the software version, major and minor version numbers and the date and time of the build.
               imageName 1.3.6.1.4.1.15.2.2.5 displaystring read-only
The name of the most recently booted image.
               bootHost 1.3.6.1.4.1.15.2.2.6 ipaddress read-only
The Internet address of the host from which the Annex booted.
               defaultDomain 1.3.6.1.4.1.15.2.2.7 displaystring read-only
The default domain name provided by the DNS nameserver.
               currentDate 1.3.6.1.4.1.15.2.2.8 displaystring read-only
The current date and time provided by the time server.
               usableMemory 1.3.6.1.4.1.15.2.2.9 integer read-only
The amount of available for data buffers and other structures after the Annex has booted.
               freeMemory 1.3.6.1.4.1.15.2.2.10 gauge read-only
The amount of currently available memory.
               minFreeMemory 1.3.6.1.4.1.15.2.2.11 integer read-only
The minimum amount of free memory since booting the Annex.
               cpuUtilization 1.3.6.1.4.1.15.2.2.12 gauge read-only
Percent of CPU time currently being used.
               maxProcs 1.3.6.1.4.1.15.2.2.13 integer read-only
The total number of process structures allocated for use.
               mostProcs 1.3.6.1.4.1.15.2.2.14 integer read-only
The maximum number of active processes since the Annex was booted.
               activeProcs 1.3.6.1.4.1.15.2.2.15 gauge read-only
The number of currently active processes.
               cpuIRescheds 1.3.6.1.4.1.15.2.2.16 gauge read-only
The number of processes whose time slice has expired in the last minute.
               cpuTRescheds 1.3.6.1.4.1.15.2.2.17 counter read-only
The total number of processes whose time slice has expired since booting the Annex.
               contextISwtchs 1.3.6.1.4.1.15.2.2.18 gauge read-only
The number of context switches in the last minute.
               contextTSwtchs 1.3.6.1.4.1.15.2.2.19 counter read-only
The total number of context switches since booting the Annex.
               cpuIActivates 1.3.6.1.4.1.15.2.2.20 gauge read-only
The number of processes that were activated in the last minute.
               cpuTActivates 1.3.6.1.4.1.15.2.2.21 counter read-only
The number of processes that were activated since booting the Annex.
               maxCallouts 1.3.6.1.4.1.15.2.2.22 integer read-only
The number of allocated Callout structures for timed events in the Annex.
               leastCallouts 1.3.6.1.4.1.15.2.2.23 integer read-only
The minimum number of Callout structures available since last booting the Annex.
               freeCallouts 1.3.6.1.4.1.15.2.2.24 gauge read-only
The current number of free Callout structures.
           ports 1.3.6.1.4.1.15.2.3
               totalPorts 1.3.6.1.4.1.15.2.3.1 integer read-only
The number of serial ports on this Annex.
               totalInChars 1.3.6.1.4.1.15.2.3.2 counter read-only
The total number of characters received on all serial ports.
               totalOutChars 1.3.6.1.4.1.15.2.3.3 counter read-only
The total number of characters transmitted on all serial ports.
               totalParityErrs 1.3.6.1.4.1.15.2.3.4 counter read-only
The total number of parity errors detected on all serial ports.
               totalOverrunErrs 1.3.6.1.4.1.15.2.3.5 counter read-only
The total number of overruns detected on all serial ports.
               totalFramingErrs 1.3.6.1.4.1.15.2.3.6 counter read-only
The total number of framing errors detected on all serial ports.
               portTable 1.3.6.1.4.1.15.2.3.7 no-access
Table of port entries.
                   portEntry 1.3.6.1.4.1.15.2.3.7.1 no-access
The port's configuration parameters.
                       anxpPortIndex 1.3.6.1.4.1.15.2.3.7.1.1 integer read-only
A unique number from 1 to totalPorts that identifies each serial port.
                       anxpMode 1.3.6.1.4.1.15.2.3.7.1.2 integer read-write
This parameter defines the mode for access to the serial line port. The default is cli Enumeration: 'dedicated': 6, 'slave': 2, 'cli': 1, 'unused': 4, 'ppp': 7, 'slip': 5, 'adaptive': 3.
                       anxpCtrlLines 1.3.6.1.4.1.15.2.3.7.1.3 integer read-write
The type of hardware control used on the port: modem control (dcddtr), flow control (ctsrts), or both. Enumeration: 'both': 4, 'none': 1, 'ctsrts': 3, 'dcddtr': 2.
                       anxpBidirModem 1.3.6.1.4.1.15.2.3.7.1.4 integer read-write
This parameter controls whether the port is configured for adaptive use with a bidirectional modem. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpAllowBcast 1.3.6.1.4.1.15.2.3.7.1.5 integer read-write
Controls whether the serial port can receive administrative broadcast messages. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpBcastDirection 1.3.6.1.4.1.15.2.3.7.1.6 integer read-write
Defines the direction that an administrative broadcast message is sent. This parameter is valid only when the port is defined as a slave port by the anxpMode parameter. Enumeration: 'port': 1, 'network': 2.
                       anxpInputStartChar 1.3.6.1.4.1.15.2.3.7.1.7 displaystring read-write
The control character sequence that restarts input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff.
                       anxpInputStopChar 1.3.6.1.4.1.15.2.3.7.1.8 displaystring read-write
The control character sequence that stops input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff.
                       anxpOutputStartChar 1.3.6.1.4.1.15.2.3.7.1.9 displaystring read-write
The control character sequence that restarts output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff.
                       anxpOutputStopChar 1.3.6.1.4.1.15.2.3.7.1.10 displaystring read-write
The control character sequence that stops output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff.
                       anxpIxanyFlowCtl 1.3.6.1.4.1.15.2.3.7.1.11 integer read-write
This parameter specifies whether any input character will be treated as a start (xon) character when output has been suspended by a stop (xoff) character. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpLongBreak 1.3.6.1.4.1.15.2.3.7.1.12 integer read-write
This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break greater than two seconds. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpShortBreak 1.3.6.1.4.1.15.2.3.7.1.13 integer read-write
This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break shorter than two seconds. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpForwardTimer 1.3.6.1.4.1.15.2.3.7.1.14 integer read-write
This parameter defines the inter-character timer that sets the amount of time, in tens of milliseconds, that will elapse before forwarding the received data. The value of zero turns off the timer.
                       anxpForwardCount 1.3.6.1.4.1.15.2.3.7.1.15 integer read-write
Specifies the number of received characters buffered for the port by the Annex before forwarding the characters to the host or network.
                       anxpImask7Bits 1.3.6.1.4.1.15.2.3.7.1.16 integer read-write
When enabled, instructs the Annex to ignore the eighth bit of all received characters on the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpAttnChar 1.3.6.1.4.1.15.2.3.7.1.17 displaystring read-write
Defines a control character sequence as an attention character to return the user to the CLI prompt. The Annex-II only allows a single control character (eg. ^A), while the Annex3 and MicroAnnex allow a string of control characters to be defined (eg. ^A^B^Z).
                       anxpInputBufSize 1.3.6.1.4.1.15.2.3.7.1.18 integer read-write
The number of 256-byte blocks allocated to receive input characters from this port.
                       anxpInputIsActivity 1.3.6.1.4.1.15.2.3.7.1.19 integer read-write
Controls whether received input characters are considered as activity for the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpOutputIsActivity 1.3.6.1.4.1.15.2.3.7.1.20 integer read-write
Controls whether transmitted output characters are considered as activity for the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpInactivityTimer 1.3.6.1.4.1.15.2.3.7.1.21 integer read-write
The amount of time, in minutes, which a port can remain inactive before the Annex terminates all sessions and resets the port. A value of 0 disables the timer.
                       anxpResetIdleTimer 1.3.6.1.4.1.15.2.3.7.1.22 integer read-write
Defines whether input or output resets the idle timer for the port. Enumeration: 'input': 1, 'output': 2.
                       anxpCliInactivity 1.3.6.1.4.1.15.2.3.7.1.23 integer read-write
The amount of time, in minutes, that the Annex waits before hanging up the serial port after it becomes idle. A value of 0 turns off the timer. A value of 255 means immediate, which causes the Annex to hang up the port immediately after exiting from the last job.
                       anxpCliSecurity 1.3.6.1.4.1.15.2.3.7.1.24 integer read-write
This parameter controls whether security is enabled for the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpConnectSecurity 1.3.6.1.4.1.15.2.3.7.1.25 integer read-write
This parameter controls whether the host-based security policy is enabled for access from the port to the network. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpPortServerSecurity 1.3.6.1.4.1.15.2.3.7.1.26 integer read-write
This parameter controls whether the host-based security policy is enabled for access to the port from the port server. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpPortPassword 1.3.6.1.4.1.15.2.3.7.1.27 displaystring read-write
This parameter defines a password for the port for local password protection.
                       anxpUserName 1.3.6.1.4.1.15.2.3.7.1.28 displaystring read-write
A string defining the user name for the user of the serial port.
                       anxpDedicatedAddr 1.3.6.1.4.1.15.2.3.7.1.29 ipaddress read-write
When the anxpMode parameter is set to dedicated, this parameter defines the Internet address of the host to which this port can connect to.
                       anxpDedicatedPort 1.3.6.1.4.1.15.2.3.7.1.30 displaystring read-write
The application name or TCP port number to which this port can connect when the anxpMode parameter is set to dedicated. The allowed application names are 'telnet', 'rlogin', 'login', 'call', and 'mls'.
                       anxpPrompt 1.3.6.1.4.1.15.2.3.7.1.31 displaystring read-write
This parameter defines a port-specific prompt.
                       anxpTermVar 1.3.6.1.4.1.15.2.3.7.1.32 displaystring read-write
A string defining the type of terminal attached to the serial port.
                       anxpNewLineTerm 1.3.6.1.4.1.15.2.3.7.1.33 integer read-write
This parameter controls whether a carriage return is echoed as just a carriage return (enabled), or whether the carriage return is echoed as a carriage return and line feed. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpEcho 1.3.6.1.4.1.15.2.3.7.1.34 integer read-write
This parameter controls whether the Annex echoes all characters as they are received from the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpMapToLower 1.3.6.1.4.1.15.2.3.7.1.35 integer read-write
When enabled, the Annex translates all upper case characters to lower case as they are received from the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpMapToUpper 1.3.6.1.4.1.15.2.3.7.1.36 integer read-write
When enabled, the Annex translates all lower case characters to upper case as they are transmitted to the port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpHardwareTabs 1.3.6.1.4.1.15.2.3.7.1.37 integer read-write
When enabled, this parameter allows the Annex to expand ASCII tab characters. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpCharErase 1.3.6.1.4.1.15.2.3.7.1.38 integer read-write
This parameter controls whether the Annex echoes the character erase and word erase characters for a video terminal (enabled) or for a hard-copy terminal (disabled). Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpLineErase 1.3.6.1.4.1.15.2.3.7.1.39 integer read-write
This parameter controls whether the Annex echoes the line erase character for a video terminal (enabled) or for a hard-copy terminal (disabled). Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpEraseChar 1.3.6.1.4.1.15.2.3.7.1.40 displaystring read-write
Defines the character erase control character sequence.
                       anxpEraseWord 1.3.6.1.4.1.15.2.3.7.1.41 displaystring read-write
Defines the word erase control character sequence.
                       anxpEraseLine 1.3.6.1.4.1.15.2.3.7.1.42 displaystring read-write
Defines the line erase control character sequence.
                       anxpRedisplayLine 1.3.6.1.4.1.15.2.3.7.1.43 displaystring read-write
Defines the reprint line control character sequence.
                       anxpToggleOutput 1.3.6.1.4.1.15.2.3.7.1.44 displaystring read-write
Defines the flush control character used to flush the output buffer.
                       anxpTelnetEscape 1.3.6.1.4.1.15.2.3.7.1.45 displaystring read-write
Defines the control character that returns the user to the telnet: prompt when running the CLI telnet command.
                       anxpNeedDsr 1.3.6.1.4.1.15.2.3.7.1.46 integer read-write
Specifies whether the DSR signal needs to be asserted when connecting to a slave port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpTelnetCRLF 1.3.6.1.4.1.15.2.3.7.1.47 integer read-write
Defines what characters are transmitted out the port to the network when the End-of-Line character is sensed. 'enabled' means transmit Line-Feed and Carriage-Return. 'disabled' means transmit Carriage-Return and NULL. The default is enabled. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpLatbEnable 1.3.6.1.4.1.15.2.3.7.1.48 integer read-only
Controls interpretation of LAT Data-B packets received from host. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpSlipSecure 1.3.6.1.4.1.15.2.3.7.1.49 integer read-only
If anxEnableSecurity is not set, this parameter selects slip session logging. If anxEnableSecurity is set, this parameter permits slip access only from secure ports. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpNetLocalAddr 1.3.6.1.4.1.15.2.3.7.1.50 ipaddress read-write
The Internet address for the Annex's side of the point-to-point (SLIP or PPP) link.
                       anxpNetRemoteAddr 1.3.6.1.4.1.15.2.3.7.1.51 ipaddress read-write
The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link.
                       anxpSlipSubnetMask 1.3.6.1.4.1.15.2.3.7.1.52 ipaddress read-write
The subnet mask for this SLIP interface.
                       anxpSlipLoadDumpHost 1.3.6.1.4.1.15.2.3.7.1.53 ipaddress read-write
The Internet address of the host from which the Annex receives a load or to which the Annex sends a dump over the SLIP interface.
                       anxpNetMetric 1.3.6.1.4.1.15.2.3.7.1.54 integer read-write
This parameter defines the hop count to the remote end of the SLIP or PPP interface.
                       anxpSlipAllowDump 1.3.6.1.4.1.15.2.3.7.1.55 integer read-write
This parameter defines whether the Annex is allowed to dump across a SLIP link. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpSlipDoCompression 1.3.6.1.4.1.15.2.3.7.1.56 integer read-write
When enabled, the Annex will start TCP/IP header compression on this SLIP link. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpSlipAllowCompression 1.3.6.1.4.1.15.2.3.7.1.57 integer read-write
When enabled, the Annex will use TCP/IP header compression on this SLIP link only if the other end of the SLIP link initiates the compression. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpSlipMtuSize 1.3.6.1.4.1.15.2.3.7.1.58 integer read-write
Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). The default is large. Enumeration: 'large': 1, 'small': 2.
                       anxpSlipNoIcmp 1.3.6.1.4.1.15.2.3.7.1.59 integer read-write
When enabled, the Annex will discard any ICMP packets directed to this SLIP link. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpSlipTos 1.3.6.1.4.1.15.2.3.7.1.60 integer read-write
When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpPppMru 1.3.6.1.4.1.15.2.3.7.1.61 integer read-write
This parameter defines the maximum receive unit in bytes. The default value is 1500.
                       anxpPppAcm 1.3.6.1.4.1.15.2.3.7.1.62 displaystring read-write
This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A bit on in the mask indicates the character must be escaped. The mask should be specified as an 8 hex character string (0x1F000000 and 1F000000 are both acceptable).
                       anxpPppSecurityProto 1.3.6.1.4.1.15.2.3.7.1.63 integer read-write
Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_security (anxEnableSecurity) must be enabled before authentication is performed. The default is none Enumeration: 'pap': 2, 'none': 1.
                       anxpPppUserRemote 1.3.6.1.4.1.15.2.3.7.1.64 displaystring read-write
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either if the username is defined or if the username is not defined.
                       anxpPppPasswdRemote 1.3.6.1.4.1.15.2.3.7.1.65 displaystring read-write
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either if the password is defined or if the password is not defined.
                       anxpLatAuthGroupVal 1.3.6.1.4.1.15.2.3.7.1.66 displaystring read-write
This port parameter specifies which remote group codes are accessible to a user on a particular Annex port. Each port has its own set of group codes.
                       anxpPppDialupAddr 1.3.6.1.4.1.15.2.3.7.1.67 integer read-write
When enabled, the Annex requests the PPP dialup addresses from the host-based ACP. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpBanner 1.3.6.1.4.1.15.2.3.7.1.68 integer read-write
Specifies whether the Annex banner and message- of-the-day are displayed on the port. The default is enabled. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpPsHistory 1.3.6.1.4.1.15.2.3.7.1.69 integer read-write
Specifies how much data to buffer on a slave port.
                       anxpLocation 1.3.6.1.4.1.15.2.3.7.1.70 displaystring read-write
A descriptive string for a this port. This string is displayed by the CLI who command.
                       anxpType 1.3.6.1.4.1.15.2.3.7.1.71 integer read-write
The type of device attached to the port. The default is hardwired. Enumeration: 'terminal': 3, 'dialin': 1, 'modem': 4, 'hardwired': 2, 'printer': 5.
                       anxpCliImask7 1.3.6.1.4.1.15.2.3.7.1.72 integer read-write
Defines whether input at the CLI is masked to 7 bitx. The default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.
           parallelport 1.3.6.1.4.1.15.2.4
               anxpParaPorts 1.3.6.1.4.1.15.2.4.1 integer read-only
The number of parallel ports on this Annex.
               anxpParaPortTable 1.3.6.1.4.1.15.2.4.2 no-access
Table of parallel port parameters.
                   anxpParaPortEntry 1.3.6.1.4.1.15.2.4.2.1 no-access
The Annex parallel port configuration parameters.
                       anxpParaPortIndex 1.3.6.1.4.1.15.2.4.2.1.1 integer read-only
A unique number from 1 to anxpParaPorts that identifies each parallel port.
                       anxpParaPortHardwareTabs 1.3.6.1.4.1.15.2.4.2.1.2 integer read-write
This parameter controls whether the Annex will send a tab character to the printer. If disabled, the tab is replaced with spaces. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpParaPortMapToUpper 1.3.6.1.4.1.15.2.4.2.1.3 integer read-write
When enabled, the Annex translates all lower case characters to upper case before transmitting the characters to the printer port. Enumeration: 'disabled': 2, 'enabled': 1.
                       anxpParaPortPrinterWidth 1.3.6.1.4.1.15.2.4.2.1.4 integer read-write
The defined maximum number of characters per printer line.
                       anxpParaPortInterface 1.3.6.1.4.1.15.2.4.2.1.5 integer read-write
The type of printer attached to the port. Enumeration: 'dataproducts': 2, 'centronics': 1.
                       anxpParaPortSpeed 1.3.6.1.4.1.15.2.4.2.1.6 integer read-write
The printer speed on the Micro-Annex. Enumeration: 'high-speed': 2, 'normal': 1.
           annexconfig 1.3.6.1.4.1.15.2.5
               anxInetAddr 1.3.6.1.4.1.15.2.5.1 ipaddress read-write
The Internet address of the Annex.
               anxPrefLoadAddr 1.3.6.1.4.1.15.2.5.2 ipaddress read-write
The preferred load address for the Annex.
               anxPrefDumpAddr 1.3.6.1.4.1.15.2.5.3 ipaddress read-write
The preferred dump address for the Annex.
               anxLoadDumpGateway 1.3.6.1.4.1.15.2.5.4 ipaddress read-write
The Internet address of a gateway used when the preferred load or dump host is on a different network or subnet.
               anxLoadDumpSeq 1.3.6.1.4.1.15.2.5.5 displaystring read-write
Lists the available network interfaces and the order that the Annex uses them when doing a down-line load or up-line dump.
               anxLoadBcast 1.3.6.1.4.1.15.2.5.6 integer read-write
This parameter defines whether the Annex broadcasts for the config or the motd files if they were not found on the preferred load host. Enumeration: 'disabled': 2, 'enabled': 1.
               anxServerCap 1.3.6.1.4.1.15.2.5.7 displaystring read-write
Defines whether the Annex can act as a file server host for another Annex. The allowable values are 'all', 'none' (the default), or one or more of the following names separated by commas: 'config', 'motd', 'image'.
               anxTimeBcast 1.3.6.1.4.1.15.2.5.8 integer read-write
This parameter defines whether the Annex broadcasts for the time if the preferred load host does not provide a time server. Enumeration: 'disabled': 2, 'enabled': 1.
               anxBcastAddr 1.3.6.1.4.1.15.2.5.9 ipaddress read-write
The Internet address used by the Annex when sending broadcasts.
               anxSubnetMask 1.3.6.1.4.1.15.2.5.10 ipaddress read-write
The Internet subnet mask.
               anxAuthAgent 1.3.6.1.4.1.15.2.5.11 integer read-write
This parameter controls whether the Annex can send an ICMP Address Mask Reply to a received ICMP Address Mask Request. Enumeration: 'disabled': 2, 'enabled': 1.
               anxMaxVcli 1.3.6.1.4.1.15.2.5.12 integer read-write
The maximum number of virtual CLI connections allowed by the Annex at any one time. 0 means the Annex does not allow VCLI connections. 255 allows the Annex to maintain an unlimited number of VCLI connections.
               anxIpEncapType 1.3.6.1.4.1.15.2.5.13 integer read-write
This parameter specifies whether the Annex encapsulates IP packets in the Ethernet format or the IEEE 802.2/802.3 Data Link Layer format. Enumeration: 'ethernet': 1, 'ieee802': 2.
               anxNameServer1Type 1.3.6.1.4.1.15.2.5.14 integer read-write
The name service type used by the primary nameserver host. Enumeration: 'none': 1, 'ien116': 2, 'dns': 3.
               anxNameServer1Addr 1.3.6.1.4.1.15.2.5.15 ipaddress read-write
The Internet address of the primary nameserver host.
               anxNameServer2Type 1.3.6.1.4.1.15.2.5.16 integer read-write
The name service type used by the secondary nameserver host. Enumeration: 'none': 1, 'ien116': 2, 'dns': 3.
               anxNameServer2Addr 1.3.6.1.4.1.15.2.5.17 ipaddress read-write
The Internet address of the secondary nameserver host.
               anxNameServerBcast 1.3.6.1.4.1.15.2.5.18 integer read-write
This parameter controls whether the Annex broadcasts a name server request if the preferred name servers do not respond. Enumeration: 'disabled': 2, 'enabled': 1.
               anxRwhod 1.3.6.1.4.1.15.2.5.19 integer read-write
Defines whether the Annex listens for RWHO broadcasts when building its host table. Enumeration: 'disabled': 2, 'enabled': 1.
               anxMinUniqueHostNames 1.3.6.1.4.1.15.2.5.20 integer read-write
Defines whether the Annex minimum uniqueness feature is available. Enumeration: 'disabled': 2, 'enabled': 1.
               anxHostTableSize 1.3.6.1.4.1.15.2.5.21 integer read-write
Defines the number of entries in the Annex host table. 0 indicates no host table. 251 sets no limit on the size of the table.
               anxRouted 1.3.6.1.4.1.15.2.5.22 integer read-write
Defines whether the RIP-listener of the routing daemon on the Annex is enabled. Enumeration: 'disabled': 2, 'enabled': 1.
               anxEnableSecurity 1.3.6.1.4.1.15.2.5.23 integer read-write
This parameter controls whether the Annex security system is enabled. Enumeration: 'disabled': 2, 'enabled': 1.
               anxPassword 1.3.6.1.4.1.15.2.5.24 displaystring read-write
Setting this parameter changes the Annex's administration password. Reading this parameter will return either if the password is defined or if the password is not defined.
               anxSecurServer1Addr 1.3.6.1.4.1.15.2.5.25 ipaddress read-write
The Internet address of the primary host where the Annex sends its security requests.
               anxSecurServer2Addr 1.3.6.1.4.1.15.2.5.26 ipaddress read-write
The Internet address of the secondary host where the Annex sends its security requests.
               anxNetTurnAround 1.3.6.1.4.1.15.2.5.27 integer read-write
The amount of time (in seconds) that the Annex waits for a response from a security server.
               anxSecurBcast 1.3.6.1.4.1.15.2.5.28 integer read-write
This parameter controls whether the Annex will broadcast its security requests when neither of the preferred security servers are available. Enumeration: 'disabled': 2, 'enabled': 1.
               anxVcliSecurity 1.3.6.1.4.1.15.2.5.29 integer read-write
This parameter controls whether the Annex performs user validation on the virtual CLI connections. Enumeration: 'disabled': 2, 'enabled': 1.
               anxVcliPassword 1.3.6.1.4.1.15.2.5.30 displaystring read-write
This parameter defines a password used by the Annex when setting up a virtual CLI connection.
               anxAcpKey 1.3.6.1.4.1.15.2.5.31 displaystring read-write
This parameter defines the Annex's encryption key used when exchanging messages between the Annex and the security server.
               anxSysLogMask 1.3.6.1.4.1.15.2.5.32 displaystring read-write
Defines the priority levels of events logged in the Annex syslog file. The allowable values are 'all', 'none', or one or more of the following level names separated by commas: 'emergency', 'alert', 'critical', 'error', 'warning', 'notice', 'info', 'debug'
               anxSysLogFacility 1.3.6.1.4.1.15.2.5.33 integer read-write
This parameter defines the 4.3BSD syslog facility used in logging the Annex messages. Enumeration: 'loglocal0': 17, 'loglocal1': 18, 'loglocal2': 19, 'loglocal3': 20, 'loglocal4': 21, 'loglocal5': 22, 'loglocal6': 23, 'loglocal7': 24.
               anxSysLogHost 1.3.6.1.4.1.15.2.5.34 ipaddress read-write
The Internet address of the host configured to log Annex messages.
               anxCliPrompt 1.3.6.1.4.1.15.2.5.35 displaystring read-write
The string used by the Annex to prompt all CLI users.
               anxMotdFile 1.3.6.1.4.1.15.2.5.36 displaystring read-write
The host file name that contains the message-of-the-day for the Annex.
               anxTftpDirName 1.3.6.1.4.1.15.2.5.37 displaystring read-write
Specifies the directory name to be prepended to all files (boot image, motd, macros, etc.) when booting via TFTP.
               anxTftpDumpName 1.3.6.1.4.1.15.2.5.38 displaystring read-write
The full pathname of the TFTP dump file, if any.
               anxTimeZone 1.3.6.1.4.1.15.2.5.39 integer read-write
Defines the timezone where the Annex resides in minutes west of GMT.
               anxDaylightSavings 1.3.6.1.4.1.15.2.5.40 integer read-write
Defines the daylight savings time for the geographic location of the Annex. Enumeration: 'westeuropean': 3, 'canadian': 6, 'none': 8, 'us': 1, 'british': 7, 'easteuropean': 5, 'mideuropean': 4, 'australian': 2.
               anxLatKey 1.3.6.1.4.1.15.2.5.41 displaystring read-write
The Annex specific LAT key used to enable or disable the LAT protocol.
               anxCircuitTimer 1.3.6.1.4.1.15.2.5.42 integer read-write
The time interval in tens of milliseconds between the transmission of LAT packets.
               anxFacilityNum 1.3.6.1.4.1.15.2.5.43 integer read-write
The LAT facility number.
               anxLatGroupVal 1.3.6.1.4.1.15.2.5.44 displaystring read-write
The Annex LAT group code for permitting access to LAT services. To access a specific LAT service, the Annex must have at least one enabled group code match the service's set group codes. The Annex will not maintain any information about unauthorized services. The value is displayed as a string of hex characters with each bit defining whether a specific group is enabled or disabled.
               anxKeepAliveTimer 1.3.6.1.4.1.15.2.5.45 integer read-write
The time interval, in seconds, between the transmission of identification packets during times of network inactivity.
               anxReXmitLimit 1.3.6.1.4.1.15.2.5.46 integer read-write
The number of times to retransmit a packet before notifying the user of a network failure.
               anxServerName 1.3.6.1.4.1.15.2.5.47 displaystring read-write
A string of up to 16 characters used to name the Annex in the LAT protocol.
               anxServiceLimit 1.3.6.1.4.1.15.2.5.48 integer read-write
This parameter defines the upper bound on the number of services that the Annex can maintain in its local service table.
               anxConfigFile 1.3.6.1.4.1.15.2.5.49 displaystring read-write
The name of the host file that contains the alias and menu entries.
               anxLatVcliGroupVal 1.3.6.1.4.1.15.2.5.50 displaystring read-write
This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same group code. The value is displayed as a string of hex characters with each bit defining whether a specific group is enabled or disabled.
               anxLatQueueMax 1.3.6.1.4.1.15.2.5.51 integer read-write
Defines the maximum number of host requests (HIC's) that the Annex will save in its internal queue when the requested resource is not available (port busy).
               anxLatLocation 1.3.6.1.4.1.15.2.5.52 displaystring read-write
A string of up to 32 characters used to identify the location of the Annex for the LAT protocol.
               anxDisabledModules 1.3.6.1.4.1.15.2.5.53 displaystring read-write
Defines which selectable modules are currently disabled. The allowable values are 'all', 'none' or one or more of the following names separated by commas: 'admin', 'lat', 'ppp', 'slip', 'snmp', 'nameserver', 'cli-edit'. If this is a MicroAnnex ELS, the values 'ppp' and 'slip' are not valid.
               anxSysLogPort 1.3.6.1.4.1.15.2.5.54 integer read-write
Specifies the Annex port number where syslog messages are sent. If set to 0, syslog messages are not sent to an Annex port. This is independent of any host-based syslogging that may be enabled. The maximum port number allowed will depend on the highest numbered port on the specific Annex.
           annexcmds 1.3.6.1.4.1.15.2.6
               anxcBoot 1.3.6.1.4.1.15.2.6.1 integer read-write
The type of boot to be performed. To initiate a dump, this parameter needs to be set by the management station. The values stored in anxcBootImage, anxcBootTime, and anxcBootMsg are used as needed, depending on the boot type. Enumeration: 'abortschedule': 5, 'quiet': 6, 'dumpboot': 3, 'delayed': 2, 'immediate': 1, 'diagnosticboot': 4.
               anxcBootImage 1.3.6.1.4.1.15.2.6.2 displaystring read-write
The name of the image file to be used with the boot command.
               anxcBootTime 1.3.6.1.4.1.15.2.6.3 displaystring read-write
The time at which the next boot is scheduled in HH:MM format.
               anxcBootMsg 1.3.6.1.4.1.15.2.6.4 displaystring read-write
The broadcast message to be displayed when the next boot is performed.
               anxcReset 1.3.6.1.4.1.15.2.6.5 integer read-write
Writing a value to this object causes the annex to reset the appropriate subsystem. Enumeration: 'all': 1, 'motd': 3, 'virtualports': 8, 'macros': 2, 'printerport': 6, 'serialports': 7, 'security': 5, 'nameserver': 4.
               anxcBcast 1.3.6.1.4.1.15.2.6.6 integer read-write
Writing a value to this object causes the annex to send the message in anxcBcastMsg to the specified port set. Enumeration: 'all': 1, 'serial': 2, 'virtual': 3.
               anxcBcastMsg 1.3.6.1.4.1.15.2.6.7 displaystring read-write
The message to be broadcast to the Annex ports.